PRODUCT CATALOG HUGHEYANDPHILLIPS.COM

Catalog No. 1201 O b st r u c t i o n L i g h t i n g PRODUCT CATALOG HUGHEYANDPHILLIPS.COM Lighting AT GREAT HEIGHTS For 75 Years. B ro a d c a s t Te l e c o m m u n i c a t i o n s Wi n d Tu r b i n e s Ta l l S t r u c t u re s U t i l i t i e s

Hughey & Phillips Obstruction Lighting Shines Brighter. About Hughey & Phillips For more than 75 years, Hughey & Phillips, LLC products have found their place atop some of the world s most monumental architectural achievements. At Hughey & Phillips, we make a complete line of cost-effective obstruction lighting and control solutions that are proven to be highly efficient and reliable with improved maintainability and a longer operational life. Cost-effective obstruction lighting and controls solutions Highly efficient products save energy and reduce maintainability costs Stand-alone fixtures or integrated systems available for low, medium and high intensity lighting products Longer operational life keep structures illuminated and replacements costs low Hughey & Phillips is a global leader in the design and manufacturing of obstruction lighting technology. The company offers complete solutions comprised of power and lighting systems designed and manufactured in the USA. As either stand-alone fixtures or as part of an integrated system, Hughey & Phillips low, medium, and high intensity lighting solutions provide illumination for radio and television transmission towers, communications and microwave antennas, wind turbines, grain elevators, buildings, smokestacks, bridges, and other obstructions to aerial navigation as specified by the FAA, FCC, ICAO, DGAC of Mexico and Transport Canada. Advancements in LED-based obstruction lighting technologies have resulted in lighting fixtures that extend our beacon service life up to 10 times longer than incandescent bulbs with lower power consumption. Additionally, our strobes use unique parabolic reflectors/ linear strobetubes optics and integrated flashhead blocking strips to minimize ground scatter light for more community friendly lighting systems. APPLICATIONS All low intensity lights are available as single or double lights. The low intensity and medium intensity lighting are used to mark air traffic obstructions. Different lights are used for different specific applications, all-round illuminated obstruction lights with a light intensity of 10 cd (Candela) or 32 cd, flashing medium intensity lights in red or white with 2,000 cd or 20,000 cd and even high-intensity lights in white with up to 270,000 cd. In the United States the use of specific lighting is defined in the FAA Advisory Circular 70/7460-1 on the marking of obstructions. The ICAO (International Civil Aviation Organization) or Local Aviation Authority governs for national regulations. Versatile Obstruction lighting solutions for any Industry. Hughey & Phillips engineers and designs a complete line of low, medium and high intensity lighting technology solutions that provide illumination for a wide range of industries: Broadcast Telecommunications Wind Turbines Tall Structures Utilities Whether you need to illuminate radio, television or communication towers; wind turbines; buildings; smokestacks; bridges; or other obstructions to aerial navigation, Hughey & Phillips provides innovative lighting technology solutions. We have a full engineering staff providing complete support and design in optical, electrical and mechanical disciplines to customize any of our products to fit your application s unique needs. To learn more, visit www.hugheyandphillips.com Ordering Information Designed for a wide range of obstruction lighting applications, Hughey & Phillips broad line of incandescent, xenon and LED-based lighting fixtures and control solutions provide long-life operation and highly reliable performance. Contact a Hughey & Phillips representative today by visiting www.hugheyandphillips.com or by calling toll-free 877-285-4466.

Lighting Up the World s Towering Achievements. PRODUCT OVERVIEW Hughey & Phillips obstruction lights have a sturdy construction, are built to last and fulfill both national and international specifications. All our lights are completely non-corroding, low-maintenance lights. Our product portfolio includes state-of-the-art LED low and medium intensity obstruction lights as well as lights with a conventional light-source ranging from simple incandescent obstruction lights to highintensity strobe lights for special applications. Our power-saving LED lights guarantee a life span that is several times longer than conventionally equipped lights. This is achieved by a redundant circuit design and reduction of power consumption by over 90% of the normal usage of incandescent lights. Infrared (IR) LED systems are also available. Tower & Obstruction Lighting Guide The Hughey & Phillips tower and obstruction lighting guide provides the latest FAA, FCC, Transport Canada & ICAO tower and obstruction products for lighting buildings, towers, smokestacks, grain elevators or other structures, either temporary or permanent, which might present obstructions to air navigation. References will be made in this guide to FAA, FCC, Transport Canada & ICAO requirements. The specifications and guidelines referred to are the following: FAA Advisory Circular No. 150/5345-43 Specification for Obstruction Lighting Equipment FAA Advisory Circular AC 70/7460-1K obstruction Marking and Lighting FCC Rules and Regulations Part 17 construction, Marking and Lighting of Antenna Structure ICAO Aerodromes Annex 14 international Standards and Recommended Practices Transport Canada CAR 621.19 Certified by the Secretary of Communications & Transport of Mexico Copies of these documents are available from the issuing agency or by contacting Hughey & Phillips. All Hughey & Phillips products where applicable are qualified to FAA specifications AC150/5345-43. In order to maintain an FAA listing, Hughey & Phillips must undergo rigid quality review twice yearly by an independent test laboratory. MAKING THE WORLD BRIGHTER. For over 75 years, Hughey & Phillips obstruction lighting has earned a reputation for quality, dependability and innovation the world over. In fact, we ve illuminated some of the globe s highest structures on six continents. low intensity 4 MEDIUM intensity HIGH intensity international 9 22 products 26 cables 34 diagrams 40 accessories lighting 52 63 systems faa standards 76

Low intensity

LOW INTENSITY FAA Type: L-810 Steady Burn Obstruction Light HORIZON L-810 LED OBSTRUCTION LIGHT APPLICATION The Hughey & Phillips L-810 Obstruction Light provides an LED based solution to the FAA L-810 style of steady burning lights. The L-810 LED is currently available in both single and double configurations operating at 120V, 240V, 277VAC and also in a range of 9-48 VDC. Both configurations are available as original equipment or as a direct replacement to the existing socket/lamp/lens on H&P L-810 Incandescent OB2x Series obstruction lights. FAA Type: L-810 Steady Burn Obstruction Light ICAO Type: Low Intensity Type B Obstacle Light ETL Certified: FAA AC 150 45-43F Compliant to: ICAO Annex 14, CAR 621.19, MIL-C-7989 Features: LED based obstruction lights last over 15 times longer than an incandescent light Approximately 94% less power than 116 Watt standard incandescent lamp 4 Watt Power Consumption (AC version) / 3.4 Watts (DC Version) Available in both side and bottom conduit hubs at ¾ and 1 NPT Weather resistant lamp assembly & housing Self-contained wiring compartment on double units eliminates additional boxes Operates as a steady burn or flashing light Resistant to shock and vibration Direct replacement for existing incandescent fixtures 5 Year Warranty Photometric Specifications Beam Spread: 360 Horizontal, 10 Minimum Vertical Effective Intensity: > 32 Candela Mechanical Specifications Base Material: Cast Aluminum with aviation red powder coat Lens: Heat resistant clear glass Single: 8 x 5.5 x 5.5 (H x W x L), 2 lbs. Double: 8 x 5.5 x 11.5 (H x W x L), 6 lbs. Environmental Specifications Temperature: -55 C to +55 C (-67 F to 130 F) Humidity: 95% Relative Humidity Miscellaneous: Will withstand exposure to wind-blown rain from any direction, salt-laden atmosphere and indspeeds of 240 kph (150 mph). Part Number Description 45-1000-001 L-810 LED 95-277VAC SGL BOT HUB 3/4 45-1001-001 L-810 LED 95-277VAC SGL BOT HUB 1 45-1002-001 L-810 LED 95-277VAC SGL SIDE HUB 3/4 45-1003-001 L-810 LED 95-277VAC SGL SIDE HUB 1 45-1004-001 L-810 LED 95-277VAC DBL BOT HUB 3/4 45-1005-001 L-810 LED 95-277VAC DBL BOT HUB 1 45-1006-001 L-810 LED 95-277VAC DBL SIDE HUB 3/4 45-1007-001 L-810 LED 95-277VAC DBL SIDE HUB 1 45-1008-001 L-810 LED 9-48VDC SGL BOT HUB 3/4 45-1009-001 L-810 LED 9-48VDC SGL BOT HUB 1 45-1010-001 L-810 LED 9-48VDC SGL SIDE HUB 3/4 45-1011-001 L-810 LED 9-48VDC SGL SIDE HUB 1 45-1012-001 L-810 LED 9-48VDC DBL BOT HUB 3/4 45-1013-001 L-810 LED 9-48VDC DBL BOT HUB 1 45-1014-001 L-810 LED 9-48VDC DBL SIDE HUB 3/4 45-1015-001 L-810 LED 9-48VDC DBL SIDE HUB 1 Spare Parts Description 45-0001-001 L-810 LIGHT MODULE 95-277VAC 45-0002-001 L-810 LIGHT MODULE 9-48VDC A6A0008AG NEOPRENE GASKET B6A0008AA LENS HOLDER w/7 CHAIN 6 HUGHEYANDPHILLIPS.COM

LOW INTENSITY FAA Type: L-810 Steady Burn Obstruction Light INCANDESCENT OBSTRUCTION LIGHTS APPLICATION The OB20 and OB21 single obstruction lights are equipped with a screw base lamp receptacle. The fixtures are cast aluminum and utilize flange type red fresnel lenses. The fixtures are available with either bottom entrance (OB20) or side entrance (OB21) for 3/4 or 1 conduit fittings. The fixtures are suitable for use with 120 or 230 VAC lamps. Certified to: FAA AC 150/5345-43F Compliant to: Transport Canada CAR 621.19 ICAO Annex 14 USAF AFMAN 32-1076 Models OB20A31 OB20A41 OB21A31 OB21A41 3/4 bottom conduit entrance 1 bottom conduit entrance 3/4 side conduit entrance 1 side conduit entrance Photometric Specifications Beam Spread: 360 Horizontal, 10 Minimum Vertical Effective Intensity: >32 Candela Mechanical Specifications Base Material: Cast aluminum with aviation red powder coat Lens: Heat resistant glass, red. Single Obstruction Light Dimensions: 230mm H x 140mm W x 140mm L (9 H x 5.5 W x 5.5 L) Weight: 1.8 Kg (4 Pounds) Environmental Specifications Temperature: -55 C to +55 C (-67 F to 130 F) Humidity: 95% Relative Humidity Miscellaneous: Will withstand exposure to wind-blown rain from any direction, salt-laden atmosphere and indspeeds of 240 kph (150 mph). Spare Parts and Accessories LH116120GE Lamp 120 VAC, 116 Watts FL02B02810 Red Fresnel Lens XLCB4S200 Lamp Receptacle A6A0008AG Neoprene Gasket LH116230 DT Lamp 120 VAC, 116 Watts B6A0008AA Lens Holder w/7 Chain 877.285.4466 Toll Free 7

LOW INTENSITY FAA Type: L-810 Steady Burn Obstruction Light DOUBLE INCANDESCENT OBSTRUCTION LIGHTS APPLICATION The OB22 and OB24 double obstruction lights are equipped with two screw base lamp receptacles. The fixtures are cast aluminum and utilize flange type red fresnel lenses. The fixtures are available with either side entrance or bottom entrance for 3/4 or 1 conduit fittings. The fixtures are suitable for use with 120 and 230 VAC lamps. Models OB22A31 OB22A41 OB24A31 OB24A41 3/4 bottom conduit entrance 1 bottom conduit entrance 3/4 side conduit entrance 1 side conduit entrance Double Obstruction Lights With Automatic Transfer Relay In many circumstances it is highly desirable, or required, to employ a lamp transfer relay with a double obstruction light. Upon failure of the first lamp, the relay will transfer power to the second, or standby lamp. The relay is mounted within the fixture base. This relay is of the single pole, single throw, normally closed type. Only one lamp in the double obstruction light is energized when a transfer relay is used. The fixtures are suitable for use with 120 and 230 VAC lamps. Models OB22A41TM1 OB24A41TM1 3/4 or 1 bottom conduit entrance 3/4 or 1 side conduit entrance Photometric Specifications Beam Spread: 360 Horizontal, 3 Minimum Vertical Effective Intensity: > 32 Candela Mechanical Specifications Base Material: Cast aluminum with aviation orange, powdercoat paint finish Lens: Heat resistant glass, red Double Obstruction Light Dimensions: 235mm H x 140mm W x 292mm L (9.25 H x 5.5 W x 11.5 L) Weight: 3.75 Kg (8.25 Pounds) Environmental Specifications Temperature: -55 C to +55 C (-67 F to 130 F) Humidity: 95% Relative Humidity Miscellaneous: Will withstand exposure to wind-blown rain from any direction, salt-laden atmosphere and windspeeds of 240 kph (150 mph) Spare Parts and Accessories LH116120GE Lamp 120 VAC, 116 Watts FL02B02810 Red Fresnel Lens XLCB4S200 Lamp Receptacle A6A0008AG Neoprene Gasket LH116230 DT Lamp 120 VAC, 116 Watts 6A0013SK3 Transfer Relay Assembly B6A0008AA Lens Holder w/7 Chain 8 HUGHEYANDPHILLIPS.COM

