Bromic Parts Breakdowns Effective January 1, 2016
PLATINUM GAS 300 & 500 24 21 34 22 27 17 18 19 16 26 20 11 15 23 8 9 13 12 7 12 14 10 14 6 3 7 5 10 1 30 6 4 28 2
PLATINUM GAS 300 & 500 REPLACEMENT PARTS No. Description Part No. 300 Series Part No. 500 Series 1 Glass Retainer - Top BH8080002 BH8080003 2 Glass Retainer - Bottom BH8080004 BH8080005 3 Wind Kicker BH8080006 BH8080007 4 Glass BH8080008 BH8080009 5 Reflector Assembly BH8080018 BH8080019 6 Glass Retainer Side BH8080020 BH8080020 7 Side Shield BH8080021 BH8080021 8 Sail BH8080022 BH8080023 9 Rear Housing BH8080024 BH8080025 10 Rear Housing Mount (Lower) 11 Rear Cover Assembly BH8080026 BH8080027 12 Rear Cover Mount 13 Burner BH8080030 BH8080030 14 Wiring Harness + Ignitor Assembly- Honeywell BH8080010 BH8080011 14 Wiring Harness + Ignitor Assembly- Fenwal 15 Inner Skin BH8080028 BH8080029 16 Wall Bracket Assembly BH8080001 BH8080001 17 Honeywall Control BH8080015 BH8080015 18 Honeywell Gas Valve BH8080014 BH8080014 19 Fenwal Control 20 Dungs 24V Gas Valve 21 WhiteRodger24VGas Valve 22 19mm ID Grommet BH8080033 BH8080033 23 8mm ID Grommet BH8080034 BH8080034 24 Gas Inlet Fitting (1/2 Gas Valve) BH8080035 BH8080035 25 Gas Inlet Fitting (WhiteRodgers Gas Valve) 26 Gas Outlet Fittings (1/2 Gas Valve) BH8080036 BH8080036 27 Gas Outlet Fitting (WhiteRodgers Gas Valve) 28 Manifold Assembly - Natural Gas BH8080037 BH8080037 28 Manifold Assembly - LPG BH8080093 BH8080090 29 Manifold Inlet Fitting 30 Injector (LPG) BH8080016 BH8080016 30 Injector (NG) BH8080017 BH8080017 31 Wall Bracket Replacement Screw Set including Gas Hose BH8080051 BH8080051 32 Heater Replacement Screw Set 33 Deflector Screw Set including arm BH8080052 BH8080052 34 Transformer 110V-230V (Honeywall) BH8080050 BH8080050 34 Transformer 110V-24V (Fenwal)
TUNGSTEN GAS 300 & 500 White Rodger Honeywell 19 19 17 7 14 6 16 15 13 22 13 20 9 12 4 8 10 5 1 24 11 3 23 2
TUNGSTEN GAS 300 & 500 REPLACEMENT PARTS No. Description Part No. 300 Series Part No. 500 Series 1 Front Cover BH8080039 BH8080040 2 Flame Protector BH8080041 BH8080042 3 Right Side Mount BH8080043 BH8080043 4 Left Side Mount BH8080044 BH8080044 5 Ionization Holder Assembly - including Tungsten spacer BH8080045 BH8080045 6 White Rodger Spacer 7 Control Mount 8 Rear Housing BH8080046 BH8080047 9 Rear Cover Assembly BH8080048 BH8080049 10 Burner BH8080030 BH8080030 11 Wiring Harness + Ignitor Assembly- Honeywell BH8080012 BH8080013 12 Inner Skin BH8080031 BH8080032 13 Wall Bracket Assembly BH8080001 BH8080001 14 Honeywall Control BH8080015 BH8080015 15 Honeywell Gas Valve BH8080014 BH8080014 16 Fenwal Control 17 White Rodger 24V Gas Valve 18 Intentionally left blank 19 Gas Inlet Fitting (Honeywell 1/2 Gas Valve) BH8080035 BH8080035 20 Gas Outlet Fittings ( Honeywell 1/2 Gas Valve) BH8080036 BH8080036 21 Intentionally left blank 22 Gas Outlet Fitting (WhiteRodgers Gas Valve) 23 Manifold Assembly - Natural Gas BH8080037 BH8080038 23 Manifold Assembly - LPG BH8080093 BH8080090 24 Injector (LPG) BH8080016 BH8080016 24 Injector (NG) BH8080017 BH8080017 25 Wall Bracket Replacement Screw Set including Gas Hose BH8080051 BH8080051 26 Intentionally left blank 27 Deflector Screw Set including arm BH8080052 BH8080052 28 Transformer 110V-230V (Honeywall) BH8080050 BH8080050
