RWTM1-PT MY 2011 Terrain Rainwater PV rainwater systems
Terrain Rainwater Distinctive shapes Exceptiona performance Quaity product, innovation and outstanding service the combined promise that ensures every one of the Terrain five rainwater drainage systems wi surpass your requirements, whatever the instaation you re specifying. Large or sma; residentia or commercia; in the pubic sector or as part of an industria deveopment, in terms of both capacity and design aesthetics the Terrain range of products is impossibe to beat. Each Terrain system comprises fuy integrated gutter and downpipe assembies as we as outets for baconies and fat roofs, and incudes a the fittings and accessories needed for easy instaation. Features and benefits aptive seas in a gutter systems ombination cipping system for quick reiabe instaation Fixing ocations positioned outside the wet areas Expansion markings on LL gutter fixings Dry jointed spigot-socket downpipe system EN607/EN12200/EN1462 pproved rescent orniche Streamine Rapidfow Omega Outets True haf-round profie Idea for houses, smaer commercia buidings and offices. an drain roof areas up to 122m 2 with a singe downpipe. apacity per outet 2.54 itres/sec.* Square profie popuar, modern system suiting domestic houses, bungaows and conservatories. an drain roof areas up to 149m 2 with a singe downpipe. apacity per outet 3.11 itres/sec.* Large square profie high capacity system idea for commercia properties and arger houses. an drain roof areas up to 294m 2 with a singe downpipe. apacity per outet 6.11 itres/sec.* Deep eiptica profie high capacity system suiting a styes of property. Idea for arge roof areas or areas with higher than norma rainfa. an drain roof areas up to 266m 2 with a singe downpipe. apacity per outet 5.53 itres/sec.* Ogee profie Idea for the more distinctive house, aso suiting bungaows and conservatories. an drain roof areas up to 242m 2 with a singe downpipe. apacity per outet 5.04 itres/sec.* Roof and acony Outets Outets avaiabe for a fat roof and bacony structures and drain vent systems (For arge roof areas use Terrain Siphonics see separate cataogue). *For fu capacity specifications pease see System Panning on page 36. 2
ontents Lead Free PV Sustainabe Materias Terrain Drainage Products are 100% Lead Free. Pastics are among the most researched materias in the word and rapid technoogica and manufacturing deveopments made in recent years have aowed for continuous innovation. Terrain pioneered the deveopment of PV materia for the manufacturing of drainage pipes and fittings; we remain at the forefront of the industry across the gobe and are proud to be pioneering the industry once more with the deveopment of our LED-FREE systems to minimise the environmenta and heath risk impacts of the PV ife cyce. Utiising a ead-free materia composition contributes significanty to an environmentay friendy manufacturing process and gives a finished product that is fuy recycabe in accordance with Internationa Standards. For further information, pease refer to www.poypipe.com Terrain Rainwater System Seector 4 Roof & acony Outets 5-7 Rainwater Downpipes - Round 8-15 Rainwater Downpipes - Square 16-19 rescent Gutter System 20-22 orniche Gutter System 23-24 Streamine Gutter System 25-26 Rapidfow Gutter System 27-28 Omega Gutter System 29-30 ccessories 31-34 Fixing & onnections 35 System Panning 36-37 Genera Principes 38 Gutter Instaation 39-42 Downpipe Instaation 43-47 Roof & acony Outet Instaation 48 Roof Outet Instaation 49-51 Index 52-53 3
System Seector Gutters downpipe options 68mm round 62mm square 75mm square 82mm round 110mm round key component options stop end outet gutter ange 90 o gutter ange 120 o gutter ange 135 o gutter adaptors to 4 I spigot 4 I socket 4 Ogee I spigot 41/2 Ogee I socket Other PV-u Manufacturers Marey Deepfow coour grey back white rustic 2150 rescent 2250 orniche = 2350 Streamine * = 2450 Rapidfow = 2550 Omega = N other adaptors avaiabe on request bracket fixings avaiabe for side and top rafter fixing. Rise and fa drive in brackets aso avaiabe *daptor required =Specia fitting (Prefab) Downpipes gutter suitabiity 2150 rescent 2250 orniche 2350 Streamine 2450 Rapidfow 2550 Omega key component options 921/2 bend 1121/2 bend 1121/2 ong radius bend 135 bend singe branch doube branch wa offset pipe and fitting cip drive-in pipe cip adjustabe pipe cip coour grey back white rustic 68mm Round * = 62mm Square * 75mm Square = 82mm Round = 110mm Round acony & Roof Outets LONY OUTLETS downpipe options 68mm round 62mm square 75mm square 82mm round 110mm round appication baconies sma baconies porches garages fat roofs genera fat roofs combined fat roofs inverted surface finish compatibiity screed asphat minera fet singe ayer pastic genera roof finish 2172.3 screed finish * * 2174.3 asphat finish * * ROOF OUTLETS 2171.3 inverted roof outet 2171.34 vent pipe outet 2181.3 domed (sma) 2171.3 domed (arge) 2180.3 sma 2170.3 arge *With adaptor 2173.3.25 For arge roof areas (over 1000m2) use Terrain Siphonic Roof Drainage Systems, pease see separate cataogue. 4 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain Roof & acony Outets Terrain Roof Outets Outets Size (mm) D E F ode FLT ROOF OUTLET (LRGE) grey ony -To drain surface water from fat roofs Suitabe for most roof finishes 82 67 25 496 89 6 43 2170.3 110 58 25 406 117 6 43 2170.4 E D F Size (mm) D E F G ode DOMED ROOF OUTLET (LRGE) grey ony -To drain surface water from fat roofs Suitabe for most roof finishes 82 67 25 406 89 6 43 76 2171.3 110 58 25 406 117 6 43 76 2171.4 E D F G Size (mm) D E F ode FLT ROOF OUTLET (SMLL DIMETER) grey ony -To drain surface water from porches, garages and sma baconies. Suitabe for minera fet or singe ayer pastic roofs 50 6 16 25 178 61 3 2180.2 82 6 16 25 178 87 3 2180.3 E D F Size (mm) D E F ode DOMED ROOF OUTLET (SMLL DIMETER) grey ony - To drain surface water from porches, garages and sma baconies.suitabe for minera fet or singe ayer pastic roofs 50 48 16 25 178 61 3 2181.2 82 48 16 25 178 87 3 2181.3 E D F Size (mm) D E F G ode INVERTED ROOF OUTLET grey ony -To aow for drainage from two eves as required with inverted roof construction 110 60 25 406 117 6 43 260 2174.4 Size (mm) D E F G ode INVERTED ROOF OUTLET grey ony -Specia vented type for combined systems Suitabe for most roof finishes 110 58 25 406 117 6 43 371 2174.44 G E D F G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 5
Terrain Roof & acony Outets Terrain Roof Outets Outets Size (mm) D E* F G ode G E D F LONY OUTLET grey ony -For screed-finished baconies onnects to 82mm round downpipe can be reduced via socket daptors 2173.3.25 for 68mm round pipe 2273.3.23 for 62mm round pipe When used singy or at top of muti-storey buiding, use 9995.3 anking ap *Min size hoe for roof sab 82 48 27 59 170 94 13 68 2172.3 F G D Size (mm) D E* F G ode LONY OUTLET grey ony -For asphat-finished baconies Detais as 2172.3 *Min size hoe for roof sab 82 48 27 59 170 94 13 68 2174.3 Size (mm) L ode L SOKET DPTOR (82MM X 68MM) grey ony -To connect socket of 2172.3 and 2174.3 acony Outets to 68mm round downpipe 82/68 82 68 60 45 2173.3.25 Size (mm) L oour ode L SOKET DPTOR (82MM X 62MM) -To connect socket of 2172.3 and 2174.3 acony Outets to 62mm square downpipe 82/62 82 62 60 45 W G 2273.3.25 6 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain Roof Outets Outets oour ode SPRE GRID FOR DOMED ROOF OUTLET -for 2171 G 9980 oour ode SPRE GRID FOR FLT ROOF OUTLET -for 2170 G 9981 oour ode SPRE GRID FOR LONY OUTLET -for 2172 G 9990 oour ode P FOR LONY OUTLET -For use with 2173.3.25 and 2273.23 when used singy or at top of muti-storey buiding G 9995.3 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 7