medium intensity

MEDIUM INTENSITY FAA Type: L-864, L-865, and L-866 Medium Intensity Lighting HORIZON Series LED strobe system Description The Horizon Dual Medium Intensity LED Strobe System provides daytime white and nighttime red lights in one unit. Its self-contained power supply, with available GPS sync and day/night sensor, simplifies wiring but also accepts external signals if desired. Advanced features include advanced LED modules, cutting edge optics, individual LED monitoring/ bypass, and active lightning protection (patent pending). The unit also monitors the system and provides a NO or NC alarm contact upon any system failure. Application Medium intensity obstruction lighting systems are typically used on structures between 150 (45m) and 500 (150m) above ground level to provide aviation safety. The use of a medium intensity white strobe during the daytime typically eliminates the need to paint the structure with aviation orange and white stripes. The use of a red flashing beacon at night provides a community friendly light. Hughey & Phillips medium intensity obstruction lights are designed for lighting tall structures such as communication, television and radio towers, wind turbines, smokestacks, cooling towers, tall buildings, catenary river crossings and bridges. FAA Type: L864, L865 or L-864/865 Medium Intensity Lighting ICAO Type: Type A/B Medium Intensity Obstacle Light ETL Certified: FAA Advisory Circular 150/5345-43 Compliant for use with: ICAO Annex 14, MIL-C-7989 DGAC of Mexico, CAR 621.19 Photometric Specifications Day Mode (White): 20,000 candela ± 25% Night Mode (White or Red): 2,000 candela ± 25% Beam Spread: 3 minimum Horizontal Coverage: 360, omni-directional Flash Rate: 40 FPM Day & White Night 24 FPM Night Red Environmental Specifications Temperature: -40 C to +55 C (-40 F to 130 F) Humidity: 95% Relative Humidity Miscellaneous: Will withstand exposure to wind-blown rain from any direction, salt-laden atmosphere and windspeeds of 240 kph (150 mph) Mechanical Weight, Flashhead: 8 kg (17 lbs) Flashhead Lens Material: High Temp/UV Resistant Acrylic Electrical Input Voltages: 120, 230/240, 277, 480 VAC Input Frequencies: 50 or 60 Hz Power Consumption, Day: 25 Watts Power Consumption, Night: 15 Watts 10 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-864, L-865, and L-866 Medium Intensity Lighting HORIZON Series FeatuRES Original Equipment Manufacturer Single Flashhead construction Failsafe Redundancy GPS Synchronization Available IR Capability Available Wiring Compatibility Interchangeable LED Modules Cutting Edge Optics design Lightest Flashhead Universal Input benefits Designed, engineered and manufactured by Hughey & Phillips One source for fixtures and complete lighting systems Compact design for dual (red/white) operation Automatic switching for nighttime redundancy of dual systems Built In GPS SYNC module Viewable with NVG Goggles Existing wiring can be used for retrofit applications Environmentally sealed connector Fewest number of control wiring on the market Single screw access Built-in Safety interlock switch Fully field serviceable unit H&P exclusively designed Eklipse optics package Community friendly lighting system 17 lbs Ease of handling and installation operating voltage of 95-277 VAC, 50/60Hz These specifications are subject to change. dimensions Part Number Description 50-0002-001 FAA Type L-864, 95-277VAC 50/60Hz 50-0003-001 FAA Type L-865, 95-277VAC 50/60Hz 50-0004-001 FAA Type L-866, 95-277VAC, 50/60Hz 50-0005-001 FAA Type L-864/865, 95-277VAC 50/60Hz 877.285.4466 Toll Free 11

MEDIUM INTENSITY FAA Type: L-864 Medium Intensity Lighting MODEL KG 114 300 mm Beacon For Airport and Obstruction Lighting Application Model KG 114 300mm Beacon is approved as a marker light for obstructions to air navigation such as television, radio, microwave and transmission line towers, bridges, water tanks, stacks and other tall structures as specified by the FAA. Model KG 114 300mm Beacon is in full compliance with FAA Beacon requirements for marking of obstructions to air navigation. Meets ICAO Requirements & Transport Canada Features Constructed of heavy aluminum casting, Model KG 114 300mm Beacon is completely weatherproof, and features: Concave base: with drain port at lowest point prevents accumulation of moisture from condensation. Hinged center frame: hinged at the center between the upper and lower lens assemblies to provide ready access for inspection and lamp replacement. The hinge rings, neoprene gasket, butterfly locking clamp, maintain a weatherproof center seal. Color filter supports: with flexible fins provide heat insulation and cushioning, thus eliminating color filter breakage from expansion and construction. Equipped with stainless hardware. IR compatible with enhanced flight vision systems that use IR energy emissions for imaging, including NVG goggles. Part No. Description FAA Designation Weight KG 114 F0001 300mm Beacon with Red Lens L864 73 lbs LH620120GE 620 Watts, 120 V Lamp LH700230HDT 700 Watts, 230 V Lamp 12 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-864 Medium Intensity Lighting MODEL KG 114 300 mm Beacon For Airport and Obstruction Lighting Descriptive Data Model KG 114 300mm Beacon is designed for service under all climatic conditions. Frame and hardware are constructed of non-ferrous materials. All the glassware is heat-resistant meeting FAA and Military Specifications. The Optical System consists of four red, heat-resistant lenses, designed to provide a definite beam through 360 O horizontally. The two lamp receptacles are mounted to properly position the two 620 or 700 watt Mogul Pre-focus Beacon lamps, thus providing correct beam distribution in accordance with FAA and Military specifications. A Three Terminal Connecting Block is mounted in the base allowing each lamp to be independently fed and monitored. Internal wiring is heat-resistant insulated flexible wire, terminates at the connecting block. Unless otherwise ordered, beacons are furnished with five feet of #12-3 Conductor Neoprene Cable, entering the base through a 1 Watertight Connector. Conduit may be used by removing the Watertight Connector and disconnecting the External Cable. Neoprene Gaskets are designed for long life under extreme temperatures. Upper Gasket Retainer, and Lower Gasket Retainer assure Weatherproof protection between lenses. 877.285.4466 Toll Free 13

MEDIUM INTENSITY FAA Type: L-865 and L-866 Medium Intensity Lighting FlashGuard 2000 FlashGuard 2000 System Description The FlashGuard 2000 Medium Intensity White Lighting System combines a daytime white strobe light and a nighttime white flashing light into a single flashhead. The system is also available as a red flashhead which can be used at night in place of red incandescent lighting, for much longer light source life. The flashhead is powered and controlled by a power supply that can be mounted remotely at the base of the structure. The power supply constantly monitors the operation of the system, and provides alarm contact closure upon any failure. The system automatically switches between day, twilight, and night intensities by the use of a calibrated photocell. FlashGuard 2000 flashheads incorporate a light blocking strip that minimizes ground scatter light, resulting in a community friendly lighting system. APPLICATION Medium Intensity obstruction lighting systems are typically used on structures between 150 (45M) and 500 (150M) above ground level to provide aviation safety. The use of a medium intensity white strobe during the daytime typically eliminates the need to paint the structure with aviation orange and white stripes. The use of a white flashing strobe at night provides an eye catching light for low flying aviators. Hughey & Phillips medium intensity obstruction lights are designed for lighting tall structures such as communication, television and radio towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. This light is compatible with Enhanced Flight Vision Systems that use IR energy emissions for imaging, including NVG goggles. FAA Type: L-864, L-865 & L-866 Medium Intensity Lighting ICAO Type: Medium Intensity Obstacle Light Applicable Specifications: Conforms to: FAA Advisory Circular AC 70/7460-1 FAA Advisory Circular AC 150/5345-43E ICAO Annex 14 Transport Canada TP 382E DGAC of Mexico 150/5345-43E Electrical Specifications AC Input Power DC Input Power Power Options Transient Protection System Status Indicators Safety 120 VAC +/- 10%, 60 Hz, 1 phase standard; 195 watts day operation, 60 watts night operation 24 VDC +/- 10%;120 watts day operation, 45 watts night operation 240, 480 VAC +/- 10%; 60 Hz or 240, 480 VAC +/- 10%, 50 Hz Transient protection is provided by: Company proprietary circuits which incorporate series resistors and zener diodes on all signal lines 5 kilovolt rated transformer, primary and secondary line to ground insulation Rectifier diode network protection by varistors Two neon lamps and four LEDs indicate system and subsystem operating status. The flashhead and power supply are both equipped with interlocks so that opening either unit interrupts the capacitor charging circuit and discharges the high voltage energy storage capacitors in the power supply to less than 50 volts within 30 seconds. Environmental Specifications Temperature Humidity Wind Wind Loading Wind Blown Rain Salt Fog -67 F (-55 C) to + 130 F (+55 C) per MIL-STD-810 95% relative humidity per MIL-STD-810 Wind speeds up to 150 mph (67 m/sec) 72 lbs (32 kg) at 150 mpg (67 m/sec) Surface area is 1.282 (0.12m2) Exposure to wind blown rain from any direction per MIL-STD-810 Exposure to salt-laden atmosphere per MIL-STD-810 optical performance specifications Beam Spread 1 Peak Flash (degrees) Intensity 2 Flash/Rate Duration 3 Mode Horizontal Vertical (candelas) (flashes/minute) (milliseconds) Day/Twilight 360 3 min 15,000 min 40-L-865 <10 25,000 max 60-L-866 Night 360 3 min 1,500 min 40 for L-865 100 to 250 2,500 max 60 for L-866 Notes: 1. The lower edge of the vertical beam spread lies between 1.5 and -0.5 with respect to the horizon. 2. Flashlamp light out meets the FAA minimum requirements of 15,000 candelas day/twilight and 1,500 candelas night for a period of not less than one year. 3. When the effective flash duration is generated with a group of short flashes, the flash rate is not less than 30 per second. 14 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-865 and L-866 Medium Intensity Lighting FlashGuard 2000 mechanical dimensions ss-175 power supply 18.50 (470) 16.19 (411) 15.50 (394) Clearance 10.50 (267) 8.63 (219) 17.25 (438) 16.26 (412) ss 120 photocontrol w/receptacle 5.00 (127) 5.00 (127) 0.44 (11) mounting hole 4 places Weight: 53 pounds (24 kilograms) 6.00 (152) 3.50 (89) 3/4 cable connector ss-120 photocontrol is removable for indoor installation 3.38 (86) ss-176 flashhead 5.00 (127) clearance 90 O 120 O flashhead globe lifts for access to flashtubes 15.92 (404) 120 O 90 O 3/4 cable connector focal plane 16.50 (419) 3.88 (98) 4.80 (122) 90 O mounting slot 0.69 x 0.81 (17 x 21) 6 places on 13.25 (337) bolt circle 15.00 (381) weight: 22 pounds (10 kilograms) bottom of flashhead for mounting with 3 or 4 fasteners Dimensions are in inches (millimeters) 877.285.4466 Toll Free 15

MEDIUM INTENSITY FAA Type: L-864, L-865, or L-866 Medium Intensity Lighting FlashGuard 2000B FlashGuard 2000B System Description The FlashGuard 2000B Medium Intensity White Lighting System combines a daytime white strobe light and a nighttime white flashing light into a single flashhead. The system is also available as a red flashhead which can be used at night in place of red incandescent lighting, for much longer light source life. The flashhead is powered and controlled by a power supply that can be mounted remotely at the base of the structure. The power supply constantly monitors the operation of the system, and provides alarm contact closure upon any failure. The system automatically switches between day, twilight, and night intensities by the use of a calibrated photocell. FlashGuard 2000B flashheads incorporate a light blocking strip that minimizes ground scatter light, resulting in a community friendly lighting system. White FG2000B APPLICATION Medium Intensity obstruction lighting systems are typically used on structures between 150 (45M) and 500 (150M) above ground level to provide aviation safety. The use of a medium intensity white strobe during the daytime typically eliminates the need to paint the structure with aviation orange and white stripes. The use of a white flashing strobe at night provides an eye catching light for low flying aviators. Hughey & Phillips medium intensity obstruction lights are designed for lighting tall structures such as communication, television and radio towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. This light is compatible with Enhanced Flight Vision Systems that use IR energy emissions for imaging, including NVG goggles. Red FG2009B FAA Type: L-864 (Red) or L-865 (White) Medium Intensity Lighting ICAO Type: Medium Intensity Obstacle Light Applicable Specifications: Conforms to: FAA Advisory Circular AC 70/7460-1 FAA Advisory Circular AC 150/5345-43 ICAO Annex 14 Transport Canada TP 382E DGAC of Mexico 150/5345-43F Photometric Specifications Day Mode (White): 20,000 candela ± 25% Night Mode (White or Red): 2,000 candela ± 25% Beam Spread: 3 minimum Horizontal Coverage: 360, omni-directional Ground Scatter: <3% Light Output at -10 Vertical Flash Rate: 40 FPM Day & White Night Mechanical Weight, Flashhead: 10 kg (22 lbs) Weight, Power Supply: 24 kg (53 lbs) Power Supply Enclosure: 304 Stainless Steel - standard. 316L Stainless Steel - optional Flashhead Lens Material: High Temp/UV Resistant Acrylic Stainless Steel - optional 316L environmental Temperature: -55 to +55 C (-67 F to +130 F) Will withstand exposure to: 95% relative humidity, wind-blown rain-direction, salt-laden atmosphere, Wind Speed - 240kph (150mph) Electrical Input Voltages: 120, 230/240, 277, 480 VAC Input Frequencies: 50 or 60 Hz Power Consumption, Day: 208 Watts Power Consumption, Night: 133 Watts Power Consumption, Backup: 77 Watts Peak Inrush Current: 7A @ 120VAC Available Alarm Contacts (form C dry-contact): Power Failure, Mode Status, Strobe Failure, Sidelight #1 Fail, Sidelight #2 Fail 16 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-864, L-865, or L-866 Medium Intensity Lighting FlashGuard 2000B System Features: Single flashhead provides white or red medium intensity operation with no moving parts Precise optics minimize ground scatter light Alarm contacts provided for connection to any monitoring system Rugged design of flashhead and power supply is suitable for outdoor installation in any climate Flashhead Features: Internally triggered Xenon strobe tubes utilized for long-life and maximum efficiency, without creating corrosive ozone Parabolic reflector optics and linear strobe tube optics combination provides very precise optics and blocks ground scatter light in both red or white operation Lens raises and locks in place, providing easy access to strobe tubes Only three components used in flashhead - minimal maintenance required at top of structure Safety interlock switch included No moving parts High temperature, UV resistant acrylic flashhead lens Power Supply Features: Provides power electronics, timing circuitry, and monitoring for lighting system Automatic day/night intensity control Manual intensity override Easily accessible components Plug-in-play circuit cards Control and monitoring for up two sidelight levels with four steady burning obstruction lights Fail-safe monitoring system with up to five remote alarm contacts Stainless steel NEMA 4X enclosure Low power consumption 877.285.4466 Toll Free 17

