Tender No. B1 Two Stage Continuous Bleaching Range (CBR) Machine Specification Fabric quality :100 to 350 GSM Cotton shirting & Bottom weight(avg GSM=200) Capacity : 90000mtrs per day Roller width : 2000 mm Max. fabric width : 1800 mm Average working speed : 80-90 m/min. Mechanical working speed : 12-120 m/min. 1) Drawing of device with Scray 2 nos. Dragging Roller covered by Synthetic Rubber Fillet and driven by single AC Motor. The speed is variable through AC drive. One Drag Roller is provided with Pressure Rollers. This Drag Roller pull the fabric from trolley which may be in loose strand or in tight strand. 1 No. winch (Star Roller) of special design to deposit the fabric in the Scray. The star Roller is driven. 1 No. SS Grid for Cloth guiding Pile formation of fabric. 1 No. Compensating unit in the Scray. 2) CLOTH ENTRY DEVICE WITH SELVEDGE GUIDERS The guide rollers are made of stainless steel and run in self aligning ball bearings. The tension rods are made of stainless steel. The tension device, worm gear & adjustable handwheel. Selvedge guiders, working pneumatically with mechanical scanning of selvedges, including adjusting spindle and fastening supports. The selvedge guider is centrically adjustable on the adjusting spindle by hand-wheel. 3) DESIZING COMPARTMENT WITH CIRCULATION PUMP & ROTARY FILTER The washing trough and the guide rollers are made of stainless steel and the washing Compartment with a liquor inlet, outlet and overflow. Required Between the lower deflecting rollers flow sheets. The washing compartment must have both sides doors and windows. Required washing compartment, indirect heating system.
Outside bearing of the guide rollers All rollers are running in ball bearings which are installed outside of the washing compartment. Sealing is effected by means of special slide ring seals for bottom rollers and special lip seals for top rollers. Drive of the upper rollers Four of the upper rollers in the closed washing compartment are driven by torque motors. Intermediate Squeezer (Light Nip) The machine frame is made of stainless steel. The squeeze roller and drive roller run in selfaligning roller bearings. The squeeze roller has a soft rubber coating, whereas the drive roller is ebonite covered. The diaphragm with compressed air units. The control of the diaphragm compressed air units is effected by means of a compressed air control unit with reducing valve and manometer. One curved expander roller is mounted in front and back of the nip. The AC-drive motor with flanged-on reduction gear is directly coupled with the drive roller. 4) DESIZE-STEAMER The desize-steamer is completely made of stainless steel. A steam lock is at the entry of the steamer. The guide rollers are made of stainless steel and run in self-aligning ball bearing outside the steam chamber.the sealing is effected by special slip-ring seals, which are maintenance-free. Synchronisation of the speed is effected by compensators. One draw-off reel as well as one plaiting cross for the plaiting down of the cloth onto the retention slat conveyor. The slat conveyor is driven by frequency controlled AC-drive via excenter and thus the cloth is moved through the retention unit. The speed of the excenter movement is variable, and by that the retention time can be adjusted according to the cloth quality. The broad sides are equipped with paned doors, which serve for the observation of the cloth passage within the chamber and also for cleaning purposes. The heating of the chamber is effected by direct steam injection into the sump. The desired temperature can be controlled by an automatic regulator. In order to prevent the formation of drops, the ceiling is very well insulated. 5) OPEN STEAMER EXIT Required grooved expander roller system in order to draw the material in a crease-free way out of the conveyor. The cloth leaves the steamer in the center, selvedge guiders are must required The guiders are mounted on a support and can be adjusted according to the cloth width by means of a hand wheel. 6) Temperature regulator with electro-pneumatic control. Qty-2 no.