Terrain Rainwater Downpipe Systems Rainwater Downpipe System - 68mm Size (mm) L T oour ode L 68MM DOWNPIPE - Pain ended engths 68 3.0m 1.8 W R G 2100.25.30 68 4.0m 1.8 W R G 2100.25.40 T 68 5.5m 1.8 W R G 2100.25.55 Size (mm) nge 1 2 oour ode 2 LONG RDIUS END - To change pipe direction: 112½ Prevents disocation of swan neck 68 112½ 54 55 W R 2101.25.112 1 Size (mm) oour ode STRIGHT OUPLER - For joining pipe engths. Fittings grooved to ocate downpipe bracket 68 8 W R G 2107.25 Size (mm) nge 1 2 oour ode 2 SHORT END -To change pipe direction: 92½ and 112½ bends To construct swan necks, use two 112½ bends 68 92½ 44 32 W R G 2108.25.92 1 68 112½ 32 22 W R G 2108.25.112 Size (mm) nge 1 2 3 oour ode 3 1 RNH -To join 68mm branch pipe to 68mm vertica pipe at an ange 90 and 112½ 68 90 29 54 54 W R G 2109.25.92 2 68 112½ 29 54 54 W R G 2109.25.112 8 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater Downpipe System - 68mm Size (mm) D E F G H ode RINWTER HED oours: W R G - To coect surface water at roof eve where gutters are not possibe 68 250 140 66 273 38 179 44 64 2111.25 E D F G H Size (mm) * oour ode PIPE ND FITTING RKET (DJUSTLE) -ows up to 10mm stand-off adjustment. * max = 73mm. 68 63 51 W G 2112.25.T Size (mm) oour ode PIPE ND FITTING RKET (DRIVE-IN) - Minimum stand-off distance (to back of pipe): 52mm 68 210 W 2112.25.D Size (mm) oour ode PIPE FITTING LIP - Minimum stand-off distance (to back of pipe): 32mm 68 66 90 110 W 2113.25 Size (mm) oour ode ENTRL FIXING LIP - Minimum stand-off distance (to back of pipe): 32mm 68 70 40 W R G 2113.25 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 9
Terrain Rainwater Downpipe Systems Rainwater Downpipe System - 68mm Size (mm) oour ode PIPE FITTING RKET - To secure downpipe to wa 68 66 131 114 W R G 2116.25 2 1 Size (mm) 1 2 oour ode ESS PIPE - To aow pipe ceaning or inspection 68 76 51 W R G 2137.25 10 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater Downpipe Systems - 82mm Size (mm) L oour ode 82MM DOWNPIPE - Pain ended engths 82 4.0m 2 W R 2100.3.40 L T Size (mm) L T(min) oour ode STRIGHT OUPLER (DOULE SOKET) - For joining pipe engths 82 92 3 W R 2107.3 L 10 75 Size (mm) nge 1 2 oour ode SWEPT END - To change pipe direction: 92½, 112½ and 135 as standard To construct swan necks, use two 112½ bends 2 10 82 92½ 70 72 W R 2101.3.92 82 112½ 43 75 W R 2101.3.112 82 135 16 22 W R 2101.3.135 Fabricated 1 75 Size (mm) nge 1 2 3 oour ode RNH (LL SOKET) -To join branch pipe to same size vertica pipe at an ange 92½, 112½ and 135 82 92½ 70 83 35 W R 2109.3.92 3 1 Fabricated 82 112½ 71 83 35 W R 2109.3.112 75 2 Size (mm) oour ode SHOE - To terminate rainwater downpipe discharging over guy 82 64 86 W R 2110.3 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 11
Terrain Rainwater Downpipe Systems Rainwater Downpipe Systems - 82mm D E F Size (mm) D E F G H ode RINWTER HED oours: W R G - To coect surface water at roof eve where gutters are not possibe 82 254 180 75 153 15 222 51 75 2111.3 G H Size (mm) D oour ode ONE-PIEE DOWNPIPE RKET - To support pipe and fittings stand-off distance (to back of pipe): 35mm 82 132 110 76 117 W R 143.3 D Size (mm) oour ode ESS PIPE - To aow pipe ceaning or inspection 82 41 39 120 W R 2137.3 12 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater Downpipe Systems - 110mm Size (mm) L T(min) oour ode 110MM DOWNPIPE - Pain ended engths 110 3.0m 2.44 W G 100.4.30 110 4.0m 2.44 W G 100.4.40 L T Size (mm) L 1 2 oour ode SWEPT END - To change pipe direction: 92½, 112½ and 135 as standard 2 110 92½ 75 83 W G 101.4.92 110 112½ 65 63 W G 101.4.112 110 135 30 30 W G 101.4.135 1 Size (mm) nge 1 2 oour ode 2 ESS END (DOULE SOKET) - To aow pipe ceaning or inspection 110 92½ 102 98 W G 103.4.92 1 Size (mm) nge 1 2 3 oour ode RNH (LL SOKET) -To join branch pipe to same size vertica pipe at an ange 92½ and 135 110 92½ 82 82 54 W G 104.4.92 3 1 110 135 25 137 137 W G 104.4.135 75 2 Size (mm) nge 1 2 3 oour ode ESS RNH - To aow pipe ceaning or inspection at junction of two pipes 110 92½ 99 96 50 W G 105.4.92 3 1 3 2 Size (mm) nge 1 2 oour ode SPIGOT END - To change pipe direction in imited-space situation 110 135 30 30 W G 107.4.135 1 2 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 13
Terrain Rainwater Downpipe Systems Rainwater Downpipe Systems - 110mm 1 Size (mm) nge 1 2 oour ode SPIGOT END (LONG TIL) - To change pipe direction in imited-space situation 2 110 92½ 57 197 W G 107.4.92 L Size (mm) L oour ode STRIGHT OUPLER - For joining pipe engths 110 102 3 W G 110.4 L Size (mm) L oour ode EXPNSION OUPLER - To create expansion joint when joining pipe engths in a sovent system 110 123 3 W G 111.4 Size (mm) oour ode SHOE - To terminate rainwater downpipe discharging over guy 110 77 86 W G 2110.4 14 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater Downpipe Systems - 110mm Size (mm) L oour ode ESS PIPE - To aow pipe ceaning or inspection L 110 216 115 W G 138.4 Size (mm) L oour ode L ESS PIPE - To aow pipe ceaning or inspection 110 216 166 W G 139.4 Size (mm) D oour ode ONE-PIEE DOWNPIPE RKET - To support pipe and fittings stand-off distance (to back of pipe): 35mm 110 146 124 91 151 W G 143.4 D G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 15
Terrain Rainwater Downpipe Systems Rainwater Downpipe Systems - 62mm Size (mm) L T(min) oour ode L DOWNPIPE - Pain ended engths 62 3.0m 1.8 W R G 2200.23.30 62 4.0m 1.8 W R G 2200.23.40 T 62 5.5m 1.8 W R G 2200.23.55 Size (mm) oour ode STRIGHT ONNETOR - For joining pipe engths 62 6 W R G 2207.23 Size (mm) nge 1 2 oour ode 2 END - To change pipe direction: 92½ and 112½ bends as standard To construct swan necks, use two 112½ bends 62 92½ 30 40 W R G 2208.23.92 1 62 112½ 24 32 W R G 2208.23.112 Size (mm) nge 1 2 3 oour ode 2 1 RNH - To join 62mm branch pipe to 62mm vertica pipe at an ange 112½ 62 112½ 20 49 87 W R G 2209.23.112 3 Size (mm) oour ode SHOE - To terminate rainwater downpipe discharging over guy 62 51 64 W R G 2210.23 1 2 Size (mm) 1 2 oour ode ESS PIPE - To aow pipe ceaning or inspection 62 150 300 W R 2237.23 16 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater Downpipe Systems - 62mm Size (mm) D E F G H ode RINWTER HED - To coect surface water at roof eve where gutters are not possibe. vaibe coours W R G E D F 62 274 128 44 295 38 179 44 58 2211.23 G H Size (mm) * oour ode PIPE ND FITTING RKET (DJUSTLE) - ows up to 32mm stand-off adjustment. * max = 70mm 62 42 102 126 W R G 2212.23 Size (mm) oour ode PIPE ND FITTING RKET (DJUSTLE) - ows up to 32mm stand-off adjustment 62 44 111 127 W R G 2213.23 Size (mm) oour ode LONG STND-OFF DOWNPIPE RKET - ows up to 32mm stand-off adjustment 62 62 93 109 W R G 2216.23 Size (mm) oour ode WLL OFFSET - To aow downpipe to accommodate wa pinth or other obstruction up to 57mm 110 57 22 W R G 2214.23 Size (mm) oour ode DPTOR (SQURE TO ROUND) - For connecting 62mm square to 68mm round down pipe 62/68 24 W R G 2215.23.25 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 17
