INSTRUCTION MANUAL. Bar-B-Chef Electric BBQ Code No: BBQE Model No:KYS-367S. Read these instructions thoroughly before first use

Transcription

1 INSTRUCTION MANUAL Bar-B-Chef Electric BBQ Code No: BBQE Model No:KYS-367S Read these instructions thoroughly before first use

2 Before use Please read these instructions carefully. They will give you important advice for the use, security and maintenance of this appliance. Keep these instructions and, should the situation arise, pass them on to other users. The appliance must only be used for the intended purpose according to these instructions. Observe any local regulations. Dispose of the packaging thoughtfully. Safety regulations Plug the appliance only in conventional 240V AC domestic outlets as mentioned on the rating plate and only into regular earthed, three-pin sockets. An electric appliance is not a children s toy. Children are not aware of the hazards of electrical appliances. Therefore close supervision is necessary when the appliance is used by children. Do not allow power cable to hang down within easy reach. Keep children away from packing material, e.g. plastic bags. The installation of a faulty current protective device with a rated breaking current offers you additional safety by ensuring that 30 ma will not be exceeded in the house installation. Get more advice on this from your electrician. Danger also exists with appliances which have been switched off, so after use, the plug should always be removed for the mains. Do not use this appliance within reach of water contained in bath-tubs, washbasins or other Receptacles. Never expose it to rain, snow or other moisture. Regularly check whether the power cord is defective. In this case the appliance must not be put into operation (immediately disconnect the plug). Consult your store of purchase for advice. The appliance must not be operated (disconnect the mains plug immediately) when: the appliance, casing or power cord is damaged the appliance shows visible signs of damage. a fault is suspected after the appliance has been dropped or similar Switch off all the power point and disconnect the main plug: in case of faults during use. before cleaning or moving the appliance from place to place. after use Never pull the plug out of the socket by the power cord or with wet hands. Never carry nor pull the appliance by the power cord. Don t pull the power cord over sharp edges. Don t wedge (eg under doors etc.). Never immerse the power cord or the thermostat plug in water or any other liquid.

3 Only use extension leads after having made sure that their condition is faultless and use an earthed cable with a minimum capacity of 10A. Positon the power cord and cable so that unintentional touching or catching is impossible. Never allow the extension lead or power cord to be in touch with the hot grill plate. Always switch off the appliance before removing the mains plug. Before removing attachments or cleaning the appliance, allow it to cool completely. Take care! The hotplate will get very hot, and it stays hot for a long time after it has been switched off. Beware of burns! Do not touch any hot surfaces and take care when handling the appliance after use. Do not stand the bbq over the edge or corner of a table and avoid all contact with the bbq hot surfaces. Do not place the appliance on or near a hot gas electrical burner, or in a heated oven. Only use the appliance when it is placed on a stable and dry surface Do not leave the appliance unattended Always switch off and disconnect the appliance from power when it is not in use. This appliance is not meant for commercial use but exclusively for private use. Do not use the appliance without the grease cup and the bbq base all fitted properly together. Never cover the hotplate with aluminum foil or trays (this might damage the non-stick coating) Make sure without fail that this appliance is installed correctly before first use. Beware of fat oil or moisture spitting while grilling. Place the appliance on a surface that is resistant to heat. Keep the electric grill at least 30 cm from any walls when in operation Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons possibly resulting in depth or permanent disablement. For safety reasons do not use attachments that were not recommended or supplied by the manufacturer. Only trained personnel should repair electrical appliances. Unskilled repairs can cause

4 considerable danger to the user. If the power cord is damaged, it must be replaced only by the manufacturer, their after-sales service department or a similarly qualified person in order to avoid risks. No warranty for any possible damage can be accepted if the appliance is used for improper purpose, wrongly operated or unprofessionally repaired. In such a case, any warranty claim is void. Electric diagram Data plate

5 Description 1 Roasting hood 2 Hood handle 3 Hotplate 4 Grease cup 5 Base 6 Stand tube 7 Upper tube 8 Tool holder 9 Base tube 10 Condiment basket 11 Base handle 12 Opening for appliance socket 13 Detachable temperature Regulator with cable 14 Temperature indicator lamp 15 Power inlet socket 1 6 Feet 1 7 Axle 1 8 Wheel 1 9 Hubcaps 2 0 M4 6 screws 2 1 R Pins 2 2 M6 30 screws +M6 nuts 2 3 Bracket 2 4 M6 30 screws +M6 nuts 2 5 M6 30 screws +M6 nuts 2 6 Butterfly screw 2 7 M5x18 Screw

6 Installation instructions A. Fit the feet (16) to the base tube ( 9 ).Fix in place with two M4*6 screws(20). Left and right side are the same B.Put the axle (17) through the two holes In the base tube as shown. Attach the wheels (18) to the axle. C. Insert the R pin (21) through the holes in the ends of the axle to lock the wheels Press the hubcaps (19) onto the wheels. D.Insert the upper tube (7) to the base tube (9) Insert the M6 30 screws (22) from the outside through the holes in the two tubes. Then Tighten up with the nuts and washers provided.

