Item # Quantity C.S.I. Section 11400 CLCS76eN-EGR ENERGY RECOVERY DISHWASHER STANDARD FEATURES Drain Water Energy Recovery (DWER) 22 inch corner power scrapper with 2 HP motor 245 racks per hour Drain water tempering kit (DWT) Opti-RinSe system 30 KW electric booster heater Rapid return conveyor drive mechanism Insulated hinged double doors with door interlock switches Door seal system Pressure regulating valves 19.5 inch chamber height opening Top mounted micro-processer control module Energy saver mode Dirty water indicator Low temperature alert NSF rated configurable Pot and Pan dwell mode Configurable intelligent delime notification Service diagnostics NAFEM Data Protocol compliant Computational fluid dynamic designed selfaligning wash manifolds Stainless steel debossed anti-clogging wash arms Removable integrated pump intake screen Stainless steel self-draining pumps and impellers Single, sloping scrap screen and deep basket Stainless panels enclose perimeter and bottom Door actuated drain closure Single point electrical connection (does not include the booster heater) Vent fan control DIRECTION OF OPERATION Right to Left Left to Right VOLTAGE 8/60/3 240/60/3 380/60/3 480/60/3 600/60/3 MODEL CLCS76eN-EGR Dishwasher OPTIONS AT EXTRA COST Single point electrical connection, to include electric booster three phase only Higher than standard chamber ACCESSORIES Stainless steel vent hoods Canopy exhaust power vent kit Direct drive unloader Blower-dryer Specifications, Details and Dimensions on Inside and Back. Shown with optional vent stack CLCS76eN-EGR ENERGY RECOVERY DISHWASHER F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 1 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER THE ENERGY RECOVERY WAREWASHER IS STANDARD WITH THESE EFFICIENT FEATURES... Inside and out the CLeN-EGR warewashers by Hobart are packed with standard components and design innovations that make them the biggest value in the dishwasher industry. The insulated hinged inspection doors provide easy access in the chamber. Exterior wash pipes and reduced interior baffles reduce clean-up time. The Rapid Return drive allows for a wide separation between the wash and the rinse zone. New, Improved Control Module. The Hobart exclusive microprocessor control module offers a choice of many features, such as an exclusive Energy Saver Mode, NSF rated configurable Pot and Pan dwell mode, Low Temperature Alerts and Dirty Water Indicator. It also displays pertinent machine status and has a configurable intelligent delime notification. The controls have built-in Service Diagnostics and are NAFEM Data Protocol Compliant. Drain Water Energy Recovery (DWeR) is an enhanced energy savings solution that provides % energy savings over the CLe series. DWeR provides this benefit by using the heat from the exiting drain water to warm up the incoming cold water. This heats the cold water prior to filing the booster heater, thus requiring less energy from the booster to reach final rinse temp of 180 for that water. Additionally, by removing this heat from the exiting drain water, and by tempering (cooling) that water (if needed), we help ensure that our customers meet national plumbing codes which require that water be less than 110 as it is passes into external municipality water system. Opti-RinSe. Hobart s exclusive Opti-RinSe significantly reduces operating cost by reducing rinse water and the energy required to heat the water. The unique spray pattern uses large droplets to more efficiently sanitize the ware. Wash Manifolds. Computational Fluid Dynamic designed wash manifolds are self-aligning and come with Hobart s signature debossed anti-clogging nozzles for superior result. Page 2 of 12 Built-in Pressureless Stainless Steel Booster Heater. Interwired and interplumbed. Saves on installation and saves floor space. Simplifies operation with just one switch to power dishmachine and booster. F40479 CLCS76eN-EGR Energy Recovery Dishwasher