7) CLOSED OPEN WIDTH WASHING COMPARTMENTS WITH SINGLE CLOTH THREADING WITH INTERMEDIATE SQUEEZER. Qty-3 no. The washing trough and the guide rollers are made of stainless steel and the washing Compartment with a liquor inlet, outlet and overflow. Required Between the lower deflecting rollers flow sheets. The washing compartment must have both sides doors and windows. Required washing compartment, indirect heating system. Outside bearing of the guide rollers All rollers are running in ball bearings which are installed outside of the washing compartment. Sealing is effected by means of special slide ring seals for bottom rollers and special lip seals for top rollers. Drive of the upper rollers Four of the upper rollers in the closed washing compartment are driven by torque motors. Intermediate Squeezer (Light Nip) The machine frame is made of stainless steel. The squeeze roller and drive roller run in selfaligning roller bearings. The squeeze roller has a soft rubber coating, whereas the drive roller is ebonite covered. The diaphragm with compressed air units.. The control of the diaphragm compressed air units is effected by means of a compressed air control unit with reducing valve and manometer. One curved expander roller is mounted in front and back of the nip. The AC-drive motor with flanged-on reduction gear is directly coupled with the drive roller. The synchronization is regulated by means of swivel compensator. A guide roller is installed in front of the compensator. The rollers are made of stainless steel and are running in ball bearings. 8) CLOSED OPEN WIDTH WASHING COMPARTMENT WITH SINGLE CLOTH THREADING AND HEAVY DUTY SQUEEZER. Qty. 1 no.. The washing trough and the guide rollers are made of stainless steel and the washing Compartment with a liquor inlet, outlet and overflow. Required Between the lower deflecting rollers flow sheets. The washing compartment must have both sides doors and windows. Required washing compartment, indirect heating system. Outside bearing of the guide rollers All rollers are running in ball bearings which are installed outside of the washing compartment. Sealing is effected by means of special slide ring seals for bottom rollers and special lip seals for top rollers. Drive of the upper rollers Four of the upper rollers in the closed washing compartment are driven by torque motors.
Heavy Duty Squeezer (Heavy Nip) The machine frame is made of stainless steel. The squeeze roller and drive roller run in selfaligningroller bearings. The squeeze roller is covered with rubber, whereas the drive roller is covered with ebonite. Required compressed air cylinders. The control of the compressed air cylinders is effected by means of a compressed air control unit with reducing valve and manometer. A curved expander roller is installed in front of the nip. The AC-drive motor with flanged-on reduction gear is directly coupled with the drive roller. 9) OXALIC ACID DOSING SYSTEM 10) TEMPERATURE REGULATOR Qty-4 no. with electro-pneumatic control 11)EXIT SCRAY 1 No. Dragging Roller covered by Synthetic Rubber Fillet and driven by AC Motor. The speed is variable through AC drive. The Drag Roller is provided with Pressure Rollers. 1 No. winch (star Roller) of special design to deposit the fabric in the scray. The star Roller is driven. 1 No. SS Grid for Cloth guiding is provided to regulate pile formation of fabric. 1 No. Compensating unit is provided in the Scray to synchronize the fabric with Batching and plating. 12) CLOTH EXIT DEVICE WITH SELVEDGE GUIDERS The guide rollers are made of stainless steel and run in self aligning ball bearings. The tension rods are made of stainless steel. The tension device, worm gear & adjustable handwheel. Selvedge guiders, system Erhardt & Leimer,, working pneumatically with mechanical scanning of selvedges, including adjusting spindle and fastening supports. The selvedge guider is centrically adjustable on the adjusting spindle by hand-wheel. 13) PLAITING DOWN ARRANGEMENT 14) ELECTRIC SURFACE BATCHER The drive of this surface batcher is effected electrically and controlled by a compensator. The cloth is guided via a guide roller rotating in ball bearings, a curved expander roller and via a batch roller, which is running in ball bearings and is driven. The rollers are made of steel tubes. The batch roller is made of steel and covered with rubber. 15) DRAWING OFF DEVICE WITH SCRAY - ENTRY 16) CLOTH ENTRY DEVICE WITH SELVEDGE GUIDERS
17) CLOSED OPEN WIDTH WASHING COMPARTMENTS WITH SINGLE CLOTH THREADING WITH INTERMEDIATE SQUEEZER. Qty-1 no. As described above in Sr. No.7 above 18) TEMPERATURE REGULATOR Qty-1 no. with electro-pneumatic control 19)IMPREGNATOR The Impregnator is provided with passage of fabric through narrow shafts for turbulence to achieve intensive liquor exchange and uniform distribution of chemicals. The chemicals are penetrated to the core of the fabric for better performance and low chemical consumption. The small quantity of liquor ensures fast liquor refurbishment and short adjustment time at process change. The squeezer is made from rubber rollers and its pressure can be controlled and adjusted so that it ensures :- a. That the fabric always carries enough liquor which is required for one step scouring & bleaching. 