WINE AND BAR SERIES. Sink Installation Kit. For assistance, call ; for UK ; at

Size: px

Start display at page:

Download "WINE AND BAR SERIES. Sink Installation Kit. For assistance, call ; for UK ; at"

Milo Ethelbert Reeves
5 years ago
Views:

1 WINE AND BAR SERIES Sink Installation Kit For assistance, call ; for UK ; at

2 Unpacking Begin by placing the package on a protected flat surface. Remove all cardboard, foam packaging material and clear plastic bags. Dispose / recycle all packaging materials. Verify all the contents in the box and gather the required tools. See Parts Supplied and Tools Needed in the following sections Installation Requirements Pressure of supply water: 0.05MPa - 1.0MPA, if greater than 1.0MPa please install pressure reducing valve. Temperature of supply water must be less than 90c Parts Supplied Sink Install Kit Sink 1 Faucet Assembly 1 Top Washer with Sealing Gasket 1 2 Sealing Gasket 1 2 Metal Washer 1 Threaded Reducer 1 Plastic Fastening Sleeve 1 Tipout Tray 1 Tipout Hinge Set (Left and Right) 1 Handle Bolts (M5 x 16mm) 2 Tipout Hinge Screws (M x mm) 12 2mm Spacers 2 Drain Body 1 4-1/4 Rubber Washer 1 Anti-Friction Ring 1 Drain Locking Nut 1 Plastic Tailpiece Washer 1 Tailpiece 1 Tailpiece Locking Nut 1 Removable Strainer 1 Hot(Red) / Cold(Blue) Braided Hoses 1of Each Color Braided Hose Plastic Fastening Sleeve Threaded Reducer 2.0mm Spacer Sink Top Washer with Sealing Gasket M3 X 14MM Screws Sealing Gasket Faucet Assembly Metal Washer M4 X 16MM Handle Bolt Anti-Friction Ring Drain Locking Nut Drain Body Plastic Tailpiece Washer Tip-out Tray Tip-out Hinge Removable Strainer 4-1/4 Rubber Washer Tailpiece Locking Nut Tailpiece

3 Manufacturer One Year Warranty When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of one year from the date of purchase. NEWAGE PRODUCTS INC. WILL NOT PAY FOR: 1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them. 2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, fire, flood, improper installation, acts of God, neglect, corrosion, modification, mishandling or not following care instructions. 3. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial environment, or handled in anyway inconsistent with the installation instructions included with the product. 4. Surfaces damaged due to chemical interaction resulting in corrosion of metal. 5. Replacement parts for NewAge products outside Canada and the United States, U.K. 6. Loss of product contents due to theft, fire, flood, accident or acts of God. 7. Shipping or freight fees to deliver replacement products or to return defective products. 8. Any labor costs during the limited warranty period. DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE Tools Needed 1 x #2 Phillips Head Screwdriver x Pencil 1 x Set Square 1 x Tape Measure 1 x #2 Phillips Bit 1 x Plumbers Putty 1 x Silicone 1 x Caulking Gun 1 x Jig Saw 1 x Cordless 1 x Wood Bit 1 x 1-3/8 Power Drill Hole Saw

4 Removing Drawer 1 Extend drawer fully. 2 Press plastic triggers on underside of drawer according to arrows in image. 3 Tilt and remove drawer. 4 Unfasten and remove both the drawer face and the handle. Preparing Cabinet for Sink Installation 1 Unfasten and remove left and right drawer slides. 2 Measure and mark opening to be cut in cabinet top with a pencil. 5-5/8 12-3/ /4

5 3 4 Drill a 1/2 hole in each corner of the marked opening. Connect all four corner holes using a jigsaw by cutting along the marked lines. Fasten tip-out hinges to cabinet using four M3 x 14mm screws for each hinge /16 from Front Use 2.0mm spacers and align the drawer edges with the edges of the doors. Bottom Flush with Crossbar Align Edges Reaching through the top of the cabinet attach drawer face to tip-out hinges using two M3 x 14mm screws per hinge. 7 8 Install tip-out tray and handle.

6 10 Preparing Countertop for Sink Installation 1 Measure and mark opening to be cut in countertop with a pencil. +24 for each additional cabinet 10-3/4 5-5/8 12-3/4 Drill a 1/2 hole in each corner of the marked opening. 2 3 Connect all four corner holes using a jigsaw by cutting along the marked lines. 4 Place worktop over cabinets and lower onto cabinets. 4 - #8 x 25mm screws

7 Drill 4, 3/32 pilot holes on interior roof of cabinet Tighten screws to secure cabinets.

8 Installing the Sink and Faucet 1 Insert sink into opening and trace faucet hole. 2 Remove sink and use 1-3/8 circular saw to cut faucet hole. Apply a thin bead of plumber s putty to the perimeter of the drain opening on the inside of the sink. 3 4 Insert the drain body into drain opening and press into plumber s putty. From the bottom of the sink add the rubber washer, anti-friction ring and tighten the drain locking nut 5 6 From the bottom of the sink add the tailpiece washer, tailpiece and tighten with the tailpiece locking nut. Drain Locking Nut Anti-Friction Ring Rubber Washer Tailpiece Locking Nut Tailpiece Tailpiece Washer

9 Apply silicone to bottom edge of sink using a caulking gun. 7 8 Insert sink into opening and ensure front edges of sink and countertop are parallel. PARALLEL 9 10 Apply a small bead of silicone to the perimeter of the sink. Attach the braided hoses to the faucet assembly Attach threaded reducer to the faucet assembly. Add top washer with sealing gasket to assembly and insert braided hoses into faucet hole.

10 From the inside of the cabinet add the sealing gasket, metal washer and tighten the plastic fastening sleeve Fasten the (red) hot water braided hose to the hot water intake angle valve, and the (blue) cold water braided hose to the cold water intake angle valve. Water Intake Angle Valve 15 Attach the sink drain tailpiece to the drain pipe outlet. Sealing Gasket Metal Washer Plastic Fastening Sleeve For assistance connecting sink to plumbing system please contact your local contractor or plumber. 16 Turn on water and check for leaks around drain opening. 17 Use plumbers putty to stop any water leaks around drain opening.

DELEVINGNE WIDESPREAD FAUCET INSTALLATION

DELEVINGNE WIDESPREAD FAUCET INSTALLATION SKU(s): 927254 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing,