Temperature Controllers

Temperature Controllers

Temperature Controllers No one can provide more affordable, more dependable or more accurate temperature control equipment than Thermal Care. Every temperature control unit is designed and built to meet or exceed the exacting performance standards demanded by today s manufacturing environment. Choose from several models Our complete line of temperature control equipment includes several types of controllers for use in manufacturing applications. The well-known Aquatherm RA Series, RD Series, and RE Series come in several different configurations and are possibly the best units available today at the lowest possible prices. Our popular Oiltherm RO Series hot oil temperature controllers are designed for a range of high temperature applications, and the economical Vactherm RV Series positive/negative pressure temperature controllers provide better temperature control than competitive designs when a process leak develops. Affordable, compact designs With several different configurations and model designations to choose from, it s likely that Thermal Care can match your specification with a unit directly from stock. All units are pre-wired, pre-piped and ready to install. Backed by experience You benefit from our many years of experience with process cooling and temperature control. Our experienced staff also provides a full range of customer support services to assure maximum product performance now and for years to come. When Thermal Care offers so much, why consider any other temperature controller source. The choice is obvious it s Thermal Care for quality temperature control equipment. Aquatherm controllers come with a 5-year controller warranty and lifetime exchange price of $175 (RE Series units come with 2-year warranty) Temperature Controllers from Thermal Care possibly the best available anywhere, at the best possible price

Control Panel STANDARD AQUATHERM CONTROLLER FEATURES 15 lights and 7 snap action switches Two easy-to-read LED digital displays showing To Process and Set Point temperatures Entire panel is sealed protecting controller against contamination from dirt or water Panel viewing angle is easy-to-read Switch between ºF/ºC temperature readout easily from front panel PID control for + 1ºF accuracy Automatic fine tuning of PID parameters Self-adjusting high/low temperature alarm deviation Power failure indicator signals brown out Automatic air purge cycle Auto vent cancel prevents venting above 150ºF Thirty-minute deviation delay stops nuisance alarms during start-up and set point change 260ºF high temperature safety State-of-the-art microprocessor control The temperature accuracy of every unit depends on its control system and Aquatherm Series temperature controllers come standard with a microprocessorbased control system designed exclusively for Thermal Care. The panel s two large digital displays make it easy to set or read system temperatures. The entire control panel is simple to understand and operate without confusing codes or useless buttons. New feature extends seal life Most everyone knows that sustained and excessive heat can reduce the life of the seals on your equipment. Aquatherm RA Series and RD Series units now come standard with Seal-Saver control software built into the microprocessor that automatically cools the process water to 90ºF. This also helps to lower hose temperatures and to prevent potential burns to the equipment operator. After activation, Aquatherm units will automatically shut down as soon as the process water reaches the pre-determined temperature level (90ºF) so your equipment can run longer with fewer seal failures. It s standard and very simple to activate with no difficult controller programming to master. Convenient controller features The unique four-plug wiring design found on Aquatherm controllers allows the entire control board to be quickly and easily replaced if necessary. To protect the controls from dirt or water, the panel overlay is sealed against contamination. A basic, less expensive, off-the-shelf 1/16 DIN plug-in type controller with on/off/vent switch comes standard on Aquatherm RE Series units. Remote control option A hand-held remote control panel is optional and includes all the lights, switches and display functions found on the machine mounted controller. The remote control panel connects using a small 8-wire phone line and will operate a unit from a distance of up to 50 feet. The remote control panel option is available for both Aquatherm RA Series and RD Series units. OPTIONAL AQUATHERM CONTROLLER FEATURES Hand-held, remote control operator panel SPI communications Audible horn From Process temperature readout Remote alarm contacts Remote on/off contacts Remote thermocouple/ RTD input

Aquatherm RA Series Units No other water temperature controller on the market today provides more value than the Aquatherm RA Series from Thermal Care. Units are made with the best available components like premium-quality solenoid valves, high flow pumps with leak-resistant carbon Ni-Resist seals and rugged incoloy heaters. The cast, twin tank/pump assembly is so tough it comes with an exclusive lifetime warranty. Dependable and accurate control The microprocessor-based controller is easy to operate and two digital displays assure accurate temperature settings and readouts. The sturdy cabinet takes up less than two square feet of floor space and units can be stacked when floor space is at a premium. The angled control panel is easy to read and operate. Or, an optional remote control panel allows operation from a distance of up to 50 feet. Many sizes to choose from Standard models come in a complete range of sizes from 3/4 to 7-1/2 hp, 9 to 24kw in either single or dual-zone designs. Check out our big selection of pre-engineered options that allow us to customize an Aquatherm temperature controller for your exact application. Options include: Hand-held remote control panel SPI Communications Motorized, modulating ball valve Process water air purge Closed-circuit design with heat exchanger Dual zone configuration 36kw, 48kw and 60kw units Nonferrous coatings on castings Pressure gauges EXCLUSIVE WARRANTIES Thermal Care is so certain the Aquatherm RA Series temperature control units you purchase will provide years of maintenance-free operation that we offer the following warranties at no extra cost! RA Series Units 2-year warranty on parts 2-year warranty on labor Lifetime warranty on complete twin tank/ pump volute casing assembly Lifetime warranty on pump seal 5-year warranty on controller Lifetime controller exchange price of $175 Aquatherm RA Series units are widely accepted and provide unequalled value