MEDIUM INTENSITY FAA Type: L-864 and L-865 Medium Intensity Lighting FlashGuard 3000 FlashGuard 3000 System Description The FlashGuard 3000 Medium Intensity Dual Lighting System combines a daytime white strobe light and a nighttime red flashing strobe into a single flashhead, eliminating the need for two separate lighting systems. The flashhead is powered and controlled by a power supply that can be mounted remotely at the base of the structure. The power supply constantly monitors the operation of the system, and provides alarm contact closure upon any failure. The system automatically switches between day and night intensities by the use of a calibrated photocell. FlashGuard 3000 flashheads incorporate a light blocking strip that minimizes ground scatter light, resulting in a community friendly lighting system. APPLICATION Medium intensity obstruction lighting systems are typically used on structures between 150 (45M) and 500 (150M) above ground level to provide aviation safety. The use of a medium intensity white strobe during the daytime typically eliminates the need to paint the structure with aviation orange and white stripes. The use of a red flashing beacon at night provides a community friendly light. Hughey & Phillips medium intensity obstruction lights are designed for lighting tall structures such as communication, television and radio towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. This light is compatible with Enhanced Flight Vision Systems that use IR energy emissions for imaging, including NVG goggles. FAA Type: L-864/865 Medium Intensity Lighting ICAO Type: Type A/B Medium Intensity Obstacle Light ETL Certified: FAA Advisory Circular 150/5345-43E Compliant for use with: ICAO Annex 14, MIL-C-7989 DGAC of Mexico, CAR 621.19 Electrical Specifications AC Input Power DC Input Power Power Options Transient Protection System Status Indicators System Test Controls Safety 120 VAC +/- 10%, 60 Hz, 1 phase standard; 195 watts day operation, 60 watts alternate white night operation 24 VDC +/- 10%;120 watts day and red night operation, 45 watts alternate white night operation 240, 480 VAC +/- 10%; 60 Hz or 240, 480 VAC +/- 10%, 50 Hz Transient protection is provided by: Circuits which incorporate series resistors and zener diodes on all signal lines 5 kilovolt rated transformer, primary and secondary line to ground insulation Rectifier diode network protection by varistors Two neon lamps and four LEDs indicate system and subsystem operating status. Manual override switches for remote day and night operation testing. Push button operation for testing fault circuit operation. The flashhead and power supply are both equipped with interlocks so that opening either unit interrupts the capacitor charging circuit and discharges the high voltage energy storage capacitors in the power supply to less than 50 volts within 30 seconds. Environmental Specifications Temperature Humidity Wind -67 F (-55 C) to + 130 F (+55 C) per MIL-STD-810 95% relative humidity per MIL-STD-810 Wind speeds up to 150 mph (67 m/sec) Wind Loading 105 lbs (32 kg) at 150 mpg (240 kph). Surface area is 1.98 ft 2 Wind Blown Rain Salt Fog Exposure to wind blown rain from any direction per MIL-STD-810 Exposure to salt-laden atmosphere per MIL-STD-810 optical performance specifications Beam Spread 1 Peak Flash (degrees) Intensity 2 Flash/Rate Duration 3 Mode Horizontal Vertical (candelas) (flashes/minute) (milliseconds) Day/Twilight 360 3 min 15,000 min 40-L-865 <10 25,000 max Night Red 360 3 min 1,500 min 20-40 for L-864 750 2,500 max White Night- 360 3 min 1,500 min 40 for L-865 100 to 250 Backup 2,500 max Notes: 1. The lower edge of the vertical beam spread lies between 1.5 and -0.5 with respect to the horizon. 2. Flashlamp light out meets the FAA minimum requirements of 15,000 candelas day/twilight and 1,500 candelas night for a period of not less than one year. 3. When the effective flash duration is generated with a group of short flashes, the flash rate is not less than 30 per second. 18 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-864 and L-865 Medium Intensity Lighting FlashGuard 3000 mechanical dimensions ss-177 power supply 18.50 (470) 16.19 (411) 15.50 (394) Clearance 10.50 (267) 8.63 (219) 17.25 (438) 16.26 (412) ss 120 photocontrol w/receptacle 5.00 (127) 5.00 (127) 0.44 (11) mounting hole 4 places Weight: 53 pounds (24 kilograms) 6.00 (152) 3.50 (89) 3/4 cable connector ss-120 photocontrol is removable for indoor installation 3.38 (86) ss-178 flashhead 877.285.4466 Toll Free 19

MEDIUM INTENSITY FAA Type: L-864 and L-865 Medium Intensity Lighting FlashGuard 3000B FlashGuard 3000B System Description The FlashGuard 3000B Medium Intensity Dual Lighting System combines a daytime white strobe light and a nighttime red flashing strobe into a single flashhead, eliminating the need for two separate lighting systems. The flashhead is powered and controlled by a power supply that can be mounted remotely at the base of the structure. The power supply constantly monitors the operation of the system, and provides alarm contact closure upon any failure. The system automatically switches between day and night intensities by the use of a calibrated photocell. FlashGuard 3000B flashheads incorporate a light blocking strip that minimizes ground scatter light, resulting in a community friendly lighting system. APPLICATION Medium intensity obstruction lighting systems are typically used on structures between 150 (45M) and 500 (150M) above ground level to provide aviation safety. The use of a medium intensity white strobe during the daytime typically eliminates the need to paint the structure with aviation orange and white stripes. The use of a red flashing beacon at night provides a community friendly light. Hughey & Phillips medium intensity obstruction lights are designed for lighting tall structures such as communication, television and radio towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. This light is compatible with Enhanced Flight Vision Systems that use IR energy emissions for imaging, including NVG goggles. FAA Type: L-864/865 Medium Intensity Lighting ICAO Type: Type A/B Medium Intensity Obstacle Light ETL Certified: FAA Advisory Circular 150/5345-43F Compliant for use with: ICAO Annex 14, MIL-C-7989 DGAC of Mexico, CAR 621.19 Photometric Specifications Day Mode (White): 20,000 candela ± 25% Night Mode (White or Red): 2,000 candela ± 25% Beam Spread: 3 minimum Horizontal Coverage: 360, omni-directional Ground Scatter: <3% Light Output at -10 Vertical Flash Rate: 40 FPM Day & White Night, 24 FPM Red Night Environmental Specifications Temperature: -55 C to +55 C (-67 F to 130 F) Humidity: 95% Relative Humidity Miscellaneous: Will withstand exposure to wind-blown rain from any direction, salt-laden atmosphere and indspeeds of 240 kph (150 mph). Mechanical Weight, Flashhead: 16 kg (34 lbs) Weight, Power Supply: 32 kg (70 lbs) Power Supply Enclosure: 304 Stainless Steel - standard. 316L Stainless Steel - optional Flashhead Lens Material: High Temp/UV Resistant Acrylic Electrical Input Voltages: 120, 230/240, 277, 480 VAC, 24VDC Input Frequencies: 50 or 60 Hz Power Consumption, Day: 208 Watts Power Consumption, Night: 133 Watts Power Consumption, Backup: 77 Watts Peak Inrush Current: 7A @ 120VAC Available Alarm Contacts (form C dry-contact): Power Failure, Mode Status, Strobe Failure, Sidelight #1 Fail, Sidelight #2 Fail 20 HUGHEYANDPHILLIPS.COM

MEDIUM INTENSITY FAA Type: L-864 and L-865 Medium Intensity Lighting FlashGuard 3000B System Features: Single flashhead provides white or red medium intensity operation with no moving parts Dual flashtubes and dual trigger transformers provide night time redundancy - no single point of failure in the flashhead Precise optics minimize ground scatter light Alarm contacts provided for connection to any monitoring system Rugged design of flashhead and power supply is suitable for outdoor installation in any climate Flashhead Features: Upper optics provides red flashing beacon lighting Lower optics provides medium intensity white strobe lighting Identical strobe tube for red and white eliminates extra spare parts Internally triggered Xenon strobe tubes utilized for long-life and maximum efficiency, without creating corrosive ozone Parabolic reflector optics and linear strobe tube optics combination provides very precise optics and blocks ground scatter light in both red or white operation Lens raises and locks in place, providing easy access to strobe tubes Only five components used in flashhead - minimal maintenance required at top of structure Dual flashtubes and trigger transformers provide night time redundancy Safety interlock switch included No moving parts High temperature, UV resistant acrylic flashhead lens Power Supply Features: Provides power electronics, timing circuitry, and monitoring for lighting system Automatic day/night intensity control Manual intensity override Easily accessible components Plug-in-play circuit cards Control and monitoring for up two sidelight levels with four steady burning obstruction lights Fail-safe monitoring system with up to five remote alarm contacts Stainless steel NEMA 4X enclosure Low power consumption 877.285.4466 Toll Free 21

high intensity

HIGH INTENSITY FAA Type: L-865 and L-857 StrobeGuard SS-122/125 SS-125 Obstruction Strobe Light The StrobeGuard SS-125 is a single enclosure obstruction light designed to meet or exceed the requirements of Advisory Circular 150/5345-43. The enclosures are fabricated from 304L stainless steel. All plug-in printed circuit boards are protected with a coating which meets the physical and electrical requirements of MIL-I-46058B. The SS-125 is supplied with a lightning arrestor capable of withstanding repeated 10,000 ampere current surges. Operated with the SS-122 Controller, the system is completely self-activating for monitoring and identifying any malfunctioning light and is equipped to initiate a remote alarm. The number of SS-125 obstruction lights used on an installation depends upon the type of obstruction and its height. FAA Type: L-856 High Intensity Lighting ICAO Type: Type A High Intensity Obstacle Light ETL Certified: FAA Advisory Circular AC 150/5345-43 Compliant for use with: ICAO Annex 14, Canadian Aviation Regulation 621.19 ICAO Annex 14, MIL-C-7989, DGAC of Mexico Photometric Specifications Day 270,000 candela ± 25% Twilight 20,000 candela ± 25% Night 2,000 candela ± 25% Beam Spread 3 Vertical minimum Horizontal Coverage 120 coverage Cut off Angle <3% light output at -10 Vertical Flash Rate 40 Flashes per Minute (FPM) Environmental Temperature -55 C to +55 C, -67 F to + 130 F Humidity 95% relative humidity Will withstand exposure to: Wind-blown rain from any angle Salt-laden atmosphere, Wind speed of 240kph (150mph) Mechanical Weight, Controller 11kg (24 lbs) Dimensions, Controller 14 H x 12 W x 6 D Weight, Flashhead 37kg (82 lbs) Dimensions, Flashhead 14.4 H x 16.2 W x 12.75 D Enclosure Rating 304 Stainless Steel, NEMA 4X Electrical Input Voltages 120, 208, 240, 277, 380, 480V Input Frequency 50 or 60 Hz Power Consumption 0.55kVA per flashhead 24 HUGHEYANDPHILLIPS.COM

HIGH INTENSITY FAA Type: L-865 and L-857 StrobeGuard SS-122/125 SS-122 Controller: StrobeGuard Controllers contain the flash interval and timing circuits, intensity selection controls, and monitoring receivers with status indicators required to operate the SS-125 strobe light. The controller is of modular construction with solid state circuitry for long life and ease of maintenance. StrobeGuard controllers are designed to operate up to 32 obstruction lights at distances up to 4700 feet. Each controller is equipped with the necessary manually operated controls to test all modes of operation. Digital monitor lamps are provided and illuminate when a flashhead or power supply is not operating as required. Each monitor lamp is operated in a coded mode indicating the location of the flashhead/ power supply which is malfunctioning. SS-124 Ambient Sensor: The SS-124 Light Sensor continuously monitors the ambient lighting conditions and inputs to the StrobeGuard controller the necessary information to automatically control the switching of daytime, twilight and nighttime modes of operation. The SS-124 is easy to install with the built-in mounting holes. StrobeGuard Control StrobeGuard controls contain the flash interval and timing circuits, intensity selection controls and monitoring circuitry with status indicators. The StrobeGuard control system is designed to operate up to 24 flashheads at a distance of up to 2500 feet (760 M), using a noise-resistant communications format. Each control is equipped with the necessary manually operated controls to test all modes of operation. Bi-color green/red LEDs are provided to indicate proper operation or fault of each flashhead. Features: Fail-safe monitoring system Parabolic Optics minimize ground scatter light: <3% of peak intensity at -100 Two-wire cable for sync, mode and monitoring Safety interlocks in each flashhead Long-life internally triggered strobe tubes Automatic three-level intensity control Manual intensity override Easily accessible replaceable components Plug-in-play circuit cards Remote alarm contacts Stainless steel NEMA 4X enclosure Vertical level indicator and adjustment system Low power consumption Minimal wind loading and weight IR Compatible with NVG goggles 877.285.4466 Toll Free 25

international

INTERNATIONAL PRODUCTS FOR LOW INTENSITY OBSTRUCTION LIGHTS LED LAMP E27 RTO / OTL APPLICATION The LED-lamp was designed to substitute the current 100/116W incandescent lamp in low intensity obstacle lights type RTO and OTL for the 10cd requirement Low Intensity Obstacle Lights Type A, acc. To ICAO Annex 14, table 6-3, issue July 2004. In combination with a clear lens the RTO Obstacle light with LED-Lamp E27 RTO meets ICAO Low Intensity Obstacle Light Type B (32 cd) requirement. Regulations ICAO annex 14, table 6-3, issue July 2004 CE regulations Characteristics Compact and robust design Replacement for E27 incandescent lamp Can be substituted into existing obstacle lights Long life expectancy Build-in redundancy by redundant connection of LEDs Power consumption approx. 4W Wide voltage and frequency range Technical Data Structure: LED-Lamp as replacement for incandescent lamp Number of LEDs 6 Color red Chromaticity acc. To ICAO, annex 14, appendix 1, fig. A1-1 Lamp base E27 Voltage 100V 230V AC, 50/60 Hz Power consumption approx. 4 Watt Temperature range -40OC - + 55OC Dimensions, weight, packing data LED Lamp E 27 RTO Dimensions: approx. 78.0 x 73.0 mm (h x 0) Weight: approx. 0.310 kg LED Lamp E 27 OTL Dimensions: approx. 84.0 x 73.0 mm (h x 0) Weight: approx. 0.310 kg Packing unit: 4 pieces Box dimensions: approx. 165 x 165 x 110 mm (l x w x h) Ordering information 65 873 070 LED Lamp E27 RTO, 32 cd 65 975 584 LED Lamp E27 OTL, 10 cd 28 HUGHEYANDPHILLIPS.COM

