BCR130/5 BG BCR130/5 MG BCR164/6,5 BCR300/12

Transcription

1 DIAMOND CORE RIGS BCR130/5 BG BCR130/5 MG BCR164/6,5 BCR300/12 OPERATING MANUAL

2 CONTENTS General Power Tool Safety Warnings For your safety Tool Specifications Operating Controls Safety guidelines Intended Use Before Use Initial Operation Hand held drilling Hand held wet drilling Hand held dry drilling Drilling with a drill stand Drill stand fixation Secure using assembly Vacuum pump fixation Over head drilling Mounting the water collecting ring.13 Transport and Storage Maintenance and Cleaning Troubleshooting Replacement parts Guarantee Environmental Protection Noise/Vibration Information Declaration of Conformity BCR130/5 BG BCR130/164 Compact 8-66 mm BCR130/5 MG mm BCR164/6,5 BCR300/ mm Large BCR300/12 II mm

3 BCR130/5 BG BCR130/5 MG Compact Compact III

4 BCR164/6, Compact BCR130/5-164/6,5 BCR300/12 34 IV

5 BCR300/ Large Large Vacuum pump V

6 GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term power tool in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f ) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f ) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 6 BEAST CORE RIG OPERATING MANUAL

7 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. FOR YOUR SAFETY Working safely with this machine is possible only when the operating and safety information are read completely and the instructions contained therein are strictly followed. Before using for the first time, ask for a practical demonstration. Before working on the machine itself, pull the mains plug. Be careful of hidden electrical lines or gas and water pipes. Check the working area, e. g., with a metal detector. Wear safety goggles and hearing protection. Before commencing work, the GFCI protective switch must be checked for proper functioning. Before commencing work consult the responsible structural engineers, architects or site supervision about any planned borings, especially when cutting through reinforcing steel. The machine may only be operated using a power supply with protection earthing according to the regulations. The machine may not be operated by persons under the age of 16 years. The drill stand must always be mounted firmly and must not be able to move during drilling. Only mount the drill stand on an even, firm and smooth surface using the vacuum pump. When carrying out over head wet cut core drilling, a water collecting ring and water suction are always to be used. These must be in perfect condition. When drilling over head always secure the drill stand with the assembly. Prevent the drilling core from falling. BEAST CORE RIG OPERATING MANUAL 7

8 Vacuum pump Avoid any constrictions in the suction hose, e.g. due to dirt accumulation, squeezing, bending or stretching. Check the suction hose each time before use. Renew any leaking or damaged parts. Keep the cooling air vents on the pump free and clean. The underlying surface of the drill stand must be clean, firm, smooth, dry and without any holes. For further safety regulations, see the operating instructions for the drill stand. Caution: The machine automatically switches on immediately after inserting the plug in the mains and becomes hot after a long period of use. Always connect the core drill and the vacuum pump to the same power outlet. Do not carry out any changes or modifications to the machine. Should the machine have an operational fault, the vacuum function will remain for a short time. The cohesion is depe dent upon the underlying surface and seal retention. Stop working immediately and remove the drill stand completely. Use only original BEAST/B+BTec parts and accessories. TOOL SPECIFICATIONS Drill BCR130/5 BG BCR130/5 MG BCR164/6,5 BCR300/12 Input power (Watt) W W W W Motor (Voltage) 110 V 110 V 110 V 110 V (Frequency/Amps) Hz/16 A Hz/16 A Hz/16 A Hz/20A No-load speed min Bore diameter Wet/Dry 1. Gear Ø mm / / / /- Wet/Dry 2. Gear Ø mm 25-60/ / / /- Wet/Dry 3. Gear Ø mm 8-35/ / / /- Dimensions L x B x H cm 44,5 x 28 x 11,5 44,5 x 30 x 11,5 59 x 20 x x 27 x 22 Weight Motor 7,5 kg* 7,5 kg* 12,9 kg** 12 kg Guide block 4,1 kg 4,1 kg - 3,9 kg Drill Stand Compact 10,3 kg 10,3 kg 10,3 kg - Drill Stand Large 13,9 kg 13,9 kg 13,9 kg 13,9 kg Safety class (EN-IEC 61029) / I / I / I / I Safety class (IP Code) IP54 IP54 IP54 IP54 * Drill BCR 130 overall weight. ** Incl. guide block. Vacuum pump Rated voltage 110 Volt Maximum vacuum -800 mbar Rated input 500 Watt Weight 11,2 kg 8 BEAST CORE RIG OPERATING MANUAL

