K-66 ERIE HOT ATER ANITIZING INGLE-TANK RACK CONVEYOR IHAHER pecial Features: ynchronized side-drive dual rack rail pawl-bar system ensures complete water coverage from every angle, even the bottom of the rack Large, insulated front are spring-loaded to open easily and TAY open, without latching Computer-positioned wash arms in easily-removed manifolds. Arms and manifolds are stainless steel, eliminating high-wear gaskets and O-rings Concave, slotted nozzles minimize clogging. Nozzles are computer-positioned at varying angles to maximize water coverage over all areas of the ware Powerful 3hp wash pump is 50% more powerful than the industry standard for outstanding cleaning Large separation between wash and rinse (6 / 406mm upper, 7 /43mm lower) avoids splashing of soiled water onto sanitized ware Front-sloping tanks for complete drainage and easier cleaning External, easily-operated lever drain system makes draining fast, safe and simple tandard Features: ENERGY TAR Qualified Capacity 39 racks per hour ater consumption 0.43 gallons (.63 liters) per rack All 304-series stainless steel construction ouble-wall insulated construction on front, top and back to improve operator safety, conserve heating energy, and reduce noise and heat loss into the dishroom Large, easily-removed pan strainers with separate prewash scrap basket Fully automatic operation including auto-fill and autostart. Prewash, wash and final rinse are activated only when a rack is in place to conserve water and detergent Powerful 3hp (. k) wash pump. Pumps are verticallymounted to be self-draining and easily removed for servicing Electromechanical controls for reliability and easy operation. Low-voltage 4VAC control circuit for operator safety Easily accessible detergent and rinse aid injection ports for fast and easy chemical dispenser installation ingle-point electrical, water and drain s. Internal booster heater option adds an additional terminal block for simpler replacement of an existing external booster heater Low-level heater protection Pressure reduction valve ( with internal booster heater) Options: Choice of two heights (standard 8 /457mm or tall hood 6 /660mm) Internal booster heater (steam or electric heat) External booster heater (steam or electric heat) External vent fan control limit switch (end stop or whisker switch versions) Vent cowl collars irect drive sideloader 90 powered loader or unloader Flanged feet rain water tempering kit hock arrestor Pressure reduction valve ( without internal booster heater) Models: K-66E: 8 vertical, electric heat K-66: 8 vertical, steam coil heat K-66ET: 6 vertical, electric heat K-66T: 6 vertical, steam coil heat K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us
K-66 eries, left-to-right - electric heat w/o internal booster OR steam heat (all) (0mm) Control Vent cowl collar(s) (optional) 7" (78mm) lip-in height ' 0" (864mm) 9-5/8" (44mm) 6-/" (65mm) 4-3/ (mm) rain 8-/8 (05mm) 9-/ (4mm) ' 3-/ 3-/" (90mm) recommended 6 / (84mm) 5" (7mm) 7-/8" (485mm) 5-/" (40mm) " (80mm) " (5mm) 3-/8" (80mm) 7-/" (89mm) ' -3/, (374mm) irection of travel ' (405mm) ' 8-/" (5mm) ' 3-/" ' 6-/ (768mm) 8" (03mm) ' 0" (559mm) 3' 8" (8mm) -to-table 5' 6" (676mm) Vent cowl collar centerline 6 3-/ (98mm) 6' 0" (083mm) Horizontal ' 8-/" (50mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. tandard height Tall hood ' 6" (457mm) ' (660mm) open 3 Vertical 4 4' 9-7/8" (47mm) 5' 5-7/8" (673mm) 3 6' 7-7/8" (030mm) 7' -7/8" (435mm) 4 5' 9-/8" (756mm) 6' 5-/8" (435mm) 5 5' (66mm) 6' (89mm) ash section rain 5 Utility Connection ymbols Utility ratings and specifications on Page 6. K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us rain Ventilation ater team Condensate return