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER OTHER STANDARD FEATURES... Thermal Layer Curtains help keep the heat inside the machine. Ball Detent Clutch Conveyor Drive for maximum protection against conveyor jams Integrated Removable Pump Intake Screen to offer the ultimate guard of keeping debris from entering the pump. Hinged Door Seals and stainless steel labyrinth seal for drip-free operation Door Actuated Drain Closure. Closing the door automatically actuates drain closure, eliminates extra manual steps, ensures that closure is in the correct position. AVAILABLE OPTIONS AND ACCESSORIES... Flexibility is synonymous with Hobart CLeN dishwash ers. If your operation demands a dishwasher with a vent hood, an extended hood... a power scrapper, just specify the combination of options that suit your needs. CLCS76eN-EGR Machine Ratings (Mechanical) Racks per hour (19 3 4" x 19 3 4") 245 Conveyor Speed - feet per minute 6.8 max. Dishes per Hour (Average 25 per rack) 6,100 Glasses per Hour (Average 45 per rack) 10,980 Floor Space Table to Table (Inches) 76 Overall Dimensions H x W x D (Inches) 79 9 16 x 89 1 2 x 31 1 4 Motor H.P. Power Scrapper 2 Wash 2 Conveyor Drive H.P. 1 6 Number of Tanks 2 Tank Capacity Gallons Power Scrapper 23 Wash 23 Pump Capacity Gallons per Minute - Weir Test 165 Heating Equipment (For keeping power wash hot) Gas Burners (with Natural Gas) 78,000 BTU per hr. Electric Heating Unit Size Used Booster Heater / Final Rinse KW 30 KW Rinse Minutes operated during hour of maximum operation 60 Final Rinse Flow Gals. per min. At PSI Flow Pressure 2.3 Final Rinse Flow Gals. per hr. MAXIMUM At PSI Flow Pressure 119 At PSI Flow Pressure 138 Rinse PSI Flow Pressure Gal./Rack Hot Water Sanitizing.56-180 F DDU38e Direct Drive Unloader. Center pawl to be connected to dishwasher conveyor by means of a stainless steel adjustable rod. As conveyor drives, center pawl drives racks around 90 degree corner. The DDU38e is designed to move the racks at the same speed as the conveyor dishwasher speed. The DDU38e adds 38" to the length of the machine. OTHER AVAILABLE ACCESSORIES... Blower-dryer, direct drive unloader. Steam Consumption Pounds per hr. - MAXIMUM Approx. 30 lbs. per hr. = 1 boiler H.P. (BHP) Dishwasher, based on PSI steam and on customer supplying final rinse water at 180 F maximum 65 Exhaust Requirements Cubic Feet per minute Entrance End 0 Discharge End 400 Peak Rate of Drain Flow Gallons per minute. (Initial rate with full tank) 38 Shipping Weight Crated Approximate lbs. 943 F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 3 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER 40 9/16" 76 7/16" 10" 36 5/8" OPTIONAL VENT HOODS W/DAMPER OPTIONAL EXTENDED VENT HOODS W/DAMPER 4 3/4" 11 1/4" 19 1/2" 1/2" 65 9/16" 1/4" OPENING L-R OPER 68 1/2" 34" 8 7/8" 24 7/16" 5/8" 40 1/16" 22" MAY BE DRAINED TO EITHER SIDE OF VALVE, PLUG OPPOSITE SIDE. 1 5/16" DRAIN WATER ENERGY RECOVERY CAUTION: CERTAIN MATERIALS INCLUDING SILVER, ALUMINUM, AND PEWTER ARE ATTACKED BY SODIUM HYPOCHLORITE (LIQUID BLEACH). ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. 19 11/16" ATTN: PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY, AND PLUMBING CODES. 65 1/2" 58 1/2" 14 1/2" 18 5/8" WALL FLUE FOR GAS HEAT BOOSTER HEAT 30 KW MINIMUM ELEC. RATED SUPPLY MAXIMUM SPECS. AMPS CIRCUIT PROTECTIVE CONDUCTOR DEVICE AMPACITY 380-4/50/3 53.2 60 60 0/50/3 80.8 90 90 8/60/3 83.9 90 90 240/60/3 80.2 90 90 380/60/3 42.5 60 60 480/60/3 40.1 50 50 600/60/3 33.7 40 40 3" MIN. FLUE Page 4 of 12 F40479 CLCS76eN-EGR Energy Recovery Dishwasher
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER OPTIONAL VENT HOODS W/DAMPER OPTIONAL EXTENDED VENT HOODS W/DAMPER D 10" 36 5/8" 76 7/16" 40 9/16" 4 3/4" 11 1/4" 1/2" 19 1/2" 68 1/2" D 34" R-L OPER 1/4" OPENING 65 9/16" 8 7/8" DRAIN WATER ENERGY RECOVERY MAY BE DRAINED TO EITHER SIDE OF VALVE, PLUG OPPOSITE SIDE. SEAL (MUST BE WATERTIGHT) A B B 11 1/16" 31 3/4" 18 1/2" A 22 1/32" OUTSIDE CHAMBER 21 19/32" INSIDE CHAMBER 0 / 3/8" 3 HOLES 11 1/32" 1/16" 11/16" 2 1/32" 1 5/16" 40 1/16" REF 22" 5/8" 1 5/16" 19" SECTION A-A BLEND ROLL HERE C C 11/16" 19 11/16" SECTION C-C 30" OR TO DESIRED CUSTOMER'S TABLE DIMENSION 1" ROLL USE SILICONE SEALER BETWEEN TABLE AND CHANNEL OF CHAMBER TO PREVENT LEAKAGE SECTION B-B LOAD END CLCS-22e CHAMBER VIEW D-D 8" AVG 3/8" 3" 1 1/4" FRONT OF MACHINE MACHINE 22" INSIDE TANK VIEW SHOWING HOLE LOCATIONS IN TURNED DOWN PORTION OF TABLE 2 HOLES FOR BOLTING TABLE TO TANK 3/8" 3" 27" WIDTH OF MACHINE 14 1/2" WIDTH OF TRACKS " 11" SUGGESTED TRACK AND TABLE LAYOUT UNLOAD END 27" AVG INSIDE TABLE WIDTH TRACK HEIGHT ABOVE TANK LIP 1/4" - 5/16" SECTIONAL VIEW SHOWING TABLE CONNECTIONS 1 1/4" 7/8" USE SILICONE SEALER BETWEEN TABLE AND LIP OF TANK TO PREVENT LEAKAGE F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 5 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER ELECTRI-R 38 5/8" 36 1/16" 11 7/16" 6 7/8" 6 3/16" 29 5/16" 19 3/16" 3/8" MODEL: CLCS76eN ENERGY RECOVERY L-R OPERATION E-9748 REV B EXHAUST 4" X 16" 3 9/16" BOOSTER 3 7/16" 4" 4 1/4" DWT 5/8" 3/8" 4 3 11 1/2" CHEMICAL PORTS 10 1/2" 12 3/8" DWER 5 1/2" 23" OPEN DOOR E4 E5 12" MIN FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) MISCELLANEOUS NOTES: OPTIONAL VENT HOODS OR EXTENDED HOODS EXHAUST REQUIREMENTS: 0 CFM ENTRANCE END 400 CFM EXIT END. ALL DIMENSIONS TAKEN FROM FLOOR LINE MAY BE INCREASED APPROXIMATELY 3/4" OR DECREASED 1/2". NET WEIGHT OF MACHINE: 8 LBS (STD HEIGHT), DOMESTIC SHIPPING WEIGHT: 926 LBS (STD HEIGHT). CLeN LATENT AND SENSIBLE HEAT DISSIPATION INFORMATION ON F40459. PLUMBING NOTES: WATER HAMMER ARRESTOR (MEETING ASSE-1010 STANDARD OR EQUIVALENT) TO BE SUPPLIED (BY OTHERS) IN COMMON WATER SUPPLY LINE AT SERVICE CONNECTION. RECOMMENDED WATER HARDNESS TO BE 3 GRAINS OR LESS FOR BEST RESULTS. FOR NON-BOOSTER MACHINE (P6 CONN): RECOMMENDED BUILDING FLOWING WATER PRESSURE TO THE DISHWASHER IS PSI, ( PSI MIN - 25 PSI MAX). IF PRESSURES HIGHER THAN 25 PSI ARE PRESENT, A PRESSURE REGULATING VALVE WITH INTERNAL THERMAL EXPANSION BY-PASS MUST BE SUPPLIED (BY OTHERS) IN THE WATER LINE TO THE DISHWASHER. FOR CONVENIENCE WHEN CLEANING, WATER TAP SHOULD BE INSTALLED NEAR MACHINE WITH HEAVY DUTY HOSE AND SQUEEZE VALVE. WHEN USED, CHEMICAL SANITIZING FEEDER MUST BE CERTIFIED TO NSF STANDARD 29. SINGLE POINT ELECTRICAL CONNECTION (3 PH ONLY) MOTORS AND ELECTRIC