FX1200 Food Processor

Transcription

1 FX1200 Food Processor First Use Safety Recommendation Please read through this booklet for safe and efficient use of the appliance. We urge you read and follow all instructions, even if you are familiar with a similar appliance. Keep this guide handy for future reference. English Page 02 Farsi Page 08 Arabic Page 14 FX1200

2 English Figure A

3 English Intended use Your Black & Decker Food Processor has been designed for processing ingredients as listed in this manual. This appliance is intended for indoor consumer use only. Safety Instructions Warning! When using mains-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material damage. Read all of this manual carefully before using the appliance. The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury. Retain this manual for future reference. Always route the cord carefully to avoid a tripping hazard. Never operate an appliance directly below the socket-outlet it is connected to. Using your appliance Make sure that the appliance is switched off before connecting to or disconnecting from the power supply. Always take care when using the appliance. Do not use the appliance outdoors. Never pull the power supply cord to disconnect the plug from the socket. Keep the power supply cord away from heat, oil and sharp edges. Disconnect the appliance from the power supply when not in use, before fitting or removing parts, maintenance and before cleaning. Surfaces may be hot during use and during the cool down period Do not operate or place any part of this appliance on or near any hot surface, such as a gas or electric burner or in a heated oven. When using an extension cord with your appliance, make sure the extension cord is correctly wired & rated for its use. Safety of others Do not allow children or any person unfamiliar with these instructions to use the appliance. Do not allow children or animals to come near the work area or to touch the appliance or power supply cord. Close supervision is necessary when the appliance is used near children. Never leave an appliance unattended when in use Do not allow the cord set to hang over bench tops After use Switch off and remove the plug from the socket before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance. When not in use, the appliance should be stored in a dry place. Children should not have access to stored appliances. Inspection and repairs Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation. Do not use the appliance if any part is damaged or defective. Have any damaged or defective parts repaired or replaced by an authorised repair agent. Before use, check the power supply cord for signs of damage, ageing and wear. Do not use the appliance if the power supply cord or mains plug is damaged or defective. If the power supply cord or mains plug is damaged or defective it must be repaired by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. Do not cut the power supply cord and do not attempt to repair it yourself. Never attempt to remove or replace any parts other than those specified in this manual. Do not attempt to repair the appliance. Take it to your nearest Black & Decker-owned or authorised Service Centre for repair. Double insulation This appliance is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. Additional safety instructions for Food Processors Do not immerse the appliance, cord set or plug in liquids Always leave sufficient space around the appliance for ventilation Keep loose clothing, hair, jewellery, etc. away from moving parts. Do not use the unit if you have wet hands or bare feet. Care is needed when handling cutting blades, especially when removing the blades from the bowl, emptying the bowl and during cleaning. Switch off the appliance before changing accessories or approaching parts which move in use. -3-

4 English Features This appliance includes some or all of the following features (fig. A). 1. Motor housing 2. Swivel head 3. On/Off switch & speed control 4. Pulse control 5. Swivel head release button 6. Blade storage 7. Foot 8. Bowl 9. Bowl lid 10. Lid seal 11. Bowl pusher 12. Upper chopping blade 13. Lower chopping blade 14. Dough blade 15. Whisk 16. Chopping blade spindle 17. Blade carrier 18. Thin slicing blade 19. Thick slicing blade 20. Thin shredding blade 21. Thick shredding blade 22. Parmesan blade 23. French fries blade small 24. French fries blade carrier 25. French fries blade large 26. Spatula 27. Jug 28. Lower jug blade 29. Upper jug blade 30. Jug lid 31. Jug lid cap 32. Jug seal 33. Juice extractor 34. Juice extractor lid 35. Juice extractor pusher -4- Assembly This appliance requires some assembly to complete the required task. Please refer to the relevant section for particular assembly details. All parts should be cleaned before use. See Cleaning for details. Use As a Food Processor Carefully fit the lower chopping blade (13) over the chopping blade spindle (16) then fit the upper chopping blade (12) onto the lower blade, rotating the blades in a clockwise direction so they lock together and onto the spindle. Note: The blades should be at right-angles to each other, forming an X-shape. Remove the bowl lid (9), fit the spindle & blades onto the metal pin in the centre of the bowl then re-fit the bowl lid, making sure the lid seal (10) is in place. Ingredients can be added to the bowl while the lid is off, or through the chute in the lid using the bowl pusher (11) provided. Fit the bowl pusher (11) into the inlet chute in the lid. This should be left in place during use to prevent spills. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Note: The swivel head cannot be raised if the speed selector (3) is in any position other than OFF. Place the assembled bowl in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. Rotate the speed control (3) to the desired speed until the ingredients are chopped as required then rotate the control back to 0 to turn the appliance off. The pulse button (4) can be used instead of the speed control. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the bowl lid then carefully remove the spindle & blades & transfer the ingredients to a suitable container. The blades can be removed from the spindle individually, rotating them in an anti-clockwise direction.