Removable side, top and front panels provides easy access to entire interior Bypass line protects heater and pump if process flow is shut off Long-life, low-watt density incoloy heaters (9-24kw) resist corrosion better than copper or stainless steel High capacity pump (3/4 to 7-1/2 hp) comes with bronze or stainless steel impellers for turbulent flow Seal flush line assures continuous flow across seal to remove contaminants and extend seal life (not visible) Leak-proof, cast twin tank/ pump assembly eliminates pipe fittings and flow restrictions, comes with lifetime warranty Premium quality solenoid valve assures precise temperatures Electrical components mounted in front are easily accessible and isolated from water. Adjustable water supply pressure switch prevents operation at low supply pressure Built-in sediment trap settles contaminants away from pump seal Pump seal made of leak-resistant carbon Ni-Resist, comes with lifetime warranty RA Series

Aquatherm RD & RE Series Units Aquatherm RD Series temperature controllers offer all the features of our full-sized unit in a smaller design Aquatherm RE Series temperature controllers comes with fewer standard features and a lower price EXCLUSIVE WARRANTIES Thermal Care builds Aquatherm RD Series and RE Series temperature control units with quality components for years of maintenancefree operation and offers the following warranties at no extra cost! RD Series Units 2-year warranty on parts 2-year warranty on labor Lifetime warranty on complete twin tank/ pump volute casing assembly Lifetime warranty on pump seal 5-year warranty on controller Lifetime controller exchange price of $175 RE Series Units 1-year warranty on parts 2-year warranty on controller Don t let the smaller size fool you. Aquatherm RD Series and RE Series units provide the same accurate and reliable temperature control as our full-sized units in a smaller cabinet. Built with rugged components for years of worry-free operation, no other controller on the market today comes with more standard features at this price. Easily accessible interior Both RD Series and RE Series units come with permanently attached, tools-free cabinet locking hardware so users can easily access interior components. The control panel opens by loosening a thumbscrew and simply flipping the hinged panel forward. Eight unique re-locking clips keep the exterior cabinet securely in place during use. Inside are high capacity pumps, leakproof, cast twin tank/pump assemblies and premium quality solenoid valves. Fits most applications Standard models are available for applications requiring between 3/4 and 3 hp. The RD Series units come with the same microprocessor-based control panel found on our RA Series units. For a less expensive alternative, our RE Series units come with an off-the-shelf 1/16 DIN plug-in type controller and on/off/vent switch. Aquatherm RE Series temperature controllers provide a less expensive control option

Long-life, low-watt density incoloy heater resists corrosion better than copper or stainless steel Bypass line protects heater and pump if process flow is shut off Leak-proof, cast twin tank/ pump assembly eliminates pipe fittings and flow restrictions, comes with lifetime warranty Two pressure gauges show supply and return water pressure (optional) Tools-free hardware allows easy access to interior components Seal flush line assures continuous flow across seal to remove contaminants and extend seal life High capacity pump (3/4 to 3 hp) comes with bronze or stainless steel impellers for turbulent flow Premium quality solenoid valve assures precise temperatures Pump seal made of leak-resistant carbon Ni-Resist, comes with lifetime warranty Adjustable water supply pressure switch prevents operation at low supply pressure Four swivel casters make the unit easy to move RD & RE Series

Oiltherm RO Series Units Oiltherm RO Series units come in sizes from 6 to 36kw and are designed for operation to 575ºF STANDARD WARRANTY Oiltherm RO Series units are manufactured with high quality components and will provide years of accurate, on-the-job performance. Oiltherm RO Series units come with the following standard warranty. RO Series Units 1-year warranty on parts Designed and constructed for many years of dependable operation, the Oiltherm RO Series hot oil temperature controllers come standard with features like automatic oil preheat and fan cooled controls. The multistage centrifugal pump, located in the reservoir, eliminates leaks associated with positive displacement pumps. More features, more performance Oiltherm RO Series units come with important features not found on competitive units like insulated oil lines and a built-in full-week timer. By having a timer heat the process oil for several hours prior to starting production, a smaller heater can be used. Multiple 3kw low-watt density heaters provide a built-in standby. Heaters operate in two banks for better temperature control. Wide range of temperatures Compact Oiltherm RO Series units come in sturdy cabinets and are built for a wide range of high temperature applications in the 125ºF to 575ºF range. The unique design assures high velocity oil flow across heater elements for optimum heat transfer and longer heater and fluid life. A password lockout protects temperature set points and the microprocessor-based control systems allows customized settings for daily start/stop times and a temperature deviation alarm. Built-in heat exchanger Every unit comes standard with a cooling circuit where plant water is introduced into a stainless steel heat exchanger in the oil tank. The free-floating heat exchanger coil permits expansion that occurs with thermal shock. Oiltherm RO Series units are also available with a negative pressure option that reduces the possiblity of operator injury due to small leaks and allows the process oil to be drained.