INTERNATIONAL PRODUCTS FOR LOW INTENSITY OBSTRUCTION LIGHTS LED LAMP E27 RTO / OTL 877.285.4466 Toll Free 29

INTERNATIONAL PRODUCTS OBSTACLE LIGHTING FOR WIND TURBINES LED 170W APPLICATION Night marking for wind turbines according to the national regulation for marking obstructions to air traffic Richtlinie zur Kennzeichnung von Luftfahrthindernissen issued by the German Federal Ministry of Transport, Building and Housing. Type W Red Function A pair of the flashing red obstruction lights LED170 are specified for the night marking of wind turbines higher than 100m. The timing of the LED170 flashing identifies the marked obstruction as wind turbine to the pilots of aircrafts. The system automatically switches on by the use of a calibrated photocell. In order to allow synchronization of the flashing of the LED170 lights with those on other wind turbines, the LED170 is optionally synchronized by the use of GPS. The pair of LED170 lights per wind turbine in conjunction with a separate uninterrupted power supply plus control electronics forms the flashing light system designed for an individual wind turbine. The LED170 light is maintenance free. Characteristics Maintenance free obstruction light using high-lumen LEDs High lifetime by optimized heat dissipation and low operating current of the LEDs Constant light output by compensation of temperature changes Rugged housing with self-cleaning transparent cover Mechanical interface identical to that of the FG2000/3000B light family Fault detection National regulation for marking aeronautical obstacles, part A and B Technical Data Power Supply system 690 or 230V, 50Hz Power Consumption system Approx. 400VA at start of charge Mechanical dimensions 381 x 405 mm (L x H) Weight 8.5 kg Flashhead Power Consumption 22 Watts Light Sources High performance LEDs Light Intensity >170cd Horizontal beam spread 360 Vertical beam spread Min 170cd ±5 Min 34cd ±10 Min 3,4cd ±15 Timing of flashing: 1s on - 0.5s off - 1s on - 1.5s off Ordering information 65 874 240 LED170W 230V, 50Hz 65 874 616 LED170W 690V, 50Hz 65 874 617 LED170W 230V, 50Hz, with GPS 65 874 618 LED170W 690V, 50Hz, with GPS 30 HUGHEYANDPHILLIPS.COM

INTERNATIONAL PRODUCTS OBSTACLE LIGHTING FOR WIND TURBINES LED 170W 877.285.4466 Toll Free 31

INTERNATIONAL PRODUCTS FAA Type: L-864 Medium Intensity Lighting LED 2000 APPLICATION The flashing red omni-directional medium intensity obstacle light LED 2000 is applied to mark obstacles. The LED 2000 is in compliance with ICAO, July 2004. Annex 14, Volume 1, Table 6-3, for Medium Intensity Obstacles Lights Type B and C. Steady burning operation at Type C is alternatively possible. FAA Type: L-864, AC150/5345-43F ICAO Type: Annex 14, Tables 6-3, July 2004 NATO: Stanag 3316 CE-Mark LED 2000 characteristics LED-Medium Intensity Obstacle Light 2,000cd Extremely low light emittance downwards Light intensity at -1 O Max. 1,125cd Min. 750cd Effective thermal management Steady burning operation as Type C light, up to max. environmental temperature of +55 O C Very high lifetime Redundant circuitry for LEDs technical data Construction: LED - Obstacle Light Number of LED: 28 Color of light: Red Chromaticity: according to ICAO, Annex 14, Volume 1, Figure A 1-1 Photometry: according to ICAO, Annex 14, Volume 1, Table 6-3 Medium Intensity Obstacle Light 2000cd Type B,C Main voltage: 230 V AC + 10%, -15%, 50/60 Hz Power consumption: 80 Watt in steady burning operation 40 Watt in blinking mode Temperature range: -40 O C -+ 55 O C Dimensions, weight, packing data Dimensions: 335 x 410 mm (H x O) Weight: appr. 9 kg Packing unit: 1 piece Packing size: appr. 600 x 500 x 600 mm (L x W x H) part no. 65 875 918 LED 2000 32 HUGHEYANDPHILLIPS.COM

INTERNATIONAL PRODUCTS FAA Type: L-864 Medium Intensity Lighting LED 2000 Fig 1: LED 2000 horizontal light distribution in beam centre according to ICAO Fig 2: LED 2000 horizontal light distribution at -1 O down (-1 O Cutoff condition according to ICAO) Fig 3: LED 2000 vertical light distribution according to ICAO 877.285.4466 Toll Free 33

cables

CABLES 77-2992 Cable ALUMINUM BINDER TAPE MYLAR SHIELD 11 JACKET FILLER Ø.600 ASSEMBLY Cabling - Core-minimum filler to keep as flexible as practical Outer Layer - 7 wires, items 4-10 (4 #14 + 3 #16 AWG) Cabled around the core with a 7 left hand lay Binder - 0.002 mylar tape - 25% minimum overlap Tape shield - 0.002 aluminum mylar tape - 25% minimum overlap Drain wire - Item 11 is pulled under the shield Jacket - 0.025 polythlyne - color: black Overall diameter - Ø.600 MAX SPECIFICATIONS Temperature rating 55 C to +80 C Voltage rating 600 VRMS (Conductors 2500 VRMS for electronic use) Insulated conductors UL1015 CSA TRE2 IPCEA S 61 402 Cable UL2653 CSA TR32 IPCEA S 61 402 Voltage testing Finished cable tested at 2000 VRMS between every two conductors and between each conductor and the shield. 100% test. CONDUCTORS ITEM NO. WIRE INSULATION NOM. DIA. SIZE STRANDS/AWG MATERIAL COLOR MATERIAL 4 14 AWG 19/25 COPPER BLACK TYPE B P.V.C. 600V Ø.105 5 14 AWG 19/25 COPPER WHITE TYPE B P.V.C. 600V Ø.105 6 14 AWG 19/25 COPPER RED TYPE B P.V.C. 600V Ø.105 7 14 AWG 19/27 COPPER ORANGE TYPE B P.V.C. 600V Ø.105 8 16 AWG 19/27 COPPER YELLOW TYPE B P.V.C. 600V Ø.091 9 16 AWG 19/27 COPPER GREEN TYPE B P.V.C. 600V Ø.091 10 16 AWG 19/29 COPPER VIOLET TYPE B P.V.C. 600V Ø.091 11 16 AWG 19/29 TINNED COPPER BARE DRAIN WIRE 36 HUGHEYANDPHILLIPS.COM

CABLES 77-4017 FILLER JACKET TAPE SHIELD BINDER TAPE Ø.565 ±.03 ASSEMBLY Cabling - Core- filler, as required to maintain a circular cross section Outer Layer - 6 wires, items 1-6 (2 #10 + 2 #12 + 2 #18 AWG) Cabled around the core with a 7 left hand lay Binder - overall clear polyster. 100% coverage Tape shield - overall aluminum mylar foil 100% coverage - 20% overlap Drain wire - Item 7 is 18 AWG 16 strand tinned copper Jacket - UV inhibiting polyvinyl chloride (PVC) Overall diameter - Ø.565 ±.03 SPECIFICATIONS Temperature rating 43 C to +80 C stationary 55 C to +80 C Voltage rating 600 VRMS (Conductors 2500 VRMS for electronic use) Insulated conductors CSA AWM 1/11 6DOV FTA ICEA S 61 402 Cable UL. standard 1277. Type VNTC. CSA FT4 nec 340. Sunlight resistant jacket 600 V rated Voltage testing Finished cable tested at 2000 VRMS between every two conductors and between each conductor and the shield. 100% test. CONDUCTORS ITEM NO. WIRE INSULATION NOM. DIA. PRIMARY SECONDARY SIZE STRANDS/AWG STRANDS/AWG MATERIAL COLOR MATERIAL 1 10 AWG 37/26 104/30 TINNED COPPER RED (PVC).020 NOM. WALL NYLON.005 NDM WALL Ø.177 2 10 AWG 37/26 104/30 TINNED COPPER BROWN (PVC).020 NOM. WALL NYLON.005 NDM WALL Ø.177 3 12 AWG 19/25 65/30 TINNED COPPER BLUE (PVC).015 NOM. WALL NYLON.005 NDM WALL Ø.153 4 18 AWG 16/30 16/30 TINNED COPPER GRAY (PVC).015 NOM. WALL NYLON.005 NDM WALL Ø.107 5 18 AWG 16/30 16/30 TINNED COPPER WHITE (PVC).015 NOM. WALL NYLON.005 NDM WALL Ø.107 6 12 AWG 19/25 65/30 TINNED COPPER BLACK (PVC).015 NOM. WALL NYLON.005 NDM WALL Ø.153 7 18 AWG 16/30 16/30 TINNED COPPER BARE DRAIN WIRE 877.285.4466 Toll Free 37

CABLES 77-4231 Cable ALUMINUM MYLAR SHIELD BINDER TAPE JACKET FILLER ASSEMBLY Cabling - Core-minimum filler to keep as flexible as practical Outer Layer - 10 wires, items 1-10 (3 #12 + 4 #14 + 3 #16 AWG) Cabled around the core with a 7 left hand lay Binder - 0.002 mylar tape - 25% minimum overlap Tape shield - 0.002 aluminum mylar tape - 25% minimum overlap Drain wire - Item 11 is pulled under the shield Jacket - UV inhibiting polyvinyl chloride (PVC) Black 0.060 nominal wall Overall diameter - Ø.665 ± 0.3 SPECIFICATIONS Temperature rating 55 C to +80 C Voltage rating 600 VRMS (Conductors 2500 VRMS for electronic use) Insulated conductors UL1015 CSA TRE2 IPCEA S 61 402 Cable UL2653 CSA TR32 IPCEA S 61 402 Voltage testing Finished cable tested at 2000 VRMS between every two conductors and between each conductor and the shield. 100% test. CONDUCTORS ITEM NO. WIRE INSULATION NOM. DIA. SIZE STRANDS/AWG MATERIAL COLOR MATERIAL 1 12 AWG 19/25 COPPER BLACK P.V.C. 600V Ø.124 2 12 AWG 19/25 COPPER WHITE P.V.C. 600V Ø.124 3 12 AWG 19/25 COPPER GREEN P.V.C. 600V Ø.124 4 14 AWG 19/27 COPPER BLACK P.V.C. 600V Ø.105 5 14 AWG 19/27 COPPER WHITE P.V.C. 600V Ø.105 6 14 AWG 19/27 COPPER RED P.V.C. 600V Ø.105 7 14 AWG 19/27 COPPER ORANGE P.V.C. 600V Ø.105 8 16 AWG 19/29 COPPER YELLOW P.V.C. 600V Ø.091 9 16 AWG 19/29 COPPER GREEN P.V.C. 600V Ø.091 10 16 AWG 19/29 COPPER VIOLET P.V.C. 600V Ø.091 11 18 AWG 16/30 TINNED COPPER bare DRAIN WIRE 38 HUGHEYANDPHILLIPS.COM

CABLES WC23012CLOT WC23012DLOT Type TC-Control or Instrumentation Cable PVC/Nylon Insulation with Overall PVC Jacket Cabling Three or more conductors are assembled round with fillers as needed. A nylon rip cord is inserted under the jacket for ease of stripping. Two conductors are assembled flat parallel (round, with fillers as needed, is available upon request). Overall Jacket Gas/vapor-tight Polyvinyl Chloride (black) UL1277 table 10.1 Thickness Specified herein Color Coding ICEA Method 3 Table K-2, except colors and numbers are printed on solid base colors for easy identification. Cable Identification Sizes 18 and 16 AWG Ink print on one side of jacket (size) AWG Type TC 90 C dry 75 C wet Sunlight Resistant 600V A.I.W. Corp. (UL) Direct Burial Indent print on other side of jacket (number of conductors) Sizes 14, 12, and 10 AWG Ink print on one side of jacket (size) AWG Type TC THHN or THWN cdrs. Sunlight Resistant 600V A.I.W. Corp. (UL) Direct Burial Indent print on other side of jacket (number of conductors) Construction Options Consult factory for cable specifications with appropriate shields. Cables made per Dupont Spec. SE-33.4B also available. Scope This specification covers multiconductor cables having VW-1 TFFN or THHN/THWN (PVC/Nylon) conductors with an overall gas/ vapor-tight polyvinyl chloride (PVC) jacket, conforming to Article 318 Cable Trays and Article 340 Power and Control Cable Type TC of the 1996 National Electrical Code, and Standard 1277 of Underwriters Laboratories, Inc. Meets the requirements of ICEA T-29-520 and T-30-520 flame tests as well as the 70,000 BTU Cable Tray Propagation Test per IEEE-383 and shows reserve capabilities by also pass the 210,000 BTU flame test. Rated 600 volts, 90 C dry and 75 wet. UL file no. E60749. Also meets FT4/IEEE 1202 70,000 BTU test. SPECIFICATIONS UL listed and OSHA acceptable. Recognized for use in Class 1 or 2, Division 2 hazardous locations and for installation in trays, wireways, troughs, channels, ducts and conduit. Specifically approved for direct burial, wet or dry locations and outdoors in cable trays where a sunlight resistant rating is required. Designed for control, power, lighting, telemetering, signals and relay or traffic control. Construction Conductors Bare soft annealed copper per ASTM B-3 Sizes 18 and 16 AWG (TFFN) Bunch stranded. Size 18 (16/.010 ) and Size 16 (19/.0117 ) UL-62 paragraph 10.2 Sizes 14, 12 and 10 AWG (THHN/THWN) Concentric stranded, class B (7 strands) ASTM B-8 and UL-83 table 13.1 Insulation High dieletric polyvinyl chloride UL-1581 table 50.145 (THWN 75 C) UL-1581 table 50.155 (THHN 90 C) UL-1581 table 50.155 Class 12B (TFFN 90 C) Thickness UL-83 table 15.5 for THHN/THWN UL-62 table 6.2 for TFFN Insulation Armor Nylon UL-83 paragraph 25.1 for THHN/THWN UL-62 paragraph 22.1 for TFFN Thickness UL-83 table 15.5 for THHN/THWN UL-62 paragraph 26.4 for TFFN 877.285.4466 Toll Free 39