TANK HEAT VOLTAGE RATED AMPS MINIMUM SUPPLY CIRCUIT CONDUCTOR AMPACITY MAXIMUM PROTECTIVE DEVICE 8/60/3 60.6 80 80 240/60/3 58 80 80 480/60/3 30.6 40 40 0/50/3 60 80 80 380/60/3 33.5 40 40 380-4/50/3 34.9 40 40 600/60/3 22.6 35 35 SEPARATE SERVICE CONNECTION FOR ELEC. HEAT ELEC. HEAT KW (WASH) VOLTAGE RATED AMPS MINIMUM SUPPLY CIRCUIT CONDUCTOR AMPACITY 8/60/3 45 60 240/60/3 43 60 480/60/3 22 30 0/50/3 43 60 380/60/3 23 30 380-4/50/3 29 40 600/60/3 14.4 8/60/1 78 100 240/60/1 74.4 100 MAXIMUM PROTECTIVE DEVICE 60 60 30 60 30 40 100 100 SEPARATE SERVICE CONNECTION FOR MOTORS ON ELEC. HEAT MOTORS: 1/6 HP CONVEYOR 2 HP WASH VOLTAGE RATED AMPS 8/60/3.6 240/60/3.1 480/60/3 9.1 0/50/3 16.6 380/60/3 10.7 380-4/50/3 10.1 600/60/3 8.2 8/60/1 27 240/60/1 26.3 MINIMUM SUPPLY CIRCUIT CONDUCTOR AMPACITY 35 35 MAXIMUM PROTECTIVE DEVICE 35 35 Page 6 of 12 F40479 CLCS76eN-EGR Energy Recovery Dishwasher
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER ELECTRIC R-L 19 3/16" 3/8" 11 7/16" 6 3/16" 29 5/16" 4" 39 1/8" 36 1/16" 14 9/16" MODEL: CLCS76eN ENERGY RECOVERY R-L OPERATION E-974814 REV B 11 1/2" CHEMICAL PORTS 3 9/16" BOOSTER 4 3 3 7/16" 1/8" EXHAUST 4" X 16" 4 1/4" DWT 5/8" 12 3/8" DWER 5 1/2" 10 1/2" 23" OPEN DOOR E4 E5 12" MIN FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) ELECTRICAL CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND ELECTRIC CONNECTION: SINGLE POINT, ELEC, GAS, & STEAM, 1-1/4" CONDUIT HOLE OR 2" CONDUIT, 63-3/4" AFF ELECTRIC CONNECTION: BOOSTER. KW/30KW, 1-1/4" CONDUIT HOLE OR 2" CONDUIT HOLE, 63-3/4" AFF ELECTRIC CONNECTION: DETERGENT, SANITIZER (LOW TEMP ONLY) AND RINSE FEEDERS. 1/2" CONDUIT. 64-1/4" AFF ELECTRIC HEAT ONLY SINGLE PHASE OR FIELD CONFIGURED 3 PHASE SEPARATE ELECTRIC CONNECTION E4 ELECTRIC CONNECTION: MOTORS AND CONTROLS 1-1/4" CONDUIT. 63-3/4" AFF. E5 ELECTRIC HEAT:,000 WATTS, WASH TANK. 1" CONDUIT HOLE, 63-3/4" AFF. 3 4 PLUMBING CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND DRAIN: 2" FPT, 7-3/8" AFF TWO POSSIBLE CONNECTIONS; MAY BE DRAINED TO EITHER SIDE OF VALVE, PLUG OPPOSITE SIDE. RINSE FEEDER: REMOVE 1/8" NPT PIPE PLUG TO ACCESS TAPPED HOLE. 1/8" NPT 59-9/16" AFF. DETERGENT PROBE SENSOR: REMOVE CAP AND STUD ASSEMBLY TO ACCESS 7/8" DIA HOLE (WASH TANK ONLY). 14-5/8" AFF. INDIRECT DRAIN-FLOOR SINK: BY OTHERS, 0" AFF. WHEN REQUIRED, INSTALL FLOOR SINK OUTSIDE THE PERIMETER OF THE DISHWASHER. HOT WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. HIGH TEMP, W/30K BOOSTER 110 F MIN. COLD WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. COLD TEMP, 55 F MIN. F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 7 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER GAS L-R LC 38 5/8" 36 1/16" 29 5/16" 11 7/16" 19 3/16" EXHAUST 4" X 16" 4 1/4" DWT 5/8" 6 7/8" 3 9/16" BOOSTER 3 7/16" 3/8" 4" 1/4" 4 3/8" 3 11 1/2" CHEMICAL PORTS 10 1/2" LC 12 3/8" DWER 5 1/2" 2 5/8" 23" OPEN DOOR 1 0 12" MIN FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) MISCELLANEOUS NOTES: OPTIONAL VENT HOODS OR EXTENDED HOODS EXHAUST REQUIREMENTS: 0 CFM ENTRANCE END 400 CFM EXIT END. ALL DIMENSIONS TAKEN FROM FLOOR LINE MAY BE INCREASED APPROXIMATELY 3/4" OR DECREASED 1/2". NET WEIGHT OF MACHINE: 8 LBS (STD HEIGHT), DOMESTIC SHIPPING WEIGHT: 926 LBS (STD HEIGHT). CLeN LATENT AND SENSIBLE HEAT DISSIPATION INFORMATION ON F40459. SERVICE CONNECTION FOR MOTORS AND CONTROLS MOTORS: 1/6 HP CONVEYOR 2 HP WASH MINIMUM VOLTAGE RATED SUPPLY MAXIMUM AMPS CIRCUIT