Insulated hot oil lines and circuitry for energy efficiency and safety Convenient oil fill location allows oil to be added without removing cabinet Leak-proof centrifugal pump without rotating seals Low oil level switch prevents operation under low oil conditions Control cabinet fan protects control systems and pumps Inlet strainer on cooling water line prevents contamination Insulated oil reservoir maintains temperature and saves energy Stainless steel heat exchanger for corrosive-free operation Premium quality solenoid valve assure precise temperatures RO Series

Vactherm RV Series Units Vactherm RV Series positive/negative pressure temperature controllers eliminate downtime caused by coolant leaks in a mold or process water circuit. The unique design of Vactherm RV Series units allows the vacuum level to be adjusted to exactly the amount necessary to stop the leak, without drawing air into the water circuit. This provides better temperature control at a lower flow rate than competitive designs. And, Vactherm RV Series units can be run as nonferrous temperature controllers even when no leak is present. Change molds fast Leave it to Thermal Care to design a unit with an automatic mold drain that permits users to change molds quickly without a hassle. Only Vactherm RV Series units come with this exclusive quick-change feature. Process water always stays isolated from cooling water thanks to a special stainless steel water circuit with automatic water makeup feature and nonferrous components in water path to assure only clean water in the mold. Extremely easy to operate Temperatures and set points are easy to read on the simple-to-operate control panel. A built-in, full-week timer lets users automatically start or stop operation and adjustable temperature deviation indicator (with audible alarm and silencer) permits users to set and customize operating parameters. Keep production moving despite mold leaks with a dependable, accurate microprocessor-based Vactherm RV Series temperature controller. Vactherm RV Series units are easy to operate and can help eliminate costly downtime STANDARD WARRANTY Vactherm RV Series units are compact, built for years of dependable operation and come with the following standard warranty. RV Series Units 1-year warranty on parts Vactherm RV Series units eliminate mold leaks while minimizing the amount of air drawn into process water

Stainless steel centrifugal pump protects against corrosion Inlet strainer protects against debris in water Solenoid valve automatically fills tank Dual, stainless steel, low-watt density heater elements provide long life and built-in standby Vacuum adjusting valve eliminates leak without pulling air into mold Solenoid valve regulates cooling in stainless steel heat exchanger Insulated stainless steel reservoir holds 4.5 gallons, assures temperature stability and air separation Four swivel casters make unit easy to move RV Series

Aquatherm Configuration Options For dual-zone applications, or if floor space is at a premium, stack RA Series units two-high without expensive racks RD Series and RE Series units can be stacked on our optional, inexpensive rack RAD Series units are perfect for dual-zone applications and house two units in one sturdy cabinet Thermal Care is a leading manufacturer of a complete line of heat transfer equipment and related services that includes: Portable Chillers Available in air and water-cooled models from 1/2 to 40 tons; every portable chiller comes with our unique, easy-to-operate microprocessor-based controller with dual, digital displays and 19 diagnostic indicators. Chiller components are easily accessible and controller comes with 5-year warranty. Pump/Reservoir Systems Every pump/reservoir is custom engineered for its application and includes a solid deck, Victaulic (grooved pipe connecting system) trim, mounted control panel and non-overloading pumps. Reservoirs are available in fiberglass, steel or stainless steel in sizes to 6000 gallons. 7720 N. Lehigh Avenue Niles, Illinois 60714-3491 Central Chillers Designed to meet most application needs in a wide variety of sizes from 20 tons. Our designs include air-cooled, water-cooled or remote condenser models. Modular, belt-drive, direct-drive and multiple circuit (with scroll or discus compressors). Cooling Towers Built of 100% nonferrous materials, our cooling towers are ruggedly designed and manufactured to exacting specifications. All towers come with a full 5-year warranty on the complete tower, including the motor. Water Treatment Equipment Our computer-controlled treatment systems incorporate all necessary facets of a cooling tower or central chiller treatment system on a single, space-saving panel. System information is displayed on a LCD screen in one of four languages. Units come with lifetime warranty. Water Filters Sand media filters, strainer filters and full flow bag filters remove heavy-duty suspended solids from both cooling tower and chilled water systems. Toll-free (888) 828-7387 Tel (847) 966-2260 Ext. 2900 Fax (847) 966-9358 www.thermalcare.com Manufacturer reserves the right to change specifications or design without notice or obligation. Thermal Care is a registered trademark of MFRI, Inc. Printed in U.S.A. Form 7-260.2

RV Series Negative Pressure Temperature Controllers Installation, Operation and Maintenance Manual

