TIMES SQUARE TWO-HANDLE THERMOSTAT

TIMES SQUARE TWO-HANDLE THERMOSTAT MODEL NUMBER: TRIM KITS: T184.740 Two-Handle Thermostat Trim Kit With separate volume control. LESS Valve. ROUGH VALVES: TEMPERATURE & ON/OFF VOLUME CONTROL ONLY R50 Rough Valve Body only* 1/" NPT inlets/outlets. With separate volume control. LESS Trim. R540 Rough Valve Body only* 3/4" NPT inlets/outlets. With separate volume control. LESS Trim. HOT COLD TEMPERATURE & ON/OFF VOLUME CONTROL & BUILT-IN DIVERTER R5 Rough Valve Body only 1/" NPT inlets/outlets. With separate volume control only and built-in -way diverter. LESS trim. R53 Rough Valve Body only 1/" NPT inlets/outlets. With separate volume control only and built-in 3-way diverter. LESS trim. 6-11/16 (170mm) FINISHED WALL 8-1/4" (10mm) HOT COLD 7-3/8" (186mm) 3-7/8" (100mm) R50 1/" NPT INLETS or R540 3/4" NPT INLETS GENERAL DESCRIPTION: 5-7/8" (150mm) Cast brass valve body. The single unit contains two handles, the bottom lever handle sets the desired temperature and the top lever handle functions as an on/off, volume control. The temperature is maintained by a wax element moving a shuttle valve between hot and cold. The volume is controlled by twin ceramic disc valve cartridges. Ceratherm includes Hot Limit Safety Stop. Maximum temperature limit is 11 F. Escutcheon plate is stamped brass. Available with 1/" or 3/4" NPT inlets and outlets. The valve has a high flow rate, ideal for mutiple outlet installations. NOTE: FITTING MUST BE INSTALLED WITH VOLUME CONTROL ON TOP. 1" (5mm) " to -5/8" (48mm to 68mm) PRODUCT FEATURES: Brass Casting: Highest quality faucet material for durability & long life. Wax Thermostatic Unit: Permits shuttle valve to move between the hot and cold seat to maintain the pre-selected constant water temperature. Back to Back Capable: Hot and cold can be reversed. Spring-Loaded Check Valves: When the hot and cold water enters the fitting, both supplies pass through the spring-loaded check valves to prevent cross flow of hot and cold water. Integrated Stop Valves: Ensure easy cleaning and servicing. Adjustable Hot Limit Safety Stop: Limits the amount of hot water allowed to mix with cold. Reduces the risk of accidental scalding. Maximum water temperature limit may be reduced to 104 or 109 degrees Fahrenheit. SUGGESTED SPECIFICATION: Two handle Thermostat shall feature a cast brass valve body. Thermostat shall be a wax element shuttle valve. Shall also feature ceramic disc valving, 1/" NPT or 3/4" NPT inlets and outlets. Fitting shall be American Standard Model # T184.740. (Trim Kit) and R5_ or R540 (Rough Valve). 013 AS America Inc. F3

TIMES SQUARE TWO-HANDLE THERMOSTAT CODES AND STANDARDS These products meet or exceed the following codes and standards: ASSE 1016 ASME A11.18.1 CSA B15 GALLONS PER MINUTE 5 0 15 10 5 FLOW RATE* 3/4" 1/" 0 0 40 60 80 INLET PRESSURE (PSI) *Flow rates shown are for mixed hot and cold. TRIM KITS** Product Number T184.740* Description Two-handle Thermostat Trim Kit with separate volume control. Finish Options PVD Polished Satin Chrome Nickel 00 95 ROUGH VALVE BODIES Product Number R50* Rough Valve Body less trim - 1/" NPT Inlets/Outlets. With separate volume control only. LESS trim. R540* Rough Valve Body less trim - 3/4" NPT Inlets/Outlets. With separate volume control only. LESS trim. R5 R53 Description Rough Valve Body less trim - 1/" NPT Inlets/Outlets. With separate volume control and built-in -way diverter. LESS trim. Rough Valve Body less trim - 1/" NPT Inlets/Outlets. With separate volume control and built-in 3-way diverter. LESS trim. *NOTE: When used as a Bath/Shower a separate diverter valve is required (such as R40 or R430). Requires twin ell (must be ordered separately) for use with diverter spouts. ** ROUGH & TRIM MUST BE ORDERED SEPARATELY. Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for the physically challenged. 013 AS America Inc. F4