PROTECTIVE CONDUCTOR DEVICE AMPACITY 8-240/60/3 16.3 380/60/3 11.1 480/60/3 9.4 600/60/3 8.4 8-240/60/1 27.9 35 35 PLUMBING NOTES: WATER HAMMER ARRESTOR (MEETING ASSE-1010 STANDARD OR EQUIVALENT) TO BE SUPPLIED (BY OTHERS) IN COMMON WATER SUPPLY LINE AT SERVICE CONNECTION. RECOMMENDED WATER HARDNESS TO BE 3 GRAINS OR LESS FOR BEST RESULTS. FOR NON-BOOSTER MACHINE (P6 CONN): RECOMMENDED BUILDING FLOWING WATER PRESSURE TO THE DISHWASHER IS PSI, ( PSI MIN - 25 PSI MAX). IF PRESSURES HIGHER THAN 25 PSI ARE PRESENT, A PRESSURE REGULATING VALVE WITH INTERNAL THERMAL EXPANSION BY-PASS MUST BE SUPPLIED (BY OTHERS) IN THE WATER LINE TO THE DISHWASHER. FOR CONVENIENCE WHEN CLEANING, WATER TAP SHOULD BE INSTALLED NEAR MACHINE WITH HEAVY DUTY HOSE AND SQUEEZE VALVE. WHEN USED, CHEMICAL SANITIZING FEEDER MUST BE CERTIFIED TO NSF STANDARD 29. GAS HEAT ONLY FOR NATURAL GAS, PRESSURE TO THE BURNER (CUSTOMER CONNECTION) SHOULD BE 3.5" MIN, 7" MAX W.C. FOR LP GAS, PRESSURE TO THE BURNER (CUSTOMER CONNECTION) SHOULD BE 8" MIN, 11" MAX. W.C. IF GAS PRESSURE IS HIGHER THAN 7"(NAT) OR 11"(LP) W.C., A PRESSURE REGULATING VALVE MUST BE INSTALLED (BY OTHERS) IN THE GAS LINE TO THE DISHWASHER. GAS HEAT (NATURAL OR LP) BTU/HR INPUT - 78,000. GAS EXHAUST VENTING MUST BE INSTALLED ACCORDING TO LOCAL CODE. DO NOT CONNECT FLUE TO POWER VENT. SEE INSTALLATION MANUAL FOR GAS VENTING. Page 8 of 12 F40479 CLCS76eN-EGR Energy Recovery Dishwasher
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER GAS R-L 39 1/8" 19 3/16" 3/8" 11 7/16" 29 5/16" 4" 36 1/16" 14 9/16" 12 1/4" 11 1/2" CHEMICAL PORTS 3 9/16" BOOSTER 4 3 3 7/16" 1/8" EXHAUST 4" X 16" 4 1/4" DWT 5/8" 2 5/8" 12 3/8" DWER 10 1/2" 5 1/2" 0 23" OPEN DOOR 1 12" MIN FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) ELECTRICAL CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND ELECTRIC CONNECTION: SINGLE POINT, ELEC, GAS, & STEAM, 1-1/4" CONDUIT HOLE OR 2" CONDUIT, 63-3/4" AFF ELECTRIC CONNECTION: BOOSTER. KW/30KW, 1-1/4" CONDUIT HOLE OR 2" CONDUIT HOLE, 63-3/4" AFF ELECTRIC CONNECTION: DETERGENT, SANITIZER (LOW TEMP ONLY) AND RINSE FEEDERS. 1/2" CONDUIT. 64-1/4" AFF 0 1 3 4 PLUMBING CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND DRAIN: 2" FPT, 7-3/8" AFF TWO POSSIBLE CONNECTIONS; MAY BE DRAINED TO EITHER SIDE OF VALVE, PLUG OPPOSITE SIDE. RINSE FEEDER: REMOVE 1/8" NPT PIPE PLUG TO ACCESS TAPPED HOLE. 1/8" NPT 59-9/16" AFF. DETERGENT PROBE SENSOR: REMOVE CAP AND STUD ASSEMBLY TO ACCESS 7/8" DIA HOLE (WASH TANK ONLY). 14-5/8" AFF. INDIRECT DRAIN-FLOOR SINK: BY OTHERS, 0" AFF. WHEN REQUIRED, INSTALL FLOOR SINK OUTSIDE THE PERIMETER OF THE DISHWASHER. GAS HEAT ONLY GAS CONNECTION - NAT., 1/2" FPT, 10-3/4" AFF; 3.5" MIN, 7" MAX W.C. INCOMING. GAS CONNECTION - L.P., 1/2" FPT, 10-3/4" AFF; 8" MIN, 11" MAX W.C. INCOMING. HOT WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. HIGH TEMP, W/30K BOOSTER 110 F MIN. COLD WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. COLD TEMP, 55 F MIN. F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 9 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER STEAM L-R EXHAUST 4" X 16" 38 5/8" 36 1/16" 11 7/16" 7 1/4" 6 7/8" 3 9/16" BOOSTER 3 7/16" 29 5/16" 5" 4" 19 3/16" 3/8" 4 1/4" DWT 5/8" 10 1/2" 3/8" 4 3 11 1/2" CHEMICAL PORTS 4 9/16" 5 1/2" 12 3/8" DWER 10 5/16" 23" OPEN DOOR P8 P9 12" MIN FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) MISCELLANEOUS NOTES: OPTIONAL VENT HOODS OR EXTENDED HOODS EXHAUST