Table of Contents FOREWORD... 1 INSTALLATION... 1 RECEIVING INSPECTION... 1 RIGGING, HANDLING, AND LOCATING EQUIPMENT... 1 ELECTRICAL POWER... 1 Table 1 - Voltage Utilization Range... 1 START-UP... 2 CONTROLLER OPERATION... 4 Figure 1 Control Panel... 4 Table 2 Microprocessor Fault Indication... 4 OPERATING KEYS... 5 ON... 5 OFF... 5 TEMPERATURE ADJUST... 5 INCREASE... 5 DECREASE... 5 TIMER ADJUST... 5 Table 3 Calender Day Values... 5 Table 4 Timer Day Values... 6 TIMER ON/OFF... 6 DEVIATION ALARM ADJUST... 6 TANK TEMPERATURE... 6 PASSWORD ENTRY... 6 OPERATING LIGHTS... 7 PUMP... 7 HEATING... 7 COOLING... 7 LOW LEVEL... 7 DEVIATION ALARM... 7 TIMER... 7 UNIT OPERATION... 7 ADJUSTING THE VACUUM... 8 DRAINING THE MOLD... 8 PREVENTIVE MAINTENANCE... 8 ONCE A WEEK... 8 ONCE A MONTH... 8 ONCE A YEAR... 8 TROUBLESHOOTING... 9 Table 5 Troubleshooting Chart... 9 CHARTS AND DRAWINGS... 10 Figure 2 Principle of Operation... 10 Figure 3 Microprocessor Control Board (Drawing 592)... 11 Figure 4 Pump Curves (SPA-1076)... 12 Figure 5 Cooling Capacity (SPA-1079)... 12 WARRANTY... 13

Foreword The intent of this manual is to serve as a guide for placing your positive/negative pressure temperature control unit in service and operating and maintaining it properly. This manual is supplemented as required to accommodate any special items that may have been provided for a specific application. The written information contained in this manual, as well as various drawings, are intended to be general in nature. The schematics included in this manual are typical only. We strive to maintain an accurate record of all equipment during the course of its useful life. While every effort is made to standardize the design features of these units, the various options may make it necessary to rearrange some of the components; therefore, some of the general drawings in this manual may differ from your specific unit. Specific references to current applicable codes, ordinances, and other local laws pertaining to the use and operation of this equipment are avoided due to their ever-changing nature. There is no substitute for common sense and good operating practices when placing any mechanical equipment into operation. We encourage all personnel to familiarize themselves with this manual's contents. Failure to do so may unnecessarily prolong equipment down time. These temperature control units must be installed in a well-ventilated area, especially if open flames are present. Failure to follow these instructions could result in a hazardous condition. It is recommended that good piping practices are followed and that the information in this manual is adhered to. We cannot be held responsible for liabilities created by substandard piping methods and installation practices external to the unit. We trust your equipment will have a long and useful life. If you should have any questions, please contact our Customer Service Department specifying the serial number and model number of the unit as indicated on the nameplate. Installation Receiving Inspection Each temperature control unit is skid mounted and crated to protect it during shipping. Before accepting delivery, check the crate for visible damage. If damage is evident, it should be properly documented on the delivery receipt and the crate should be immediately removed to allow for detailed inspection of the unit. Check for broken water lines, damaged controls, or any other major component torn loose from its mounting point. Any sign of damage should be recorded and a claim filed immediately with the shipping company. In order to expedite payment for damages it is important to record and document damage. An excellent way to do this is by taking pictures. Our Customer Service Department will provide assistance with the preparation and filing of your claims, including arranging for an estimate and quotation on repairs. Rigging, Handling, and Locating Equipment The temperature control unit has a base frame on casters that has been designed to allow the unit to be easily wheeled into position. If using a forklift or overhead crane proper rigging methods must be followed to prevent damage to components. Avoid impact loading caused by sudden jerking when lifting or lowering the unit. Use pads where abrasive surface contact is anticipated. The temperature control unit is designed for indoor use. If it is necessary to store the unit in an unheated indoor area when not in use, be sure that all water is drained or that an adequate amount of antifreeze is added to prevent freeze-up of the unit. In no case should this unit be installed or stored outdoors. A primary concern when designing your unit was serviceability, therefore, the unit should be located in an accessible area. Electrical Power All wiring must comply with local codes and the National Electric Code. Minimum circuit ampacities and other unit electrical data are on the unit nameplate and are shown in the Electrical Specification section at the back of this manual. A specific electrical schematic is shipped with the unit. Measure each leg of the main power supply voltage at the main power source. Voltage must be within the voltage utilization range given in Table 1. Table 1 - Voltage Utilization Range Rated Voltage Utilization Range 230 208 to 254 460 414 to 506 575 516 to 633 If the measured voltage on any leg is not within the specified range, notify the supplier and correct before operating the unit. Voltage imbalance must not exceed two percent. Excessive voltage imbalance between the phases of a three-phase system can cause motors to overheat and eventually fail. Voltage imbalance is determined using the following calculations: % Imbalance = (V avg V x ) x 100 / V avg V avg = (V 1 + V 2 + V 3 ) / 3 1