K-66 eries, right-to-left - electric heat w/o internal booster OR steam heat (all) Vent cowl collar(s) (optional) Control (0mm) 7" (78mm) ' 3-/ 9-/ (4mm) 4-3/ (mm) rain 8-/8 (05mm) 6-/" (65mm) 9-5/8" (44mm) lip-in height ' 0" (864mm) 3-/8" (80mm) " (80mm) " (5mm) 3-3/8" (948mm) 5-/" (40mm) 6 / (84mm) 5" (7mm) 3-/" (90mm) recommended ' 6-/ (768mm) ' -3/ (374mm) ' 3-/" ' (405mm) ' 8-/" (5mm), irection of travel 7-/" (89mm) 8" (03mm) Horizontal ' 8-/" (50mm) 3' 8" (8mm) ' 0" (559mm) -to-table 5' 6" (676mm) Vent cowl collar centerline 6 3-/ (98mm) 6' 0" (083mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. tandard height Tall hood ' 6" (457mm) ' (660mm) open 3 Vertical 4 4' 9-7/8" (47mm) 5' 5-7/8" (673mm) 3 6' 7-7/8" (030mm) 7' -7/8" (435mm) 4 5' 9-/8" (756mm) 6' 5-/8" (435mm) 5 5' (66mm) 6' (89mm) ash section rain 5 Utility Connection ymbols Utility ratings and specifications on Page 6. K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us rain Ventilation ater team Condensate return
K-66 eries, left-to-right - electric heat with internal booster (0mm) Control Vent cowl collar(s) (optional) 7" (78mm) lip-in height ' 0" (864mm) 4-3/ (mm) rain 9-5/8" (44mm) 6-/" (65mm) 3-/" (90mm) recommended 6 / (84mm) (0mm) 5" (7mm) 3-/8" (384mm) (0mm) (0mm) 7-/" (89mm) irection of travel ' (405mm) ' 8-/" (5mm) ' -3/ (374mm) ' 3-/" ' 6-/ (768mm) 8" (03mm) ' 0" (559mm) 3' 8" (8mm) -to-table 5' 6" (676mm) Vent cowl collar centerline 6 3-/ (98mm) 6' 0" (083mm) Horizontal ' 8-/" (50mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. tandard height ' 6" (457mm) Tall hood ' (660mm) open 3 Vertical 4 5' 9-/8" (756mm) 6' 5-/8" (435mm) 3 6' 7-7/8" (030mm) 7' -7/8" (435mm) 4 5' (66mm) 6' (89mm) 5 5' " (576mm) 5' 0" (778mm) ater 5 Utility Connection ymbols Utility ratings and specifications on Page 6. rain ater rain Ventilation K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us
K-66 eries, right-to-left - electric heat with internal booster Vent cowl collar(s) (optional) Control (0mm) 7" (78mm) 4-3/ (mm) rain lip-in height ' 0" (864mm) 6-/" (65mm) 9-5/8" (44mm) (0mm) (0mm) 3-/8" (384mm) ' 0-/ (564mm) 5" (7mm) 6 / (84mm) 3-/" (90mm) recommended ' 6-/ (768mm) ' -3/ (374mm) ' 3-/" ' (405mm) ' 8-/" (5mm) irection of travel 7-/" (89mm) 3' 8" (8mm) ' 0" (559mm) -to-table 5' 6" (676mm) Vent cowl collar centerline 6 3-/ (98mm) 6' 0" (083mm) 8" (03mm) Horizontal ' 8-/" (50mm) Variable imensions All dimensions from floor are +/- /" due to adjustable feet. tandard height ' 6" (457mm) Tall hood ' (660mm) open 3 Vertical 4 5' 9-/8" (756mm) 6' 5-/8" (435mm) 3 6' 7-7/8" (030mm) 7' -7/8" (435mm) 4 5' (66mm) 6' (89mm) 5 5' " (576mm) 5' 0" (778mm) ater 5 Utility Connection ymbols Utility ratings and specifications on Page 6. rain ater rain Ventilation K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us
K-66 eries Utility Connections rain -5/6 (75mm) O vertical, gravity-fed drain outlet (HPE piping). Recommend placement directly above 4 floor drain. Additional piping to drain (if so required) to be supplied by customer. Connection is 9-5/8" (44mm) AFF. If using optional NPT adapter, is 8-/ (4mm) AFF. Refer to etail View: rain for suggested. ingle electrical ingle terminal block inside control box (4-wire with ground - no neutral). ual electrical s - with internal electric booster heater Two terminal blocks inside control box (4-wire with ground - no neutral). - Machine electrical supply - Booster heater electrical supply supply (or supplies) should be routed into control box through strain relief(s) on rear of control box. Incoming leads must be appropriately sized for electrical supply. Individual disconnect with lockout/tagout strongly recommended (provided by customer). Connection for standard-height is 5 4 (66mm) AFF. Connection for tall