REQUIREMENTS: 0 CFM ENTRANCE END 400 CFM EXIT END. ALL DIMENSIONS TAKEN FROM FLOOR LINE MAY BE INCREASED APPROXIMATELY 3/4" OR DECREASED 1/2". NET WEIGHT OF MACHINE: 8 LBS (STD HEIGHT), DOMESTIC SHIPPING WEIGHT: 926 LBS (STD HEIGHT). CLeN LATENT AND SENSIBLE HEAT DISSIPATION INFORMATION ON F40459. SERVICE CONNECTION FOR MOTORS AND CONTROLS MOTORS: 1/6 HP CONVEYOR 2 HP WASH VOLTAGE RATED AMPS MINIMUM SUPPLY CIRCUIT CONDUCTOR AMPACITY 0-240/50/3 16.6 8-240/60/3 16.3 380-4/50/3 10.1 380/60/3 11.1 480/60/3 9.4 600/60/3 8.4 8-240/60/1 27.9 35 MAXIMUM PROTECTIVE DEVICE 35 PLUMBING NOTES: WATER HAMMER ARRESTOR (MEETING ASSE-1010 STANDARD OR EQUIVALENT) TO BE SUPPLIED (BY OTHERS) IN COMMON WATER SUPPLY LINE AT SERVICE CONNECTION. RECOMMENDED WATER HARDNESS TO BE 3 GRAINS OR LESS FOR BEST RESULTS. FOR NON-BOOSTER MACHINE (P6 CONN): RECOMMENDED BUILDING FLOWING WATER PRESSURE TO THE DISHWASHER IS PSI, ( PSI MIN - 25 PSI MAX). IF PRESSURES HIGHER THAN 25 PSI ARE PRESENT, A PRESSURE REGULATING VALVE WITH INTERNAL THERMAL EXPANSION BY-PASS MUST BE SUPPLIED (BY OTHERS) IN THE WATER LINE TO THE DISHWASHER. FOR CONVENIENCE WHEN CLEANING, WATER TAP SHOULD BE INSTALLED NEAR MACHINE WITH HEAVY DUTY HOSE AND SQUEEZE VALVE. WHEN USED, CHEMICAL SANITIZING FEEDER MUST BE CERTIFIED TO NSF STANDARD 29. STEAM HEAT ONLY FLOWING STEAM PRESSURES ABOVE 50 PSI MUST HAVE A PRESSURE REGULATOR (BY OTHERS) INSTALLED IN THE STEAM LINE. SHUT OFF VALVE MUST BE SUPPLIED (BY OTHERS) IN THE STEAM LINE TO THE DISHWASHER. Page 10 of 12 F40479 CLCS76eN-EGR Energy Recovery Dishwasher
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER STEAM R-L 11 1/2" CHEMICAL PORTS 3 9/16" BOOSTER 19 3/16" 3/8" 11 7/16" 4 3 29 5/16" 18" 4" 39 1/8" 36 1/16" 14 9/16" 5 3/4" 3 7/16" 1/8" EXHAUST 4" X 16" 4 1/4" DWT 5/8" 12 3/8" DWER 4 9/16" 5 1/2" 10 1/2" 23" OPEN DOOR P8 P9 12" MIN 10 5/16" FLOOR SINK (BY OTHERS) " SERVICE (BOTH SIDES) PLUMBING CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND ELECTRICAL CONNECTIONS CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND ELECTRIC CONNECTION: SINGLE POINT, ELEC, GAS, & STEAM, 1-1/4" CONDUIT HOLE OR 2" CONDUIT, 63-3/4" AFF ELECTRIC CONNECTION: BOOSTER. KW/30KW, 1-1/4" CONDUIT HOLE OR 2" CONDUIT HOLE, 63-3/4" AFF ELECTRIC CONNECTION: DETERGENT, SANITIZER (LOW TEMP ONLY) AND RINSE FEEDERS. 1/2" CONDUIT. 64-1/4" AFF P8 P9 3 4 DRAIN: 2" FPT, 7-3/8" AFF TWO POSSIBLE CONNECTIONS; MAY BE DRAINED TO EITHER SIDE OF VALVE, PLUG OPPOSITE SIDE. RINSE FEEDER: REMOVE 1/8" NPT PIPE PLUG TO ACCESS TAPPED HOLE. 1/8" NPT 59-9/16" AFF. DETERGENT PROBE SENSOR: REMOVE CAP AND STUD ASSEMBLY TO ACCESS 7/8" DIA HOLE (WASH TANK ONLY). 14-5/8" AFF. INDIRECT DRAIN-FLOOR SINK: BY OTHERS, 0" AFF. WHEN REQUIRED, INSTALL FLOOR SINK OUTSIDE THE PERIMETER OF THE DISHWASHER. STEAM HEAT ONLY STEAM COILS: 10 TO 50 PSI FLOWING, 3/4" FPT, 11-1/8" AFF. CONDENSATE RETURN: A 10 PSI MINIMUM DIFFERENTIAL PRESSURE ACROSS THE STEAM TRAP MUST BE MAINTAINED. 3/4" FPT. 11-1/8" AFF ONE CONNECTION. (ONE BUCKET TYPE TRAP FURNISHED). HOT WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. HIGH TEMP, W/30K BOOSTER 110 F MIN. COLD WATER CONNECTION: 1/2" FPT, 11-3/16" AFF. COLD TEMP, 55 F MIN. F40479 CLCS76eN-EGR Energy Recovery Dishwasher Page 11 of 12