V x = phase with greatest difference from V avg For example, if the three measured voltages were 442, 460, and 454 volts, the average would be: (442 + 460 + 454) / 3 = 452 The percentage of imbalance is then: (452 442) x 100 / 452 = 2.2 % This exceeds the maximum allowable of 2%. A terminal block is provided for main power connection to the main power source. The main power source should be connected to the terminal block through an appropriate disconnect switch. A separate lug for grounding the unit is also provided in the main control panel. Electrical phase sequence must be checked at installation and prior to start-up. Operation of the temperature control unit with incorrect electrical phase sequencing will result in improper operation and can lead to mechanical damage. The phasing must be checked with a phase sequence meter prior to applying power. The proper sequence should read ABC on the meter. If the meter reads CBA, open the main power disconnect and switch two line leads on the line power terminal blocks (or the unit mounted disconnect). All components requiring electric power are wired in-phase at the factory. Do not interchange any load leads that are from the unit contactors or the motor terminals.! WARNING: It is imperative that L1-L2-L3 are connected in the A-B-C phase sequence to prevent equipment damage due to reverse rotation. Start-Up Every unit is factory set to perform in accordance with the standard operating specifications for that particular temperature control unit. Due to variables involved with different applications and different installations, minor adjustments may be required during the initial start-up to ensure proper operation. The following start-up procedure should be followed in sequence. If trouble is encountered during startup, the fault can usually be traced to one of the control or safety devices. This outline can be used as a checklist for the initial start-up and for subsequent start-ups if the unit is taken out of service for a prolonged period of time. 1. Assure the main power source is connected properly, that it matches the voltage shown on the nameplate of the unit, and that it is within the voltage utilization range given in Table 1. Electrical phase sequence must be checked at installation and prior to start-up. Operation of the temperature control unit with incorrect electrical phase sequencing will result in improper performance anc could lead to mechanical damage. The phasing must be checked with a phase sequence meter prior to applying power. The proper sequence should read ABC on the meter. If the meter reads CBA, open the main power disconnect and switch two line leads on the line power terminal blocks (or the unit mounted disconnect). All components requiring electric power are wired in-phase at the factory. Do not interchange any load leads that are from the unit contactors or the motor terminals. Once proper power connection and grounding have been confirmed, turn the main power on.! WARNING: The control panel and safeties are wired such that connecting the appropriate power source to the main terminal block energizes the entire electric circuitry of the unit. A control transformer has been factory wired to step down the incoming power to the control power. Electric power at the main disconnect should be shut off before opening access panels for repair or maintenance. The unit must be properly grounded in compliance with local and national codes.! WARNING: It is imperative that L1-L2-L3 are connected in the A-B-C phase sequence to prevent equipment damage due to reverse rotation. 2. The temperature control unit is provided with an inlet chilled water filter (shipped separately in crate). Install this in the inlet chilled water line before the line is connected to the unit. 3. Check to make sure that all process water piping connections are secure. 2

4. Check to make sure all cooling water piping connections are secure. Make sure sufficient cooling water flow and pressure are available and that all shut-off valves are open. 5. Turn on the control power by pressing the On button. The panel displays should now be illuminated. 6. If the display shows a decimal point in the first and last LED displays the unit is full of water and ready to operate. If the temperature control unit has never been filled or if the water level in the reservoir is insufficient, the digital displays with read FILL, the level LED will light and the unit will initiate an initial automatic fill cycle. This cycle will open the fill solenoid valve and allow the cooling source water to fill the reservoir. 9. Adjust the positive/negative flow through the mold by using the vacuum adjusting valve on top of the back panel. Start by fully closing this valve so that the injector makes a vacuum in the return line from process. At the leak, air is drawn into the circuit. The adjusting valve should be opened slowly to allow water to flow to the mold and pressurize the supply line. The leak will reappear as the pressure increases. At this point, the adjusting valve must be closed until the leak is eliminated. 10. Operate the unit for approximately 30 minutes. Check the unit for signs of leaks. Once proper flow and temperature are achieved, press the Off button. The unit is now ready to be placed into service. 7. After the reservoir is sufficiently full of water and the pump is operating, press the Temperature Adjustment key to display the current set point temperature. 8. Set the desired temperature using the Increase and Decrease buttons. When finished release all buttons. After five seconds the tank temperature is displayed and the new set point is stored. The unit will now activate the heaters and/or cooling solenoid valve to maintain set point temperture. 3

Controller Operation Figure 1 Control Panel Display Timer Adjust Temperature Adjust Increase Decrease Timer On/Off Cooling Light Heating 1 Light Pump Light Pump Overload Light Heating 2 Light Low Level Light Off On Tank Temperature Deviation Alarm Light Timer Activation Light ON Deviation Alarm Adjust OFF Password Entry Main Power Disconnect The temperature control unit includes a microprocessor controller designed to perform all control function from the front panel. When a key is depressed, a click will be felt. Unless instructed otherwise, only one key should be pressed at a time. Table 2 Microprocessor Fault Indication Fault Alarm Indicating LED Digital Display Indicator Tank Low Level Yes F I L L Internal Temperature Sensor Disconnected No A 2 Sensor Short Circuited (internal or external) No A 1 Actual Temperature Deviation Beyond Deviation Alarm Set Point Yes A X X. Pump Motor Overload Yes 4