TIMES SQUARE CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT Installation Instructions T184.740 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A11.18.1 ASSE 1016 M965506 REV.1.3 (1/15) ROUGHING-IN DIMENSIONS 160mm (6-1/4) FINISHED WALL 10mm (8-1/4) R50 1/" NPT INLETS or R540 3/4" NPT INLETS 186mm (7-3/8) 100mm (3-7/8) 170mm (6-3/4) NOTE: FITTING 5mm MUST BE INSTALLED (1) WITH VOLUME CONTROL ON TOP. 48mm to 68mm ( to -5/8) Recommended Tools Flat Blade Screwdriver Phillips Screwdriver CARE INSTRUCTIONS: To keep your new faucet looking new, please follow these simple care instructions: DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth. DO NOT: Do not use any abrasive cleaners, cloths, or paper towels. Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps. Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended: Remove as much surface dirt and film using clear water and soft cotton cloth (as described above). Use any of the following to remove tough surface film and build-up: Mild liquid detergents Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions. Non-abrasive liquid polishers Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth. Failure to follow these care instructions may damage the Faucet's finish.

1 TRIM INSTALLATION Remove PLASTER GUARD (1) if attached. Push CAPS ( & a) as shown onto CONTROL VALVES (3). Push ESCUTCHEON HOLDER (4) with lightly greased O-RING SEALS (5) over CAPS (, a). 3 4 TOP 1 Attach the FIXATION PLATE (7) to the ESCUTCHEON HOLDER (4) with the two SCREWS (6) provided. Push ESCUTCHEON (8) flush against finished wall. a 5 7 6 8 1 INSTALL HANDLES Thread HANDLE SCREW (1) into VALVE STEM () and tighten to secure KNOB MOUNT (3). Align HANDLE (4) and push onto KNOB MOUNT (3). 3 Tighten SET SCREW (5) in handle with HEX WRENCH (6) SUPPLIED. Install HANDLE ADAPTER (7) onto TEMPERATURE CONTROL KNOB (8) and tighten with SCREW (9). 1 4 Align HANDLE (4a) and push onto TEMPERATURE CONTROL KNOB (8). Tighten SET SCREW (5a) in handle with HEX WRENCH (6) SUPPLIED. 5 4a 8 7 9 5a 6 3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: Shut off water supply. Remove handle and rim. (Reverse steps 1 and ). Remove check stops and re-install them transposed. CHECK STOP (BLUE TO RED) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step 4. Assemble HANDLES and TRIM. CHECK STOP (RED TO BLUE) M965506 REV.1.3 (1/15)

4 TEMPERATURE ADJUSTMENT Loosen SET SCREW (1). Pull off HANDLE ASSEMBLY (). Check that arrow marking B points to the 1 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" 1 o'clock position. See Figure 1. SET HOT LIMIT STOP The maximum mixed water temperature is set at 109 F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Red Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 11 F. For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100 F. Check that arrow "A" on the KNOB MOUNT (3) still points 1 o'clock position after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (3) by pulling it towards you while standing directly in front of the valve. Reinstall the KNOB MOUNT (3) with arrow "A" 1 o'clock position. Reinstall RED LOCKING DEVICE. See Step for HANDLE () installation. Figure 1 ARROWS AT 1 O'CLOCK POSITION 3 KNOB MOUNT TEMPERATURE LIMIT STOP RED LOCKING DEVICE 11 3 109 104 ARROW "B" ARROW "A" 1 BLACK CLAMP M965506 REV.1.3 (1/15)

TIMES SQUARE CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT MODEL NUMBER T184.740 A953961-0070A ESCUTCHEON HOLDER A94335-0070A FIXATION PLATE A907090-YYY0A CAP M918011-0070A HANDLE SCREW 03774-0070A SCREWS Replace the "YYY" with appropriate finish code CHROME SATIN NICKEL 00 95 M90798-YYY0A ESCUTCHEON M918038-0070A ADAPTER M918990-0070A SELF TAPPING SCREW M96446-YYY0A LEVER HANDLE KIT HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-44-190 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-100 Product names listed herein are t rademarks of American S tandard I nc. AS America, Inc. 013 M965506 REV.1.3 (1/15)