CLCS76eN-EGR ENERGY RECOVERY DISHWASHER SPECIFICATIONS: Meets requirements of A.S.S.E. Standard No. 1004. DESIGN: Semi automatic, high temperature single-tank, racktype dishwasher with flexible thermal layer curtains at the ends of chamber and between wash and final rinse zones. Insulated hinged inspection doors located in front of machine provide easy access to wash arms, rinse arms, strainer, strainer basket, and pump intake screen. Length of machine inside tank (at table connection) 76". Machine designed to clean and sanitize with hot water 160 F wash and 180 F (minimum) final rinse. Water hardness recommended to be 3 gr. or less for best results. Automatic interlocks shut off pump and conveyor if door is opened when machine is in operation. CONSTRUCTION: Tank, chamber, frame, legs, control box, doors, and all panels are constructed of stainless steel. PUMPS: Two recirculating stainless steel pumps and impellers with ceramic seat seals. Easily accessible pump assembly permits quick inspection. The pump is self-draining. All piping distributing water to the upper and lower wash arms is stainless steel tubing. PUMP MOTOR: Built for Hobart 2 hp grease-packed ball bearings, splash proof, ventilated with manual, resettable inherent overload protection. Available in electrical specifications of 8-240/60/3, 480/60/3 and 600/60/3. Also available, but not submitted for UL listing are 0-240/50/3 and 380-4/50/3. CONTROLS: A stainless steel control module with power and start/stop buttons is mounted on top of the machine. Machine control circuitry will be operated from a 1-volt control circuit transformer. Electrical components are completely wired with 105 C, 600V thermoplastic insulated wire with stranded conductors routed through UL listed electrical conduit or covered wire way. CONVEYOR: Rapid Return drive, designed for more even throughput of racks and allows for a 16-inch sepa ration between the wash and the rinse zone. Racks conveyed automatically through wash and rinse zones. Ball Detent Clutch drive prevents damage to machine or racks, should movement of racks be obstructed. Conveyor speed: 6.8 FPM. DRIVE MOTOR: Built for Hobart, 1 6 horsepower gear motor, ventilated with manual, resettable inherent overload protection. Available in electrical specifications of 8-240/60/3, 480/60/3 and 600/60/3. Also available, but not submitted for UL Listing are 0-240/50/3 and 380-4/50/3. CORNER POWER SCRAPPER: CLCS76eN power scrapper is equipped with an upper and lower wash arm with specially shaped nozzles having large openings and arranged to effectively scrap all types of tableware. Power scrapper arms and end caps are easily removable for cleaning without use of tools. Removable perforated stainless steel strainer pans support a deep perforated stainless steel basket. Basket and strainer pans (3) can be removed without lower wash arm removal. POWER WASH: Wash tank is equipped with upper and lower stainless steel CFD Wash Arms which effectively direct water jets to all ware surfaces. Both upper and lower wash arms are selfaligning and have easily removable end caps for cleaning without use of tools. A removable perforated stainless steel strainer pan supports a deep perforated stainless steel basket. FINAL RINSE: Final rinse flow rate: 2.1 gpm,.56 gpr, 138-gph. Stainless steel upper and lower Auto Position Rinse Arms have single rows of nozzles. Racks entering the rinse zone automatically trigger rinse. Final rinse water line is equipped with a vacuum breaker downstream of an electrically operated solenoid valve in common piping system. Rinse agent dispenser injection ports provided in final rinse piping