5 English As a Dough Mixer Fit the dough blade (14) over the chopping blade spindle (16), rotating the blade in a clockwise direction so it locks onto the spindle. Remove the bowl lid (9), fit the spindle & blades onto the metal pin in the centre of the bowl. Place the ingredients in the bowl, & re-fit the lid, making sure the lid seal (10) is in place. Liquid ingredients can be added to the bowl through the chute in the lid. Fit the bowl pusher (11) into the inlet chute in the lid. This should be left in place during use to prevent spills. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Note: The swivel head cannot be raised if the speed selector (3) is in any position other than OFF. Place the assembled bowl in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. Rotate the speed control (3) to the desired speed until the ingredients are mixed as required then rotate the control back to 0 to turn the appliance off. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the bowl lid, spindle & dough blade, & transfer the ingredients to a suitable container. The blades can be removed from the spindle by rotating it in an anti-clockwise direction. Note: Never use the whisk (15) to knead dough. Note: When preparing dough, do not operate the appliance for longer than 20 seconds. After 20 seconds use, wait at least 2 minutes before operating the appliance again. Processing Guide Ingredients Quantity Speed Setting Time (seconds) Meat 1,000g Max 10 to 20 Onions 700g 5 - Max 10 to 20 Nuts 600g Max 10 to 20 Fish 700g Pulse - Max 10 to 20 Cheese 700g Pulse Max 10 to 20 Carrots 700g Pulse Max 20 Apples 700g 5 Max 10 to 20 Mayonnaise 4 eggs / 1 litre oil 8 - Max Note: The maximum capacity of this appliance is 800g of dough (500g of flour and 300g of water). As a Whisk Fit the whisk (15) over the chopping blade spindle (16), rotating the whisk in a clockwise direction so it locks onto the spindle. Remove the bowl lid (9) then fit the spindle & blades onto the metal pin in the centre of the bowl. Place the ingredients in the bowl, & re-fit the lid, making sure the lid seal (10) is in place. Liquid ingredients can be added to the bowl through the chute in the lid. Fit the bowl pusher (11) into the inlet chute in the lid. This should be left in place during use to prevent spills. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Note: The swivel head cannot be raised if the speed selector (3) is in any position other than OFF. Place the assembled bowl in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. Rotate the speed control (3) to the desired speed until the ingredients are mixed as required then rotate the control back to 0 to turn the appliance off. The pulse button (4) can be used instead of the speed control. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the bowl lid, spindle & whisk, & transfer the ingredients to a suitable container. The whisk can be removed from the spindle by rotating it in an anti-clockwise direction.

