ITEM 6 7 9 0 6 7 9 0 6 7 9 6 QTY 70 7 6 X-VFAW X-HDCAMTBW X-MHTPHD X-VFAPL X-LCBP X-HDCAMSS X-SPTB X-HDCAMSP X-TBCA SC MCP DCP P P6 A GFW GLW GNUT GR- GR- GR- X-UB0 X-UB G07 G06 G0 A G0 GFW GLW GNUT X-UB0 X-UB GFW GLW GNUT PARTS LIST PART SUPPORT ARM CLAMP WELDMENT FOR BCAM-HD MULTI-HOLE TAPER PLATE WELDMENT VFA-HD PIVOT PLATE BENT BACKING PLATE ANGLE ADJUSTMENT WELDMENT FOR BCAM-HD SLIDING PIPE TIE BACK PLATE POSITIONING PLATE WELDMENT FOR BCAM-HD TIE BACK CLIP ANGLE CROSSOVER PLATE CLAMP HALF /" THICK, -/" LONG /" THICK, -/" CNTER TO CENTER CLAMP HALF -7/" X " ( /" SCH. 0) GALVANIZED PIPE -/" X 6" (" SCH. 0) GALVANIZED PIPE /" x -/" UNC HEX BOLT (A) /" HDG USS FLATWASHER /" HDG LOCKWASHER /'' HDG HEAVY H HEX NUT /" x " THREADED ROD (HDG.) /" x " THREADED ROD (HDG.) /" x " THREADED ROD (HDG.) /" X " X -/" X -/" U-BOLT (HDG.) /" X -/" X -/" X " U-BOLT (HDG.) /'' x 7" HDG HEX BOLT GR FULL THREAD /'' x 6" HDG HEX BOLT GR FULL THREAD /" x " HDG HEX BOLT GR /'' x -/" HDG A HEX BOLT /" x " HDG HEX BOLT GR /" HDG USS FLATWASHER /" HDG LOCKWASHER /'' HDG HEAVY H HEX NUT /" X " X X " GALV U-BOLT /" X " X " X -/" U-BOLT (HDG.) /" HDG USS FLATWASHER /" HDG LOCKWASHER /'' HDG HEAVY H HEX NUT LENGTH in in / in 7 in /6 in / in in 6 in / in in 7 in 6 in / in / in / in / in UNIT WT. NET WT. 7...6.6 6. 6...77 9.00.0 6.9 6.9.7.9...0.0.0 9.9.9.7.6.90 0.6.9 0.7.0 0..9 0.06 0. 0.0 0.7 0. 0. 0.0.9.0. 0.70...60.00.00 0.70. 0.6 0.6 0.7.0 0..0 0.. 0.07.76 0.0. 0. 9.7 0.7. 0.60.7 0.0.09 0.0 0. 0.07.9 TOTAL WT. # 69. D UPDATED BCAM VERSION TO BCAM VERSION 6/9/0 C UPDATED PIN LEG CONNECTION TO BCAM CONNECTION //07 B CHANGED TIE-BACK BACK CONNECTION 7/6/07 A CHANGED TIE-BACK FRONT CONNECTION //07 SAWED, SHEARED AND GAS CUT EDGES (± 0.0") DRILLED AND GAS CUT HOLES (± 0.0") - NO CONING OF HOLES LASER CUT EDGES AND HOLES (± 0.00") - NO CONING OF HOLES BENDS ARE ± / DEGREE ALL OTHER MACHINING (± 0.0") 0 //07 BMC //07 --7-76 OF
TIE-BACK POSITIONS TIE-BACK POSITION -0 / +0 TOP PARALLEL TIE-BACK POSITION -0 / -0 TOP CROSS TIE-BACK POSITION -0 SAME SIDE STACKED D UPDATED BCAM VERSION TO BCAM VERSION 6/9/0 C UPDATED PIN LEG CONNECTION TO BCAM CONNECTION //07 B CHANGED TIE-BACK BACK CONNECTION 7/6/07 A CHANGED TIE-BACK FRONT CONNECTION //07 SAWED, SHEARED AND GAS CUT EDGES (± 0.0") DRILLED AND GAS CUT HOLES (± 0.0") - NO CONING OF HOLES LASER CUT EDGES AND HOLES (± 0.00") - NO CONING OF HOLES BENDS ARE ± / DEGREE ALL OTHER MACHINING (± 0.0") 0 //07 BMC //07 --7-76 OF