SHOWER SYSTEMS SQUARE RAIN SHOWERHEAD MODEL NUMBER: 1660.688 8" Square Rain Showerhead Only 1/" NPT 5mm (") 199mm D. (7-13/16") GENERAL DESCRIPTION: 8" rain showerhead. Brass construction. Drenching rain spray pattern. Includes pressure compensating flow control device. Brass ball joint. Easy clean spray nozzles. 1/" NPT connection..5gpm/9.5l/min. maximum flow rate. PRODUCT FEATURES: Drenching Rain Spray Pattern: Gives the user a drenching shower similar to a rain downpour. Brass Construction: Durable. Easy to clean. Ideal for prolonged contact with water. Pressure Compensating Flow Control Device: Provides consistent flow over a wide pressure range. Easy Clean Spray Nozzles: Easily clean lime and calcium buildup. Nozzles will not clog. SUGGESTED SPECIFICATION Showerhead shall have rain spray pattern and brass ball joint. Showerhead shall have a pressure compensating control device. Fitting shall be American Standard Model # 1660.688.. 01 AS America Inc. F137 1/1

SHOWER SYSTEMS SQUARE RAIN SHOWERHEAD CODES AND STANDARDS FLOW RATE* These products meet or exceed the following codes and standards: ASME A11.18.1 CSA 15.1 GALLONS PER MINUTE 3.0.5.0 1.5 1.0 0.5 0.0 0 40 60 80 100 INLET PRESSURE (PSI) Finish Options Product Number Description Polished Chrome 00 PVD Satin Nickel 95 1660.688 8" Square Rain Showerhead Only Showerhead Accessories Product Number Description 1660.190 1" Ceiling Mount Shower Arm 1660.194 1" Wall Mount Right Angle Shower Arm 1660.191 Square Shower Arm Escutcheon 01 AS America Inc. F138 1/1

SHOWER SYSTEMS WATER SAVING 3-FUNCTION HAND SHOWER * MODEL NUMBER: 1660.144 Water Saving 3-Function Hand Shower *WaterSense approval pending 4mm (9-1/") Ø 100mm (3-7/8") 55mm (-1/8") GENERAL DESCRIPTION: 3-Function hand shower. Hand shower adjusts from full spray to full/massage combination to pulsating massage. Includes pressure compensating flow control device. Includes check valve to prevent cross flow of hot and cold water. Easy clean spray nozzles..0gpm/ 7.6L/min. maximum flow rate. PRODUCT FEATURES: Variety of Spray Patterns: Allows the user to select the type of spray best suited to their needs. Pressure Compensating Flow Control Device: Provides consistent flow over a wide pressure range. Simple Spray Pattern Adjustment: Spray patterns can be changed with a flick of the thumb. Lightweight, Ergonomic Design: For a sure grip even with wet, soapy hands. Easy Clean Spray Nozzles: Easily clean lime and calcium buildup. Nozzles will not clog. SUGGESTED SPECIFICATION Hand Shower shall have at least 3 spray patterns. Hand Shower shall have a pressure compensating flow control device. Hand Shower shall include check valve to prevent cross flow of hot and cold water. Fitting shall be American Standard Model # 1660.144.. 013 AS America Inc. F189

SHOWER SYSTEMS WATER SAVING 3-FUNCTION HAND SHOWER CODES AND STANDARDS These products meet or exceed the following codes and standards: ASME A11.18.1 CSA 15.1 GALLONS PER MINUTE 3.0.5.0 1.5 1.0 0.5 0.0 0 FLOW RATE* 40 60 80 * Flow rate uniform for all spray patterns 100 INLET PRESSURE (PSI) Finish Options Product Number 1660.144 Description Water Saving 3-Function Hand Shower. Polished Chrome 00 Hand Shower Accessories Hand Shower Accessories Product Number Description Product Number Description 8888.035 59" Metal Shower Hose 8888.036 Fixed Wall Bracket 8888.053 79" Metal Shower Hose (Chrome Only) 8888.037 Wall Supply 1660.400 Vacuum Breaker 8888.068 Round Wall Supply 1660.410 Shower Arm Diverter 8888.069 Square Wall Supply 8888.096 Shower Arm Bracket 8888.038 Wall Supply Bracket 013 AS America Inc. F190