Terrain Rainwater Downpipe Systems Streamine Rainwater Systems Downpipe - 75mm Size (mm) L T(min) oour ode L DOWNPIPE - Pain ended engths 75 4.0m 2 W R 2300.33.40 T Size (mm) oour ode STRIGHT ONNETOR - For joining pipe engths 75 8 W R 2307.33 Size (mm) nge 1 2 oour ode END- To change pipe direction: 112½ bends To construct swan necks, use two 112½ bends 1 75 112½ 29 36 W R 2308.33.112 Size (mm) Dimensions oour ode 2 3X3 SQ S/LINE END 75 Fabricated W R S2308.33.92 Size (mm) nge 1 2 3 oour ode RNH - To join 75mm branch pipe to 75mm vertica pipe at an ange 112½ 2 1 75 112½ 48 65 67 W R 2309.33.112 Size (mm) Dimensions oour ode 3 3X3 SQ S/LINE RNH 75 Fabricated W R S2309.33.92 18 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Streamine Rainwater Systems Downpipe - 75mm Size (mm) oour ode SHOE - To terminate rainwater downpipe discharging over guy 75 55 68 W R 2310.33 1 Size (mm) D E F G H ode RINWTER HED oours: W R - To coect surface water at roof eve where gutters are not possibe 75 253 180 75 153 15 234 45 70 2311.33 D H E G F Size (mm) oour ode PIPE ND FITTING RKET - Stand-off distance (to back of pipe): 13mm 75 50 124 140 W R 2313.33 Size (mm) oour ode WLL OFFSET - To aow downpipe to accommodate wa pinth or other obstruction up to 57mm 75 57 127 W R 2314.23 Size (mm) oour ode DPTOR (SQURE TO SQURE) - To adapt 2353.6.33 Running Outet/Pipe to discharge into 2200 Downpipe (62mm square) 75/62 16 W R 2315.33.23 Size (mm) 1 2 oour ode 1 ESS PIPE - To aow pipe ceaning or inspection 75 150 300 W R 2337.33 2 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 19
Terrain rescent System rescent Rainwater Systems - 110mm rescent Size (mm) T oour ode RESENT GUTTER - True haf round profie for maximum capacity Standard gutter ength 4m 110 110 55 2.2 W R G 2150.4.40 T Size (mm) oour ode JOINT RKET - For joining gutter engths 110 117 1.5 W R G 2151.4 Size (mm) oour ode SUPPORTING RKET - For supporting gutter engths, anges and stop-end outets 110 126 66 83 W R G 2152.4 D Size (mm) D oour ode RUNNING OUTLET - For connecting gutter run to downpipe 110 214 68 35 117 95 W R G 2153.4.25 Size (mm) nge oour ode GUTTER NGLE - To change gutter run direction: 90, 120 and 135 as standard 110 90 88 W R G 2154.4.90 110 120 60 W R G 2154.4.120 110 135 54 W R G 2154.4.135 110 156 96 W R G 2154.4.156 20 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
rescent Rainwater Systems - 110mm rescent Size (mm) oour ode SHORT STOP-END - To cap open gutter end 110 43 W R G 2155.4 Size (mm) oour ode INTERNL STOP-END - To cap open gutter end 110 33 2156.4 Size (mm) D oour ode STOP END OUTLET - To cap open gutter and connect gutter run to downpipe. 110 145 68 35 117 84 W R G 2157.4.25 D Size (mm) oour ode DPTOR TO OTHER PV-U GUTTERS - 2100 adaptor to a round rainwater systems 110 Sef cooured 2167 Size (mm) oour ode RESENT TO 4½ ST IRON SPIGOT - Socket adaptor to receive spigot end of haf-round cast iron gutter 110 57 22 G 2158.4.45 Size (mm) oour ode RESENT TO 4½ ST IRON SOKET - Spigot-end adaptor for inking into socket-end of haf-round cast iron gutter 110 57 19 G 2159.4.45 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 21
Terrain rescent System rescent Rainwater Systems - 110mm rescent Size (mm) oour ode RESENT TO 4½ OGEE ST IRON SPIGOT - Socket adaptor to receive spigot end of ogee cast iron gutter 110 62 22 W R G 2168.4.45 Size (mm) oour ode RESENT TO 4½ OGEE ST IRON SOKET - Spigot-end adaptor for inking into socket-end of ogee cast iron gutter 110 62 22 2169.4.45 22 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain orniche System orniche Rainwater Systems orniche Size (mm) T oour ode ORNIHE GUTTER - Rectiinear profie Standard gutter ength 4m 120 120 51 2.2 W R G 2250.5.40 T Size (mm) oour ode JOINT RKET - For joining gutter engths 120 114 1.4 W R G 2251.5 Size (mm) oour ode SUPPORT RKET - For supporting gutter engths, anges and stop-end outets 120 134 71 81 W R G 2252.5 Size (mm) D oour ode RUNNING OUTLET - For connecting gutter run to downpipe 110 193 62 44 105 75 W R G 2253.5.23 D G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 23
Terrain orniche System orniche Rainwater Systems orniche Size (mm) nge oour ode GUTTER NGLE - To change gutter run direction: 90, 120 and 135 as standard 120 90 95 W R G 2254.5.90 120 120 61 W R G 2254.5.120 120 135 55 W R G 2254.5.135 Size (mm) oour ode SHORT STOP-END - To cap open gutter end 120 43 W R G 2255.5 Size (mm) D oour ode STOP-END OUTLET - To cap open gutter end and connect gutter to downpipe D 120 106 62 44 106 65 W R G 2257.5.23 24 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain Streamine System Streamine Rainwater Systems - 137mm Streamine Size (mm) T oour ode STREMLINE GUTTER- High capacity rectiinear profie. Standard gutter ength 4m 137 137 73 2.5 W R 2350.6.40 T Size (mm) oour ode JOINT RKET - For joining gutter engths 137 149 2 W R 2351.6.12 Size (mm) oour ode SUPPORT RKET - For supporting gutter engths 137 153 82 115 W R 2352.6 Size (mm) oour ode OVERSLUNG RKET- Leaves front face of gutter uncuttered for improved appearance 137 162 82 114 W R 2352.150 Size (mm) D oour ode RUNNING OUTLET - For connecting gutter run to downpipe To 75mm square downpipe 137 281 75 45 157 133 W R 2353.6.33 To 82mm round downpipe 137 281 75 50 174 133 W R 2353.6.3 D To 110mm round downpipe 137 281 103 50 157 133 W R 2353.6.4 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 25
Terrain Streamine System Streamine Rainwater Systems - 137mm Streamine Size (mm) nge oour ode GUTTER NGLE - To change gutter run direction: 90 and 135 as standard 137 90 85 W R 2354.6.90 137 135 40 W R 2354.6.135 Size (mm) oour ode SHORT STOP-END - To cap open gutter end 137 71 W R 2355.6 Size (mm) Dimensions oour ode STREMLINE STOP END OUTLET LEFT HND 137 Fabricated W R 2357.6.33WLH Size (mm) Dimensions oour ode STREMLINE STOP END OUTLET RIGHT HND 137 Fabricated W R 2357.6.33WRH D Size (mm) D oour ode SREWED OUTLET DPTOR - Spigot outet to be set into gutter base ows connection to 75mm square downpipe. *Use 75mm hoe cutter 75 68 45 70 75 W R 2368.3 26 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain Rapidfow System Rapidfow Rainwater Systems - 131mm Rapidfow Size (mm) T oour ode RPIDFLOW GUTTER- Deep eiptica profie. Standard gutter ength 4m 131 131 82 2.5 W R 2450.5.40 T Size (mm) oour ode JOINT RKET - For joining gutter engths 131 115 1.5 W R 2451.5 Size (mm) oour ode SUPPORT RKET- For supporting gutter engths, anges and stop-end outets 131 145 76 115 W R 2452.5 Size (mm) D oour ode RUNNING OUTLET - For connecting gutter run to downpipe To 68mm round downpipe 131 266 68 35 188 144 W R 2453.5.25 D To 82mm round downpipe 131 266 82 45 188 144 W R 2453.5.3 Size (mm) nge oour ode GUTTER NGLE - To change gutter run direction: 90 and 135 as standard 131 90 109 W R 2454.5.90 131 135 63 W R 2454.5.135 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 27
Terrain Rapidfow System Rapidfow Rainwater Systems - 131mm Size (mm) oour ode SHORT STOP-END - To cap open gutter end Rapidfow 131 53 W R 2455.5 Size (mm) D oour ode STOP-END OUTLET - To cap open gutter end and connect gutter to 68mm round downpipe 131 183 188 35 68 99 W R 2457.5.25 D STOP-END OUTLET - To cap open gutter end and connect gutter to 82mm round downpipe 131 183 188 35 68 99 W R 2457.5.3 Size (mm) oour ode DPTOR LIP TO OTHER PV-U GUTTERS - 2400 adaptor to a deepfow round systems 131 Sef cooured 2467 28 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Terrain Omega System Omega Rainwater Systems - 122mm Omega Size (mm) T oour ode OMEG GUTTER- Deep ogee profie. Standard gutter ength 4m 122 122 72 2.5 W R 2550.5.40 T Size (mm) oour ode JOINT RKET - For joining gutter engths 122 137 2.0 W R 2551.5 Size (mm) oour ode UNDERSLUNG SUPPORT RKET - For supporting gutter engths 122 138 70 104 W R 2552.5 2552.5 is for use with Rafter brackets 122 138 70 104 W R 2552.5 Size (mm) oour ode OVERSLUNG SUPPORT RKET- Leaves front face of gutter uncuttered for improved appearance 122 142 70 76 W R 2552.5.150 Size (mm) D oour ode RUNNING OUTLET - For connecting gutter run to 68mm or 62mm downpipe 122 261 62 41 156 125 W R 2553.5.25 D G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 29