Operating Keys On Depressing the On button will enable the control circuit. If the water level in the reservoir is below the level required to satisfy the low level sensor, the controller will initiate an initial fill sequence. During this sequence, the fill valve opens and will remain open until the proper water level is achieved. The automatic fill cycle has a four minute timer that will close the fill solenoid valve and stop the pump. This safety has been included in case there is a leak present that does not allow the reservoir to fill up. After the initial fill cycle is complete, the unit will automatically fill the tank if the level gets too low. If the fill valve remains open for more than 20 seconds, the unit will close the fill solenoid valve and shut off the pump. The display will show a "1" as the first digit followed by the tank temperature. Off Depressing the Off button will stop the pump and disable the control circuit.! I 0 CAUTION: Stopping the unit without cooling the water in the reservoir can lead to potential user injury during servicing of the unit. In order to allow the water in the reservoir to be cooled automatically during shut down, depress the Temperature Adjust button and the Password C button to initiate an automatic cool down cycle. The controller will open the cooling valve and keep it open until the temperature of the water in the reservoir is below 105 F (40 C). The automatic cool down cycle can be stopped at any time by depressing the Off button. Temperature Adjust Depressing the Temperature Adjust button will show the current set point temperature in the display. After depressing the Temperature Adjust button the set point temperature can be changed by using the Increase or Decrease buttons. Once the desired set point temperature is displayed release all buttons. After five seconds the display will return to the actual temperature and the new set point is activated. Increase Depressing the Increase button will adjust the set point, deviation alarm, and timer settings when those adjustment features are activated. Decrease Depressing the Decrease button decreases the value of the set point, deviation alarm, and timer settings when those adjustment features are activated. Timer Adjust Depressing the Timer Adjust button will activate the various timer adjustments. Setting Clock Depressing the Timer Adjust button once will show the current time value in the display. If the power to the unit has been disconnected, the clock is reset to 0000 hours (based on a 24 hour clock) and will begin keeping time from that point forward until reset. To adjust the time, use the Increase and Decrease buttons to set the current time. Once the current time is displayed release all buttons. After five seconds the display will return to the actual temperature and the new time is set. Setting Day Depressing the Timer Adjust button twice will show the current time value in the display. If the power to the unit has been disconnected, the day is reset to Monday (based on a 24 hour clock) and should be reset as required. To adjust the day, use the Increase and Decrease buttons to set the current daytime as follows. Table 3 Calender Day Values Day Display Value Monday 1000 Tuesday 2000 Wednesday 3000 Thursday 4000 Friday 5000 Saturday 6000 Sunday 7000 Once the current day is displayed release all buttons. After five seconds the display will return to the actual temperature and the new day is set. Setting Start Time Depressing the Timer Adjust button and then immediately depressing the Timer On/Off button once will reset the display to 0000. To adjust the start time, use the Increase and Decrease buttons to set the desired start time (based on a 24 hour clock). Once the start time is displayed release all buttons. After five seconds the display will return to the actual temperature and the new start time is set. Setting Stop Time Depressing the Timer Adjust button and then immediately depressing the Timer On/Off button twice will reset the display to 0000. To adjust the stop time, use the Increase and Decrease buttons to 5

set the desired stop time (based on a 24 hour clock). Once the stop time is displayed release all buttons. After five seconds the display will return to the actual temperature and the new stop time is set. Setting Days for Automatic Start/Stop Depressing the Timer Adjust button twice and then immediately depressing the Timer On/Off button once will reset the display to show the settings for Monday. When reviewing the settings for each day of the week, the first digit on the left of the display indicates the day of the week as follows. Table 4 Timer Day Values Day Display Value M onday 1 Tuesday 2 W ednesday 3 Thursday 4 Friday 5 S aturday 6 Sunday 7 The remaining three digits of the display indicate the activation status of that day. If these three digits display a decimal in the first and third digits, then that day is the day is scheduled for automatic start/stop. If these three digits display a decimal in the second and third digits, then that day is not scheduled for automatic start/stop. Example If Monday is scheduled for automatic start/stop the display will show 1 Example If Monda y is not scheduled for automatic start/stop the display will show 1 Timer On/Off To toggle the schedule status, press the On button once. The display will now change and indicated the change. Once the current setting is displayed, depress the Increase button to display the next day. Once all days have been programmed release all buttons. After five seconds the display will return to the actual temperature and the days for automatic start/stop are set. T Depressing the Timer On/Off button will activate or deactivate the automatic start/stop timer. If the far right hand display shows a decimal after the number displayed, then the automatic start/stop timer is activated. If no decimal is displayed the automatic start/stop timer is deactivated. Deviation Alarm Adjust Depressing the Deviation Alarm Adjust button will show the current deviation alarm set point in the display. The deviation alarm set point is the number of degrees the actual tank temperature must rise above the set point temperature before the alarm horn will activate. After depressing the Deviation Alarm Adjust the deviation alarm set point temperature can be changed by using the Increase or Decrease buttons. Once the desired deviation alarm set point is displayed release all buttons. After five seconds the display will return to the actual temperature and the new deviation alarm is set. Note: There is a time delay after initial start-up before the temperature deviation alarm becomes activate. The unit must be on with the pump running for 45 minutes before the alarm function is active. This time delay feature is designed to minimize the potential for unwanted alarms during initial startup as the unit brings the system up to operating temperature. Tank Temperature Depressing the Tank Temperature button will show the current tank temperature in the display. Password Entry A B C Depressing the Password Entry buttons will allow for secured access to the control program and will prevent unauthorized personnel from making changes. If a password has been entered, you will be required to enter the correct four letter password to make any adjustments to temperatures or timer functions. The password remains in memory even if the power is disconnected. Entering or Changing Password Depress the Off button and then immediately depress and hold the C Password Entry button for three seconds. The display will now show a C in the second display. Immediately enter a password consisting of any combination of four letters. The controller counts the number of letters entered and the display will show a 4 in the last display meaning all four password letters have been entered. Once the 4 appears release all buttons and press the Off button to store the password. Press the On button to restart the unit. The display will return to the actual temperature and the setting cannot be changed without the password. Deleting Password Depress the C and hold until the second display show C then press the Off button to delete the password. When the password has been deleted the first and last displays will show. To resume operation press the On button and the unit will 6