Installation Instructions SHOWER SYSTEM ACCESSORIES 8888.068 8888.069 8888.068 8888.069 1660.145 1660.144 8888.035 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Recommended Tools & Materials 1660.145 1660.144 8888.035 Certified to comply with ANSI A11.18.1 M96569 10' Adjustable Wrench Pencil Tape Measure Sealing Tape ROUGHING-IN DIMENSIONS 8888.068 8888.069 1/" NPT 13mm (1/") 0.5mm (13/16") 3mm (1-1/4") 57mm (-1/4") DIA. 1/" NPT 13mm (1/") 0.5mm (13/16") 35mm (1-3/8") 49.5mm (1-15/16") SQ. (48" - 60") (OPTIONAL) TO FINISHED FLOOR 35mm (1-3/8") O-RING GASKET 50mm (") DIA. 1/" NPSM HOSE CONNECTION (48" - 60") (OPTIONAL) TO FINISHED FLOOR 30.5mm (1-3/16") O-RING GASKET 1/" NPSM HOSE CONNECTION FINISHED WALL FINISHED WALL 1 INSTALL WALL SUPPLY CAUTION Turn off hot and cold water supplies before beginning. WALL SUPPLY (1) is 1/" NPT. See rough-in above for detailed information. Install O-RING () onto back of WALL SUPPLY (1). Apply sealant or teflon tape to threads of 1/" NPT supply nipple. Tighten ELBOW (1) onto the inlet pipe nipple with a smooth jaw wrench. WALL SUPPLY (1) should be tight against finished wall. 1/" NPT APPLY SEALANT OR TEFLON TAPE 1/" NPT APPLY SEALANT OR TEFLON TAPE 1 (48" - 60") (OPTIONAL) TO FINISHED FLOOR 1 (48" - 60") (OPTIONAL) TO FINISHED FLOOR

INSTALL HOSE AND HAND SHOWER TO WALL SUPPLY (8888.031 & 8888.03) Install SEAL (1) into SPRAY HOSE END () and connect HAND SHOWER (3) to SPRAY HOSE END (). Hand tighten. Install SEAL (4) into HOSE END (5). Connect HOSE END (5) to WALL SUPPLY (6). Tighten with adjustable wrench. Do not over tighten. Turn on water and test HAND SHOWER (3). 3-FUCTION DIVERTER LEVER 3 1 6 4 5 3 CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800 44-190 Weekdays 8:00 a.m. to 8:00 p.m. EST IN MEXICO 01-800-839-100 IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 01 M96569

EXTENDER MULTIFUNCTION BODY SPRAY MODEL NUMBER: 1660.130 Multifunction Round Body Spray Flush Mount. 1/" NPT Male Connection 6mm (1") 1mm (1/") (75.6-8.6mm) -15/16" - 3-1/4" 15 74mm D. (-15/16") 54mm D. (-1/8") 35mm (1-3/8") FINISHED WALL 57mm D. (-1/4") HOLE SIZE (63.6-70.6mm) -1/" - -3/4" 1/" NPT GENERAL DESCRIPTION: Flush mount body spray. Swivel spray with adjustable spray pattern automatically extends when water is turned on and auto retracts when water is turned off. Spray pattern adjusts from full spray to combination to massage. Spray position adjusts up to 15 in any direction. Easy clean spray nozzles. Brass escutcheon. Fits wall cavity using standard " x 4" studs. Installs as one piece. Plaster guard serves as a rough-in guide and pipe plug. 1.5gpm/5.7L/min. maximum flow rate. PRODUCT FEATURES: Flush Mount: Clean look. Adjustable Spray Pattern: 3 spray options to customize shower experience to personal taste. Simple Spray Adjustment: Spray position adjusts up to 15 in any direction. One Piece Installation: No loose parts to lose or reassemble on site. Easy Clean Spray Nozzles: Easily clean lime and calcium buildup. SUGGESTED SPECIFICATION: Body Spray shall be flush mount to wall projecting no more than 1/" when not in use. Body spray shall have at least 3 spray patterns. Features an automatic swivel spray that extends when water is turned on and retracts when water is turned off. Fitting shall be American Standard Model # 1660.130.. 010 AS America Inc. F117

