Wall Mounted BBQ Rangehood GRHM & GRHL GRHM GRHL Gasmate is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au Aber Hamilton, N.Z. www.gasmate.co.nz Important: Retain these instructions for future use. 02896 05/13 M
USE, CARE AND INSTALLATION GUIDE Read all instructions before installing and operating this appliance IMPORTANT SAFETY NOTICE WARNING Installation The installation in this manual is intended for qualified installers, service technicians or persons with similar qualified backgrounds. DO NOT attempt to install this appliance yourself. Injury could result from installing the unit due to lack of appropriate electrical and technical background. Always ensure this range hood is installed as per the requirements noted in AS/NZS 3000:2007 There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back in to the room; CAUTION: Accessible parts may become hot when used with cooking appliances. There is a risk if cleaning is not carried out in accordance with the instructions Do not flambé under the range hood The air must not be discharged into an existing flue that is used for exhausting fumes from appliances burning gas or other fuels This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. All electrical wiring must be properly installed, insulated and grounded. It is not recommended to use old duct work it should be replaced if necessary to avoid the possibility of a grease fire. Check all joints on duct work to ensure proper connection all joints should be properly taped. Do not attempt to modify this appliance as this could cause injury and will void your warranty Underside surfaces can become hot during use. Do Not Touch. Operations Read all instructions in this manual before operating the appliance. Save these instructions for future reference. Always leave safety grills and filters in place. Without these components, operating blowers could catch on to hair, fingers and loose clothing. NEVER dispose cigarette ashes, ignitable substances or any foreign objects in to the blowers. NEVER leave cooking area unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of selfcombustion is higher when the oil has been used several times. Cleaning The saturation of greasy residue in the blowers and filters may cause increased flammability. Keep unit clean and free of grease and residue build-up at all times to prevent possible fires. Filters must be cleaned periodically and be free from accumulation of cooking residue (see cleaning instruction). Old and worn filters must be replaced immediately. Do not operate blowers when filters are removed. Never disassemble parts to clean without proper instructions. Disassembly is recommended to be performed by qualified personnel only. Call our service centre for removal instructions. SITRO GROUP AUSTRALIA Declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. SITRO GROUP AUSTRALIA further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance. 2
Electrical Data IMPORTANT the mains power supply for Australia / New Zealand and meets the requirements of Australian Standards. This range hood must be connected to a supply voltage that is equal to that stated on the rating label. If the mains power connection plug or power cord becomes damaged it must be replaced with a complete assembly that is identical to the original, and this must be replaced by an authorised service centre. Always follow the Australian / New Zealand requirements for connection INSTALLATION MOUNTING HEIGHTS AND CLEARANCE The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. When the range hood is located above a gas appliance, this distance shall be at least 120cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account. Minimum mount height above cooking surface should be no lower than 1200mm (120cm) It is important to install the hood at the proper mounting height. Hoods mounted too low could hoods mounted too high will be hard to reach and min 1200mm max 2700mm Extension available Maximum ceiling clearance 2700mm at 1200 mm hood mounting height (depending on model used) Minimum duct size: GRHM - Round 2x150mm diameter GRHL - Round 3 x 150mm diameter 915mm Flexible ducts are supplied for convenience, always use rigid type metal ducts if available to Flexible Duct Material (Supplied), Notes for Installation. 1) Never combine the ducts, always flue all ducts individually to the atmosphere and ensure a cap and flashing are used on all ducts. GRHM 2 motors and 2 ducts GRHL 3 motors and 3 ducts 2) When using screws and silver tape to join the flexible duct to the rangehood, ensure that the screws and silver tape do not interfere with the operation of the butterfly baffles. NOTE: Check butterfly baffles operation before completing the duct installation. 3) Ensure that the flexible ducts are as straight as possible with no excess curves, as the excess curves will reduce the airflow by at least 50%. 4) Always ensure that the rangehood is level in all directions and an un-level rangehood will reduce air flow by at least 30%. Note: Incorrect installation is not covered under warranty. 3
DUCTING WARNING: FIRE NEVER Exhaust air or terminate duct work into spaces between walls, crawl spaces, ceilings, attics or garages. All exhaust must be ducted to the atmosphere. Use Metal duct work only. Fasten all connections with sheet metal screws Side wall cap with gravity damper duct tape. Flexible Duct Material (Supplied), Notes for Installation. 1) Never combine the ducts, always flue all ducts individually to the atmosphere and ensure a cap and flashing are used on all ducts. GRHM 2 motors and 2 ducts GRHL 3 motors and 3 ducts 2) When using screws and silver tape to join the flexible duct to the rangehood, ensure that the screws and silver tape do not interfere with the operation of the butterfly baffles. NOTE: Check butterfly baffles operation before completing the duct installation. Roof Pitch with Flashing & Cap 3) Ensure that the flexible ducts are as straight as possible with no excess curves, as the excess curves will reduce the airflow by at least 50%. 4) Always ensure that the rangehood is level in all directions and an un-level rangehood will reduce air flow by at least 30%. Note: Incorrect installation is not covered under warranty. Side wall cap with gravity damper Ceiling or crawl space 4