ANGLE CALIBRATING PROCEDURE: 0 0 0. MEASURE TOWER TAPER AND PICK LOWER BRACKET HOLE: HOLE A = -.6 TO.6 HOLE B =.6 TO 6.. USE CALIBRATING BOLT TO ADJUST FRAME TO DESIRED TAPER STEP STEP FITS LEG SIZES UP TO -/" O.D. 0 /" ± TAPER ADJUSTMENT. TORQUE LOCKING BOLTS TO 00 ft.-lbs.. ADVANCE LOCKING NUT TO POSITIONING PLATE, THEN TIGHTEN. UPPER 7/" B 7" ± B A A LOWER.6 to 6. -.6 to.6 0" VARIABLE D UPDATED BCAM VERSION TO BCAM VERSION 6/9/0 C UPDATED PIN LEG CONNECTION TO BCAM CONNECTION //07 B CHANGED TIE-BACK BACK CONNECTION 7/6/07 A CHANGED TIE-BACK FRONT CONNECTION //07 SAWED, SHEARED AND GAS CUT EDGES (± 0.0") DRILLED AND GAS CUT HOLES (± 0.0") - NO CONING OF HOLES LASER CUT EDGES AND HOLES (± 0.00") - NO CONING OF HOLES BENDS ARE ± / DEGREE ALL OTHER MACHINING (± 0.0") 0 //07 BMC //07 --7-76 OF
9 6 0 6 OR 9 6 OR 0 OR B F D A OR DETAIL A 7 7 6 6 DETAIL B C G E 7 7 6 DETAIL C 6 9 9 DETAIL D 9 9 X 7/6" LUG HOLES REVIEW CARRIER STANDARDS FOR PROPER SURFACE PREPARTION AND ASSEMBLY OF ELECTRICAL CONNECTIONS DETAIL G 9/6" SLOTTED HOLE FOR EQUIPMENT PIPE U-BOLT DETAIL E 9 DETAIL F D UPDATED BCAM VERSION TO BCAM VERSION 6/9/0 C UPDATED PIN LEG CONNECTION TO BCAM CONNECTION //07 B CHANGED TIE-BACK BACK CONNECTION 7/6/07 A CHANGED TIE-BACK FRONT CONNECTION //07 SAWED, SHEARED AND GAS CUT EDGES (± 0.0") DRILLED AND GAS CUT HOLES (± 0.0") - NO CONING OF HOLES LASER CUT EDGES AND HOLES (± 0.00") - NO CONING OF HOLES BENDS ARE ± / DEGREE ALL OTHER MACHINING (± 0.0") 0 //07 BMC //07 --7-76 OF
UNISTRUT AND HARDWARE SOLD SEPARATELY. REQUIRES /" HARDWARE D UPDATED BCAM VERSION TO BCAM VERSION 6/9/0 C UPDATED PIN LEG CONNECTION TO BCAM CONNECTION //07 B CHANGED TIE-BACK BACK CONNECTION 7/6/07 A CHANGED TIE-BACK FRONT CONNECTION //07 SAWED, SHEARED AND GAS CUT EDGES (± 0.0") DRILLED AND GAS CUT HOLES (± 0.0") - NO CONING OF HOLES LASER CUT EDGES AND HOLES (± 0.00") - NO CONING OF HOLES BENDS ARE ± / DEGREE ALL OTHER MACHINING (± 0.0") 0 //07 EQUIPMENT PIPE AND HARDWARE SOLD SEPARATELY. REQUIRES /" HARDWARE AND -/" TO -/" O.D. PIPE BMC //07 --7-76 OF