EXTENDER MULTIFUNCTION BODY SPRAY CODES AND STANDARDS Install as required to comply with local code requirements. ASME A11.18.1 CSA 15 GALLONS PER MINUTE 3 1 FLOW RATE * Flow Rate same for all 3 spray options: Spray, Massage, Combination 0 0 40 60 80 100 I N L E T P R E S S U R E ( P S I ) Finish Options Product Number Description Polished Chrome 00 PVD Blackened Bronze 068 PVD Stainless Steel 075 PVD Satin Nickel 95 1660.130 Extender Multifunction Round Body Spray. 010 AS America Inc. F118

LUXURY SHOWER EXTENDER BODY SPRAYS Installation Instructions 1660.130 1660.140 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Recommended Tools 1660.130 1660.140 Certified to comply with ANSI A11.18.1 M968617 Rev.1. Flat Blade Screwdriver -1/4" DIA. (57mm) Hole Saw Teflon Tape Electric Drill ROUGHING-IN DIMENSIONS ALL CONNECTIONS 1/" NPT 75mm (3") 74mm D. (-15/16") 1660.130 Multifunction Round Body Spray 1660.140 Multifunction Square Body Spray 6mm (1") 1mm (1/") (75.6-8.6mm) -15/16" - 3-1/4" 15 54mm D. (-1/8") 35mm (1-3/8") FINISHED WALL 57mm D. (-1/4") HOLE SIZE (63.6-70.6mm) -1/" - -3/4" 1/" NPT

1 INSTALL SUPPLY PIPING CAUTION Turn off hot and cold water supplies before beginning. Provide a Installation Hole -1/8" - -3/8" DIA., (54-60mm) and 3-1/4", (83mm) deep. Note: The Installation Hole must be clear to allow body spray clearance. Install the ELBOW (1) on a support within the wall at the *dimension shown. Secure with two M5 SCREWS () (not provided). 54-60mm (-1/8" - -3/8" DIA.) 83mm (3-1/4") 54-60mm (-1/8" - -3/8" DIA.) 8.6mm (3-1/4") 1 1 Installation Hole { Installation Hole FINISHED WALL *63.6-70.6mm (-1/" - -3/4") *75.6-8.6mm (-15/16" - 3-1/4") WALL SUPPORT INSTALL PLASTER GUARD Make sure the O-RING (3) is installed on the PLASTER GUARD (1). Install the PLASTER GUARD (1) into ELBOW (). Note: The finished wall must be between the Min. & Max. lines on the PLASTER GUARD (1). Complete all tiling and wall work. When walls are finished remove PLASTER GUARD (1). FINISHED WALL 1 3 3 MAX. (LINE MARK) INSTALL REMOVE 1 MINIMUM (LINE MARK) M968617 Rev.1.

3 INSTALL BODY SPRAY Remove the PLASTER GUARD (1) if not already removed. Make sure the O-RING () and FLANGE GASKET (6) are installed on the BODY SPRAY (3). Thread BODY SPRAY (3) into the ELBOW (4). Tighten BODY SPRAY (3) using WRENCH (5) supplied until flush against finished wall and FLANGE GASKET (6) is compressed. Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation. 6 4 4 3 1 6 3 5 5 FINISHED WALL 4 INSTALL ESCUTCHEON Align ribs on back of ESCUTCHEON (1, ), with slots in BODY SPRAY (3). Push ESCUTCHEON (1, ) against BODY SPRAY (3) until ESCUTCHEON (1, ) snaps into place. Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation. ALIGNMENT RIBS ON BACK OF ESCUTCHEON SLOTS FINISHED WALL 3 1 ALIGNMENT RIBS ON BACK OF ESCUTCHEON 1 5 CARE: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M968617 Rev.1.

