X*PERT TM SERIESS INSTALLATION AND OPERATING INSTRUCTIONS MODE EL: HDDi/HDDiS/HDXi HOLDING DRAWERS INTENDED FOR OTHER THAN HOUSEHOLD USE RETAIN THIS MANUAL FOR FUTURE REFERENCE UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES! FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.!! WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment.! Initial heating of unit may generate smoke or fumes and must be done in a well ventilated area. Overexposure to smoke or fumes may cause nausea or dizziness. This equipment has been engineered to provide you with year-round dependable service when used according to the instructions in this manual and standard commercial kitchen practices Phone: (97) 9- Fax: () 55-97 Toll Free: () 57- Website: www.apwwyott.com E-mail: info@apwwyott.com P/N 753 Rev A /3 APW WYOTT 37 N Watters Rd STE Allen, TX 753
TABLE OF CONTENTS SECTION ITEM PAGE. Owners Information... General Information... General Operation Instructions... Warranty Information.... Important Safety Information... 3 3. Specifications... 3 Electrical... 3 Dimensions.... Operation... 5 5. Cleaning... General Cleaning Instructions... Daily Cleaning.... Troubleshooting... 7. Wiring Diagrams... 7. HDDi/HDXi/HDDiS Counter Exploded View... 9 HDDi/HDXi Counter Parts List... HDDiS Counter Parts List... 9. HDDi/HDXi/HDDiS Built-In Exploded View... HDDi/HDXi Built-In Parts List... 5 HDDiS Built-In Parts List..... 7. Warranty... General Information:. OWNER S INFORMATION. Always clean equipment thoroughly before first use. (See general cleaning instructions).. Check rating label for your model designation and electrical rating. 3. For best results, use stainless steel countertops.. All dimensions in parenthesis in centimeters unless noted. 5. Legs are shipped unassembled. Legs must be screwed into base of unit. General Operation Instructions:. All foodservice equipment should be operated by trained personnel.. Do not allow your customers to come in contact with any surface labeled CAUTION HOT. 3. Where applicable: Never pour cold water into dry heated units.. Never hold food below 5 F ( C). Warranty Information: Reliability Backed By APW Wyott s Warranty: All APW Wyott Holding Drawers are backed by a one year parts and labor warranty, including On-Site Service calls within 5 miles of authorized service technicians. Service Information: Service Hotline () 733-3
. SAFETY INFORMATION APW Wyott Holding Drawers are designed, built and sold for commercial use and should be operated by trained personnel only. Clearly post all CAUTIONS, WARNINGS and OPERATING INSTRUCTIONS near each unit to insure proper operation and to reduce the chance of personal injury and/or equipment damage. Always disconnect power before servicing the Holding Drawer. Surfaces will remain hot after power has been turned off. Allow unit to cool before cleaning or servicing. Never clean the Holding Drawer by immersing it in water. The Holding Drawer is not protected against water jets; DO NOT CLEAN HOLDING DRAWER WITH A WATER JET. Always clean equipment before first use. Cordset Configuration: 3. SPECIFICATIONS HDDi/HDDiS/HDXi-- USES NEMA 5-5P HDDi/HDDiS/HDXi -3- USES NEMA 5-5P HDDi/HDDiS/HDXi -- USES NEMA -5P HDDi/HDDiS/HDXi -3- USES NEMA -5P HDDi/HDDiS/HDXi -- USES NEMA -5P HDDi/HDDiS/HDXi -3- USES NEMA -5P HDDi/HDDiS/HDXi -- USES NEMA 5-5P HDXi-- USES NEMA 5-P HDDi/HDDiS/HDXi -- USES NEMA -5P HDXi-- USES NEMA -5P HDDi/HDDiS/HDXi -- USES NEMA -5P HDXi-- USES NEMA -5P NEMA 5-5P NEMA 5-P NEMA -5P If the supply cord is damaged, the manufacturer or an authorized service agent or a similarly qualified person must replace it to avoid a hazard or voiding the warranty.! WARNING: ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH. Electrical Ground is required on this appliance. DO NOT modify the power supply cord plug. If it does not fit into the outlet, have the proper outlet installed by a qualified electrician. DO NOT use an extension cord with this appliance. Check with a qualified electrician if you are unsure as to whether the appliance is properly grounded.! 3
