CERAMIC FAN HEATER INSTRUCTION MANUAL MODEL NO.: R-8056 PLEASE READ ALL INSTRUCTIONS BEFORE USING
Type Specification Voltage Frequency Power R-8056 Remote control 220-240V~ 50HZ 2000W IMPORTANT SAFEGUARDS Thank you for buying our product. Please attentively read this before operating the machine. Keep this operation manual for future reference. 1. The unit should be hung on the wall and make the wind outlet down or laid on level. You must not place it precipitately or tipsily. 2. Please do not use the heater in the place where full of combustible or explosive gas. Don t cover the wind outlet. 3. If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a similarly qualified person in order to avoid a hazard 4. The unit must not be located immediately below a fixed electrical-outlet. The electrical-outlet must be equipped with installment of earth whose capacity should 250V-10A or exceed 250V-10A. The socket and the power plug should be in good connecting condition. 5. If nobody is in or you are repairing the heater, please put off the plug-in 6. Please don t touch the unit by the wet hand or other conductor when it s working.. 7. Motor is out of order, please make it stop immediately. 8. During using the heater, please do not continually open the door or window otherwise it will influence the heating effect. 9.If want to close the machine, press the on/off switch to off, then the machine keep the fan working about 30 seconds until it blowing out
cool wind, then machine will stop working and you can put off the plug-in. 10. Must hang the heater on the wall and fix it away from water in bathroom. 11. Remote control, please use 5# battery, is matched with the unit. If the product needs repair, please ask for special person or our company authorized maintenance department. POSITIONING OF THE APPLIANCE Get two holes on the wall 1.8meters above the floor and near the corner more 20mm, be sure to make the diameter just as same as the expanding pipe. Fix two screws on the expanding pipe, keep the tips of the screws out for 10mm, and hang up the machine after the screws are fixed enough.
OPERATING INSTRUCTIONS 1. The unit was made of high quality plastic shell, firmness and durable. PTC ceramic heater elements, high efficiency heating, noiseless, odor-free, non-polluting, no flame and no need oxygen. 2. Plug into any 220~50 Hz, AC source. Power polity lamp is bright, please use remote control or soft button setting time and power. 3. During using if you feel room temperature is too high/ low, you can press remote control panel + or - to adjust temperature, LED will display room temperature or regulation temperature. 4. Turn the heater on by press the button on control panel, The unit will display the current room temperature, automatic into fan mode, and blow the natural wind. 5. Upon turning the heater button again, the unit will set the heater into low heat mode. 6. Pressing the heater button three times, the unit will set the heater into high heat mode. 7. Pressing the heater button 4th time, the heater will swing. 8. Pressing the heater button once again, switch off the heater. To turn the heater off, Press the heater
button again, cycle operation. Warning: before removing the plug from the socket, switching off and before work for 30-60 seconds for cool down condition that protecting inner parts. TIMER FUNCTION This function will work in any mode. The time function allows you to set the length of operation from 1 hour to 8 hours. Press the time button in the control panel, press one time will increase the length of operation by 1 hour, most 8 hours. OVERHEAT PROTECTION The heater is protected with an overheat protection that switches off the appliance automatically in case of overheat e.g. due to the total or partial obstruction of the grids. In this case, unplug the appliance, wait about 30 minutes for it to cool and remove the object which is obstructing the grids. Then switch it back on as described above. SAFETY CONTROL To avoid damage and danger by overheating, your heater is fitted with super protector that switch as off the heater in the event of overheating until the temperature drops to some extent.
CLEANING AND MAINTENANCE 1. If you don t use the heater for a long time, please wipe the surface and put it into the box. Lay the carton on the ventilated and dry place. Humidity and force press was prohibited. 2. Wait for the machine being cool and pull out the plug, then clean it. Wipe it clean with wet washcloth or cleaner. Never directly wash with water, do not drop the water into the machine. Never clean it with acids, chemical thinner, gasoline, benzene etc. 3. Before use it again, please check it and make sure the outlet ventilation have no any sundries. REMOTE INSTRUCTION MANUAL
Operation steps: Press the button the power will be on, the pilot lamp will be on and cold wind blows out. Press again, the power will be off. FUNCTION You can select 2 powers 1000W/2000W through this button. TIMER press the button setting time,8 display screen.. hours at most, it can be showed by the + and - During using, press + & - controlling temperature. When the room temperature rises to the regulation temperature, heater will stop heating. When room temperature descend lower by 3 than regulation, heating up again. Regulate temperature by + -. Start-up again, first time press + -, the temperature start from 25 ( then change according to last regulation temperature), keeping between 49 and 10. Each press change 1. When pressing + & -, display temperature from the present room temperature switch to regulation temperature. Stopping press key, redisplay the present room temperature.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health, deriving form inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.