LUXURY SHOWER EXTENDER BODY SPRAYS MODEL NUMBERS 1660.130 1660.140 M9686-0070A ELBOW M9685-0070A O-RING M9684-YYY0A BODY SPRAY M9683-YYY0A ESCUTCHEON M968-YYY0A SQUARE ESCUTCHEON KIT M9681-0070A WRENCH Replace the "YYY" with appropriate finish code CHROME BLACKENED BRONZE STAINLESS STEEL OIL RUBBED BRONZE SATIN NICKEL 00 068 075 4 95 M9680-0070A PLASTER GUARD HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-44-190 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-100 Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 009 M968617 Rev.1.

MODEL NUMBER: ROUGH VALVES TWO-HANDLE THERMOSTAT WITH BUILT-IN DIVERTER R5 Rough Valve Body only 1/" NPT inlets/outlets. With built-in -way diverter LESS Trim. R53 Rough Valve Body only 1/" NPT inlets/outlets. With built-in 3-way diverter LESS trim R53 Shown FINISHED WALL PLASTER GUARD 35mm (9-1/4") 196mm (7-3/4") 100mm (3-7/8") 1/" NPT INLETS GENERAL DESCRIPTION: 5mm (1") Cast brass valve body. The single unit contains two handles, the bottom handle sets the desired temperature and the metal top handle controls on/off, volume and diverter functions. The temperature is maintained by a wax element moving a shuttle valve between hot and cold. The volume is controlled by twin ceramic disc valve cartridges. Ceratherm includes Hot Limit Safety Stop. Maximum temperature limit is 11 F. Available with -way or 3-way diverter. 1/" NPT inlets and outlets. 48mm to 68mm (" to -5/8") PRODUCT FEATURES: Brass Casting: Highest quality faucet material for durability & long life. Built-in Diverter: Allows user to choose between or 3 separate shower outlets. Wax Thermostatic Unit: Permits shuttle valve to move between the hot and cold seats to maintain the pre-selected constant water temperature. Back to Back Capable: Hot and cold can be reversed. Spring-Loaded Check Valves: When the hot and cold water enters the fitting, both supplies pass through the spring-loaded check valves to prevent cross flow of hot and cold water. Integrated Stop Valves: Ensure easy cleaning and servicing. Adjustable Hot Limit Safety Stop: Limits the amount of hot water allowed to mix with cold. Reduces the risk of accidental scalding. Maximum water temperature limit may be reduced to 104 or 109 degrees Fahrenheit. SUGGESTED SPECIFICATION: Two handle thermostat shall feature a cast brass valve body. Shall feature built-in diverter. Thermostat shall be a wax element shuttle valve. Shall also feature ceramic disc valving, 1/" NPT inlets and outlets. Fitting shall be American Standard Model # R5_. F19 01 AS America Inc. 5/1

COLD ROUGH VALVES TWO-HANDLE THERMOSTAT WITH BUILT-IN DIVERTER CODES AND STANDARDS These products meet or exceed the following codes and standards: ASSE 1016 ASME A11.18.1 CSA B15.1 Meets the American Disabilities Act Guidelines and ANSI A117.1 Requirements for the physically challenged. GALLONS PER MINUTE 1 10 8 6 4 0 0 FLOW RATE 40 60 80 100 INLET PRESSURE (PSI) *Flow rates shown are for mixed hot and cold. ROUGH VALVE BODIES* Product Number R5 R53 Description Rough Valve Body Less Trim with built-in -way diverter - 1/" NPT inlets/outlets Rough Valve Body Less Trim with built-in 3-way diverter - 1/" NPT inlets/outlets NOTES: * ROUGH & TRIM MUST BE ORDERED SEPARATELY. R5 and R53 will accept the following trims: Town Square Serin Green Tea Copeland AVAILABLE TRIM KITS T555.740 T064.740 Moments Berwick T010.740 T005.740 Portsmouth Quentin HOT T506.740 T430.740 T40.740 T440.740 F0 01 AS America Inc. 5/1