DIAGRAMS

DIAGRAMS 9LCA001000AS INCOMING POWER SEE NOTE 1. NEUTRAL GROUND LINE PHOTOCELL RED PHOTOCELL BLACK TOWER NEUTRAL OBSTRUCTION LIGHTS (1-4 116W 120V LAMPS) Product # Description PART # AC Alarm Card, 120V, SL B b7c51paa CB1 circuit Breaker, 15A EB152771CMDW F1 Fuse, 7 Amp (some models, replaces CB1) FUFNM70G251 MC Master Card w/photocell B b7c14raa MV1-2 Metal Oxide Varistor, 150V 80 Joules MV150LA20 MV3 Metal Oxide Varistor, 24V 4 Joules MV24ZA4 SW1 Day/Night/Auto Switch SZ22030251AK TB1-E Terminal Block End (1 total) tbe230aa TB1-S Terminal Block Section (4 total) tbs213aa01a TBP Photocell Terminal Block, 2 Position tb02b038a07a 9LCA111L00AS GROUND NEUTRAL LINE TOWER GROUND BEACON (2 620W 120V LAMPS) OBS. LIGHTS (2-4 116W 120V LAMPS) LOAD BALANCE RESISTOR TOWER NEUTRAL Product # Description PART # AC Alarm Card, 120V, BCN-SL B b7c21paa CB1-3 Circuit Breaker, 15A EB152771CMDW FBP Flasher By-Pass Card, 120V B b7c31paa K1 Relay, 12V Coil, 20 A, DPDT KA120DV2022C K2-4 Solid State Relay, NO, 40A KR241DV4011R MC Master Card w/photocell B b7c11raa MV1-4 Metal Oxide Varistor, 150V 80 Joules MV150LA20 MV5 Metal Oxide Varistor, 24V 4 Joules MV24ZA4 SW1 Day/Night/Auto Switch SZ22030251AK TB1/2-E Terminal Block End (2 total) tbe230aa TB1/2-S Terminal Block Section (9 total) tbs213aa01a TBP Photocell Terminal Block, 2 Position tb02b038a07a 9LCD111000AS INPUT POWER GROUND NEUTRAL LINE TOWER GOUND STROBE LINE PHOTO LINE TOWER NEUTRAL PHOTOCELL RED BLACK Product # Description PART # AC Alarm Card, 120V, Strobe B b7c26paa CB1 circuit Breaker, 15A EB152771CMDW K1 Solid State Relay, NO, 40A KR241DV4011R MC Master Card w/photocell B b7c12raa MV1-3 Metal Oxide Varistor, 150V 80J MV150LA20 MV4 Metal Oxide Varistor, 24V 4J MV24ZA4 SW1 Day/Night/Auto Switch SZ22030251AK TB1/2-E Terminal Block End (2 total) tbe230aa TB1/2-S Terminal Block Section (8 total) tbs213aa01a TBP Photocell Terminal Block, 2 Position tb02b038a07a K1 42 HUGHEYANDPHILLIPS.COM

DIAGRAMS 9LCA233L00AS LINE 1 LINE 2 INCOMING GROUND INCOMING NEUTRAL TOWER NEUTRAL TOWER GROUND BEACON 1 (2 620W 120V LAMPS) BEACON 2 (2 620W 120V LAMPS) BEACON 3 (2 620W 120V LAMPS) LOAD BALANCE RESISTOR 1 LOAD BALANCE RESISTOR 2 LOAD BALANCE RESISTOR 3 OBS LIGHT LEVEL 1 (3-4 116W 120V LAMPS) OBS LIGHT LEVEL 2 (3-4 116W 120V LAMPS) TOWER GROUND Product # Description PART # AC1 Alarm Card, 120V, BCN-BCN-BCN B b7c24paa AC2 Alarm Card, 120V, SL-SL b7c23paa CB1-8 Circuit Breaker, 15A EB152771CMDW FAN Fan, 120V A6A1010AF2 FBP1-3 Flasher By-Pass Card, 120V B b7c31paa K1-3 Relay, 12V Coil, 20 A, DPDT KA120DV2022C K4-12 Solid State Relay, NO, 40A KR241DV4011R MC Master Card w/photocell B b7c11raa MV1-8 Metal Oxide Varistor, 150V 80 Joules MV150LA20 MV9 Metal Oxide Varistor, 24V 4 Joules MV24ZA4 PHOTOCELL BLACK AND RED SW1 Day/Night/Auto Switch SZ22030251AK TB1/2-E Terminal Block End (2 total) tbe230aa TB1/2-S Terminal Block Section (9 total) tbs213aa01a TB1-NE Terminal Block End White, Large(1 total) TBE830AA TB1-NS Terminal Block Section White, large (2 total) TBS824AA01A TBP Photocell Terminal Block, 2 Position tb02b038a07a 9LCE233L0BAS Product # Description PART # AC1 Alarm Card, 120V, OB-OB B b7c23paa AC2 Alarm Card, 120V, BCN-BCN-BCN B b7c24paa AC3 Alarm Card, 120V, ST-ST-ST B b7c28paa BC backup Card, 120V B b7c41paa CB1-1 Circuit Breaker, 15A EB152771CMDW FAN cooling Fan, 120V A6A1010AF2 FB1-3 Flasher By-Pass Card, 120V B b7c31paa K1-3 Relay, 12V Coil, 20 A, DPDT KA120DV2022C K4-12 Solid State Relay, NO, 40A KR241DV4011R K13 Relay, 120V Coil, DP3T KA121AV0532C MC Master Card w/photocell B b7c13raa MV1-12 Metal Oxide Varistor, 150V 80 Joules MV150LA20 MV13 Metal Oxide Varistor, 24V 4 Joules MV24ZA4 SW1 Day/Night/Auto Switch SZ22030251AK SYNC Strobe Sync Card B b6a1101pcb4b TB1/2-E Terminal Block End (2 total) tbe230aa TB1/2-S Terminal Block Section (18 total) tbs213aa01a TBN-E Large Terminal Block End (2 total) tbe830aa TBN-S Large Terminal Block Section (18 total) tbs824aa01a TBP Photocell Terminal Block, 2 Position tb02b038a07a 877.285.4466 Toll Free 43

DIAGRAMS 9LCE111L0BAS GROUND NEUTRAL LINE TOWER GROUND BEACON (2 620W 120V LAMPS OBS. LIGHTS (2-4 116W 120V LAMPS MEDIUM INTENSITY STROBE LOAD BALANCE RESISTOR PHOTO/HEATER LINE TOWER NEUTRAL Product # Description PART # AC Alarm Card, 120V, BCN-OB-ST B b7c25paa BC backup Card, 120V B b7c41paa CB1-4 Circuit Breaker, 15A EB152771CMDW FBP Flasher By-Pass Card, 120V B b7c31paa K1 Relay, 12V Coil, 20 A, DPDT KA120DV2022C K2-4 Solid State Relay, NO, 40A KR241DV4011R K5 Relay, 120V Coil, DPDT KA121AV0522C MC Master Card w/photocell B b7c13raa MV1-5 Metal Oxide Varistor, 150V 80 Joules MV150LA20 MV6 Metal Oxide Varistor, 24V 4 Joules MV24ZA4 SW1 Day/Night/Auto Switch SZ22030251AK TB1/2-E Terminal Block End (2 total) tbe230aa TB1/2-S Terminal Block Section (9 total) tbs213aa01a TBP Photocell Terminal Block, 2 Position tb02b038a07a RED BLACK PHOTOCELL FG2000/2000B Product # Description PART # FH1 Flashhead Complete, FG2000 (white) *277-4045E FH1 Flashhead Complete, FG2009 (red) *277-4153E FH1 Flashhead Complete, FG2000B (white) *277-5047W FH1 Flashhead Complete, FG2009B (red) *277-5047R FT1 Flashtube Assembly 12S00602 B1 base Assembly (w/gasket & lens holders) *77-4103 G1 Lens Gasket, 14 AS568A-383 G2 Lower Cover Gasket, 11.5 AS568A-380 GL1 globe Assembly, FG2000 (white) *77-4036-001 GL1 globe Assembly, FG2009 & FG2009B (red) *77-4036-003 GL1 globe Assembly, FG2000B (white) *77-4036-002 IC1-2 Insulator Cups *77-4182 FH1-6 Flashtube Holder *77-4026 S1 interlock Switch *77-2644 TB1 terminal Block Assembly *77-3965 T1 trigger Transformer *77-4040W FG3000/3000B Product # Description PART # FH1 Flashhead Complete, FG3000 *277-4173E FH1 Flashhead Complete, FG3000B *277-5004RW FT1-2 Flashtube Assembly 12S00602 B1 base Assembly (w/gasket & globe holders) *77-4103 G1 Lens Gasket, 14 AS568A-383 G2 Lower Cover Gasket, 11.5 AS568A-380 GL1 globe Assembly, FG3000 *277-5095-004 GL1 globe Assembly, FG3000B *277-5095-001 ICL insulator Cup, Lower *77-4182 ICU insulator Cup, Upper *77-4181-001 FTH Flashtube Holder *77-4026 S1 interlock Switch *77-2644 TB1 terminal Block Assembly *77-3965 K1 Trigger Transformer relay (FG3000 only) *77-4192 T1 trigger Transformer, White *77-4040W 44 HUGHEYANDPHILLIPS.COM T2 trigger Transformer, Red *77-4040R

DIAGRAMS FG2000 Product # Description PART # C1 capacitor, Resonating, 4uF *77-3911 C2 capacitor, Day, 70uF *77-3949 C3 capacitor, Night, 5uF *77-4104 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure, FG2000/3000 *77-4219 F1 input Power Fuse, 4Amp *DP-1020 HV high Voltage Board *277-3937 K1-2 Interlock & Day/Night Relay *77-2013 MB1 Mother Board *77-3967 PC Photocell *77-3259 PC1 Photocell w/socket *77-3259PCA PS1 FlashGuard 2000 PS, 120V 60Hz *277-397161A PS2 FlashGuard 2000B PS, 230V 50Hz *277-397153A R1 Power Resistor, 50ohm, 55Watt *77-3959 R2-4 Power Resistor, 20ohm, 40Watt *77-2759 S1 interlock Switch *77-2644 S2 interlock Switch Assembly *277-3990 SM1 Sync Monitor Board *277-4116 T1 Power Transformer, 120/240V 60Hz *77-3970 T1 Power Transformer, 240/480V 60Hz *77-4137 T1 Power Transformer, 240/480V 50Hz *77-4138C T2 current Sense Transformer 40000679-001 TC1 trigger Control Board *277-4123 TF1 transformer Fuse, 630mA *DP-1019 FG2000B AOL Product # Description PART # C1 capacitor, Resonating, 4uF *77-3911 C2 capacitor, Day, 70uF *77-3949 C3 capacitor, Night, 5uF C ca505b661cdg DB1 Diode Board *277-3939 SW1: AUTO-RESET TEST BUTTON HIGH VOLTAGE INDICATOR DS1 DCC Digital Controller Board 40000031-003 E1 Stainless Steel Enclosure 40000678-003 F1-F2 Input Power Fuse, 6Amp *77-1167 HV high Voltage/Trigger Board 34E00010-001 K1-2 Interlock & Day/Night Relay *77-3870 MB1 Mother Board *277-5053-002 R1 Power Resistor, 50ohm, 55Watt *77-3959 R2-4 Power Resistor, 20ohm, 40Watt *77-2759 DS1: LOGIC POWER (RED) DS2: FLASH STATUS (YELLOW) DS3: COMMUNICATION STATUS GREEN R5 Power Resistor, 1.5kohm, 50Watt RW000002 S1 interlock Switch Assembly *277-5093 T1 Power Transformer, 240/480V 60Hz *77-5066 T2 current Sense Transformer 40000679-001 T3 trigger Line Driver Board *277-5105 T4 Logic Transformer T tp000005 T5 Power Line Transformer 1A91324H34 TF1 transformer Fuse, 630mA *DP-1019 877.285.4466 Toll Free 45

DIAGRAMS FG3003 Product # Description PART # C1 capacitor, Resonating, 3uF *77-3311 C2 capacitor, Day, 40uF *77-3949 C3 capacitor, Night, 7uF *77-3982 CNV1 DC-DC Converter, 24VDC-1000VDC *77-4128 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure *77-4219 F1,F3 Input Power/Sidelight Fuse, 12Amp *77-4136 HV high Voltage Circuit Card *277-4131 K1-2 Interlock & Day/Night Relay *77-3870 MB1 Mother Board *277-4208 PC Photocell w/21 cable 12H00107 PS1 FlashGuard 3000 Power Supply, 24VDC *277-417500L R2-4 Power Resistor, 20ohm, 40Watt *77-2759 S1 interlock Switch *77-2644 SL1 Photocontroller/Sidelight Monitor Assembly 12H00109-1 SM1 Sync Monitor Board *277-4163 SW1 Interlock Switch Assembly *277-3990DC T2 current Sense Transformer 40000679-001 TB2 terminal Block Assembly *77-3965 TC1 trigger Control Board *277-4169 FG2000B Product # Description PART # C1 capacitor, Resonating, 4uF *77-3911 C2 capacitor, Day, 70uF *77-3949 C3 capacitor, Night, 5uF C ca505b661cdg DB1 Diode Board *277-3939 DCC Digital Controller Board 40000031-003 E1 Stainless Steel Enclosure 40000678-004 F1-F2 Input Power Fuse, 6Amp *77-1167 HV high Voltage/Trigger Board 34E00010-001 K1-2 Interlock & Day/Night Relay *77-3870 MB1 Mother Board *277-5053-002 R1 Power Resistor, 50ohm, 55Watt *77-3959 R2-4 Power Resistor, 20ohm, 40Watt *77-2759 R5 Power Resistor, 1.5kohm, 50Watt RW000002 S1 interlock Switch Assembly *277-5093 T1 Power Transformer, 240/480V 60Hz *77-5066 T2 current Sense Transformer 40000679-001 T3 trigger Line Driver Board *277-5105 T4 Logic Transformer T tp000005 T5 Power Line Transformer 1A91324H34 TF1 transformer Fuse, 630mA *DP-1019 46 HUGHEYANDPHILLIPS.COM

