Installation Plan Professional Dishwasher PG 8061 Mat. no.: 09 838 370 en - US
Installation instruction Observe installation instructions when installing machine. This dishwasher is only suitable for commercial use. Installation Installation should only be carried out by authorized installers in accordance with valid regulations, relevant standards and health and safety codes! Condensate Only use commercial grade cabinetry in the vicinity of this commercial dishwasher as condensate may otherwise cause damage. Machine feet To ensure stability install the included floor bracket BBF-80 (Installation Instructions Mat.no.: 09788890) Electrical connection It is recommended to make electrical connection via a plug and socket so that electrical safety checks can be carried out easily. The socket must be accessible after machine installation. With a fixed installation, this must be via a main switch to be provided on site, which must completely isolate the machine from the power supply with a contact gap of at least 1/8 (3 mm). If necessary, an equipotential bond with good contact connection must be provided in accordance with all appropriate national and local regulations. Protection class IP21 Non-return device Connection to a drinking water supply is permitted without an additional non-return device. Steam condensor Steam condensor (DK) requires its own cold water connection. Use the supplied Y-adapter if only one cold water connection is available. External dosing system (optional) Connect up to two dosing systems at the rear panel for liquid cleaning agent and rinse aid. page 1 / 8 Installation plan PG 8061
Dimensions in drawings in inches & [mm] Installation plan PG 8061 page 2 / 8
Dimensions in drawings in inches & [mm] EL Electrical connection WW Hot water KW Cold water AW Drain water DS External dosing connection (optional) DK Steam condensor page 3 / 8 Installation plan PG 8061
Electrical connection (208 V) Voltage (default) 3 AC 208V 60 Hz 3 AC 208V 60 Hz Rated load 5.8 kw 5.8 kw Fuse rating 3 20 A 3 20 A Minimum cross-section 4 AWG 12 4 3.3 mm² Length of electrical cord (UL 921) with plug approx. 6 2 approx. 1.9 m Electrical connection NEMA L15-20 NEMA L15-20 Voltage (convertible) 2 AC 208V 60 Hz 2 AC 208V 60 Hz Rated load 5.8 kw 5.8 kw Fuse rating 2 30 A 2 30 A Minimum cross-section 3 AWG 10 3 5.2 mm² Length of electrical cord (UL 921) with plug approx. 6 2 approx. 1.9 m Electrical connection NEMA L6-30 NEMA L6-30 Electrical connection (240 V) Voltage (default) 3 AC 240V 60 Hz 3 AC 240V 60 Hz Rated load 5.8 kw 5.8 kw Fuse rating 3 20 A 3 20 A Minimum cross-section 4 AWG 12 4 3.3 mm² Length of electrical cord (UL 921) with plug approx. 6 2 approx. 1.9 m Electrical connection NEMA L15-20 NEMA L15-20 Voltage (convertible) 2 AC 240V 60 Hz 2 AC 240V 60 Hz Rated load 5.8 kw 5.8 kw Fuse rating 2 30 A 2 30 A Minimum cross-section 3 AWG 10 3 5.2 mm² Length of electrical cord (UL 921) with plug approx. 6 2 approx. 1.9 m Electrical connection NEMA L6-30 NEMA L6-30 Cold water connections* Max. temperature 68 F 20 C Max. water hardness 70 gpg 70 d Min. flow pressure 29 psi 200 kpa Min. flow pressure with extended water intake 5.8 psi 40 kpa Max. pressure 145 psi 1,000 kpa Throughput 2 gal/min 7.5 l/min Connection thread - on site (flat sealing) 3/4 Male Garden Hose Thread (USA: 11.5 NH) 3/4 Male Garden Hose Thread Length of connection hose (supplied) approx. 5 7 approx. 1.7 m Length of the steam condensor hose approx. 5 7 approx. 1.7 m * Two cold water connections required: use supplied Y-adapter if only one cold water connection is available. Installation plan PG 8061 page 4 / 8
Hot water connection Max. temperature 150 F 65 C Max. water hardness 73 gpg 70 dh Min. flow pressure 29 psi 200 kpa Min. flow pressure with extended water intake 5.8 psi 40 kpa Max. pressure 145 psi 1,000 kpa Throughput 2 gal/min 7.5 l/min Connection thread - on site (flat sealing) 3/4 Male Garden Hose Thread (USA: 11.5 NH) 3/4 Male Garden Hose Thread Length of connection hose (supplied) approx. 5 7 approx. 1.7 m Drain water Drain hose (internal diameter x wall thickness) 7/8 1/4 22 6 mm Length of Commercial Dishwasher drain hose 4 11 approx. 1.5 m Drain pump head height from floor level, max. 3 3 1 m Drain hose delivery, max. 4.2 gal/min 16 l/min On-site hose connector (external diameter x length) 7/8 1 3/16 22 30 mm External dosing system (optional) Connect up to 2 dosing systems at the rear panel for liquid cleaning agent and rinse aid. Machine feet Height adjustable 0-2 3/8 0-60 mm Foot diameter 1 3/8 35 mm Entry point into housing 8 M 8 M Heat dissipation to room Heat transfer by emission 1194 btu/h 0.35 kwh/h Load on removal 1365 btu/h 0.40 kwh/h page 5 / 8 Installation plan PG 8061
Machine data Unit height 32 5/16 820 mm Height including cover 32 7/8 835 mm Width 23 9/16 598 mm Depth 23 7/16 595 mm Door height 26 9/16 675 mm Net weight 154 lbs 70 kg Dynamic floor load 1.200 N 1.200 N Width including transport pallet 26 3/8 670 mm Depth including transport pallet 29 1/8 740 mm Height including transport pallet 36 1/4 920 mm Set-up conditions Ambient temperature 40-105 F 5-40 C Max. humidity 80% 80% Max. altitude above sea level 6560 2.000 m Installation plan PG 8061 page 6 / 8
U.S.A. Miele, Inc. National Headquarters 9 Independence Way Princton, NJ 08540 Phone: 800-991-9380 Fax: 609-419-4241 www.mieleusa.com Technical Service & Support Nationwide Phone: 800-991-9380 Fax: 800-220-1348 proservice@mieleusa.com All rights reserved! Date: 2015-06-08 Mat. no.: 09 838 370 page 7 / 8 Installation plan PG 8061