6 English As a Slicer / Shredder Carefully fit the required blade (18, 19, 20, 21, 22 or 23) to the blade carrier (17) so that the cutting edges are in line with the smooth face of the blade carrier. Place the chopping blade spindle (16) onto the metal pin in the centre of the bowl then place the holder & blade over the hexagonal portion of the spindle. Re-fit the bowl lid, making sure the lid seal (10) is in place and place the bowl pusher (11) into the inlet chute in the bowl lid (9). The bowl pusher should be left in place during use to prevent spills. Place the assembled bowl in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. Rotate the speed control (3) to the desired speed. As a Blender Carefully fit the upper jug blade (29) over the lower jug blade (28) rotating the blades in a clockwise direction so they lock together. Note: The blades should be at right-angles to each other, forming an X-shape. Remove the jug lid (30) and fit the blades onto the metal pin in the centre of the bowl before replacing the lid, making sure the seal (32) is in place. Ingredients can be added to the jug while the lid is off, or by inserting them through the hole left when the jug lid cap (31) is removed. Whisking Guide Ingredients Quantity Speed Setting Eggs 4 1 Max Cake mix 800g 8 Max Cream 500g 8 - Max Remove the pusher from the inlet chute & add the ingredients through the inlet chute, using the pusher to gently press them onto the cutting blade. Note: Never insert fingers or allow loose clothing, jewellery, hair, etc. to enter into the inlet chute. Add ingredients until the bowl is full or sufficient ingredients have been processed then rotate the control back to 0 to turn the appliance off. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the lid then take the blade carrier & spindle from the bowl before transferring the ingredients to a suitable container. The blades can be removed from the carrier by carefully pushing it in the opposite direction of assembly. Note: The large French fry blade (25) has a unique carrier (23). This cannot be used for any other blade. The large French fry blade & carrier are used in the same way as the other carrier & blades. Slicing / Shredding Guide Ingredients Quantity Speed Setting Carrots 500g 1-3 Radish 500g 1 3 Squash 1,000g 1 3 Cucumber 1,000g 1 3 Cheese 500g 1 Max Potato 500g 1 3 Note: Never insert fingers or allow loose clothing, jewellery, hair, etc. to enter into the inlet. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Note: The swivel head cannot be raised if the speed selector (3) is in any position other than OFF. Place the assembled jug in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. -6-

7 English Rotate the speed control (3) to the desired speed until the ingredients are blended as required then rotate the control back to 0 to turn the appliance off. The pulse button (4) can be used instead of the speed control. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the jug lid then carefully remove the spindle & blades & transfer the ingredients to a suitable container. The blades can be removed from the spindle individually, rotating them in an anti-clockwise direction. As a Juice Extractor Place the juice extractor (33) over the metal pin in the centre of the jug (27) & fit the juice extractor lid (34), making sure the seal (32) is in place. Place the juice extractor pusher (35) into the inlet chute in the juice extractor lid (34). The pusher should be left in place during use to prevent spills. Place the assembled juicer in the recess in the motor housing (1). Rotate the swivel head back towards the motor housing & push it down until it latches in place. Connect the appliance to a suitable electrical supply. Rotate the speed control (3) to the Maximum speed. Remove the pusher from the inlet chute & add the ingredients through the inlet chute, using the pusher to gently press them into the juicer. Note: Never insert fingers or allow loose clothing, jewellery, hair, etc. to enter into the inlet chute. If ingredients jam in the juicer, use the pusher. Note: If it is not possible to clear a blockage using the pusher, switch off & disconnect the appliance from the electrical supply, then raise the swivel head & open the jug to clear the blockage manually. Add ingredients until the jug is full or sufficient ingredients have been processed then rotate the control back to 0 to turn the appliance off. Press the swivel head release button (5), guiding the swivel head (2) as it lifts. Lift the bowl from the appliance. Remove the lid & juicer before transferring the ingredients to a suitable container. Maintenance Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. -7- Warning! Before performing any maintenance or cleaning of the tool, disconnect the appliance from the power supply. Ventilation slots should be cleaned occasionally with a clean, dry paint brush. Cleaning The motor housing (1) should be cleaned with a clean damp cloth only. The stainless steel blades can be cleaned in a dishwasher. Alternatively, they can be washed in warm soapy water. Rinse with clean water and dry thoroughly with a dry soft cloth. All other parts should be washed in warm soapy water. Rinse with clean water and dry thoroughly with a dry soft cloth. Note: Do not use abrasives or chemical cleaners on any part of this appliance. Technical data FX1200 Voltage V Power input W 1,000 Cable length m 1.0 Container size l Processor Bowl 2.2lt Blender Bowl 1.5lt Weight kg 9.92Kg Protecting the environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose it off with other household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. A list of authorised Black & Decker repair agents and full details of our after-sales service and contact are available on the Internet at:

8 English BLACK & DECKER HOME APPLIANCE 2 YEAR WARRANTY Black & Decker provides a2yearwarranty for this product from the date of purchase against defects due to defective materials or workmanship. Motor/element burn-outs due to voltage fluctuations are not covered under warranty. If the product should become defective within the warranty period, Black & Decker will repair or (at Black & Decker's discretion) replace it free of charge. The warranty provisions do not cover failure due to accident, misuse, abuse, negligence or non observation of local regulations on the part of the user. Equally, the warranty provisions do not apply where the appliance has been serviced by a person not authorized by Black & Decker or serviced with non-approved parts and this has contributed to the fault of the product. Superseded models without a replacement equivalent will either be repaired or (at Black & Decker's discretion) replaced with another product of similar retail value. UPON PURCHASE Fill in the Warranty Registration Card with the original Authorized Dealer's stamp (indicating date of purchase) and attach your purchase receipt to it. Retain in case of claims in the future. MAKING A CLAIM Take your defective product together with the Warranty Registration Card & purchase receipt to your local service Centre. You can either do this in person or send it freight prepaid. If mailing or shipping your appliance, ensure that it is packed carefully in a sturdy carton with enough packing material to prevent damage. Include a note describing the problem to the service Centre and be sure to give your return address. DESIGNED FOR DOMESTIC PURPOSES ONLY.