DIAGRAMS FG2009 FG2009B Product # Description PART # ALN Alarm Lockout Relay Assembly, Day (not shown) 35E00101 C1 capacitor, Resonating, 3uF *77-3311 C2 capacitor, Day, 40uF *77-3949 C3 capacitor, Night, 7uF *77-3982 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure *77-4219 F1 input Power Fuse, 10Amp *77-2040 F3 Sidelight Fuse, 4Amp *DP-1020 HV high Voltage Board *277-3937 K1-2 Interlock & Day/Night Relay *77-2013 K4 Sidelight Module Sensor *77-4196 K5 Sidelight Module Power Relay *77-4198 MB1 Mother Board *277-4208 MP1 interlock Switch Assembly *277-3990 PC Photocell, Night *77-3258 PC1 Photocell, Night w/socket *77-3258PCA R1 Power Resistor, 10kohm, 55Watt *77-3959 R2-4 Power Resistor, 20ohm, 40Watt *77-2759 S1 interlock Switch *77-2644 SLM1 Sidelight Control Module (w/terminal block) *277-4195 SM1 Sync Monitor Board *277-4163 T1 Power Transformer, 120/240V 60Hz *77-3970C T1 Power Transformer, 240/480V 60Hz *77-4137C T1 Power Transformer, 240/480V 50Hz *77-4138C T2 current Sense Transformer 40000679-001 Product # Description PART # C1 capacitor, Resonating, 4uF C ca505b661cdg C3 capacitor, Night, 5uF *77-3911 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure, FG2000B/3000B 40000678-004 F1/F3 Input Power Fuse, 6Amp *77-1167 HV high Voltage Board *277-3937 K1-2 Interlock & Day/Night Relay *77-2013 K4 Sidelight Power Relay KA121AV0522C MB1 Mother Board *277-5016-001 PC Photocell *77-3259 PC1 Photocell w/socket *77-3259PCA PS1 FlashGuard 2009B Power Supply, 120V 60Hz 40000681-027 PS2 FG2009B Power Supply, 120V No Sidelight 40000681-028 R1 Power Resistor, 50ohm, 55Watt RW50RB0500GF R2-4 Power Resistor, 20ohm, 40Watt *77-2759 R5 Power Resistor, 1.5kohm, 50Watt 40000683-001 R6-7 Power Resistor, 50kohm, 50Watt RW50RB0502GF S1 interlock Switch *77-2644 S2 interlock Switch Assembly 40000677-001 SLM1 Sidelight Control Module B b7c23paa SM1 Sync Monitor Board *277-4163 T1 Power Transformer, 120/240V 60Hz *77-5002 T2 current Sense Transformer 40000679-001 TC1 trigger Control Board *277-5014-003 TF1 transformer Fuse, 630mA *DP-1019 TB2 terminal Block Assembly *77-3965 TC1 trigger Control Board *277-4169 TF1 transformer Fuse, 630mA *DP-1019 877.285.4466 Toll Free 47

DIAGRAMS FG3000 FG3000B Product # Description PART # C1 capacitor, Resonating, 3uF *77-3311 C2 capacitor, Day, 40uF *77-3949 C3 capacitor, Night, 7uF *77-3982 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure *77-4219 F1 input Power Fuse, 10Amp *77-2040 F3 Sidelight Fuse, 4Amp *DP-1020 HV high Voltage Board *277-3937 K1-2 Interlock & Day/Night Relay *77-2013 K4 Sidelight Module Sensor *77-4196 K5 Sidelight Module Power Relay *77-4198 MB1 Mother Board *277-4208 MP1 interlock Switch Assembly *277-3990 PC Photocell *77-3259 PC1 Photocell w/socket *77-3259PCA R1 Power Resistor, 10kohm, 55Watt *77-3959 R2-4 Power Resistor, 20ohm, 40Watt *77-2759 S1 interlock Switch *77-2644 SLM1 Sidelight Control Module (w/terminal block) *277-4195 SM1 Sync Monitor Board *277-4163 T1 Power Transformer, 120/240V 60Hz *77-3970C T1 Power Transformer, 240/480V 60Hz *77-4137C T1 Power Transformer, 240/480V 50Hz *77-4138C T2 current Sense Transformer 40000679-001 TB2 terminal Block Assembly *77-3965 TC1 trigger Control Board *277-4169 TF1 transformer Fuse, 630mA *DP-1019 Product # Description PART # C1 capacitor, Resonating, 5uF C ca505b661cdg C2 Capacitor, Day, 70uf CA706A441EK C3 capacitor, Night, 4uF *77-3911 DB1 Diode Board *277-3939 E1 Stainless Steel Enclosure, FG2000B/3000B 40000678-004 F1/F3 Input Power Fuse, 6Amp *77-1167 HV high Voltage Board *277-3937 K1-2 Interlock & Day/Night Relay *77-2013 K3 Trigger Transformer Relay KA025DC10S2N K4 Sidelight Power Relay KA121AV0522C MB1 Mother Board *277-5016-001 PC Photocell *77-3259 PC1 Photocell w/socket *77-3259PCA PS1 FlashGuard 3000B Power Supply, 120V 60Hz 40000681-033 R1 Power Resistor, 50ohm, 55Watt RW50RB0500GF R2-4 Power Resistor, 20ohm, 40Watt *77-2759 R5 Power Resistor, 1.5kohm, 50Watt RW000002 R6-7 Power Resistor, 50kohm, 50Watt RW50RB0502GF S1 interlock Switch *77-2644 S2 Interlock Switch Assembly 40000677-001 SLM1 Sidelight Control Module B b7c23paa SLM1 Sidelight Control Module, LED B b7c23laa-001 SM1 Sync Monitor Board *277-4163 T1 Power Transformer, 120/240V 60Hz *77-5002 T1 Power Transformer, 240/480V 60Hz *77-5066 T1 Power Transformer, 240/480V 50Hz *77-5067 T2 current Sense Transformer 40000679-001 TC1 trigger Control Board *277-5014-003 TF1 transformer Fuse, 630mA *DP-1019 48 HUGHEYANDPHILLIPS.COM

DIAGRAMS SS-125 SS-122 Product # Description PART # A1 high Voltage Supply Board *277-3261 A2 trigger Control Board *277-3262 A3 Fault Monitor Board *277-3263 C1 capacitor, 1uF, 1700V *77-4220 C2 capacitor, 12.5uF, 2500V *77-4108 C3 capacitor, 110uF, 2500V *77-4133-001 C4 capacitor, 3uF, 2500V *77-3311 DB1 Diode Block *277-3342-6 DS1 interlock Assembly (w/ S1-S3) *77-3323 E1 Stainless Steel Enclosure, SS-125 *77-3296-02 F1 Fuse, SB, 3.2A 480V System *77-2041 F1 Fuse, SB, 6A 240V System *77-1167 F1 Fuse, SB, 10A 120V System *77-2040 F2-F5 Fuse, SB, 1A, 3AG *77-2365 FT Flashtube Assembly *77-3295 FTS Flashtube Assembly with sockets *77-3295S K1 Interlock Relay *77-2878 Product # Description PART # MB Mother Board, SS-122 *277-3047 A1 Sync & Timing Board *277-2673 A2 Digital Monitor Board, 1-8 Lights *277-2536 A3 Digital Monitor Board, 9-16 Lights *277-2537 A4 Digital Monitor Board, 17-24 Lights *277-2538 K4-K5 Relay *77-2710 K1-3, K6-K7 Relay, 3PDT *77-3041 T1 Logic Transformer *277-2214 T2 Power Transformer, 240/480V, 50/60Hz *77-2549 T2 Power Transformer, 120/240V, 50/60Hz *77-3886 T2 Power Transformer, 208/220V, 50/60Hz *77-3144 F1 Fuse, SB, 10A *77-2040 SS-124 Photocell Assembly PCELL Photocell Assembly, SS-124 *277-3247 PR Photocell Receptacle *77-3257 PN Photocell, Night *77-3259 PT Photocell, Twilight *77-3258 K2-K4 Mode Relays *77-2013 LA Surge Arrestor *77-4139 MB Mother Board *277-3264 R1-R6 Resistor Block Assembly *277-3546 RA Reflector Assembly *277-3898 S1 interlock Switch *77-2644 S2 Remote/Local Switch *77-2668 S3 Mode Switch (Day, Twilight, Night) *77-2667 T1 input Transformer, 60Hz *77-3890 T1 input Transformer, 50Hz *77-4244 T1-SB T1 Voltage Selector Block, 120V *77-3319 T1-SB T1 Voltage Selector Block, 240V *77-3321 T1-SB T1 Voltage Selector Block, 480V *77-3322 T2 trigger Transformer Assembly *277-3324 WH Wire Harness Assembly *77-3355A 877.285.4466 Toll Free 49

DIAGRAMS KG114F0001 LC-5000 Product # Description PART # DL Dome Lens, red, beacon SFL150 UL upper Lens, red, beacon SFL125 LL Lower Lens, red, beacon (x2) SFL100 EB Eyebolt Assembly 6A0002SAY WS Wire Set Assembly A6A0001WA UR upper Beacon Rods (x3) B b6a0002af2 LR Lower Beacon Rods (x3) A6A0002AG GS gasket Set (9 total) A6A0002AR WT Watertight Connector, 1 WT4A037050TT CB cable Assembly, #12-3C, 12 Feet A6A0001WC12 Product # Description PART # MB-1 Micro-Controller board, A-0 40000444-001 MB-2 Micro-Controller board, A-1 40000444-002 MB-3 Micro-Controller board, A-2/3 40000444-003 K1-K4 Solid State Relay, 50A, NC KM121AV50D2D F1 0.1A 250V Slo-Blo Fuse 40000408-001 F2-F5 12A 250V Slo-Blo Fuse 40000409-001 F6 1A 250V Slo-Blo Fuse *77-2365 F7, F8 5A 250V Slo-Blo Fuse 40000410-001 F9-F11 12A 250V Slo-Blo Fuse 40000409-001 PCELL Photocell, 120V, Night *77-3258 LH Lamp, beacon, 620 Watt, 120VAC LH620120GE LH Lamp, beacon, 700 Watt, 230VAC LH700230HDT SK Socket, lamp, mogol, CSA, 2500W 240V XLFC5S300 SK Socket, lamp, mogol, 2500W 240V XL000001 50 HUGHEYANDPHILLIPS.COM

DIAGRAMS OB20 SERIES MBC2161B45S TO PHOTOCELL SIDELIGHT FAILURE BEACON FAILURE FLASHER FAILURE LIGHTS ON POWER FAILURE COMMON Product # Description PART # CC L-810 Casting Cover, painted, double c6a0008ab2 CL Sidelight Latch Spring A6A0008AJ CS L-810 Casting, painted, single, bottom hub 15H00600-1 CS L-810 Casting, painted, single, side hub C6A0005AA21 CS L-810 Casting, painted, double, bottom hub C6A0008AA21 CS L-810 Casting, painted, double, side hub C6A0022AA21 GS gasket, neoprene A6A0008AG LH Lens Holder Assembly with 7 chain B6A0008AA LP Lamp, 116W, 120V LH116120GE LP Lamp, 116W, 230V LH116230DT LS Lens, Red, fresnel, L-810 FL02B02810 LS Lens, Clear FL0CB02810 LS Lens, Yellow FL04B02810 LS Lens, Green (when lit) FL08B02810 LS Lens, Blue (when lit) FL06B02861T Product # Description PART # FB Fuse, Beacon, 15A FUKTK150601 FR Fuse, Load Balance Resistor, 7A FUFNM70G251 FS Fuse, Sidelight, 5A FUFNM50G251 K2 Power Relay, Solid State, 30A, 120V KR241AV120NC K5 Flasher By-Pass Relay Assembly A6C0015AG KZ Beacon Flasher Assembly KZ1L1RR30A MB Mother Board D6C0015AB01 PC Photocell Assembly PA446F21BS PI-PECB Photo Control Board B b6p0004ad WH Wire Harness 6C0015AH TB1-E Terminal Block End tbe230aa TB1-S Terminal Block Section tbs213aa01a TB2-E Terminal Block End tbe330aa TB2-F Terminal Block Section tbs213aa01a TB2-S Terminal Block, Fusible tbs352aa01a LT Sidelight Latch A6A0008AD PN Sidelight Spring Pin PS07501002D0 PR 1 to ¾ Pipe reducer PR0304B4R SS Lamp socket, porcelain, 660W, 250V XLCB4S2200 TR Transfer relay assembly with relay &sockets 6A0013SK3 TR-R Transfer Relay, 0.3A Coil 13Amp obrl100 877.285.4466 Toll Free 51

Accessories

ACCESSORIES 9LC CONTROL SYSTEM APPLICATION 9LC series lighting controls combine the finest in digital circuitry with rugged electromechanical hardware to yield the industry s most comprehensive obstruction lighting controls. Standard models are available for all common FAA and ICAO applications. The 9LC s modular design allows for custom controls for almost any combination of flashing red beacons and sidelights. All models include a NEMA 4 outdoor housing and a calibrated photocell for automatic day/night switching. A photocell override switch is standard on all systems, facilitation troubleshooting or maintenance. All controls provide comprehensive status indicators and alarm contacts for easy connection to remote monitoring systems. Features Controls for multiple beacons flash all beacons simultaneously per FAA and ICAO specifications Lightning protection provided by: - Circuit breaker protection to all tower lighting circuits - MOV surge suppressors on all inputs, outputs, and photocell lines - Torroidal current sensors isolate tower lines from monitoring circuitry Load balance resistor capability is available Modular design allows customization for nearly any application Dozens of models already developed for control of up to 14 beacons Standard with NEMA 4 enclosures (NEMA 4X optional upgrade) Alarm Contacts / Control Status Individual alarm contacts and control status is provided for: - Control power failure - Day/night mode status - Each flashing red beacon - Each level of steady burning obstruction lights - Flasher by-pass alarm/status for each beacon Number of lamps being monitored can easily changed by setting dip-switches Bi-color red/green LED status indicators provide instant indication of alarm and control status Normally open and normally closed alarm contacts are both available Primary and auxiliary alarm contacts provided Lighting Structure Input VoltagE Sidelight LBR Model # System Type Height (50/60Hz) Beacons Strobes Levels Capability 9LCA001000AA FAA A-0 Incandescent 0-150 120V 0 1 no 9LCA111L00AA FAA A-1 Incandescent 151-350 120V 1 1 Yes 9LCA233L00AA FAA A-2 Incandescent 351-700 120V 3 2 Yes 9LCA354L10AA FAA A-3 Incandescent 701-1050 120V 5 3 Yes 9LCA474L10AA FAA A-4 Incandescent 1051-1400 120V 7 4 Yes 9LCD111000AA FAA D-1 Strobe 200-350 120V 1 no 9LCD231000AA FAA D-2 Strobe 351-500 120V 3 no 9LCE111L0BAA FAA E-1 inc/strobe 200-350 120V 1 1 Yes 9LCE233L0BAA FAA E-2 inc/strobe 351-500 120V 3 3 Yes 9LCIA06000AA ICAO A-0 Incandescent 0-150 230V 1 no 9LCIB16L00AA ICAO A-1 Incandescent 151-350 230V 1 1 Yes 9LCIB26L00AA ICAO A-2 Incandescent 350 700 230V 2 1 Yes 9LCIC16L00AA ICAO A-1 Incandescent 151-350 230V 1 2 Yes 9LCID16L00AA ICAO A-1 Incandescent 151-350 230V 1 3 Yes 9LCR001000AA FAA A-0 LED 0-150 120V 1 no 9LCR111000AA FAA A-1 LED 151-350 120V 1 1 no 9LCR231000AA FAA A-2 LED 351-700 120V 3 2 no 9LCR354000AA FAA A-3 LED 701-1050 120V 5 3 no 54 HUGHEYANDPHILLIPS.COM