hood is 6 (89mm) AFF. Refer to utility chart on Page 7 for electrical load information. Vent - with optional vent cowl collars Refer to etail View: Vent for suggested. The waste air must be corrosion-resistant and frost-free. In particular, provisions must be made to prevent air temperatures of 3 F/0 C or colder from reaching the machine at any time. A provision for draining moisture from the waste air pipe is strongly recommended. Load end - 00 CFM Unload end - 350 CFM Total - 550 CFM Hot water - without internal booster heater /" NPT female pipe is 9-/" (4mm) AFF. Temperature 80 F (8 C) Pressure 5-5 PI (.0-.7 bars) Initial fill 4.3 U.. gals. (60. liters) Consumption 0.0 U.. gals per hour (386. liters) per hour Recommended hardness -6 grains/u.. gal. ater - with internal booster heater only For steam heat, /" NPT female pipe is 9-/" (4mm) AFF. For electric heat, /" NPT female pipe is 5' " (576mm) AFF for standard- 5' 0" (778mm) AFF with tall hood option. Temperature: Machines with 40 F booster: 40 F (60 C) Machines with 70 F booster: 0 F (43 C) Pressure 5-5 PI (.0-.7 bars) Initial fill 4.3 U.. gals. (60. liters) Consumption 0.0 U.. gals per hour (386. liters) per hour Recommended hardness -6 grains/u.. gal. team - steam-heated Pipe is ' 3-/ AFF. Machines without internal steam booster heater: 3/ male NPT Machines with internal steam booster heater: -/ male NPT 0-30 PI CONTANT steam pressure is REQUIRE. If pressure is above 30 PI, use of a regulator is REQUIRE (supplied by customer). The pipe does NOT reflect the steam line size from the boiler to the dishwasher. The necessary steam line sizing must be determined by the facility's steam engineer based on the pressure and volume requirements. Consumption: Refer to utility chart on Page 7 Condensate return - steam-heated 3/ NPT male pipe is 8-/8" (05mm) AFF. Condensate line MUT be pressure-free. Vent Connection Machines equipped with optional vent cowl collars may be installed underneath a ventilation hood, or may use pant leg ventilation ducts (to be supplied by the customer). To determine the dimensions of the duct, first determine how they will be installed: uct sleeved outside collar Inside dimensions of duct: 4 x 6 (0 x 406mm). uct sleeved inside collar Outside dimensions of duct: 3-3/4 x 5-3/4 (95 x 400mm). The duct must not interfere with the adjustable baffle, as shown. Adjustable baffle uct sleeved outside collar (recommended) 4 x 6 (0x406mm) inside dimensions " (50mm) max. uct sleeved inside collar (if required) 3-3/4 x 5-3/4 (95x400mm) outside dimensions / (3mm) max. rain Connection The machine is equipped with a -5/6" (75mm) O vertical, gravity-fed drain. If possible, the machine drain can simply be positioned directly above a floor drain. If a floor drain is not in the correct location, or if local codes require a trap, a " indirect drain line may be attached using the supplied " NPT male adapter. Choose a piping material that: Complies with any applicable local and national codes Is rated for use with water temperatures up to 80 F/8 C Is rated for 3- ph to accommodate detergents and rinse aid in the drain water 9-5/8 (44mm) 8-/ (4mm) Optional NPT adapter Recommended Tabling Construction Check that the table lip overlaps BOTH the inner and outer s. Use silicone sealer between the table lip and the machine to prevent leakage. top 3 (864mm) AFF Outside view Outer (with support lip) Inner 0-/ (55mm) recommended 0-/" (5mm) max. Outer (with support lip) Inside view turndown flange 3/ (9mm) max. Inner K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us