PLATINUM ELECTRIC REPLACEMENT PARTS No. Description Bromic Part No. 1 Platinum Electric 1500W 2620230 2 Ceiling Recess Kit 2620235 3 Umbrella Mounting Kit 2620236 4 Tube Suspension Kit 2620237 5 Chain Suspension Kit 2620238 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION No heat 1. Improper connection 1. Check connection to power supply Not enough heat Too much heat 1. Heater too small for application 2. Heater mounted too high or too far 1. Heater too large for application 2. Heater mount too low or too close 1. Add additional heater(s) 2. Decrease mounting height or distance 1. Replace with smaller heater 2. Increase mounting height or distance
TUNGSTEN ELECTRIC REPLACEMENT PARTS No. Description BH0420002 (2000W) BH0420003 (3000W) BH0420004 (4000W) BH0420005 (6000W) 1 Tube Element BH8180001 BH8180002 BH8180001 BH8180002 2 Front Cover BH8180003 BH8180004 BH8180003 BH8180004 3 Element End Cover Set BH8180005 BH8180006 BH8180005 BH8180006 4 Junction Box Cover & Seal Set BH8180007 BH8180007 BH8180007 BH8180007 5 Mounting Bracket Set (Short) BH8180008 BH8180008 BH8180008 BH8180008 6 Mounting Bracket Set (Long) BH8180009 BH8180009 BH8180009 BH8180009 7 Ceiling Recess Kit BH8180010 BH8180011 BH8180010 BH8180011 8 Tube Suspension Kit BH8180012 BH8180012 BH8180012 BH8180012 9 Chain Suspension Kit BH8180013 BH8180013 BH8180013 BH8180013 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION Element does not energize 1. Defective element 2. Improper connection 1. Replace element 2. Check connection to power outlet Not enough heat Too much heat Hot spot in Tube 1. Heater too small for application 2. Heater mounted too high or too far 1. Heater too large for application 2. Heater mount too low or too close 1. Heater is not level 2. Grease or moisture on tube 1. Add additional heater(s) 2. Decrease mounting height or distance 1. Replace with smaller heater 2. Increase mounting height or distance 1. Adjust to level mount 2. Clear tube-replace if problem persists
TUNGSTEN PORTABLE PARTS CONTENTS PACKED IN (2) BOXES Box 1 Contents AAA Head Assembly AAA Battery Box 2 Contents Base Assembly Front Assembly Rear Arm Assembly x 2 Side Panels x 2 Top Arms x 2 Rear Cover Top Flame Deflector Regulator
TUNGSTEN PORTABLE REPLACEMENT PARTS No. Description 1 Knob 2 Gas Valve 3 Ignition Pack 4 Rear Cylinder Cover BH8280002 BH8280003 BH8280004 BH8280005 5 6 Side Panel - Cylinder Housing Inner Mesh BH8280006 BH8280007 7 Front Panel Assembly 8 Complete Burner Unit Assembly 9 Thermocouple Assembly 10 Front Cover 11 Ignition and Earth Rod Assembly (incl wiring harness) 12 Heat Deflector Assembly 13 Wheel Kit 14 Screw Set 15 Magnet Assembly 16 Rubber Ring BH8280008 BH8280009 BH8280010 BH8280011 BH8280012 BH8280013 BH8280014 BH8280015 BH8280016 BH8280017 TROUBLESHOOTING Problem Possible Cause What you can do What ONLY an authorized service technician can do Burner will not light Gas valve may be OFF Tank fuel empty Opening blocked Loose connections Low gas pressure Thermocouple bad Not in correct location Turn the gas valve ON Check all fittings Replace cylinder with a new cylinder Refill LPG tank Remove and clean Replace thermocouple Burner will not stay on Loose connections Thermocouple bad Gas leak in line Lack of fuel pressure Tank near empty Tighten connections Check connections Clean dirty area Replace thermocouple Refill LPG tank Burner flame is low Supply hose is bent or twisted Straighten hose and perform lock test on hose Emitter glows uneven Low gas pressure Base is not on a level surface Replace cylinder with a new cylinder Place heater on a level surface Thick black smoke Blockage in burner Turn off the heater and let it cool Carbon build-up Dirt or film on reflector and flame screen Clean reflector and flame screen Remove blockage and clear burner inside and outside