ACCESSORIES APPLICATION The LC-5000 series lighting controls combine the finest in digital circuitry with rugged microprocessor based hardware to yield the industry s most comprehensive obstruction lighting controller. The LC-5000 design allows for quick installation. The auto-configure design will evaluate the lighting on the tower and configure itself to operate and monitor installed lighting. All models include a NEMA 4 outdoor housing and a calibrated photocell for automatic day/night switching. A photocell override switch is standard on all systems, facilitation troubleshooting or maintenance. All controls provide comprehensive status indicators and alarm contacts for easy connection to remote monitoring systems. LC-5000 Red Lighting Controller Features Controls for multiple beacons flash all beacons simultaneously per FAA and ICAO specifications Lightning protection provided by: Circuit breaker protection to all tower lighting circuits MOV surge suppressors on all inputs, outputs, and photocell lines Torroidal current sensors isolate tower lines from monitoring circuitry Diagnostic LED Tree provides instant verification of beacons and sidelights Modular design allows customization for nearly any application Dozens of models already developed for control of up to 14 beacons Standard with NEMA 4 enclosures (NEMA 4X optional upgrade) Alarm Contacts / Control Status Bi-color red/green LED status indicators provide instant indication of alarm and control status Normally open and normally closed alarm contacts are both available Primary and auxiliary alarm contacts provided dimensional diagrams SIDE VIEW FRONT VIEW Environmental Temperature -55 C to +55 C, -67 F to + 130 F Humidity 95% relative humidity Will withstand exposure to: Wind-blown rain from any angle Wind speed of 240kph (150mph) NEMA Rating NEMA 4 Weight 10 lbs. model Numbers system type input voltage LC5000-001 Incandescent or LED A-O 120V or 240V LC5000-002 Incandescent or LED A-O or A-1 120V or 240V LC5000-003 Incandescent or LED A-O or A-1 or A-2 120V or 240V 877.285.4466 Toll Free 55

ACCESSORIES Lightning Surge Protection Device - LSPD-3000B APPLICATION LSPD devices are designed to protect all the FlashGuard TM medium intensity strobe lighting systems. The LSPD provides both a grounding solution and surge suppression for these installations. The LSPD minimizes exposure to lightning damage through tower light wiring, a lightning path that is commonly overlooked at communications sites. Without the use of a LSPD, the interconnecting cable between the strobe s flashhead and the power supply provides a direct path that can allow damaging surges and transients to enter the shelter. Sites with LSPDs installed have proven reliability. Sites with previous lightning problems have recorded hundreds of lightning strikes after LSPD installation, with no damage to the power supply or communication equipment. Installation LSPD units are installed between the flashhead and the power supply, providing protection for both the lighting power supply and the telecommunications equipment installed at the site. The LSPD units are supplied in a fiberglass NEMA 4X outdoor enclosure. The protectors should be mounted on the tower above the ice bridge, before the cable turns to enter the shelter. The first level of protection forces any induced voltage on the cable s shield to tower ground. All lines then pass through a surge suppression device before continuing to the power supply. Detailed installation instructions are included with each unit and should be adhered to for optimum protection. FAA Type: L-864 Medium Intensity Lighting ICAO Type: Medium Intensity Type B (L-864) Compliant to: Canadian Aviation Regulation (CAR) 621.19 DGAC of Mexico ICAO Annex 14, CAR 621.19 Specifications: Response Time Current Withstand Circuitry Less than 5 µs. 40 ka per mode; IEEE C62.41 8x20µs short circuit waveform the LSPD is series wired with parallel protection. Robust MOVs protect all circuits. Large ground plane bonded to a #2 copper ground lug provides a strong electrical/ mechanical discharge point. SERIES 800 PhotoController & Beacon Flasher application The Hughey & Phillips SERIES 800 PhotoController and Beacon Flasher provides a low cost, high reliability solution to your lighting needs. This unalarmed system allows for the user to add an inline system to their conduit run on the tower to controller the installed FAA beacons and sidelights. The systems are factory calibrated and never need adjustment. Each system utilizes surge and transient components and additional input line protection. Normally closed solid state relay configuration assures Lights ON condition even if the circuitry fails. Red LED provides quick visual verification of field operation. And with its modular design, it allows for quick field installation or retrofit to existing system if ever damaged. model Numbers S800PC120 S800PC240 S800BF120 S800BF240 Description Photo Controller, 120VAC Photo Controller, 240VAC Beacon Flasher, 120VAC Beacon Flasher, 240VAC Spare Parts Hughey & Phillips is the OEM for all your needs Flashtubes Cables Wire Harnesses Junction Boxes Lamps Relays Capacitors Lightning Rods Transformers Ice Shields Brackets 56 HUGHEYANDPHILLIPS.COM

ACCESSORIES APPLICATION Combining technology with ease-of-use, Hughey & Phillips third-generation GPS unit combines flash synchronization and day-night sensing, and can be installed with just one plug-in cable. This eliminates the need to mount a separate GPS unit, antenna, junction box and wiring. Reliable, glitch-free operation is assured, using a crystal and the 50/60Hz power line as a zero-drift timing reference if the satellite signal is momentarily lost. And two different flash modes are provided: fixed 40FPM or bit-switch selectable 24, 30, 40 or 60 FPM. The unit easily mounts with four screws to any surface, or pole mount using the optional bracket. Installation interconnect cable with quick connect plugs from GPS unit to controller unit. LEDs indicate Power, Sync and GPS Lock status. With rugged metal weatherproof and a battery-free design, Hughey & Phillips GPS unit will provide years of reliable service for your wind farm. GPS SYNC / Photocell Module FAA Advisory Circular AC 150/5345-43F Canadian Aviation Regulation 621.19 ICAO Annex 14, MIL-C-7989, DGAC of Mexico Specifications Specifications Input Voltage 100-132VAC 50/60Hz, 10W max. External Dimensions 6-1/4 x 6-1/4 x 4-1/8 Enclosure NEMA 4 Painted Aluminum Mounting Dimensions 5-1/8 x 6-3/4 Operation Temperature -40 to +55 C (4) #8 Holes Indicators Power (Green) GPS Lock (Yellow) Optional Mounting 1-1/4 to 2-3/4 Pole SYNC (Flashing Red) bracket SYNC Output 15-27VDC, 100mA, 3ms pulse SYNC Adjustments Day: 40FPM night: 24, 30, 40, 60 FPM Backup SYnc internal Crystal Clock or AC Line Part NumbERS Part Numbers 40002075-001 gps SYNC Module 40002074-003 gps Cable, 100 *77-3259 Photocell, 120V, 35-60 ft-cd 40002074-004 gps Cable, 150 40002074-001 gps Cable, 25 40002074-005 gps Cable, 350 40002074-002 GPS Cable, 50 40002082-001 Pole Mounting Kit 877.285.4466 Toll Free 57

ACCESSORIES Lightning Rod Assembly Mounting Bracket for Dual Lighting Part # KG 0926M001 MOUNTING RING LIGHTNING ROD JAM NUT BEACON Application The Lightning Rod Assembly, LRB58L7510M, is designed for, and is widely used on antenna towers associated with microwave relay installations, high-definition broadcast towers, and other structures prone to lightning strikes. Consisting of a 7/8 diameter rod and a base mounting ring designed for ready installation under existing medium intensity lighting fixtures with a 13-1/4 bolt hole pattern. The A6A0302AB Lightning Rod extends approximately two feet above a standard 300mm code beacon in order to reduce the probability that lightning will strike the lighting fixture. This will minimize the possibility of damage to the lighting fixture and the wiring from cloud to ground lightning strikes STROBE TOWER DOUBLE BEACON/ STROBE Ease of Installation The base mounting ring is designed for installation underneath the base of a medium intensity lighting fixture with a 13-1/4 bolt hole pattern without requiring additional holes in the tower. It is only necessary to remove two of the four mounting bolts in order to install the ring under the existing fixture. The other two beacon mounting bolts must be loosened sufficiently to enable the installer to slide the lightning rod mounting ring under the fixture. Slotted holes are provided in the base mounting ring in order that the ring may be rotated to avoid interference with the tower bolts or details. The mounting ring should be positioned so that the rod is located at either side of the fixture in order to avoid interference during opening of the fixture for maintenance. General The base mounting ring is an aluminum casting, tapped to accept the threaded rod. The rod is fabricated from 7/8 diameter material threaded at one end for insertion into the mounting ring. The rod is specially treated after fabrication to withstand weathering Part Numbers: BEACON/STROBE MOUNTING BRACKET Mounting bracket will accommodate vertical tower members from 1.5 to 4.5 in diameter. Standard U bolts are used to secure the bracket to the tower. SUPPORT ANGLE TOWER LEG U BOLTS Strobe Mounting Bracket For: 1. Model KG114 - Red Beacon 2. Model KG225 - Strobe 3. Model FG2000 - Strobe 4. Model FG3000 - Strobe Material: galvanized steel BEACON/STROBE ICE SHIELD ASSEMBLY To mount beacon or strobe to the bracket, use H&P mounting assembly Part Number A6A0001SE EXPANDED METAL PARTIALLY OMMITTED FOR CLARITY OR ILLUSTRATION LRB58L7510M A6A0302A13 A6A0302AA2 NH7510CB2 Lightning Rod Assembly Lightning Rod Mounting Ring Jam Nut SUPPORT ANGLE SECURING BRACKET 58 HUGHEYANDPHILLIPS.COM

ACCESSORIES Load Balance Resistor LB112120 120V, 1200W Application The proper operation of electrical and electronic devices in general is based on the availability of a relatively steady line voltage. This condition is usually met without special precaution when the several connected loads all consume a steady amount of power. If one or more of the loads are of a varying or pulsating nature, then the degree of steadiness of the line voltage (i.e. line voltage regulation) will be dependent upon several factors such as: The voltage regulation of the power service to the installation (i.e. is the power service a firm-heavy source with adequate capacity or a soft source at the end of a rural line). The size of the conductors between the power service and the connected load. In many cases the size is not adequate for the load, thus causing a large voltage drop. The size and voltage regulation of the standby generator. The relative size of the pulsating load as related to the total connected load at site. Also of prime importance is the relative sensitivity of the electronic or radio equipment to the variations in the line voltage. The rules of the FCC and FAA require the 300mm Beacon to flash ON and OFF at a rate between 20 and 40 flashes per minute. The beacon normally uses two 620 watt lamps, thus a pulsating load of 1240 watts. Assuming a rate of 30 FPM, the 1240 watt load is ON for 1-1/3 seconds and OFF for 2/3 seconds. Due to some inrush current when the lamps are ON, the effect on the line voltage may be slightly more severe than flashing a resistive load of 1240 watts. In some installations, the 1240 watt pulsating load may represent a substantial portion of the total connected load. In these cases the variations in the line voltage may be quite severe and some corrective means must be considered. Fortunately, a relatively simple and quite effective corrective means is available a Load Balance Resistor. This consists of a 1200 watt resistive load which is switched ON as the Beacon load is switched OFF and vice versa. The Hughey and Phillips LB112120 and LB212480 Load Balance Resistors (LBR) are designed for use with flashing Beacons and will minimize fluctuations in the beacon lighting load circuit, when used is conjunction with our 9LC Lighting Controls. Housed in a louvered galvanized steel case, the LBR is suitable for outdoor installations. The mounting brackets are movable in order to provide for mounting against a vertical or horizontal surface. Connection to the LBR is made to a terminal strip mounted in a watertight cast junction box which is tapped for ½ conduit or conduit fitting. The resistive elements are of the strip type to provide uniform heat distribution and are of steel-sheath construction with compressed insulation. SiteGuard WC-60 Wireless Monitoring Hughey & Phillips Digital Cellular Communicators deliver secure, reliable and complementary digital communications via the GSM (Global System for Mobile) network. This groundbreaking communications solution offers full data reporting and uploading/downloading with most Hughey & Phillips control panels. In addition, with onboard zone inputs and optional dialer capture capability, we re compatible with other manufacturers security panels as well. All signals are delivered to the AlarmNet Network Control Center, which routes the information to the appropriate central station. The state-of-the-art AlarmNet Network Control Center is fully redundant and monitored 24/7. AlarmNet has the ability to route messages using AlarmNet-i and 800 PLUS services, providing true redundancy and multi-path message delivery. SiteGuard monitoring services handles all of the time dependent monitoring tasks without requiring your interaction: if a light burns out, Hughey & Phillips s system does the following: Dry contact output is read into the SiteGuard System SiteGuard initiates alarm call over a GSM wireless connection Alarm received at ProtectionNet Network operations center, with operators providing around the clock, 365 days a year service ProtectionNet initiates an FAA Notice to Airmen (NOTAM) for any appropriate lighting failure The client is notified of the failure via telephone, voicemail, pager, fax or e-mail With the NOTAM in place, you can now work at your own schedule to repair the light outage If after 14 days we have not heard from you, we will contact you to determine the status of your tower We will file the NOTAM extension if necessary or we will remove the NOTAM, with no additional work from you Part Numbers: OBMISC215 Digital Cellular Communicator (SiteGuard WC-60) OBMISC236 GSM Antenna, outdoor, GSM-ANT3DB, omni-directional SMISC234 GSM Adapter Cable, WA7626-CA SMA to N Adapter MC000017 GSM Coaxil Cable, 25 Wind Turbine Switch The Hughey & Phillips Wind Turbine Switch (WTS) is designed to operate the required obstruction lighting from either the high voltage generated by the wind turbine within the nacelle or from the commercial power supplied at the base of the tower. Utilizing patent-pending technology, the WTS senses the highest voltage present and powers the obstruction lighting at either 120VAC or 230VAC. The WTS harnesses the power of wind to power your obstruction lighting requirements. 877.285.4466 Toll Free 59