K-66 eries Technical pecifications Operating Capacities (NF Rated) Racks per hour... 39 ishes per hour... 5,975 Glasses per hour... 8,604 Conveyor pecifications Conveyor belt speed... 6.64 feet/min. (.0m/min.) Horizontal... 8-/ (50mm) Vertical (K-66E, K-66)... 6 (457mm) Vertical (K-66ET, K-66T)... (660mm) ater pecifications Minimum water temperatures: Prewash tank... No minimum - 0-40 F (43-60 C) typical ash tank... 60 F (7 C) Final rinse... 80 F (8 C) Minimum incoming water temperature: Machines without internal booster... 80 F (8 C) Machines with internal booster... 0 or 40 F (43 or 60 C) Initial fill... 4.3 U.. gals. (60. liters) Prewash tank capacity... 7. U.. gals. (65. liters) ash tank capacity... 5. U.. gals. (95.0 liters) Venting pecifications Load end... 00 CFM (336m 3 /h) Unload end... 350 CFM (588m 3 /h) Total... 550 CFM (94m 3 /h) hipping Information K-66E, K-66: Machine weight... 7 lbs. (3kg) hipping weight... 789 lbs. (359kg) Crating (LxxH)... 7 5 x 3 x 6 3 (.3 x 0.9 x.9m) 39. cu. ft. (3.8m 3 ) K-66ET, K-66T: Machine weight... 79 lbs. (359kg) hipping weight... 869 lbs. (395kg) Crating (LxxH)... 7 5 x 3 x 6 (.3 x 0.9 x.m) 53.9 cu. ft. (4.3m 3 ) Incoming water line size... / NPT Recommended water hardness... -6 grains/u.. gal. Consumption at 00% capacity:... 0.0 U.. gals. (386. liters)/hr. 0.43 U.. gals. (.6 liters)/rack Final rinse flow pressure... 5-5 PI (.0-.7 bars) Flow rate....70 U.. gals.(6.44 liters)/min. pecifications Machine supply Peak Minimum Maximum current supply circuit breaker/ draw ampacity disconnect K-66E (standard electric tank heat) 08V/60 Hz/3 Ph 54.4 A 70 A 70 A 30V/60 Hz/3 Ph 49.3 A 70 A 70 A 460V/60 Hz/3 Ph 4.6 A 35 A 35 A K-66ET (tall hood, electric tank heat) 08V/60 Hz/3 Ph 66.7 A 90 A 90 A 30V/60 Hz/3 Ph 58.0 A 80 A 80 A 460V/60 Hz/3 Ph 8.4 A 40 A 40 A K-66, K-66T (standard height and tall hood, steam coil tank heat) 08V/60 Hz/3 Ph.7 A 0 A 0 A 30V/60 Hz/3 Ph.8 A 0 A 0 A 460V/60 Hz/3 Ph 5.8 A 5 A 5 A Internal booster heater Rating, Rating, Peak Minimum Maximum supply machine machine current supply circuit breaker/ startup operation draw ampacity disconnect 40 F rise electric booster (40 F/60 C water supply temperature) 08V/60 Hz/3 Ph 8.0 k 0.8 k 50.0 A 70 A 70 A 30V/60 Hz/3 Ph 8.0 k 0.8 k 45.0 A 60 A 60 A 460V/60 Hz/3 Ph 8.0 k 0.8 k.6 A 30 A 30 A 70 F rise electric booster (0 F/43 C water supply temperature) 08V/60 Hz/3 Ph 8.8 k.6 k 79.9 A 00 A 00 A 30V/60 Hz/3 Ph 8.8 k.6 k 7.3 A 00 A 00 A 460V/60 Hz/3 Ph 8.8 k.6 k 36. A 50 A 50 A Electric tank heater ratings (K-66E, K-66ET) 08V/60Hz/3Ph 30V/60Hz/3Ph 460V/60Hz/3Ph K-66E 5.0 k 4.6 k 5.0 k K-66ET 9.5 k 8.0 k 8.0 k Prewash pump motor... 0.75 hp (0.55 k) ash pump motor... 3.0 hp (. k) Conveyor motor... 0.5 hp (0.09 k) team pecifications (K-66, K-66T) team line : Machines without internal steam booster heater... 3/4 NPT Machines with internal steam booster heater... -/4 NPT Condensate return... 3/4 NPT team pressure... 0-30 psi (0.7-.0 bars) team consumption: Tank heat... 60 lbs./hr. 40 F rise steam booster (40 F/60 C water supply temperature)... +50 lbs./hr. 70 F rise steam booster (0 F/43 C water supply temperature)... +00 lbs./hr. External Booster Heater Recommendations (for without optional internal booster heater) Booster ratings are based on peak capacity of 0.0 U.. gals. (386. liters) per hour and a flow rate of.70 U.. gals. (6.44 liters) per minute. Recommended boosters are one size larger than required to help compensate for any local conditions that may prevent full performance. ater supply Required Recommended temperature temperature rise booster rating 0 F/43 C... 70 F/39 C... 4 k 40 F/60 C... 40 F/ C... k Note: All specifications are subject to change without notice based on MEIKO s dedicated product improvement program. K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us