resume normal operation without password protection. Operating Lights There are eight operating lights, each located within a corresponding icon for that operational function. Pump There are two indicating lights in the Pump icon. The upper LED will be green when the pump is energized. The lower LED will be yellow when the pump motor overload has been tripped. Heating There are two indicating lights in the Heating icon. The upper LED will be green when heater 1 is energized. The lower LED will be green when heater 2 is energized. Cooling The LED in the Cooling icon will be green when the cooling solenoid valve is energized. Low Level The LED in the Low Level icon will be yellow when the water level in the reservoir is too low. Deviation Alarm The LED in the Deviation Alarm icon will be green when the Deviation Alarm is active. This LED will not be lighted if the Deviation Alarm has been turned off. Timer The LED in the Timer icon will be green when the Automatic Start/Stop Timer is active. This LED will not be lighted if the Automatic Start/Stop Timer has been turned off. Unit Operation The temperature control unit is designed to circulate water through a process and to precisely, automatically, and reliably maintain the water temperature at the selected set point temperature. The operating range of the unit is from 50 F (10 C) to 205 F (96 C). The unit is well suited or use with city water, water from chillers, cooling towers, or wells to provide the cooling water supply. The unit is a compact corrosion-proof unit with an integral stainless steel tank, stainless steel heating elements, cooling heat exchanger and an immersed stainless steel centrifugal pump without rotating seals. Water is pumped to the process through the discharge line and to the tank through the return line. The unit is an open system. The temperature in the tank is controlled by a microprocessor. The tank (process) temperature is displayed on the control panel LED's. During the heating cycle, the heating element is activated (if ordered) according to the heating requirement. During the cooling cycle, the solenoid valve opens and the cooling water is circulated through the heat exchanger until the proper temperature is reached. When the unit is connected to the power source, an LED connected to a level probe inside the tank will indicate whether the water has been filled to the correct level. The unit will automatically fill the tank to the correct level using the cooling water supply. When the unit is operating and there is too little water in the tank, the lamp lights, the pump stops and heating ceases. Once the tank is filled to the correct level, the unit will start automatically. The microprocessor controls the temperature and water level in the unit. The microprocessor includes alarms for low tank level and temperature deviation as well as a timer making automatic start/stop of the temperature controller possible. If a leak occurs in the mold or in the process, the built-in push-pull system permits stable temperature control without interrupting production. Through the use of the vacuum adjusting valve, the push-pull system makes it possible to supply pressure to the leak and vacuum from the leak back to the unit. If a leak occurs, the flow through the circuit should be arranged so that the leak is at the end of the water circuit. 7