Terrain Omega System Omega Rainwater Systems - 122mm Omega Size (mm) nge oour ode INTERNL GUTTER NGLE - To change gutter run direction: 90 and 135 as standard 122 90 93 W R 2554.5.90I 122 135 27 W R 2554.5.135I Size (mm) nge oour ode EXTERNL GUTTER NGLE - To change gutter run direction: 90 & 135 as standard 122 90 67 W R 2554.5.90E 122 135 23 W R 2554.5.135E Size (mm) oour ode SHORT STOP-END (EXTERNL) - To cap open gutter end at externa roofine boundaries. Left (L) and Right (R) hand versions are avaiabe 122 83 75 W R 2555.5L 122 83 75 W R 2555.5R Size (mm) oour ode INTERNL STOP-END - To cap open fitting end and at interna roofine boundaries. Left (L) and Right (R) hand versions are avaiabe 122 120 W R 2556.5L 122 120 W R 2556.5R D Size (mm) D oour ode STOP-END OUTLET - To cap open gutter end and connect gutter to 68mm or 62mm downpipe. Left (L) and Right (R) hand versions are avaiabe 122 120 62 41 156 W R 2557.5.25L 122 120 62 41 156 W R 2557.5.25R 30 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater ccessories Rainwater ccessories Size (mm) (min) (max) D oour ode SIDE RFTER RKET (DJUSTLE) - For connecting gutter support bracket and strap to side of open rafter end. For 2100 rescent and 2200 orniche 91 157 13 53 19 Sef 2160 D For 2300 Streamine, 2400 Rapidfow and 2500 Omega 115 155 13 110 19 Sef 2360 Size (mm) (min) (max) oour ode TOP RFTER RKET (DJUSTLE) - For connecting gutter support bracket and strap to top edge of open rafter end. For 2100 rescent and 2200 orniche 86 250 26 79 Sef 2161 For 2300 Streamine, 2400 Rapidfow and 2500 Omega 115 250 26 104 Sef 2361 Size (mm) D E oour ode RISE ND FLL RKET (DJUSTLE) DRIVE IN RKET - To support gutter support bracket and strap where no fascia or rafters are avaiabe. For 2100 rescent and 2200 orniche E D 260 130 50 62 43 Sef 2162 For 2300 Streamine, 2400 Rapidfow and 2500 Omega 275 152 83 93 57 Sef 2362 (min) (max) (min) (max) D (min) D (max) E F F (min) (max) SUPPORT STRP (LL SYSTEMS) - Provides support for gutter fittings (running outets and joint brackets) where fitting to rafters is required - Sef ooured G ode 310 266 281 235 241 193 212 149 115 127 25 2265 G D E F G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 31
Rainwater ccessories Rainwater ccessories oour ode SPER LOK (STRIGHT) - To increase stand-off distance of gutter support bracket. For 2100 rescent and 2200 orniche 76 16 2166 oour ode SPER LOK (TPERED) - To compensate for 22 ½ of soping fascia. For 2100 rescent and 2200 orniche 76 33 2166.22 oour ode GUTTER SEL - Repacement seas for gutter fittings at connection points for 2100 rescent 9911 for 2200 orniche 9922 for 2300 Streamine and 2500 Omega 9933 for 2400 Rapidfow 9944 Size (mm) oour ode GUTTER OUTLET GURD - For pacement over outet aperture to reduce risk of downpipe bockages by eaves, other debris etc. Suitabe for 68mm round and 62mm square outets 122 9915.25 Size (mm) oour ode DPTOR TO OTHER PV-U GUTTERS - 2150 adaptor to a round rainwater systems 110 Sef 2167 32 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Rainwater ccessories Size (mm) oour ode DPTOR LIP TO OTHER PV-U GUTTERS - 2450 adaptor to a deepfow round systems 131 Sef 2467 Size (mm) L oour ode DPTOR TO UNDERGROUND DRIN - For connecting 68mm downpipe to 82mm underground drain. 68/82 54 3DW25 L Size (mm) L oour ode DPTOR TO UNDERGROUND DRIN - For connecting 68mm downpipe to 110mm underground drain 68/110 54 10 4DW25 L Size (mm) L oour ode DPTOR TO UNDERGROUND DRIN - onnects 62mm or 75mm downpipe to 110mm underground drain. L 62/110 54 4DW23 Size (mm) L oour ode DPTOR TO UNDERGROUND DRIN - onnects 82mm downpipe to 110mm underground drain L 82/110 54 4DW3 Size (mm) L oour ode PIPE DPTOR 4 X 3 / 75MM SQ L 75/110 54 4DW33 G - Grey - ack W - White R - Rustic rown dimensions in mm uness otherwise stated 33
Rainwater ccessories Rainwater ccessories Size (mm) oour ode UNIVERSL RINWTER DPTOR - onnects 68mm or 62mm square downpipe to 110mm underground drain. Fits both pipe end and socket. Not for connection to fou drainage 68/110 110 102 4D76 Size (m) Description ode LIQUID WELD - 125m Liquid Wed Tin s6209 9100.125 250m Liquid Wed Tin s6209 9100.250 500m Liquid Wed Tin s6209 9100.500 Size (m) Description ode SOLVENT LENING FLUID - 125m Sovent eaning Fuid 9101.125 250m Sovent eaning Fuid 9101.250 Size (m) Description ode LURINT - For ubricating sea rings on expansion fittings 250m Terrain Siicone Lubricant 9136.250 500m Terrain Soube Lubricant 9136.500 34 dimensions in mm uness otherwise stated G - Grey - ack W - White R - Rustic rown
Fixing & onnections Fixing centres and expansion points Therma movement When fixing gutter, aowance must be made for therma movement and a Terrain outets, anges and joint brackets are engraved with the appropriate expansion gaps. It is important that the gutter is correcty fitted into these fittings taking due care to pace the cut end of the gutter on the ine marked. It is important that the expansion gaps are maintained when gutter is fitted and must not be spaced to exceed 4 metres/13ft centres. In the case of dry jointing downpipe each fitting cip has a sight hoe provided on the front of it. (2113.25, 2216.23 and the 82mm and 110mm fitting cips do not have sight hoes.) The purpose of the sight hoes is to aow sight of the top of the pipe being fitted from beow. When this pipe end obscures haf of the aperture you have the correct expansion gap. The maximum distance between expansion joints shoud not exceed 5.5 metres/18ft. For roof outets ppication range: ppicabe to: 82mm and 110mm round pipework used with roof outets. Maximum distance between: Vertica pipe fixing cips: Pipe expansion joints: 110 Downpipe 82 mm Downpipe mm 2 metres 4 metres NOTE: nchor expansion coupings with 140 Pipe Fixing ip to prevent therma expansion upthrust from rupturing joint between roof outet and finish ppicabe to: a Terrain gutter systems and downpipe assembies Maximum distance between: Gutter support brackets*: Gutter expansion joints: Pipe fixing cips: Pipe expansion joints: 1 metre* 4 metres 2 metres 5.5 metres *NOTE: Support centres for gutters subject to risk of heavy snow fa shoud be reduced to 800mm (max). Fig. 2 11 mm gap Engraved ine For roof outets onnector Maximum 4.0 metres between expansion Joints 11mm gap Sight Mouded 10mm expansion gap Pipe & Fitting ip Maximum 1 metre Fig. 3 10 mm expansion gap Maximum 2.0 m pipe Fig. 1 supports Maximum 5.5 m between expansion joints Fit expansion couping immediatey under roof outet 111 Expansion couping nchor couping with 140 Pipe Fixing ip to prevent upthrust due to therma expansion from breaking joint between outet and roof finish 12mm expansion gap 140 Pipe Fixing ip Maximum 2.0m between supports Maximum 4.0m between expansion 12mm Expansion couping Fig. 4 dimensions in mm uness otherwise stated 35