above chamber. FILL: Fill water line is equipped with vacuum breaker on downstream side of electrically operated solenoid valve in common piping system, for automatic maintenance of tank level. DRAIN AND OVERFLOW: Large bell-type automatic overflow and drain valve inside power scrapper tank controlled from inside of machine. Power scrapper overflows to drain. Wash tank drain controlled from inside of the machine overflows to power scrapper through large internally mounted stainless steel tubing. Drain seals are large diameter high temperature o-rings. Drain automatically seats by closing inspection doors. Common drain utilizes a removable large diameter stainless steel tube sealed by rubber o-rings at each drain housing. Drain housing can be plumbed from load or unload end of machine. STANDARD EQUIPMENT: Energy Recovery, Digital display of wash and final rinse temperature. Positive low water protection for tank heat. Thermal Layered Curtains throughout machine are keyed to ensure proper placement. Drains are automatically closed when inspection doors are closed. Stainless steel adjustable feet. Bolted stainless steel enclosure panels around perimeter and underneath machine. Automatic tank fill. Door interlocks. Auto-timer. Vent fan and booster heater controls. Low temperature alerts. Service diagnostics. Dirty water indicator. Configurable intelligent delime notification. NSF rated configurable Pot and Pan dwell mode. Energy Saver Mode. NAFEM Data Protocol compliant. Pressure regulating valve. Booster heater (30 kw). WASH TANK HEATING SELECTIONS (must choose one): ELECTRIC: One electric Incoloy sheathed immersion heater ( KW) removable from inside tank. Tank water temperature is controlled by microprocessor controlled thermostat with positive low-water protection and magnetic contactor. (Disconnect switches not furnished.) A high limit device mounted on the surface of the tank additionally protects heating element. STEAM: One-inch stainless steel steam coil. Tank water temperature controlled by microprocessor controlled thermostat with positive low-water protection. Steam supplied to machine through high temperature steam solenoid valve and line strainer. GAS: Regulated infrared immersion tube gas burner system. Microprocessor controlled thermostat and a blower with a pressure switch control tank water temperature. Positive low water protection is provided. A high limit device mounted on the surface of the tube additionally protects immersion tube. A solid-state igniter board controls the gas valve and provides flame ignition. A transformer steps the control circuit voltage down from 1 volts to 24 volts to power the igniter board and gas valve. For natural gas, gas pressure to burner (customer connection) not to exceed 7" W.C. For LP gas, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C. natural or 11" W.C. LP pressure regulating valve must be supplied (by others) in the gas line to the dishwasher. OPTIONAL EQUIPMENT AT EXTRA COST: Stainless steel vent hoods with vent stack, and locking-type damper (load end only). Canopy exhaust power vent kit. Higher than standard chamber. Side loaders and unloaders. 19 3 4" x 19 3 4" peg, combination and miscel laneous racks. Table limit switch. As continued product improvement is a policy of Hobart, specifications are subject to change without notice. Page 12 of 12 F400479 (REV. 05/17) F40479 CLCS76eN-EGR Energy Recovery Dishwasher LITHO IN U.S.A. (H-01)