Overall Dimensions & Electrical Specifications Model Volts, Power Amps Overall Height Overall Width Overall Depth Cutout Shipping Number Hz Rating Counter Built-in Counter Built-in Counter Built-in Built-in Weight HDDi-- HDDi-- HDDi-- HDDi-- HDDi-- HDDi-- HDDi-3- HDDi-3- HDDi-3- HDDiS-- HDDiS-- HDDiS-- HDDiS-- HDDiS-- HDDiS-- HDDiS-3- HDDiS-3- HDDiS-3- HDXi-- HDXi-- HDXi-- HDXi-- HDXi-- HDXi-- HDXi-3- HDXi-3- HDXi-3- HDXi--* HDXi--* HDXi--* V (Hz) Watts A in (mm) in (mm) in (mm) in (mm) lbs (kg) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) (5/) 5 3.75-7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 5. -7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 5. -7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9 7.5 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9.33 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9 3.75 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35.5 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35.9 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35 5.3 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 5 3.75-7/ (37) -/ () -/ (55) -/ (55) 9 (737) -5/ (77) 5. -7/ (37) -/ () -/ (55) -/ (55) 9 (737) -5/ (77) 5. -7/ (37) -/ () -/ (55) -/ (55) 9 (737) -5/ (77) 9 7.5 -/ () -7/ (59) -/ (55) -/ (55) 9 (737) -5/ (77) 9.33 -/ () -7/ (59) -/ (55) -/ (55) 9 (737) -5/ (77) 9 3.75 -/ () -7/ (59) -/ (55) -/ (55) 9 (737) -5/ (77) 35.5 33-5/ (5) 9-3/ (757) -/ (55) -/ (55) 9 (737) -5/ (77) 35.9 33-5/ (5) 9-3/ (757) -/ (55) -/ (55) 9 (737) -5/ (77) 35 5.3 33-5/ (5) 9-3/ (757) -/ (55) -/ (55) 9 (737) -5/ (77) 5 3.75-7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 5. -7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 5. -7/ (37) -3/ (3) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9 7.5 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9.33 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 9 3.75 -/ () 9-3/ (5) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35.5 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35.9 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) 35 5.3 33-5/ (5) 9-/ (7) 7-3/ (7) 7-3/ (7) (53) -5/ (5) -3/x (73x7) -3/x (73x7) -3/x (73x7) x (5x7) x (5x7) x (5x7) 9-/x (79x7) 9-/x (79x7) 9-/x (79x7) -/x-/ (x5) -/x-/ (x5) -/x-/ (x5) -3/x-/ (57x5) -3/x-/ (57x5) -3/x-/ (57x5) 3x-/ (7x5) 3x-/ (7x5) 3x-/ (7x5) -3/x (73x7) -3/x (73x7) -3/x (73x7) x (5x7) x (5x7) x (5x7) 9-/x (79x7) 9-/x (79x7) 9-/x (79x7) 5 (57) 5 (57) 5 (57)) 75 (79) 75 (79) 75 (79) 5 () 5 () 5 () 5 (57) 5 (57) 5 (57)) 75 (79) 75 (79) 75 (79) 5 () 5 () 5 () 5 (57) 5 (57) 5 (57)) 75 (79) 75 (79) 75 (79) 5 () 5 () 5 () 5. 5 (9) N/A 7-3/ (7) N/A (53) N/A N/A 75 (5).5 5 (9) N/A 7-3/ (7) N/A (53) N/A N/A 75 (5) 7.5 5 (9) N/A 7-3/ (7) N/A (53) N/A N/A 75 (5) *MODELS COME STANDARD WITH LEGS
. OPERATION. Set thermostat control to 9 F and preheat each drawer for 3 minutes.. Place food product directly in stainless steel drawer pans or use any combination of full or fractional pans up to (5mm) deep. 3. Set front vent to desired position for maintaining food product moisture.. Perforated pans may be used with damp towel or small amount of hot water in the drawer pan to prevent food dry out. CAUTION: Use no more than quart ( liter) for wet operation. 5. If too much moisture accumulates around drawer front or vent, reduce temperature setting or move vent to dry position. PRODUCT TEMPERATURE SETTING VENT PRODUCT TEMPERATURE SETTING VENT Rolls, Bread - F (7 - C) Moist Vegetables - F (7 - C) Moist Meats - F (7 - C) Moist NOTE: Temperature and vent settings will require adjustment according to type and quantity of food, and number of times drawer is opened during operation. Digital Controller Operation (HDXi models only) With unit plugged in and the rocker switch in the ON position, the digital controller will come on. When the controller is on, the minimum set point value is preset to F and the maximum set point is 3 F. To obtain the desired set point, push the set key and release. You have two seconds to adjust the set temperature. Press the up or down key to your desired setting. After setting desired temperature, release up or down key and press the set key. The controller display should return to the measured temperature of the unit. SET ARROW KEY DOWN ARROW KEY UP ARROW KEY 5
General Cleaning Instructions: 5. CLEANING. NEVER clean any electrical unit by immersing it in water. Turn off before surface cleaning.. Always clean equipment thoroughly before first use. Clean unit daily. Use warm, soapy water. Mild cleansers and PLASTIC scouring pads may be used to remove baked-on food and water scale. 3. Turn off electrical units before cleaning or servicing. All service should be performed by an APW authorized service agency. Daily Cleaning:. Follow General Cleaning instructions (above).. Remove any inset pans and drawer pans. Wash thoroughly in the sink or dishwasher. 3. Remove drawer: Remove pans and pan inserts. Extend drawer and lift up on the front to clear the drawer stop. Lower drawer and lift over front cabinet bearing. Always ask and check the following:. TROUBLESHOOTING GUIDE. Is the unit connected to a live power source of the proper voltage?. Check the circuit breaker. 3. Is power switch ON (HDXi models only). Is the thermostat set to a temperature? 5. Is the Pilot light glowing?. Check the rating label. Is the unit connected to the correct power source?