System Panning Design principes Sizing of rainwater instaations There is an approved S EN method for the cacuation of roof fow oad, and the foowing genera guideines and assumptions on sizing of rainwater instaations are based on this. For detaied guidance on a particuar project, pease refer to S EN 12056-3:2000 Gravity Drainage Systems Inside uidings Roof Drainage, Layout and acuations, or contact Terrain Technica Services on 01622 795200. Rainfa In the UK, it is generay satisfactory for eaves gutters to be designed for a rainfa intensity of 75mm/hr. The predicted frequency of storms producing intensities of 75mm/hr is ow, with just one 2 minute duration fa of such intensity anticipated each year. good factor of safety is therefore buit into any design using these vaues. However, when designing for cosed areas such as ightwes, fat roofs or simiar the rainfa intensity vaue aowed for shoud be increased. gain, pease refer to S EN 12056-3:2000. Snow The foowing shoud be taken into account when designing guttering systems when snow oads are common or ikey. ritish Standards S EN 12056-3:2000 Section N4 states: Gutter designed for rainfa wi have adequate fow capacity for the remova of meting snow. However, gutters and outets can become bocked by frozen snow but this can be avoided by the use of trace heating or snow boards. Snow guards may be fitted to the eaves of a pitched roof where siding snow may cause injury to peope or damage to structures beow. Depending upon what is at risk, snow guards can be necessary for roof pitches up to 60 o from the horizonta and they need not be higher than 300mm for most situations. The fixings shoud be strong enough to withstand the forces cacuated in accordance with S 639903. Section 7.2.2 states: In areas where snow ies on roofs, the front edge of the gutter shoud not be higher than the projected ine of the roof, uness snow guards or other precautions are used. Terrain recommends that in designs where snow is ikey, the gutter support brackets shoud be fixed at maximum of 800mm centres. In areas of high risk of snow Terrain recommends the use of snow guards or other protection. Roof Fow Load: How to cacuate it There are two factors to consider when cacuating fow. Firsty the area to be drained, or effective roof area ; and the intensity of rainfa. For the intensity of rainfa you shoud assume 75mm/hr except for encosed areas such as ightwes and fat roofs. Effective Roof rea Effective Roof rea can be cacuated using the foowing formua, as iustrated in Fig.5. ER(m2) =(W + H/2) x L (Fig.5) KEY: ER = Effective Roof rea (square metres) W = horizonta distance from eaves to point directy beow ridge H = vertica rise between eaves and ridge (metres) L = gutter ength (metres) acuating the actua fow Once you have cacuated the ER, for 75mm/hr rainfa intensity FLOW (itres/second) = ER (m2) x 0.0208 For other rainfa intensities FLOW = ER (m2) x rainfa intensity (mm/hr)/3600 = itres/second Fig. 5 H 90 o W L Wind There is no requirement to aow for the effect of wind when designing a rainwater system for fat roofs or roofs protected from the wind by adjacent buidings. However, the wind and the roof sope can have the effect of increasing the roof fow oad for unprotected pitched roofs. This is aowed for in the S EN 12056-3:2000 cacuation method by adding haf the rise to the roof span. 36 dimensions in mm uness otherwise stated
Fow oad cacuations Position Downpipe Size/Type (mm) 2100 rescent Leve Gutter rea (m 2 ) Fow (/s) Gutter 1:350 fa rea (m 2 ) Fow (/s) 68 round 46 0.96 61 1.27 2200 orniche 62 square 53 1.10 72 1.50 2300 Streamine 75 Square 82 and 100 round 123 2.56 147 3.06 2400 Rapidfow 68 & 82 round 105 2.19 133 2.77 2500 Omega 62 square 68 round 96 2.00 121 2.52 Roof outets fow data The fow rates isted have been estabished by independent testing carried out by the Rainwater Drainage Design ompany using faciities at the Hydrauics aboratory of Saford University. Roof outet Size Fow capacity itres/sec Head of water at outet part no. 30mm 50mm 100mm 2180.2 50 0.88 1.18 1.78 2180.3 82 2.12 2.52 3.21 2181.2 50 2.00 2.27 2.69 2181.3 82 2.10 4.89 7.22 2170.3 82 9.18 11.08 13.67 2170.4 110 9.29 14.11 18.22 2171.3 82 4.94 9.24 16.64 2171.4 110 5.17 9.95 24.18 Position 2100 rescent 68 round 37 0.77 49 1.02 2200 orniche 62 square 42 0.87 58 1.21 2300 Streamine 75 Square 82 and 100 round 103 2.14 123 2.56 2400 Rapidfow 68 & 82 round 86 1.79 109 2.27 2500 Omega 62 square 68 round 77 1.60 97 2.02 Note: Figures based on 75mm/hr rainfa intensity Position 2100 rescent 68 round 92 1.91 122 2.54 2200 orniche 62 square 113 2.36 149 3.11 2300 Streamine 75 Square 241 5.02 286 5.96 82 round 242 5.04 286 5.96 110 round 242 5.04 294 6.11 2400 Rapidfow 68 & 82 round 210 4.38 266 5.53 2500 Omega 62 square 68 round 192 4.00 242 5.04 Roof outet fow oad: cacuation method For a fat roof (i.e. a roof with a pitch ess than 10 ), the effective roof area = the pan area of the reevant part of the roof. To cacuate fow in itres/second for 75mm/hr rainfa intensity: firsty measure pan area of roof served by each outet (square metres) and then mutipy area by 0.0208 to obtain fow (itres/ second) NOTE: See ode of Practice S EN 12056-3:2000 for fu detais dimensions in mm uness otherwise stated 37
Genera Principes Good Site Practice - Handing Take a reasonabe care when handing PV-u, particuary in very cod conditions. Load and unoad oose pipes by hand. In case of mechanica handing, avoid the use of chains and hooks. On site storage Stack pipe engths: either on a fat base or on eve ground or on 75mm x 75mm timber at 1m maximum centres. Provide side support with 75mm wide battens at 1m centres (see Fig.6). Maximum stack: seven ayers high. Ideay, stacks shoud contain one diameter pipe size ony. Where this is not possibe, stack argest diameter pipes at base of stack. Sma pipes may be nested inside arger pipes. If stored in the open for ong periods or exposed to strong sunight, cover the stack with opaque sheeting. Store fittings under cover. Do not remove from cartons or packaging unti required. Gutters shoud be kept under simiar storage conditions, but additiona care shoud be taken to protect the profie. Store sovent cement and ceaning fuid in a coo pace out of direct sunight and away from any heat source. 1m Maximum entres 110mm 160mm with 110mm Inserted 75mm Minimum Width 1m Maximum entres Fig. 6 38 dimensions in mm uness otherwise stated
Gutter Instaation Gutter Instaation Genera principe ppicabe to: a Terrain gutter systems onnecting to other gutter systems ppication Range Lock back cips of fittings in position and screw fitting to fascia where appicabe Locate back of gutter under rear cip ensuring that the expansion gap is correct (see page 2) Pu front of gutter down and push front cip into position. To reease gutter for adjustment, pu on tab at front of fitting rescent Rapidfow ppicabe to: 2100 RESENT and 2400 RPIDFLOW Gutter daptor ips (2167.4 for 2100 RESENT, 2467.5 for 2400 RPIDFLOW) permit connection between Terrain systems and PV-u guttering of a simiar design from other manufacturers 1. Lock back cips in position and screw fitting to fascia 2. Locate back of gutter under rear cip. Remove front ocking cip from the side of Terrain fitting which is to take the connection, UT DO NOT DISRD Lay the other manufacturer s gutter into the fitting, ensuring that it sits correcty within the fitting and that the expansion gap is correct Insert one end of the daptor ip under the back ocking cip Hoding the adaptor cip in position, re-insert the front ocking cip heck that the gutter is fuy seated within the fixing cip Push the front of the daptor ip down onto the ocking cip seat Pu to reease gutter. 3. Pu front of gutter down and push front cip into position. To reease gutter for adjustment, pu on tab as shown. Push to ocate gutter in position. Fig. 7 Fig. 8 2400 RPIDFLOW system dimensions in mm uness otherwise stated 39