CENTRAL THERMOSTAT WITH BUILT-IN DIVERTER Installation Instructions R5 R53 TOP Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A11.18.1M ASSE 1016 M965394 ROUGHING-IN DIMENSIONS CONNECTIONS ARE: 1/" NPT MODEL NUMBER: R5 Rough Valve Body only 1/" NPT inlets/outlets. With built-in -way diverter MODEL NUMBER: R53 Rough Valve Body only 1/" NPT inlets/outlets. With built-in 3-way diverter 73mm (-7/8) 1/" NPT OUTLETS 1/" NPT OUTLET (R53 ONLY) 1/" NPT OUTLETS FINISHED WALL PLASTER GUARD 100mm (3-15/16) 35mm (9-1/4") 196mm (7-3/4") 100mm (3-15/16) 1/" NPT INLETS 150mm (5-7/8) 1/" NPT INLET 1/" NPT PLUG 5mm (1") 48mm to 68mm (" to -5/8")

1 ROUGHING-IN THE VALVE WARNING DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES. MIXED Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between the minimum and maximum rough dimension. MIXED COLD Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER GUARD is up. Connect the hot and cold water supplies. Assemble all connecting pipes. Flush lines to remove any dirt. Connections are 1/" NPT. Assemble the connection pipes to the MIXED OUTLETS of the VALVE. (Tub port is fitted with a plug at the factory). IMPORTANT! INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES INTO THE PIPING SYSTEM. If the CHECK STOPS (4, 5) were removed during installation, ensure the hot and cold CHECK STOPS (4, 5) are not reversed. The hot CHECK STOP (4) has a red top and the cold CHECK STOP (5) MIXED has a blue top. CHECK STOPS (4,5) are supplied in the open position. Closing using 5/3" (4 mm) hex wrench to pressure test and to check for leaks. To flush lines, remove the CHECK STOPS (4,5) and run water. If desired, the TEMPERATURE CONTROL UNIT can be removed. Reinstall CHECK STOPS (4,5) and CONTROL UNIT (6), if it was removed. Remove PLASTER GUARD () if still installed. Turn on water supplies and check for leaks. Reassemble PLASTER GUARD () and FINISH WALL. HOT 1 3 TUB PORT MIXED MIXED 6 WOOD BRACE MIXED HOT COLD 5 TOP CHECK STOP (COLD BLUE) TOP Beware of Freezing. No water should remain in the MIXING VALVE if freezing is a possibility. Remove the CHECK STOPS (4,5) to completely drain the MIXER UNIT (1). CHECK STOP (HOT RED) 4 TEMPERATURE ADJUSTMENT Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD. Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT and reinstall KNOB MOUNT with arrow "B" pointing upwards. ARROW "B" BLACK CLAMP The maximum mixed water temperature is set at 109 F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 11 F. TEMPERATURE LIMIT STOP For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT until the spout temperature is 100 F. Check that arrow marking A on the KNOB MOUNT still points upward after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve. 104 109 11 SECURING RING RED LOCKING DEVICE ARROW "A" KNOB MOUNT Reinstall the KNOB MOUNT so that the arrow marking A points upwards. 3 Reinstall RED LOCKING DEVICE. TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: Shut off water supply. Remove handle and rim Remove check stops and re-install them transposed. Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. Turn the water supply back on and perform the temperature adjustment in step. CHECK STOP (RED TO BLUE) CHECK STOP (BLUE TO RED) M965394

R5 With two diverter outlets CENTRAL THERMOSTAT WITH BUILT-IN DIVERTER R5 MODEL NUMBER R53 R53 With three diverter outlets M951480-0070A -WAY DIVERTER M951475-0070A 3-WAY DIVERTER M907311-0070A FIXATION NUT 93348-0070A HANDLE ADAPTER 953950-0070A CHECK STOP (COLD BLUE) A95480-0070A THERMOSTAT CARTRIDGE 953963-0070A HANDLE EXTENSION 953951-0070A CHECK STOP (HOT RED) 91647-0070A O-RING 953957-0070A TEMPERATURE CALIBRATION UNIT 963434-YYY0A DEEP ROUGH KIT (SOLD SEPARATELY) HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 44-190 Weekdays 8:00 a.m. to 6:00 p.m. EST IN MEXICO 01-800-839-100 IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. AS America,Inc. 01 M965394