7. WIRING DIAGRAMS HDDi/HDDiS WIRING DIAGRAMS NOTE: Wire # s 5 & are not used in HDDi/HDDiS-. Wire # s 9 & are only used in HDDi/HDDiS-3 7
5 3 3 7 9 3 3 3 9 7 5 5 9 7 3 9
PARTS LIST(QTY S) HDDi- HDDi- HDDi-3 HDXi- HDXi- HDXi-3 ITEM PN DESCRIPTION 755 HEATING ELEMENT, V 3 3 75 HEATING ELEMENT, V 3 3 757 HEATING ELEMENT, V 3 3 3393 TOP COVER 3 33973 OUTER SIDE PANEL 3393 OUTER SIDE PANEL 3399 OUTER SIDE PANEL 3397 CONTROL PANEL 3395 CONTROL PANEL 33993 CONTROL PANEL 759 CONTROL PANEL 7597 CONTROL PANEL 759 CONTROL PANEL 5 59 CONTROL DECAL 57 CONTROL DECAL 57 CONTROL DECAL 573 CONTROL DECAL 57 CONTROL DECAL 575 CONTROL DECAL 95 THERMOMETER 3 3 3 DIGITAL CONTROLLER 73 V 3 DIGITAL CONTROLLER 735 V 3 3 7 TEMPERATURE PROBE (V/V) 3 3 3 7 9 THERMOSTAT 3 3 3 55 KNOB 3 3 3 9 59 PILOT LIGHT 3 3 3 335 DRAWER SLIDE ROLLER 93 MACHINE SCREW 353 RIVNUT 3 955 LOOP CLAMP S/S 3 3 3 3 3 3 33 TERMINAL BLOCK 5 3 INSULATION X9X 9 9 9 9 9 9 75 LEG SUPPORT BASE 9 9 9 9 9 9
PARTS LIST(QTY S) HDDi- HDDi- HDDi-3 HDXi- HDXi- HDXi-3 ITEM PN DESCRIPTION 7 737-999- -999- LEG, STAINLESS " (OPTIONAL) CASTER, 3" (OPTIONALKIT OF ) CASTER, 5" (OPTIONAL KIT OF ) 535 CORDSET 55 CORDSET 9 9 STRAIN RELEIF 759 OUTER BACK PANEL 75 OUTER BACK PANEL 759 OUTER BACK PANEL 3393 TOP BRACE ASSY 33975 RIGHT SIDE BRACE 3395 RIGHT SIDE BRACE 3399 RIGHT SIDE BRACE 3 757 RIGHT SIDE DRAWER SLIDE 3 3 3 3 3 3 7573 LEFT SIDE DRAWER SLIDE 3 3 3 3 3 3 5 7577 STANDARD PAN X 3 3 3 3 3 3 97 SCREW, /-X3/" 7 75 FLAT ROLLER BEARING 757 CENTER PAN SUPPORT ASSY 3 3 3 3 3 3 9 55 HANDLE (ALSO NEED 3&3) 3 3 3 3 3 3 3 SCREW, -X" 3 97 WASHER, # INTERNAL TEETH 3 75 DRAWER ASSY (INCLUDES 5-3) 3 3 3 3 3 3 N/A 755 WIRE SET N/A 757 WIRE SET N/A 759 WIRE SET N/A 753 MANUAL
PARTS LIST(QTY S) ITEM PN DESCRIPTION HDDiS- HDDiS- HDDiS-3 HDXiS- HDXiS- HDXiS-3 5 HEATING ELEMENT, V 3 3 55 HEATING ELEMENT, V 3 3 5 HEATING ELEMENT, V 3 3 7539 TOP COVER 3 753 OUTER SIDE PANEL 757 OUTER SIDE PANEL 759 OUTER SIDE PANEL 3397 CONTROL PANEL 3395 CONTROL PANEL 33993 CONTROL PANEL 759 CONTROL PANEL 7597 CONTROL PANEL 759 CONTROL PANEL 5 59 CONTROL DECAL 57 CONTROL DECAL 57 CONTROL DECAL 573 CONTROL