Gutter Instaation Fixing principes Secure fixing: screw specification ppicabe to: a Terrain gutter systems Terrain gutter systems are designed to withstand maximum anticipated oading (e.g. heavy snow) without breaking ny method of fixing the gutter system to the buiding fabric MUST be equay capabe of bearing such oading ssuming fixing to nomina 25mm thick softwood, fascia screws shoud be: Size: No.10 roundhead* zinc-pated Length: penetrating wood by minimum 19mm *Some fittings are manufactured with countersunk hoes (Omega). In such cases countersunk screws may be used Fixing methods ppicabe to: a Terrain gutter systems Fig.9a 2200 ORNIHE system Lugs Generay, Terrain gutter fittings (brackets, outets, anges) are designed with: EITHER integra fixing ugs (Fig.9a) OR recess(es) (Fig.9b) which accept a standard support bracket IMPORTNT NOTE: Whichever method is used, LL fittings must be anchored In some cases, Terrain gutter fittings are designed with screw fixing hoes behind the sea, eg gutter ange 2354.6.90. If it is not possibe to secure gutter anges through the screw fixing hoes, then support brackets must be fitted to the gutter within 150mm of the ange on both sides Spacer bocks ppication range: ppicabe to: 2100 RESENT and 2200 ORNIHE systems Designed to enabe 2100 and 2200 systems to accommodate arge tie overhangs, pacing the gutter centray beneath the tie edge. voids the need to use a arger gutter system. 2166 Spacer (rectanguar): Steps out gutters by 16mm 2166.22 Spacer (trianguar): ows gutters to be fixed to 221/2 soping fascias rescent orniche Screw fix spacer to fascia through fixing hoes provided Fix bracket THROUGH spacer, soidy into fascia Recess Fig.9b Screw hoes for interna ange behind sea 150mm 150mm Fig.10 Fig.11 40 dimensions in mm uness otherwise stated
Fixing rackets Fixing adjustabe rafter bracket ppicabe to: a Terrain gutter systems For fixing gutter systems to open-ended rafters where no fascia exists NOTE: Ony suitabe for rafters in sound condition hoice of brackets (a adjustabe): Side (2160 and 2360) Top (2161 and 2361) () Fixing to rafter using (minimum) 2 x No.10 roundhead zinc-pated screws Support bracket secured by singe bot Fig.12 Pegs on rafter bracket ocate in screw hoes of support bracket System djustment Range () 2100, 2200 65mm 2300, 2400, 2500 75mm Support Strap Support Strap Gutter fitting support strap Rafter racket ppicabe to: a Terrain gutter systems For use with joint brackets and running outets when used with any rafter bracket Discard PV-u back pate from rafter bracket: retain nut and bot to fix support strap to brackets Studs 2265 Support Strap Studs prevent support strap from twisting Fig.13 dimensions in mm uness otherwise stated 41
Gutter Instaation Drive-in rackets Drive-in brackets Fixing drive-in brackets ppicabe to: a Terrain gutter systems For fixing gutters where no fascia board or rafters exist Standard version: 2162 (for 2100 RESENT and 2200 ORNIHE systems) Heavy duty version: 2362 (for 2300 STREMLINE, 2400 RPIDFLOW and 2500 OMEG systems) Drive spike into mortar at appropriate height to aow fitting of gutter support bracket (or dri suitabe hoe and mortar spike in) Support bracket hed in position by nut and bot djust height by sackening ocking nuts on threaded stud Fig.14 NOTE: If used on corbeed brickwork, ensure sufficient penetration of spike into mortar to support potentia gutter oading 42 dimensions in mm uness otherwise stated
Downpipe Instaation Offsets Form an offset (or swan neck ) using 2 x 112.5 standard bends and a cut ength of pain ended pipe Sma offsets ppication range: Downpipe 62 mm Downpipe 75 mm ppicabe to: 62mm and 75mm square downpipe systems For 62mm square downpipe, 2214.23 Wa Offset provides 25mm offset For 75mm square downpipe, 2314.33 Wa Offset provides 57mm offset Fig.15 djustabe Pipe ips djustabe pipe fitting cip (2112.25.T) ppication range: djustabe pipe fitting cip (2212.23.T) ppication range: rescent Rapidfow orniche Omega Downpipe 62 mm ppicabe to: 2100 RESENT, 2400 RPIDFLOW and 2500 Omega, 68mm round downpipe Omega Downpipe 68 mm Screw back pate to wa using No.10 roundhead screws Snap cip body around pipe or fitting. If around fitting, ensure it is ocated in the mouded groove Locate assemby over back pate and secure with nut and screw provided at required distance from wa ppicabe to: 2200 ORNIHE and 2500 OMEG, 62mm square downpipe Screw back pate to wa using No.10 roundhead screws Locate body over back pate. Ensure fixing nuts and screws are oosey fitted onto cip body (the screw thread shoud not fuy penetrate the nut) Grip the screw heads firmy and ocate onto the back pate Tighten fixing screws at required distance from wa Fig.16 djustment Range Fig.17 min max min max 63 73 63 73 dimensions in mm uness otherwise stated 43
Downpipe Instaation Outet Guard Gutter outet guard (9915.25) ppication range: 62 Downpipe 68 mm Downpipe mm ppicabe to: 68mm round and 62mm square downpipe Fexibe poyethyene fitting designed to prevent eaves etc. entering the downpipe Push-fit into Stop End or Running Outet Fig.18 Rainwater Shoes Fixing and ocking rainwater shoes ppication range: Downpipe 68 mm Retaining groove ppicabe to: 68mm round downpipe systems Locate the mouded nib on retaining grooves of shoes in one of the five retaining notches on 2112 or 2113 Fixing ip Five different positions are possibe. Each ensures both shoe and pipe above it are fuy supported Nib Fig.17 44 dimensions in mm uness otherwise stated
Rainwater Heads ppicabe to: a Terrain Downpipes Direct push-fit connection at correct distance from wa (Fig.20a) 2111.25 to suit 68mm round 2211.23 to suit 62mm square 2111.3 to suit 82mm round 2111.4 to suit 110mm round Requires 25mm Offset end F2314.33.25 for connection to 75mm square downpipe at correct distance from wa (Fig.20b) Fig.20a Fig.20b 2311.33 to suit 75mm square onnection to uried Pipes onnection to buried pipes ppication range: 75 Downpipe 68 mm Downpipe 68 mm Downpipe mm Rainwater pipe EPDM adaptor Socket 110 mm UPV ppicabe to: 68mm round and 62mm or 75mm square downpipe systems Use EPDM rubber drain adaptors to connect downpipes to 82mm and 110mm buried drains Rainwater pipe EPDM adaptor Drain Fig.21 Outet daptor Screwed outet adaptor (2368) ppication range: 62 Downpipe 68 mm Downpipe mm ppicabe to: 2300 Streamine with 75mm square downpipe Enabes downpipe to be positioned anywhere aong a gutter ength Using Terrain Hoe utter 2105.3 dri 76mm diameter hoe in centre of base of gutter Unscrew the two parts of the adaptor and push top part with screw thread through hoe in gutter outet guard Screw the two parts of the adaptor together so that the gutter is camped tighty Fig.22 dimensions in mm uness otherwise stated 45