INSTALLATION Mounting the Range Hood 1. Measure from cooking surface to hood bottom (1200mm min) level and mark line A. 2. Plum and mark centre line C/L. 3. Measure between bottom of hood to mounting hole and add this dimension line above line A. 4. Mark mounting spread from C/L Y: (measure between two mounting holes). 5. Fasten anchors to wall (see below) as advised by the manufacturer, ensuring they are suitable for the range hood weight 6. Fasten screws or nuts do not fasten all the way. 7. Hang hood and tighten (fig A). A B C/L C/L Duct Cover Bracket Min 1200mm Mounting the Duct Cover Locate and attach the duct cover as required using self tapping screws no longer than 6mm (not supplied) Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards. 1. Centre and attach duct cover mount bracket on wall below ceiling. 2. Fasten telescopic duct covers onto hood and bracket. fig.a Connecting to Power Supply After the range hood is securely installed, route the power cord safely away from all sharp corners and possible entrapments to the power point then plug in and turn on. EZ anchor or Dyna-Bolt Ensure adequate mounting hardware is used (if unsure ask your hardware supplier). 5
MAINTENANCE CLEANING Surface Maintenance Clean periodically with hot soapy water and a clean cotton cloth. Do not use corrosive or abrasive detergent or steel wool/scouring pads which will scratch and damage the surfaces. For heavier deposits, use a liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/cleaners to polish and buff the stainless lustre. Always rub lightly, with a clean cotton cloth and with the grain. Filters The Metal Filters fitted by the factory are intended to filter out residue and grease from cooking. They are required to be kept clean and should be cleaned after every 30 hours of use or more often if required. Remove and clean by hand or in dishwasher. Spray with a degreasing detergent and leave to soak if heavily soiled. Dry filters and re-install before using hood. Replacing filters Should filters wear out due to age and prolonged use, replace with following part number: Product ID: Baffle Filter Description: Stainless Steel Filter Available at http://www.gbi.com.au OPERATION The light is switched on by pressing the corresponding button. Each exhaust fan has three speeds which can be selected by pressing the required button. A blue L.E.D light indicates the selected function. Pressing the selected button again will turn off or alternatively press the off button, OFF HIGH MED FAN LOW LIGHT 6
TECHNICAL INFORMATION MODEL GRHM GRHL Voltage 220-240V AC 220-240V AC Frequency 50Hz 50Hz Motor wattage 2 x 1000W 3 x 1000W Lamp 2 x 12V-1.8W 3 x 12V-1.8W Lamp type L.E.D L.E.D Extraction capacity 2000m 3 /hr 3000m 3 /hr Noise Level 650Dba 650Dba WARRANTY TERMS AND CONDITIONS This warranty is not transferable to a subsequent purchaser if the product is sold by the original purchaser during the warranty period. If a warranty fault appears within the warranty period, S.G.A. reserves the right to replace or repair the product. In the event that S.G.A. chooses to replace the product, this original warranty will expire at the original date. If the product includes various accessories or components, only the defective accessory or component will be replaced or repaired. S.G.A. reserves the right to replace defective parts of the product with parts and components of similar quality, grade and composition where an identical part or component is not available. Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the products. To make a warranty claim, first contact S.G.A's Customer Service Line on the contact number below. The purchase receipt for this product is to be retained and must be presented if making claim under the terms of this S.G.A. warranty. Warranty repairs are free of charge, provided the product is delivered to our Service Department at 33-35 Lionel Road, Mt Waverley, Victoria, 3149 or to one of our Authorised Service Agents. If a warranty fault is found the freight cost will be credited to the owner. If no fault is found the product will be returned and any costs associated with the service will be charged to the owner. Products sent freight forward will not be accepted. In most cases the defective accessory or component only will need to be returned. The product or part of the product being returned must be adequately protected in a box. S.G.A. will not be responsible for any in-transit loss or damage. Continued on page 8 7
This warranty does not apply to any defect, deterioration, loss, injury or damage occasioned by or as a result of misuse or abuse, negligent handling or storage, normal wear and tear or if the product has not been installed and used in accordance with S.G.A.'s instructions, recommendations and specifications or if the product has been subjected to abnormal conditions. The warranty does not apply to blockages caused by insects or living organisms, as well as non-operating butterfly baffles or incorrectly installed ducts. The warranty is void if there is evidence of the product being tampered with by unauthorised persons. The warranty does not extend to installation or disconnection costs. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and Federal legislation that cannot be excluded. Gas Products Approved For Outdoor Use Only For warranty claims, service, spare parts or products information in Australia, please call SITRO GROUP AUSTRALIA Pty Ltd on the Customer Service Line 1300 174 876 A receipt or proof of purchase is required and must be kept for your records. CONTACT DETAILS Sitro Group Australia Pty Ltd 33-35 Lionel Road, Mt. Waverley Victoria 3149, Australia. Tel (+613) 9543 9533 Fax (+613) 9543 9839 sales@sitro.com.au For any queries or assistance call Customer Service (Australia Only) 1300 174 876 Hours of operation: Monday to Friday 8.30am - 5.30pm EST Do not return to place of purchase. Keep your purchase receipt, this will be required to make any claims under the 2 year warranty. Gasmate is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au Aber Ltd - Hamilton, N.Z www.gasmate.co.nz 8