DECAL 57 CONTROL DECAL 575 CONTROL DECAL 95 THERMOMETER 3 3 3 DIGITAL CONTROLLER 73 V 3 DIGITAL CONTROLLER 735 V 3 3 7 TEMPERATURE PROBE (V/V) 3 3 3 7 9 THERMOSTAT 3 3 3 55 KNOB 3 3 3 9 59 PILOT LIGHT 3 3 3 335 DRAWER SLIDE ROLLER 93 MACHINE SCREW 353 RIVNUT 3 955 LOOP CLAMP S/S 3 3 3 3 3 3 33 TERMINAL BLOCK 5 3 INSULATION X9X 9 9 9 9 9 9 753 LEG SUPPORT BASE
PARTS LIST(QYT S) ITEM PN DESCRIPTION HDDiS- HDDiS- HDDiS-3 HDXiS- HDXiS- HDXiS-3 7 95 LEG, BLACK 737 LEG, STAINLESS " (OPTIONAL) -999- CASTER, 3" (OPTIONAL KIT OF ) -999- CASTER, 5" (OPTIONAL KIT OF ) 535 CORDSET 55 CORDSET 9 9 STRAIN RELEIF 757 OUTER BACK PANEL 757 OUTER BACK PANEL 7555 OUTER BACK PANEL 7557 TOP BRACE ASSY 33975 RIGHT SIDE BRACE 3395 RIGHT SIDE BRACE 3399 RIGHT SIDE BRACE 3 757 RIGHT SIDE DRAWER SLIDE 3 3 3 3 3 3 7573 LEFT SIDE DRAWER SLIDE 3 3 3 3 3 3 5 7577 STANDARD PAN X 3 3 3 3 3 3 97 SCREW, /-X3/" 7 75 FLAT ROLLER BEARING 757 CENTER PAN SUPPORT ASSY 3 3 3 3 3 3 9 553 HANDLE (ALSO NEED 3&3) 3 3 3 3 3 3 3 SCREW, -X" 3 97 WASHER, # INTERNAL TEETH 3 753 DRAWER ASSY (INCLUDES 5-3) 3 3 3 3 3 3 N/A 755 WIRE SET N/A 757 WIRE SET N/A 759 WIRE SET N/A 753 MANUAL 3
3 3 7 9 5 3 3 9 9 5 7 5 3
PARTS LIST(QTY S) ITEM PN DESCRIPTION HDDi- HDDi- HDDi-3 HDXi- HDXi- HDXi-3 755 HEATING ELEMENT, V 3 3 75 HEATING ELEMENT, V 3 3 757 HEATING ELEMENT, V 3 3 7539 TOP COVER 3 753 OUTER SIDE PANEL 757 OUTER SIDE PANEL 759 OUTER SIDE PANEL 3397 CONTROL PANEL 3395 CONTROL PANEL 33993 CONTROL PANEL 759 CONTROL PANEL 7597 CONTROL PANEL 759 CONTROL PANEL 5 59 CONTROL DECAL 57 CONTROL DECAL 57 CONTROL DECAL 573 CONTROL DECAL 57 CONTROL DECAL 575 CONTROL DECAL 95 THERMOMETER 3 3 3 73 DIGITAL CONTROLLER V 3 735 DIGITAL CONTROLLER V 3 3 TEMPERATURE PROBE 7 (V/V) 3 3 3 7 9 THERMOSTAT 3 3 3 55 KNOB 3 3 3 9 59 PILOT LIGHT 3 3 3 335 DRAWER SLIDE ROLLER 93 MACHINE SCREW 353 RIVNUT 3 955 LOOP CLAMP S/S 3 3 3 3 3 3 33 TERMINAL BLOCK 5 3 INSULATION X9X 9 9 9 9 9 9 339 FRONT PLATE 3393 FRONT PLATE 33999 FRONT PLATE 5