9

10

11

12

13

14

15

16

17

18

19

20 Names & Addresses for Black & Decker Service Concessionaries Afghanistan: Ishan National Co., Opp. Ministry of Justice, Kabul. Tel.: Algeria: SARL Outillage Corporation, 04 Route De Dely Brahim Cheraga, Alger. Tel.: /508, Fax: Bahrain: Fawaz Al Zayani, P.O.Box 26563, Adliya, Manama. Tel.: /712756, Fax: Bangladesh: Ultra Corporation, 8, Kushol Centre, Uttara, Dhaka Tel.: /9756 Ext.28, Fax: Egypt: Anasia Egypt for Trading S. A. E., P.O.Box 2443, 110 Mostafa Refaat Street, Sheraton Heliopolis 11361, Cairo. Tel.: , Fax: Ethiopia: Tewfik Sherif & Co. Ltd., P.O.Box 5583, Debre Zeit Road, Addis Ababa. Tel.: /601, Fax: India: Gryphon Impex Pvt. Ltd., D-6/4, Okhla Industrial Area, Phase-I, New Delhi Tel.: , Fax: Iran: Tehran - Service Centre of Iran, No 510, South Karger Ave, Below Pasteur Sq. Tehran. Tel.: /0656/ Kish Island: Cayhan Electric Co., No. 69, Paradise Shopping Centre, Kish Island. Tel.: Jordan: Bashiti Hardware, P.O.Box 1564, TLA Ali, Amman. Tel.: / , Fax: / Kenya: Zylog Enterprises, IPS Building, Kuanda Street, P.O.Box 40877, Nairobi. Tel.: /199, Fax: Kuwait: Al Omar Technical Co., P.O.Box 4062, Safat, Kuwait. Tel.: /0039, Fax: Lebanon: Est. F.A. Kettaneh SA, P.O.Box , Dora Highway, Kettaneh Building, Beirut. Tel.: /6, Fax: Libya: El Ghoul Brothers, P.O.Box 348, Islamic Call Bldg., Office , Benghazi. Tel.: /4183, Fax: Madagascar: Group Tana Confort S. A. R. L., B. P. 1770, Antananarivo. Tel.: , Fax: Malta: John G. Cassar Ltd., 36 Victory Str, Qormi QRM 06, Malta. Tel.: , Fax: Mauritius: Happy World Marketing Ltd., Block 2, Industrial Estate, Coromandel, P.O.Box 429, Port Louis. Tel.: , Fax: /7400. Nepal: Universal Trading Centre, P.O.Box 1947, Tripureswor, Kathmandu. Tel.: /260587/785, Fax: Nigeria: Amin Bros. Eng. Co. Ltd., 30A (Plot 1291), Akin Adesola Street, Victoria Island, Lagos. Tel.: , Fax: Oman: Oman Mktg. & Service Co., P.O.Box 2734, Ruwi, Muscat. Tel.: , Fax: Pakistan: Karachi - Ammar Service & Spares, 60, Bank Arcade, Serai Road, Karachi. Tel.: , Fax: /5243. Pakistan: Lahore - Electronics Inn, 212-G Raja Centre, Main Market, Gulberg, Lahore. Tel.: Philippines: Modern House International Enterprises, 213 Rizal Ave. Extension, between 2nd and 3rd Ave. Kalookan City. Tel.: , Fax: Qatar: Al Muftah Trading & Cont., P.O.Box 875, Doha. Tel.: / , Fax: Saudi Arabia: Dammam - Ebrahim Fawaz Al Zayani, P.O.Box 76026, Al Raka, Dammam. Tel.: , Fax: Jeddah: Anasia - P.O.Box 50959, Jeddah Tel.: , Fax: EAC (Al Yousuf) - P.O. Box 30377, Jeddah Tel.: , Fax: Madina: Garziz Trdg. for Bldg. Mat.&Decor., P.O.Box 3364, Madina. Tel.: / , Fax: Riyadh: Anasia, P.O.Box 18689, Riyadh Tel.: , Fax: Yanbu: Bin Afif, P.O.Box 530 Yanbu, Al Bahr. Tel.: /8867, Fax: Sri Lanka: Delmege Gen. Equip. Pvt. Ltd., No. 428/1AT. B., Jaya Mawatha (Darley Road), Colombo-10. Tel.: , Fax: Sudan: United Distribution Company, P.O.Box 325, Sayed Abdul Rehman Street, Khartoum. Tel.: /777296, Fax: Tanzania: General Motors Investment, P. O Box 16541, 14 Vingunguti Nyerere Road, Dar Es Salaam. Tel.: /5022, Fax: /5412/3. Tunisia: STE Tunisienne De Quincaillerie Stq., Nvelle Z.I 2013, Ben Arous, Tunis, Tunisia, Tel: , Fax: UAE: Abu Dhabi - Light House Electric., P.O.Box 120, Abu Dhabi. Tel.: , Fax: Dubai - Black & Decker (O) A.G., P.O.Box 5420, Dubai. Tel.: /233, Fax: Ideal Mach. & Equipt. R. W/shop P.O.Box 37116, Al Quoz, Dubai. Tel.: , Fax: Sharjah - McCoy Middle East LLC, P.O.Box 20228, Sharjah. Tel.: , Fax: Uganda: The Building Centre, Kitgum House, 52 Station Road, P.O.Box 7436, Kampala. Tel.: , Fax: Yemen: Aden - Middle East Trad. Co. Ltd., Mulla Dakka, Aden. Tel.: , Fax: Sana'a: Middle East Trad. Co. Ltd., P.O.Box 12363, Hayel Street, Sana'a. Tel.: , Fax: Taiz: Middle East Trad. Co. Ltd., Campa area near Al-Kair mosque, Taiz. Tel.: /232033, Fax: Zimbabwe: J.D.Distributors, P.O.Box 226, 17 Bessemer Road, Graniteside, Harare. Tel.: , Fax: Cyprus: G. Kyprianou Trading Co Ltd., 51 Prodromou AVE. Strovolos, 1681, P.O. Box Nicosia Cyprus. Tel.: /1, Fax: , gktltd@spidernet.com.cy WARRANTY REGISTRATION CARD