G16 Luxury Collection. Twin Bowls Kitchen Sink. Drop-in. Owner s Manual. Undermount

Transcription

1 G16 Luxury Collection Drop-in Undermount Owner s Manual Twin Bowls Kitchen Sink

2 Tools Required: Ruler/Tape Measure Pencil Masking Tape Safety Glasses Kitchen Silicone Sealant Screwdriver Drill Jigsaw & Suitable Blade (if work top cutout is required) OR Invert sink and position onto the work top. Locate sink front to rear and right to left so the bowl will not interfere with the cabinets below. Trace a pencil line around the outside edge of the sink and remove the sink from the worktop. Measure in 7 mm from the initial sink outline and draw a second line inside the first. 2 Drill starter hole inside of cutout line. Option A Sink Drop-In Installation Instructions 1 Locate the drop-in sink template inside the box. Carefully cut along the outline and discard the inner section of the template. Place the paper template onto the upper surface of your work top and position it carefully where you want the sink to fit. When positioning the template take note of cabinet panels and rails below as well as ensuring there will be enough access for faucet connections. Fix the template in place with masking tape and carefully draw around the inside of the template with a pencil. Remove the inner template. 3 Using a Jigsaw, cut inside of cutout line. Trial fit sink to check proper fit. Cut Inside of Line Masking Tape

3 4 Install both strainers. Insert the metal strainer with the rubber seal into the drain hole. Position the plastic bowl end the rubber gasket underneath the drain hole. Using a screw, tighten the plastice bowl to the metal strainer. 7 Fix the clips. Rail Countertop 1. Basket 2. Metal Strainer 3. Screw 4. Rubber seal 5. Rubber gasket Clip Screwdriver Sink 6. Main body 6 8 Seal the sink with silicone. Note: plumbers putty is not required. If plumbers putty is used, it replaces the rubber seal 5 Verify that the sink fits perfectly. The lip of the sink should be resting on the countertop. 9 Install faucet. Then make proper water and waste pipe connections. 6 Insert clips in rails. Bottom View of Sink Bottom View of Sink

4 Option B Sink Undermount Installation Instructions 3 Using a Jigsaw, cut inside of cutout line. Trial fit sink to check proper fit. Cut Inside of Line 1 Locate the undermount template inside the box. Carefully cut along the outline and discard the inner section of the template. Place the paper template onto the upper surface of your work top and position it carefully where you want the sink to fit. When positioning the template take note of cabinet panels and rails below as well as ensuring there will be enough access for faucet connections. Fix the template in place with masking tape and carefully draw around the inside of the template with a pencil. Remove and discard the template. 4 Build a support frame. 495 mm 770 mm Rail Frontal view Rail Masking Tape Frame Sink Frame 2 Drill starter hole inside of cutout line. Verify the fit of the sink and the counter top.

5 5 Install both strainers. Insert the metal strainer with the rubber seal into the drain hole. Position the plastic bowl end the rubber gasket underneath the drain hole. Using a screw, tighten the plastice bowl to the metal strainer. 7 Apply silicone sealant on the border of the sink and install the countertop. Then remove exceeding sealant. 1. Basket 2. Metal Strainer 3. Screw 4. Rubber seal 5. Rubber gasket 6. Main body Install faucet. Then make proper water and waste pipe connections Note: plumbers putty is not required. If plumbers putty is used, it replaces the rubber seal 6 Insert sink on the support frame. Apply silicone sealant to each corner between the frame and sink.

6 CARE Clean your sink regularly using warm soapy water. Always rinse the sink after using any cleaning agent. The surface may be wiped with a clean soft cloth to remove water spotting. Do not cut, chop or dice food directly of the surface of the sink. Do not let staining objects in direct contact with the sink for long period of time. Do not use abrasive cleaners, scouring pads, or steel wool. WARRANTY Artika For Living Inc. is proud to offer you a one (1) year warranty. We warrant it to be free of manufacturing defects in material and workmanship for a period of one (1) year from the date of purchase. Should a defect arise within the Warranty period, Artika For Living Inc. will provide a replacement free of charge. Please call for details. Our warranty does not cover a sink that has been installed incorrectly, or subjected to abnormal use. Our Stainless Steel Sink is intended for residential use only, and not commercial use. The Warranty does not cover shipping costs, labor costs or any other cost associated with the installation or replacement of the sink, and is extended to the original consumer. Artika For Living Inc. is not liable for indirect or consequential damages arising from improper use or installation of this sink. QUE STIONS? Costumerservice@artikaworld.com Atlantis Sink is a trademark of Artika