20) CHEMICAL DOSING STATION (BLEACHING) a) 5 Dosing pump System Delivering each chemical as per set values in the recipe loaded through Operator panel. b) 5nos. 3-way cock c) Mixing tank d) Automatic valve for water feeding 1 no. e) Flow sensor for water 1 no. f) Recirculation pump for bath liquor. 21) BLEACH-STEAMER COMBINATION The bleach-steamer is completely made of stainless steel. A steam lock is installed at the entry of the steamer. The guide rollers are made of stainless steel and run in self-aligning ball bearings, which are mounted outside of the steam chamber. The sealing is effected by special slip-ring seals, which are maintenance-free. Synchronisation of the speed is effected by compensators. One draw-off reel as well as one plaiting cross for the plaiting down of the cloth onto the retention slat conveyor. The slat conveyor is driven by frequency controlled AC-drive via excenter and thus the cloth is moved through the retention unit. The speed of the excenter movement is variable, and by that the retention time can be adjusted according to the cloth quality. The broad sides are equipped with paned doors, which serve for the observation of the cloth passage within the chamber and also for cleaning purposes. The heating of the chamber is
effected by direct steam injection into the sump. The desired temperature can be controlled by an automatic regulator. In order to prevent the formation of drops, the ceiling is very well insulated. 22) OPEN BLEACH STEAMER EXIT Required grooved expander roller system in order to draw the material in a crease-free way out of the conveyor. The cloth leaves the steamer in the center, selvedge guiders are must required The guiders are mounted on a support and can be adjusted according to the cloth width by means of a hand wheel. 23) CLOSED OPEN WIDTH WASHING COMPARTMENTS WITH SINGLE CLOTH THREADING WITH INTERMEDIATE SQUEEZER. Qty. 3 nos. 24) CLOSED OPEN WIDTH NEUTRALIZING COMPARTMENT WITH SINGLE CLOTH THREADING AND HEAVY DUTY SQUEEZER Qty-1 nos. The washing trough and the guide rollers are made of stainless steel and the washing Compartment with a liquor inlet, outlet and overflow. Required Between the lower deflecting rollers flow sheets. The washing compartment must have both sides doors and windows. Required washing compartment, indirect heating system. Outside bearing of the guide rollers All rollers are running in ball bearings which are installed outside of the washing compartment.sealing is effected by means of special slide ring seals for bottom rollers and special lip seals for top rollers. Drive of the upper rollers Four of the upper rollers in the closed washing compartment are driven by torque motors. Heavy Duty Squeezer (Heavy Nip) The machine frame is made of stainless steel. The squeeze roller and drive roller run in selfaligningroller bearings. The squeeze roller is covered with rubber, whereas the drive roller is covered with ebonite. Required compressed air cylinders. The control of the compressed air cylinders is effected by means of a compressed air control unit with reducing valve and manometer. A curved expander roller is installed in front of the nip. The AC-drive motor with flanged-on reduction gear is directly coupled with the drive roller. 25) TEMPERATURE REGULATOR Qty-5 nos. with electro-pneumatic control
26) ph-display WITH DOSING PUMP Qty-2 nos. The range consists of a circulation pump with the respective circulation line, one measuring electrode at the by-pass of the circulation line, a ph-value-controller with ph-value adjustment and digital ph-value-indicator as well as one suitable dosing pump. J scray & batching system. 27) 24-CYLINDER DRYING RANGE WITH ALTERNATE CYLINDER & HO0D (12 X 2 STACKS, 4 TEFLON COATED, 2 COOLING CYLINDER) Before VDR required additional one J-scray and Heavy Nip. 28) DRAWING OFF DEVICE WITH SCRAY - EXIT 1 No. Dragging Roller covered by Synthetic Rubber Fillet and driven by AC Motor. The speed is variable through AC drive. The Drag Roller is provided with Pressure Rollers. 1 No. winch (star Roller) of special design to deposit the fabric in the Scray. The star Roller is driven. 1 No. SS Grid for Cloth guiding is required to regulate pile formation of fabric. 1 No. Compensating unit is required in the Scray to synchronize the fabric with Batching and plating. 29) CLOTH EXIT DEVICE WITH SELVEDGE GUIDERS The guide rollers are made of stainless steel and run in self aligning ball bearings. The tension rods are made of stainless steel. The tension device, worm gear & adjustable handwheel. Selvedge guiders, system Erhardt & Leimer,, working pneumatically with mechanical scanning of selvedges, including adjusting spindle and fastening supports. The selvedge guider is centrically adjustable on the adjusting spindle by hand-wheel. 30) PLAITING DOWN ARRANGEMENT 31) ELECTRIC SURFACE BATCHER The drive of this surface batcher is effected electrically and controlled by a compensator. The cloth is guided via a guide roller rotating in ball bearings, a curved expander roller and via a batch roller, which is running in ball bearings and is driven. The rollers are made of steel tubes. The batch roller is made of steel and covered with rubber. 32) SWITCH CABINET FOR FREQUENCY CONTROLLED A.C. DRIVE
The switch cabinet is delivered completely wired including all necessary switch gears, fuses and visual signals. 33) One side catwalk for washing compartment. 34) Heat exchanger. 35) Single point utility line to be provided for steam, water, air & condensate.