Downpipe Instaation Jointing Dry jointing ppication range: ppicabe to: Terrain 62mm/75mm square downpipe assembies and 68mm/82mm round downpipe assembies Downpipe 62 mm Downpipe 75 mm 82 Downpipe 68 mm Downpipe mm Fuy support a downpipe and joint fittings with fixing cips positioned at correct intervas Insta fittings with the socket facing upstream NOTE: downpipe fittings except shoes are socket/ spigot Ensure pipe ends are cut square and deburred before connection to fitting Position pipe and fitting cip in mouded groove on fitting heck cip is correcty positioned, by ensuring that the expansion gap is marked Use the sight hoe in the front of the cip to achieve the correct expansion gap Sovent cement jointing ppication range: ppicabe to: Terrain 110mm round downpipe assembies NOTE: The 2100.3 is a dry joint system for externa use. If used internay, it must be sovent weded to make an air-tight system. ternativey, the 100.3 soi system can be used. ut pipe square, deburr and cean mating surfaces with 9101 eaning Fuid oat mating surfaces with 9100 Liquid Wed, using a cean brush ssembe joint immediatey, removing any excess cement with a cean rag Initia set: 3-4 minutes Fina set: 12 hours 110 Downpipe mm Expansion gap Fig.23 2200 ORNIHE system Fig.24 UTION: osey foow directions for use of sovent cement as printed on the container abe. 46 dimensions in mm uness otherwise stated
Jointing Sea ring jointing ppication range: 110 Downpipe mm ppicabe to: Terrain 110mm round downpipe assembies REQUIREMENT: To create a 12mm expansion gap at a pipe joint to aow pipes to expand without distorting the pipework Fie square cut pipe to provide 45 chamfer. (Do not chamfer to a knife edge.) Lubricate rubber sea with 9136 Lubricant Push pipe fuy into socket. Mark pipe as shown (Fig.25) Withdraw pipe unti mark is 12mm from socket to provide required expansion gap nchor the expansion joint with a pipe fixing cip OR (if not practica) anchor a fitting within 1 metre of the joint Fig.25 onversion of sovent wed socket to ring sea joint ppication range: 110 Downpipe 82 mm Downpipe mm ppicabe to: 82mm and 110mm round sovent cemented downpipe assembies, using 109.3/109.4 Sea Ring daptor Under norma use fit 109 daptor to upstream socket ony ean mating surfaces with 9101 eaning Fuid Fit ring sea into 109 oar arefuy appy sovent cement to mating surfaces ssembe immediatey, appying firm even pressure unti coar is correcty positioned Fig.26 dimensions in mm uness otherwise stated 47
acony Outet Instaation acony Outets Instaing screed finish bacony outet ppicabe to: 2172 acony Outet Remove grid Position spacer on ocating pegs Repace screws temporariy to prevent ingress of concrete Lay screed to the eve of the top edge of the spacer Remove screws and repace grid Dress fashing over the rear upstand Tuck fashing into brickwork, joint and point Fig.27 Instaing asphat finish bacony outet ppicabe to: 2174 acony Outet Remove grid Temporariy repace screws to prevent ingress of asphat ppy a suitabe primer or bonding agent up to engraved ine on outet body ppy asphat ayer: dress over outer rim and down to engraved ine on outet body Remove screws Offer up grid and check correct ange of dressing Fit washer and grid, and secure with screws NOTE: The poypropyene washer aows the grid to be easiy removed for maintenance/cearing Fig.28 onnection to downpipes ppicabe to: 2172 and 2174 acony Outets For 68mm round downpipe (2100): use 2173.3.25 Socket daptor For 62mm square downpipe (2200): use 2273.3.23 Socket daptor For 82mm round downpipe (2100.3): connect direct to bacony outet socket Sovent-wed a joints (see page 46) 2273.3.23 2172 or 2174 2173.3.25 2200.23 2100.3 2100.25 Fig.29 48 dimensions in mm uness otherwise stated
Sma Roof Outet Instaation Sma Roof Outets Fixing sma roof outet to proprietary pastic finish ppicabe to: a 2180 and 2181 Roof Outets ppy recommended adhesive to fange of outet body Dress pastic materia over fange to the edge of opening Secure the fat or domed grid with brass screw suppied, ighty camping the roof finish materia in position Fixing sma roof outet to minera fet finish ppicabe to: a 2180 and 2181 Roof Outets ppy suitabe bitumastic primer to fange of outet body ppy iquid bitumen or activator to roof and prepared area of fange Lay first ayer of fet to edge of fange Dress second and third ayers over the fange to the edge of the opening Secure the fat or domed grid with the brass screw suppied, ighty camping the edge of the second and third ayers of fet NOTE: 2180 and 2181 outets are not suitabe for use with hot asphat onnecting spigot/socket bends (sma roof outets) ppicabe to: a sma diameter roof outet Fig.31 2181.2 Domed Outet (sma diameter) Fittings Outet size (mm) Dimension (mm) min max 2180.2 + 207.2.92 55 73 118 2181.2 + 207.2.92 55 73 118 2180.3 + 107.3.92 82 89 168 2181.3 + 107.3.92 82 89 168 2180 2181 ond fet to UPV fange Screw to roof deck Sovent wed pipe Fig.30 dimensions in mm uness otherwise stated 49
Large Roof Outet Instaation Grid Options Fixing to minera fet finish ppicabe to: a 2170 and 2171 Roof Outets 2170.4 2171.4 2171.4 2171.44 ppy suitabe bitumastic primer or bonding agent to bow and fange of outet body ppy iquid bitumen or activator to roof and prepared areas of outet body Lay first ayer of fet to edge of fange Lay second and third ayers over roof outet Dress down into bow to the upstand Secure grid and washer in position with screws suppied Fig.32 NOTE: 2170 fat roof outet is not suitabe for vehicuar traffic Fixing to asphat finish ppicabe to: a 2170 and 2171 Roof Outets ppy suitabe bitumastic primer or bonding agent to bow and fange of outet body Dress a 19mm ayer of asphat over fange and bow to eve of upstand Offer up seected grid (see Fig.32 for aternative grids) check correct ange of dressing and engagement of screws Fig.34 2171.4 Domed Outet Secure grid and washer in position with screws suppied NOTE: The poypropyene washer aows the grid to be easiy removed for maintenance/cearing Fixing to proprietary pastic finish ppicabe to: a 2170 and 2171 Roof Outets ppy recommended adhesive to bow and fange of outet body Lay pastic materia over roof outet Dress over fange and bow to the eve of the upstand Secure grid and washer with screws suppied (see Fig.32 for aternative grids) NOTE: The poypropyene washer aows the grid to be easiy removed for maintenance/cearing Fig.33 2171.4 Domed Outet Fig.35 2171.4 Domed Outet 50 dimensions in mm uness otherwise stated
Large Roof Outets nchoring on thin or uneven roof structures ppicabe to: a 2170 and 2171 Roof Outets onnecting spigot/socket bends (arge roof outets) ppicabe to: a arge roof outets Fig.37 2171.4 Domed Outet Three-ayer fet on insuation materia over profied meta decking Fittings Outet size (mm) Dimension (mm) min max 2170.3 + 107.3.92 82 140 219 2171.3 + 107.3.92 82 140 219 2170.4 + 107.4.92 110 146 257 2171.4 + 107.4.92 110 146 257 Genera fixing detais ppicabe to: bacony and roof outets Three-ayer fet on thin timber decking Sovent wed pipe-end, or spigot of bend, to roof outet (for jointing techniques, see page 46) Locate outet body in roof structure and check that a suitabe rigid fixing can be made Screw down outet firmy to roof structure Remove grid ppy seected roof finish Heping you sove probems Terrain products are backed by a comprehensive Technica dvisory Service, which is here to provide you with advice and design guidance on a aspects of above and beow ground drainage. Teephone 01622 795200 Fax 01622 716796. Panning and deveopment stage The technica services avaiabe to hep you at this stage incude: Drainage system design, incuding detaied drawings Specification, product scheduing and estimating Design and production of bespoke fittings to meet specific appication requirements NS Specification causes avaiabe The Terrain Fabrication Service heps specifiers and contractors overcome probems both at the design stage, and on site. The Service can provide soutions to even the most demanding probems by fabricating specia components to order. Quaity and assurance Terrain is accredited to S EN ISO 9001:2000 Management Systems. systems are manufactured to the reevant European Standard and where appicabe certified to ritish Standard. EN 607 Eaves Gutters and Fittings made from PV-u EN 1462 rackets for Eaves Gutters EN 12200 Pastic rainwater piping for above ground externa use PV-u dimensions in mm uness otherwise stated 51