7 E. Install the bracket (23) onto the upper tube (7) with M 6 30 screws(24)and nuts (24). Install the stand tube (6) onto the brackets(23). Note the slot on the stand tube which is going to fix the bbq base. Fix the stand tube in place with two screws (25)and nuts. F.Join the two parts (10A) and (10B) as shown. Hang to the outside of set screws (22) Place the tool holder (8) on the upper tube as shown G Set the bbq base (5) into the stand tube (6) By aligning the base with the slot and pushing the bbq all the way down. When removing the bbq base step softly on the base tube (9) hold the handles of the bbq base and lift it off H Put the grease cup (4) into the bracket provided for it in the back of the bbq base. Push the grease cup into the correct position in the middle of the bowl-shaped base. (Tip: The grease cup can be filled with a little water to Make it easier to clean). It s recommended to install a butterfly screw (26) to lock the base to the trolley.

8 I.Place the hotplate (3) in the bbq (5). Insert the power inlet socket (15) of the hotplate into the opening for the powercord with the hotplate tilted upwards,then lower the hotplate onto bbq base. Before taking the hotplate out, make sure it is cool and disconnected from the power. Attention : The hotplate must only be used TOGETHER with BBQ bowl! J.Use a M5 18 screw (27) through the inside of the hood with silicone washer and lid hook (26) into the hood handle Tighten the hood clockwise to fix the handle. While assembling, keep the hood handle and hook aligned K.Insert the temperature regulator with cable(13) into the power inlet socket. Plug in the appliance When inserting or removing the power cord hold the handle of the bbq base to avoid pushing over the appliance. Attention: Please take care. Avoid tripping over by the power cord when operating the appliance Arrange the power cord so its out of your way. Remember to remove the plug after use. L. The roasting hood can act as a wind shield by clipping the hook onto the hotplate

9 Before using the appliance for the first time Remove all the packaging materials and wash the hotplate (3), grease cup (4) and roasting hood (1) thoroughly Important: Dry all the different parts thoroughly. This applies especially to the power inlet socket (15).Never immerse the power cord with regulator (13) in water. Heat the grill to its maximum setting for about 3-5 minutes, with the roasting hood in place and without any food. Residues left from manufacturing may cause some smell and smoke when the appliance is used for the first time. Cooking instructions Connect the appliance to the mains electricity supply. Set the temperature regulator (13) to the required temperature level (it usually takes about 3 minutes to preheat). Pre heating is faster with the roasting hood in place. The temperature indicator lamp (14) will go out as soon as the required temperature has been reached. Place the food to be grilled on the hotplate (3) Cooking times The following are recommended cooking times. Different times will be required for different weights and sizes of foods to be grilled, and depending on whether you are grilling with or without the roasting hood. Weather conditions can also affect cooking times. Food to be grilled Temperature grade setting Cooking time Steak/beef mins Lamb mins Chicken drumsticks mins Chops mins Chicken wings mins Fillet of pork mins Whole fish mins Kebabs mins Various sausages mins Tips for grilling Your meat will be more if you marinade in the refrigerator it overnight before cooking (you can make your own marinade from oil (to aid moistness), vinegar, fruit juice or wine (to tenderise) and a mixture of seasonings for flavour). Always use tongs to turn grilled food (using a fork to turn the food will dry it out and damage the non-stick coating). Take care with tongs not to damage the non-stick coating. Only turn meat and fish once during grilling. You do not need to turn it more than once and too much turning dries food out.

10 Never cook meat for too long. Even pork is better if it is served when it is still a little pink and juicy. If cooked food sticks to the hotplate, rub the plate with a piece of kitchen paper soaked in oil from time to time. Cleaning and looking after the appliance Disconnect the appliance from the mains electricity supply. Allow the grill to cool completely. Take the power cord with regulator (13) out of the appliance socket. Clean the hotplate (3) and grease cup bowl (4) with warm washing-up water and a damp cloth. Do not use steel wool pads, br ush or abrasives to avoid any damages to the coating of hotplate. Wipe the base of the appliance (5) with a damp cloth. Fat splashes can be removed with a mild cleaning agent. Note: The hotplate has a non-stick coating. Do not scratch this coating during either the cooking or the cleaning stages. Tip: Protect the appliance from dust and dirt if it is not to be used for a prolonged length of time (dry thoroughly then wrap it in a plastic bag). Store it in a cool dry place. Disposal Disable unserviceable appliances immediately. Remove the mains plug and cut up the mains connection cable. If possible, bring unserviceable appliances to an official waste collection point. Many local authorities provide removal services for bulky refuse at least once a year. Please see separate sheet for warranty details For service and warranty repairs please contact your place of purchase, BRANCHES AUSTRALIA WIDE Call for your nearest store Barbeques Galore Limited, Build A2, Campus Business Park, Parramatta Road, Homebush, NSW CSR1@bbqgalore.com.au