ACCESSORIES junction boxes Weathertight Cast Aluminum for Surface Mounting General Information Hughey & Phillips Weathertight Junction Boxes are of cast aluminum. Each box is of adequate size for the number of terminals to enable proper and simplified installation. All boxes are furnished complete with cover, gasket, cover retaining chain and self-retaining type cover screws. Tapping - Hughey & Phillips Weathertight Junction Boxes are available with or without tapped conduit hubs. In ordering, specify size. Terminals - Hughey & Phillips Weathertight Junction Boxes are available with standard screw type terminal blocks, or special blocks with split connectors, or combinations, to customer order. The terminal capacity indicated under each type of box is representative of one type terminal block all terminal strips are insulated. Insulated Cable Supports - Hughey & Phillips Weathertight Junction Boxes are available with built-in cable support (with or without terminals) to meet requirements of the National Electric Code. Insulated Bushing - Hughey & Phillips will install, when specified, plastic insulating bushings inside of tapped conduit hubs. Junction Box No. JB00000000 Junction Box No. JC00000000 Description Cast aluminum, watertight, complete with cover and screws, gasket, and cover retaining chain. Available with or without terminal block, and/or cable support. Specifications Inside Dim. (Approx.) 5 3/8 Dia. 2 5/8 Depth Capacity 5 Term. (Kulka No. 603-5) 7 Term. (Buchanan Type HD) Max. Hub Tap 1 Cond. Size Description Cast aluminum, watertight, complete with cover and screws, gasket, and cover retaining chain. Available with or without terminal block, and/or cable support. Specifications Inside Dim. (Approx.) L 4 7 / 8, W 7, D 4 Capacity 8 Term. (Kulka No. 603-8) 10 Term. (Buchanan Type HD) Max. Hub Tap 1 Cond. Size 60 HUGHEYANDPHILLIPS.COM

ACCESSORIES junction boxes Weathertight Cast Aluminum for Surface Mounting Junction Box No. JF00000000 Junction Box No. JG00000000 Description Cast aluminum, watertight, complete with cover, cover screws, gasket, and cover retaining chain. Available with or without terminal blocks, and/or cable support, screw-cap receptacles, etc. Furnished with mounting bars or mounting clamps, if specified on order. Specifications Inside Dim. (Approx.) L 10, W 9, D 5 Capacity 20 Term. (2-Kulka No. 603-10) 24 Term. (Buchanan Type HD) **Max. Hub Tap Sides (R, L**) 1 Top & Bottom (T, B**) 2 Cond. Size Description Cast aluminum, watertight, complete with cover, cover screws, gasket, and cover retaining chain. Available with or without terminal blocks, and/or cable support, screw-cap receptacles, etc. Furnished with mounting bars or mounting clamps, if specified on order. Specifications Inside Dim. (Approx.) L 15, W 9, D 5 Capacity 30 Term. (3-Kulka No. 603-10) 36 Term. (Buchanan Type HD) **Max. Hub Tap Sides (R, L**) 1 Top & Bottom (T, B**) 2 Cond. Size *Order junction boxes by number, and specify hub tapping**, number & type of terminals, & with or without...cable support, insulating bushings, receptacles, mounting rails, etc. *Maximum hub taps indicated are for standard boxes. Larger hub size and taps available on special order. Method of Specifying Conduit Hub Taps conduit size symbols Conduit Size 1 /2 3 /4 1 1 1 /4 1 1 /2 2 Ordering Symbol 2 3 4 5 6 7 Conduit Hub Tap Location Symbols XX TRBL X 00 XX (Type (Taps) (Cable (# of Term Box) Support Pos B block) optional) Example: Cat. No. JC Type Box to be topped 1 1 /4 top and bottom and 3 /4 left side only. Order As: Junction Box Cat. No JC5053C03B 877.285.4466 Toll Free 61

ACCESSORIES K-Z Series Beacon Flasher Conforms to FAA and FCC specification. Completely calibrated to applicable FAA/FCC specifications by factory technicians. No field adjustment ever necessary. Ultra reliable: surge and transient resistance components. High power: rating 2.0KW maximum continuous tungsten load at up to 131 F (+55 C) ambient air temperature 120 or 240 VAC option per circuit. Flash rate: 30 FPM; 2/3 on, 1/3 off duty cycle. Fail safe operation: normally closed solid state relay configuration assures lights on condition even if control circuitry fails. Visible operation indicator red LED (light emitting diode) provides instant visual verification of field operation. Modular construction: Easy field installation or retrofit for existing applications. Easy replacement if damaged. Specifications Input Voltage: 120 VAC 1 0 / 240 VAC 1 0 Power Rating: 2000 Watts maximum, continuous duty (zero voltage switching) Flash rate: 30 FPM; 2/3 on, 1/3 off duty cycle Peak Current Surge: 320 Amps 100 milliseconds, 650 amps, 1 cycle @ 60 Hz (non repetitive) Operating Temperature: -55 C to +55 C Transient Suppression: 2.5 KV@ 10 milliseconds components to case Reliability: MTBF over 500,000 hrs (SSR) per MIL-217C List of Standard Solid State Beacon Flashers Part Number Description KZ1L10R30A 1-Beacon 120V KZ2L10R30A 1-Beacon 240V KZ1L1RR30A 1-Beacon & Load Balance Resistor 120V KZ2L1RR30A 1-Beacon & Load Balance Resistor 240V KZ1L20E30A 2-Beacon Simultaneous 120V KZ2L20R30A 2-Beacon Simultaneous 240V KZ1L2PR30A 2-Beacon Alternate 120V KZ2L2PR30A 2-Beacon Alternate 240V KZ1L2SR30A 2-Beacon & 2 Load Balance Resistor Simultaneous 120V KZ2L2SR30A 2-Beacon & 2 Load Balance Resistor Simultaneous 240V KZ1L2QR30A 2-Beacon & 2 Load Balance Resistor Alternate 120V KZ2L2QR30A 2-Beacon & 2 Load Balance Resistor Alternate 240V KZ1S3T030BA 3-Beacon Simultaneous 120V KZ3S3T030B 3-Beacon Simultaneous 240V KZ1S3T030A 3-Beacon Sequential 120/208V KZ2L4N03BA 4-Beacon Simultaneous 240V KZ1L4NR30A 4-Beacon 2+2 180 Apart 120V KZ1S4N030AA 4-Beacon Sequential 120/208V KZ1S5N030AA 5-Beacon Sequential 120/208V KZ1S5N030A 5-Beacon 4 Position 120/208V (2 Beacon Top) KZ1S6N030AAB 6-Beacon 4 Position 120/208 V (3 Beacon Top) KZ1S7Z030B 7-Beacon 120/208 V (Top & Bottom Flash Together) KZ1S7U030A 7-Beacon 5 Position 3 Beacon Top 120/208V 62 HUGHEYANDPHILLIPS.COM

lighting systems

LIGHTING SYSTEMS 64 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS 877.285.4466 Toll Free 65

LIGHTING SYSTEMS 66 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS 877.285.4466 Toll Free 67

LIGHTING SYSTEMS 68 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS r e pa i r s e r v i c e s a g lo b a l l e a d e r Hughey & Phillips is a global leader in the design and manufacturing of obstruction lighting technology. We engineer and design a complete line of low, medium and high intensity lighting technology solutions for radio, television, and communication towers; wind turbines; buildings; smokestacks; bridges; and other obstructions to aerial navigation. All products are Hughey & Phillips offers a vast selection repair services for tower lighting controllers, flashheads and beacons. Our repair service department offers customers a fast and economical method to overhaul their fielded equipment for years of operation. manufactured by Hughey & Phillips in the USA. With a full engineering staff providing complete support and design in optical, electrical and mechanical disciplines to customize any of our products to fit our customers unique needs. To learn more, visit www.hugheyandphillips.com 877.285.4466 Toll Free 69

LIGHTING SYSTEMS 70 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS 877.285.4466 Toll Free 71

LIGHTING SYSTEMS 72 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS 877.285.4466 Toll Free 73

LIGHTING SYSTEMS 74 HUGHEYANDPHILLIPS.COM

LIGHTING SYSTEMS 877.285.4466 Toll Free 75

faa standards

faa standards Red Obstruction Lighting Standards (FAA Style A) Day Protection = Aviation Orange / White Paint Night Protection = 2,000cd Red Beacon and sidelights 1751-2100 1401-1750 = L-864 flashing beacon 1051-1400 = L-810 obstruction light 701-1050 351-700 151-350 0-150 a-0 a-1 a-2 a-3 a-4 a-5 a-6 Notes: 1. The overall height of the structure including all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. 2. The red obstruction lighting system is composed of flashing omnidirectional beacons (L-864) and/or steady burning (L-810) lights. When one or more levels is comprised of flashing beacon lighting, the lights should flash simultaneously. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 5, and 12. 78 HUGHEYANDPHILLIPS.COM

faa standards High Intensity Obstruction Lighting Standards (FAA Style B) Day Protection = 200,000cd White Strobe Twilight Protection = 20,000cd White Strobe Night Protection = 2,000cd White Strobe 1751-2100 1401-1750 1051-1400 701-1050 351-700 = L-856 high intensity strobe (3 flashheads required per level for 360 o coverage) B-2 B-3 B-4 B-5 B-6 Notes: 1. The height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting, consisting of a Medium Intensity L-865 White Strobe, see FAA Style C. 2. When high intensity white lights are operated 24 hours a day, other methods of marking and lighting may be omitted. This system should not be recommended on structures 500 feet (153 meters) AGL or less unless an FAA aeronautical study shows otherwise. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 7, and 12. 877.285.4466 Toll Free 79

faa standards High Intensity Obstruction Lighting Standards (FAA Style C) Day Protection = 200,000cd White Strobe Twilight Protection = 20,000cd White Strobe Night Protection = 2,000cd White Strobe 1751-2100 1401-1750 1051-1400 701-1050 501-700 = L-856 high intensity strobe (3 flashheads required per level for 360 o coverage) = L-865 medium intensity strobe required appurtenances of 40 feet or greater c-2 c-3 c-4 c-5 c-6 Notes: 1. The height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting, consisting of a Medium Intensity L-865 White Strobe. 2. When high intensity white lights are operated 24 hours a day, other methods of marking and lighting may be omitted. This system should not be recommended on structures 500 feet (153 meters) AGL or less unless an FAA aeronautical study shows otherwise. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 7, and 12. 80 HUGHEYANDPHILLIPS.COM

faa standards Medium Intensity White Obstruction Lighting Standards (FAA Style D) Day/Twilight Protection = 20,000cd White Strobe Night Protection = 2,000cd White Strobe Painting of tower is typically not required 351-500 = L-865 FLASHING WHITE STROBE 1/2 but not lower than 200 feet (61m) 200-350 D-1 D-2 Notes: 1. The overall height of the structure including all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. 2. The medium intensity flashing white light system is normally composed of flashing omnidirectional lights. This system is not normally recommended on structures less than 200 feet AGL. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 6, and 12. 877.285.4466 Toll Free 81

faa standards Medium Intensity Dual Obstruction Lighting Standards (FAA Style E) Day/Twilight Protection = 20,000cd White Strobe Night Protection = 2,000cd Red Strobe and Sidelights Painting of tower is typically not required 351-500 = L-864/L-865 flashing dual (white/red) strobe = L-810 obstruction light 1/2 but not lower than 200 feet (61m) 200-350 e-1 e-2 Notes: 1. The overall height of the structure including all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. 2. The dual lighting system includes red lights (L-864) for nighttime and medium intensity flashing white lights (L-865) for daytime and twilight use. This lighting system may be used in lieu of operating a medium intensity flashing white lighting system at night. Some populated areas where the use of white medium intensity at night may cause significant environmental concerns, the use of the dual lighting system should reduce/mitigate those concerns. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 8, and 12. 82 HUGHEYANDPHILLIPS.COM

faa standards Dual High Intensity Obstruction Lighting Standards (FAA Style F) Day Protection = 200,000cd White Strobe Twilight Protection = 20,000cd White Strobe Night Protection = 2,000cd Red Beacon and Sidelights 1751-2100 1401-1750 1051-1400 701-1050 501-700 = L-856 high intensity strobe (3 flashheads required per level for 360 o coverage) = L-864 flashing red beacon = L-810 red obstruction light f-2 F-3 f-4 F-5 F-6 Notes: 1. The height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting, consisting of a Medium Intensity L-865 White Strobe and a L-864 Red Beacon. 2. This dual lighting system includes red light (L-864) for nighttime and high intensity flashing lights (L-856) for daytime and twilight use. This lighting system may be used in lieu of operating a high intensity flashing white lighting system at night. There may be some populated areas where the use of high intensity lighting may cause significant environmental concerns. The use of the dual lighting system should reduce/mitigate those concerns. 3. The chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory Circular 70/7460-1; Chapters 3, 4, 9, and 12. 877.285.4466 Toll Free 83

faa standards Bridge and Wind Turbine Lighting L-864 or L-865 or (L-864 / L-865) Front View side View 84 HUGHEYANDPHILLIPS.COM

notes 877.285.4466 Toll Free 85

notes 86 HUGHEYANDPHILLIPS.COM

notes 877.285.4466 Toll Free 87

Broadcast Telecommunications Wind Turbines Tall Structures Utilities ABOUT OUR COMPANY Hughey & Phillips is a leader in the design and manufacturing of obstruction lighting technology. We produce a complete line of lighting solutions that provide illumination for aerial navigation around the world. And we offer complete power and lighting systems designed and manufactured in the USA. Our cost-effective obstruction lighting technology provides highly efficient and reliable lighting solutions. By offering complete support and design in electrical, optical and mechanical disciplines, Hughey & Phillips can fully customize any product to fit the unique needs of any customer. 877.285.4466 Toll Free 937.652.3500 Telephone 937.652.3508 FAX HUGHEYANDPHILLIPS.COM 240 W. Twain Ave Urbana, OH 43078 The Evolution of a BranD For more than 75 years Hughey & Phillips has earned a reputation for quality, dependability and innovation in obstruction lighting around the globe. 1930 s 1970 s 1970 s 2000 2000 Present