Index ODE DESRIPTION PGE NO. 100.4.30 110MM DOWNPIPE - 3.0M 13 100.4.40 110MM DOWNPIPE - 4.0M 13 101.4.92 SWEPT END - 92½ 13 101.4.112 SWEPT END - 112½ 13 101.4.135 SWEPT END - 135 13 103.4.92 ESS END (DOULE SOKET) 13 104.4.92 RNH (LL SOKET) - 92½ 13 104.4.135 RNH (LL SOKET) - 135 13 105.4.92 ESS RNH 13 107.4.135 SPIGOT END 13 107.4.92 SPIGOT END (LONG TIL) 14 110.4 STRIGHT OUPLER 14 111.4 EXPNSION OUPLER 14 138.4 ESS PIPE 15 139.4 ESS PIPE 15 143.3 ONE-PIEE DOWNPIPE RKET 12 143.4 ONE-PIEE DOWNPIPE RKET 15 2100.25.30 68MM DOWNPIPE 3.0M 8 2100.25.40 68MM DOWNPIPE 4.0M 8 2100.25.55 68MM DOWNPIPE 5.0M 8 2100.3.40 82MM DOWNPIPE - 4.0M 11 2101.25.112 LONG RDIUS END 8 2101.3.92 SWEPT END - 92½ 11 2101.3.112 SWEPT END - 112½ 11 2101.3.135 SWEPT END - 135 11 2107.25 STRIGHT OUPLER 8 2107.3 STRIGHT OUPLER (DOULE SOKET) 11 2108.25.92 SHORT END - 92½ 8 2108.25.112 SHORT END - 112½ 8 2109.25.92 RNH - 90 8 2109.25.112 RNH - 112½ 8 2109.3.92 RNH (LL SOKET) - 92½ 11 2109.3.112 RNH (LL SOKET) - 112½ 11 2110.3 SHOE 11 2110.4 SHOE 14 2111.25 RINWTER HED 9 2111.3 RINWTER HED 12 2112.25.T PIPE ND FITTING RKET (DJUSTLE) 9 2112.25.D PIPE ND FITTING RKET (DRIVE-IN) 9 2113.25 PIPE FITTING LIP 9 2113.25 ENTRL FIXING LIP 9 2116.25 PIPE FITTING RKET 10 2137.25 ESS PIPE 10 2137.3 ESS PIPE 12 2150.4.40 RESENT GUTTER - 4.0M 20 2151.4 JOINT RKET 20 2152.4 SUPPORTING RKET 20 2153.4.25 RUNNING OUTLET 20 2154.4.90 GUTTER NGLE - 90 20 ODE DESRIPTION PGE NO. 2154.4.120 GUTTER NGLE - 120 20 2154.4.135 GUTTER NGLE - 135 20 2154.4.156 GUTTER NGLE - 156 20 2155.4 SHORT STOP-END 21 2156.4 INTERNL STOP-END 21 2157.4.25 STOP END OUTLET 21 2158.4.45 RESENT TO 4½ ST IRON SPIGOT 21 2159.4.45 RESENT TO 4½ ST IRON SOKET 21 2160 SIDE RFTER RKET (DJUSTLE) 31 2161 TOP RFTER RKET (DJUSTLE) 31 2162 RISE ND FLL RKET (DJUSTLE) DRIVE IN RKET 2166 SPER LOK (STRIGHT) 32 2166.22 SPER LOK (TPERED) 32 2167 DPTOR TO OTHER PV-U GUTTERS 21 2167 DPTOR TO OTHER PV-U GUTTERS 32 2168.4.45 RESENT TO 4½ OGEE ST IRON SPIGOT 22 2169.4.45 RESENT TO 4½ OGEE ST IRON SOKET 22 2170.3 FLT ROOF OUTLET (LRGE) 5 2170.4 FLT ROOF OUTLET (LRGE) 5 2171.3 DOMED ROOF OUTLET (LRGE 5 2171.4 DOMED ROOF OUTLET (LRGE 5 2172.3 LONY OUTLET 6 2173.3.25 SOKET DPTOR (82MM X 68MM) 6 2174.4 INVERTED ROOF OUTLET 5 2174.44 INVERTED ROOF OUTLET 5 2174.3 LONY OUTLET 6 2180.2 FLT ROOF OUTLET (SMLL DIMETER) 5 2180.3 FLT ROOF OUTLET (SMLL DIMETER) 5 2181.2 DOMED ROOF OUTLET (SMLL DIMETER) 5 2181.3 DOMED ROOF OUTLET (SMLL DIMETER) 5 2200.23.30 DOWNPIPE - 3.0M 16 2200.23.40 DOWNPIPE - 4.0M 16 2200.23.55 DOWNPIPE - 5.0M 16 2207.23 STRIGHT ONNETOR 16 2208.23.92 END - 92½ 16 2208.23.112 END - 112½ 16 2209.23.112 RNH 16 2210.23 SHOE 16 2211.23 RINWTER HED 17 2212.23 PIPE ND FITTING RKET (DJUSTLE) 17 2213.23 PIPE ND FITTING RKET (DJUSTLE) 17 2214.23 WLL OFFSET 17 2215.23.25 DPTOR (SQURE TO ROUND) 17 2216.23 LONG STND-OFF DOWNPIPE RKET 17 2237.23 ESS PIPE 16 2250.5.40 ORNIHE GUTTER - 4M 23 2251.5 JOINT RKET 23 2252.5 SUPPORT RKET 23 31 52
ODE DESRIPTION PGE NO. 2253.5.23 RUNNING OUTLET 23 2254.5.90 GUTTER NGLE - 90 24 2254.5.120 GUTTER NGLE - 120 24 2254.5.135 GUTTER NGLE - 135 24 2255.5 SHORT STOP-END 24 2257.5.23 STOP-END OUTLET 24 2265 SUPPORT STRP (LL SYSTEMS) 31 2273.3.25 SOKET DPTOR (82MM X 62MM) 6 2300.33.40 DOWNPIPE - 4.0M 18 2307.33 STRIGHT ONNETOR 18 2308.33.112 END 18 2309.33.112 RNH 18 2310.33 SHOE 19 2311.33 RINWTER HED 19 2313.33 PIPE ND FITTING RKET 19 2314.23 WLL OFFSET 19 2315.33.23 DPTOR (SQURE TO SQURE) 19 2337.33 ESS PIPE 19 2350.6.40 STREMLINE GUTTER - 4.0M 25 2351.6.12 JOINT RKET 25 2352.6 SUPPORT RKET 25 2352.15 OVERSLUNG RKET 25 2353.6.33 RUNNING OUTLET - TO 75MM SQURE DOWNPIPE 25 2353.6.3 RUNNING OUTLET - TO 82MM ROUND DOWNPIPE 25 2353.6.4 RUNNING OUTLET - TO 110MM ROUND DOWNPIPE 25 2354.6.90 GUTTER NGLE - 90 26 2354.6.135 GUTTER NGLE - 135 26 2355.6 SHORT STOP-END 26 2357.6.33WLH STREMLINE STOP END OUTLET LEFT HND 26 2357.6.33WRH STREMLINE STOP END OUTLET RIGHT HND 26 2360 SIDE RFTER RKET (DJUSTLE) 31 2361 TOP RFTER RKET (DJUSTLE) 31 2362 RISE ND FLL RKET (DJUSTLE) DRIVE IN RKET 2368.3 SREWED OUTLET DPTOR 26 2450.5.40 RPIDFLOW GUTTER - 4.0M 27 2451.5 JOINT RKET 27 2452.5 SUPPORT RKET 27 2453.5.25 RUNNING OUTLET - TO 68MM ROUND DOWNPIPE 27 2453.5.3 RUNNING OUTLET - TO 82MM ROUND DOWNPIPE 27 2454.5.90 GUTTER NGLE - 90 27 2454.5.135 GUTTER NGLE - 135 27 2455.5 SHORT STOP-END - 28 2457.5.25 STOP-END OUTLET - 82MM ROUND DOWNPIPE 28 2457.5.3 STOP-END OUTLET - 82MM ROUND DOWNPIPE 28 2467 DPTOR LIP TO OTHER PV-U GUTTERS 28 2467 DPTOR LIP TO OTHER PV-U GUTTERS 33 2550.5.40 OMEG GUTTER - 4.0M 29 2551.5 JOINT RKET 29 31 ODE DESRIPTION PGE NO. 2552.5 UNDERSLUNG SUPPORT RKET 29 2552.5 UNDERSLUNG SUPPORT RKET 29 2552.5.150 OVERSLUNG SUPPORT RKET 29 2553.5.25 RUNNING OUTLET 29 2554.5.90I INTERNL GUTTER NGLE - 90 30 2554.5.135I INTERNL GUTTER NGLE - 135 30 2554.5.90E EXTERNL GUTTER NGLE - 90 30 2554.5.135E EXTERNL GUTTER NGLE - 135 30 2555.5L SHORT STOP-END (EXTERNL) - LEFT 30 2555.5R SHORT STOP-END (EXTERNL) - RIGHT 30 2556.5L INTERNL STOP-END - LEFT 30 2556.5R INTERNL STOP-END - RIGHT 30 2557.5.25L STOP-END OUTLET - LEFT 30 2557.5.25R STOP-END OUTLET - RIGHT 30 9100.125 LIQUID WELD - 125ML 34 9100.250 LIQUID WELD - 250ML 34 9100.500 LIQUID WELD - 500ML 34 9101.125 SOLVENT LENING FLUID - 125ML 34 9101.250 SOLVENT LENING FLUID - 250ML 34 9136.250 TERRIN SILIONE LURINT 34 9136.500 TERRIN SOLULE LURINT 34 9911 GUTTER SEL - FOR 2100 RESENT 32 9915.25 GUTTER OUTLET GURD 32 9922 GUTTER SEL - FOR 2200 ORNIHE 32 9933 GUTTER SEL - FOR 2300 STREMLINE ND 2500 OMEG 9944 GUTTER SEL - FOR 2400 RPIDFLOW 32 9980 SPRE GRID FOR DOMED ROOF OUTLET -FOR 2171 7 9981 SPRE GRID FOR FLT ROOF OUTLET -FOR 2170 7 9990 SPRE GRID FOR LONY OUTLET -FOR 2172 7 9995.3 P FOR LONY OUTLET 7 3DW25 DPTOR TO UNDERGROUND DRIN 33 4D76 UNIVERSL RINWTER DPTOR 34 4DW23 DPTOR TO UNDERGROUND DRIN 33 4DW25 DPTOR TO UNDERGROUND DRIN 33 4DW3 DPTOR TO UNDERGROUND DRIN 33 4DW33 PIPE DPTOR 4 X 3 / 75MM SQ 33 S2308.33.92 3X3 SQ S/LINE END 18 S2309.33.92 3X3 SQ S/LINE RNH 18 32 53
54 Notes
Information in this pubication must not be reproduced in whoe or in part without the permission of Poypipe. The contents are given in good faith and no warranty is given or impied in respect of such information. Poypipe reserve the right to amend this specification without prior notice and a transactions are subject to our standard onditions of Sae. and are registered Trademarks of Poypipe. Poypipe products are protected by Design Right under DP 1988. opyright 2006 Poypipe. rights reserved. 55
Terrain Rainwater Poypipe Guf FE Poypipe Terrain Dubai Media ity Loft Office No. 3 Entrance, 4th Foor Office No. 404 P.O. ox 502320 Dubai United rab Emirates Te: +971 (0) 4 454 8328 New Hythe usiness Park oege Road yesford Kent ME20 7PJ United Kingdom Te: +44 (0)1622 795200 Fax: +44 (0)1622 716796 Fax: +971 (0) 4 454 2949 commerciaenquiries@poypipe.com internationa@poypipe.com www.terraindrainage.com www.poypipeguf.com www.poypipe.com