Adjusting The Vacuum Adjust the positive/negative flow through the mold by using the vacuum adjusting valve on top of the back panel. Start by fully closing this valve so that the injector makes a vacuum in the return line from process. At the leak, air is drawn into the circuit. The adjusting valve should be opened slowly to allow water to flow to the mold and pressurize the supply line. The leak will reappear as the pressure increases. At this point, the adjusting valve must be closed until the leak is eliminated. Draining the Mold The temperature control unit is equipped with a specific program that can automatically cool to 105 F (40 C) before draining the mold. To initiate a mold drain sequence depress the Temperature Adjust button and then immediately depress the On button. The display will show E followed by the actual temperature in the tank. The cooling solenoid valve is energized and will remain energized unit the tank temperature drops to 105 F (40 C). When the tank temperature reached 105 F (40 C) the alarm horn will sound to signal the mold is ready for draining. Once the unit has cooled to 105 F (40 C), close the vacuum adjusting valve and remove the hose on the valve. A strong air current will automatically be sucked through the hoses and the mold. When the unit is finished draining, turn the unit off by depressing the Off button and remove the hoses. Preventive Maintenance One your positive/negative pressure temperature control unit has been placed into service, the following maintenance procedures should be adhered to as closely as possible. The importance of a properly established preventive maintenance program cannot be overemphasized. Taking the time to follow these simple procedures will result in substantially reduced downtime, reduce repair costs, and an extended useful lifetime for the unit. Any monetary costs of implementing these procedures will almost always more than pay for itself. Once a Week 1. Check all water line connections for signs of leaks. Replace or repair water lines and/or fittings as necessary. 2. Check to make sure the To Process temperature is maintained reasonably close to the Set Point temperature. If the temperature varies more than 5 F (3 C) from the set point temperature, there may be a problem with the unit. If this occurs, refer to the Troubleshooting Chart or contact our Customer Service Department. 3. Check the pump discharge pressure of the unit. If the discharge pressure starts to stray from the normal operating pressure this could be an indication that the leak in the mold has worsened or that there may be a problem with the unit. If this occurs, refer to the Troubleshooting Chart or contact our Customer Service Department. Once a Month Repeat items 1 through 3 as listed above and continue with the following. 4. With the main disconnect shut off and locked out, check the condition of electrical connections at all contactors, starters and controls. Check for loose or frayed wires. 5. Check the incoming voltage to make sure it is within 10% of the design voltage for the unit. 6. Check the amp draws to each leg of the pump and heaters to confirm that they are drawing the proper current. 7. Check the heat exchanger inlet strainer and clean debris out as necessary. Once a Year Repeat items 1 through 7 as listed above and continue with the following. 8. Carefully inspect the heat exchanger for signs of scale build-up and carefully clean and remove scale as necessary.! CAUTION: The amount of scale build-up is dependent upon the amount of cooling required for each process along with the quality of the cooling water supply. We have supplied the unit with a stainless steel heat exchanger to allow the use of strong lime scale removal chemicals (acids). We recommend you clean the heat exchanger thoroughly on a periodic basis, or after each job, to allow for the longest life and highest heat removal potential of the unit. If the heat exchanger becomes completely blocked, lime scale removal will be impossible. 8

Troubleshooting Table 5 Troubleshooting Chart Problem Possible Cause Remedy Main fuses blown Replace blown fuses The unit does not start after connection, tank filling, and pressing the On button Motor defective Reset tripped Contact factory Reset Motor buzzes after pressing the On button and overload trips Control circuit breaker tripped Voltage on two of the phases only Motor defective Reset Check incoming power supply, check and replace blown fuse Contact factory No water circulation, even though the pump is rotating Pump is rotating in the wrong direction Process water lines clogged Change two of the incoming power leads Clean lines Contactor defective Replace contactor The unit does not heat Thermostat defective Heating element defective Replace thermostat Replace heating element The unit does not cool Safety fuse defective Solenoid valve at Cooling Water In defective Cooling heat exchanger clogged Replace safety fuse Replace solenoid valve Clean coil The unit cooling all the time Thermostat defective Dirt in the cooling solenoid valve Thermostat defective Replace thermostat Take apart the valve, clean out, replace if required Replace thermostat Water comes out the overflow pipe Tank overfilled Dirt in the fill solenoid valve Level sensing probe dirty or defective Drain some water Take apart the valve, clean out, replace if required Clean probe, replace if required The unit does not fill the tank, level lamp is not on Level sensing probe dirty or defective Defective microprocessor Clean probe, replace if required Contact factory The unit does not fill the tank, level lamp is on Water supply not connected Defective fill solenoid valve Connect supply Replace if required 9

Charts and Drawings Figure 2 Principle of Operation 9 17 15 18 2 1 7 8 5 16 13 14 16 3 11 10 19 4 12 6 1. From mold 2. To mold 3. Cooling water in 4. Cooling water out 5. Pump 6. Tank 7. Level sensor 8. Temperature sensor 9. Microprocessor control 10. Heat exchanger 11. Heating element 12. Overflow pipe 13. Solenoid valve for water filling 14. Solenoid valve for cooling 15. Connection for external sensor 16. Check valve 17. Venturi 18. Adjusting valve, vacuum 19. Solenoid valve, mold draining 10

Figure 3 Microprocessor Control Board (Drawing 592) 11

Figure 4 Pump Curves (SPA-1076) 100 90 80 70 60 2 HP PUMP PRESSURE 50 40 30 1 1/2 HP 20 10 0-10 1 1/2 HP NEGATIVE PRESSURE 2 HP NEGATIVE PRESSURE -20 0 2 4 6 8 10 12 14 16 18 20 22 24 GALLONS PER MINUTE Figure 5 Cooling Capacity (SPA-1079) 70 60 50 BTU/H X 1000 40 30 20 10 0 20 30 40 50 60 70 80 90 100 T( F) = TANK TEMPERATURE LESS COOLING WATER TEMPERATURE 12