PARTS LIST(QTY S) ITEM PN DESCRIPTION HDDi- HDDi- HDDi-3 HDXi- HDXi- HDXi-3 9 559 HOLE PLUG 757 OUTER BACK PANEL 757 OUTER BACK PANEL 7555 OUTER BACK PANEL 7557 TOP BRACE ASSY 33975 RIGHT SIDE BRACE 3395 RIGHT SIDE BRACE 3399 RIGHT SIDE BRACE 3 75 RIGHT SIDE DRAWER SLIDE 3 3 3 3 3 3 759 LEFT SIDE DRAWER SLIDE 3 3 3 3 3 3 5 7577 STANDARD PAN X 3 3 3 3 3 3 97 SCREW, /-X3/" 7 75 FLAT ROLLER BEARING 757 CENTER PAN SUPPORT ASSY 3 3 3 3 3 3 9 553 HANDLE (ALSO NEED 3&3) 3 3 3 3 3 3 3 SCREW, -X" 3 97 WASHER, # INTERNAL TEETH 3 753 DRAWER ASSY (INCLUDES 5-3) 3 3 3 3 3 3 N/A 755 WIRE SET N/A 757 WIRE SET N/A 759 WIRE SET N/A 753 MANUAL
PARTS LIST(QTY S) ITEM PN DESCRIPTION HDDiS- HDDiS- HDDiS-3 HDXiS- HDXiS- HDXiS-3 5 HEATING ELEMENT, V 3 3 55 HEATING ELEMENT, V 3 3 5 HEATING ELEMENT, V 3 3 7579 TOP COVER 3 75 75 OUTER RIGHT SIDE PANEL OUTER LEFT SIDE PANEL 759 759 OUTER RIGHT SIDE PANEL OUTER LEFT SIDE PANEL 75 757 OUTER RIGHT SIDE PANEL OUTER LEFT SIDE PANEL 3397 CONTROL PANEL 3395 CONTROL PANEL 33993 CONTROL PANEL 759 CONTROL PANEL 7597 CONTROL PANEL 759 CONTROL PANEL 5 59 CONTROL DECAL 57 CONTROL DECAL 57 CONTROL DECAL 573 CONTROL DECAL 57 CONTROL DECAL 575 CONTROL DECAL 95 THERMOMETER 3 3 3 73 DIGITAL CONTROLLER V 3 735 DIGITAL CONTROLLER V 3 3 TEMPERATURE PROBE 7 (V/V) 3 3 3 7 9 THERMOSTAT 3 3 3 55 KNOB 3 3 3 9 59 PILOT LIGHT 3 3 3 335 DRAWER SLIDE ROLLER 93 MACHINE SCREW 353 RIVNUT 3 955 LOOP CLAMP S/S 3 3 3 3 3 3 33 TERMINAL BLOCK 5 3 INSULATION X9X 9 9 9 9 9 9 757 FRONT PLATE 75 FRONT PLATE 75 FRONT PLATE 7
PARTS LIST(QYT S) ITEM PN DESCRIPTION HDDiS- HDDiS- HDDiS-3 HDXiS- HDXiS- HDXiS-3 9 559 HOLE PLUG 75 OUTER BACK PANEL 759 OUTER BACK PANEL 755 OUTER BACK PANEL 7557 TOP BRACE ASSY 33975 RIGHT SIDE BRACE 3395 RIGHT SIDE BRACE 3399 RIGHT SIDE BRACE 3 757 RIGHT SIDE DRAWER SLIDE 3 3 3 3 3 3 7573 LEFT SIDE DRAWER SLIDE 3 3 3 3 3 3 5 7577 STANDARD PAN X 3 3 3 3 3 3 97 SCREW, /-X3/" 7 75 FLAT ROLLER BEARING 757 CENTER PAN SUPPORT ASSY 3 3 3 3 3 3 9 553 HANDLE (ALSO NEED 3&3) 3 3 3 3 3 3 3 SCREW, -X" 3 97 WASHER, # INTERNAL TEETH 3 753 DRAWER ASSY (INCLUDES 5-3) 3 3 3 3 3 3 N/A 755 WIRE SET N/A 757 WIRE SET N/A 759 WIRE SET N/A 753 MANUAL
IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required. Model Number Serial Number Date Purchased Notes: 9