Equipment pecification: K-66 Rack Conveyor ishwasher- Item No. Item will be an NF and ETL-listed MEIKO K-66 single tank, rack conveyor dishwasher, consisting of a prewash zone with 3/4 hp (0.55 k) pump motor, a wash zone with 3 hp (. k) pump motor, and a final rinse zone. Total length of the tank section (not including vent cowls) will be 5 6 (676mm). Unit will utilize a 80ºF/8 C minimum fresh water sanitizing rinse. Unit will have a capacity of 39 racks per hour at an NF-rated belt speed of 6.64 feet (.0m) per minute. Unit will consume an NF-rated 0.0 U.. gals./386. liters per hour (0.43 U.. gals./.6 liters per rack). characteristics: 08V/60 Hz/3 Ph 30V/60 Hz/3 Ph 460V/60 Hz/3 Ph ash tank temperature will be maintained at a minimum of 60 F/7 C. Tank heating will be accomplished by: Thermostatically-controlled electric heating elements (K-66E, K-66ET) Thermostatically-controlled stainless steel steam coils (K-66, K-66T) irection of conveyor travel will be: Right-to-Left Left-to-Right Unit will have the following standard features: ouble-wall, insulated construction on top, front, and rear. Two upper prewash arms and one lower prewash arm. Five upper wash arms with 9 (483mm) wash area and four lower wash arms with 4 (356mm) wash area. ash arm spray pattern ensures effective coverage with varying angles and offset spray jets. lotted, concave wash nozzles and captivated end caps for easier cleaning. Minimum separation between wash and final rinse of 6 (406mm) upper and 7 (43mm) lower. ynchronized rack rail pawl bar system for smooth rack movement. ide drive system provides easy cleaning access and eliminates wash pattern obstruction. Front-sloping tanks for complete tank drainage, accessibility, and cleanability. Fully automatic operation including auto-fill and auto-start. eparate compartment actuator switches to ensure prewash, wash and final rinse are energized only when a rack is in place. External, easily operable, lever-operated drain system. Low level heater protection. Prewash and wash pump motors are self-draining, internal and vertically installed for easy access and serviceability. ash pump housing and impeller constructed of stainless steel. Electromechanical controls with a 4 VAC control circuit. ingle point electrical. Easily removable wash arm block manifold systems, prewash arms and final rinse arms. Large front access can be opened with one hand and remain open without latches, aiding machine accessibility and cleanability. Large, removable stainless pan strainers with separate prewash scrap basket. ingle point drain. Pressure reduction valve ( with internal booster heater only). Unit will have the following optional features (check all that apply): Tall hood option to increase vertical from 6 (457mm) to (660mm) Internal booster heater (steam or electric per machine spec). ly-heated internal booster heater adds electrical terminal block to machine ( total). ized for a minimum 40 F ( C) rise and 40 F (60 C) min. incoming water temperature ized for a minimum 70 F (39 C) rise and 0 F (43 C) min. incoming water temperature External booster heater ized for a minimum 40 F ( C) rise and 40 F (60 C) min. incoming water temperature ized for a minimum 70 F (39 C) rise and 0 F (43 C) min. incoming water temperature team heated ly heated External vent fan control limit switch Inline (whisker switch) style End stop style Vent cowl collar(s) with adjustable damper 4 x 6 x 7 H (0x406x78mm) At both ends At load end only At unload end only 90 side loader (unhooded), 3 long 90 side loader (hooded), 3 long 90 power loader, 34-/4 long 90 power unloader, 34-/4 long Flanged, bolt-down feet rain water tempering kit hock arrestor Pressure reduction valve ( without internal booster heater only) K-66 eries Updated 9- MEIKO 349 Heil Quaker Blvd. LaVergne, TN 37086 (800) 55-MEIKO FAX (65) 399-660 www.meiko.us