9 OPERATING CONTROLS 1 LED motor load 2 On/Off switch 3 Waterflow Indicator 4 GFCI protective switch 5 Grip 6 Hex collet 7 Water tap 8 Speed selection switch 9 Ventilation slots 10 Dry Drilling Kit 11 2nd Back Grip 12 Safety screw 13 Feed lever 14 Stand Grip 15 Rod with scale for drill angle adjustment 16 Locking screw 17 Clamping lever for Guide block for BCR Limit stop plate 20 Base plate 21 Adjusting screws 22 Safety bolt 23 Centering plate 24 Spindle nut 25 Screw assembly 26 Vacuumblock fastening screw 27 Connection for vacuum pump 28 Ventilating tap 29 Seal 30 Transportation wheels 31 Drill bit 32 Rubber cover 33 Fastening screw for water collecting ring 34 Water collecting ring 35 Clamping lever for Quick Release Guide 36 Safety bolt Quick Release Guide 37 Pressure gauge vacuum kit 38 Air vent 39 Filter cap 40 Vacuum gauge 41 Hose clip 42 Suction hose 43 Quick coupling 44 Fluid collecting container with float 45 Mains plug 46 Frame 47 Overload safety switch *Not all of the accessories illustrated or described are included as standard delivery. SAFETY GUIDELINES The definitions below describe the level of severity for each warning. Please read the operating manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. NOTE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage. INTENDED USE The machine is intended for drilling into concrete and reinforced concrete, when being used in conjunction with diamond core bits for wet drilling and a suitable water supply. BCR130/5 can also be used for dry drilling in masonry and other building materials with the dry drilling kit. The vacuum pump is intended for the fixation of drillstands Compact and Large. The pump is only designed for sucking in air, and no other gases or fluids. For damage caused by usage other then intended, the user is responsible. BEFORE USE When drilling through walls or floors, make absolutely sure that there are no obstacles in the adjoining rooms and cordon off the building site. Prevent the drilling core from falling. BEAST CORE RIG OPERATING MANUAL 9

10 Always use the correct supply voltage: The power supply voltage must match the information quoted on the tool identification plate. INITIAL OPERATION Functional test for the GFCI protective switch 4 WARNING: The ON/OFF switch 2 must be switched off, in order to avoid unintentional starting of the machine when carrying out the functional test of the GFCI protective switch 4. Before commencing work, check that the GFCI protective switch is functioning properly: Press the «ON» button on the GFCI protective switch. The red control lamp indicates when the protective switch is ready for operation. Press the «TEST» button. The control lamp must go off. Setting the speed range CAUTION: Actuate the gear selector switch only when the machine is at a standstill. The gear selector switch allows for pre-selection of three speed ranges. Position : low speed Position : medium speed Position : high speed Switching On/Off Switching on: Press the ON/OFF switch 2 (position 1 ). Switching off: Press the ON/OFF switch 2 (position 0 ). WARNING: Use BCR130/5 only in combination with a drillstand when drilling in first gear, Position 1 (low speed). Overload Protection The LED 1 indicates the motor load, whereby the following conditions are distinguished: Blue: No load Green: Regular drilling load Red: Overload Excessive overloading will shut down the motor. After the motor has cooled off, the motor can be switch on again with the Overload Safety Switch 47. Connecting the water feed Close the water tap 7. Connect the water feed hose to the water tap or the water pressure tank. When using the water pressure tank, make sure that there is sufficient pressure when working. Check the waterflow indicator 3. Mounting the drill bit 31 Clean and grease the thread on the drill bit 31 and the tool holding fixture 6. Screw a core bit 31 onto the tool holder 6 and tighten. Removing the drilling core Break off the drilling core and remove. HAND HELD DRILLING WARNING: Hand held drilling only for BCR130/5. Maximum bit diameters: Wet drilling in concrete: Ø 40 mm. Dry drilling in masonry: Ø 164 mm. Hand held wet drilling For wet drilling open the water valve 7 and switch on the machine 2. Hold the machine as rigidly as possible. Always use the grip 5 at the front of the machine. Start drilling by keeping the machine at a slight angle. After the bit is guiding itself into the material, swivel back the machine into the right angle position. 10 BEAST CORE RIG OPERATING MANUAL

11 Hand held dry drilling Mounting the dry drilling kit 10 DRILLING WITH A DRILL STAND Guide block setting A B A B Loosen the frontgrip 5 of the core drilling machine. Mount part A of the dry drilling kit onto the drill spindle 6. Slide the dry drilling sleeve (B) on part A in the desired position for the vacuum cleaner. Tighten the grip 5. Mount the hose of a industrial vacuum cleaner on the sleeve (B). Mount a core drill 31 onto the drill spindle 6. Using the dry drilling kit 10 Drilling is only possible if the masonry is absolutley dry. Use a powerful industrial dust exhauster. Change the filter regularly, there is risk of obstruction. Hold the machine as rigidly as possible. Always use the grip 5 at the front of the machine. Start drilling by keeping the machine at a slight angle. After the bit is guiding itself into the material, swivel back the machine into the right angle position. WARNING: The machine has a very high torque, especially in the first gear. Therefor drill only extremely concentrated, especially when working in first gear and with diameters of more than 60 mm. In case of sudden blocking of the core bit the machine, despite the safety clutch, might get out of control and hurt you considerably. When using a drill stand a right setting of the guide block is required. Guide blocks for BCR core drilling machines features slide strips for fine tuning on the drill stand. Loosen the safety nuts (A) using the supplied wrench 13. Adjust the bolts (B) for an flexible sliding of the guide block on the drill stand. Secure then the bolts with the safety nuts (A). Using Quick Release Guide BCR300/12 You can easy release the core drilling machine BCR300/12 from its Quick Release Guide and so from the drill stand. Loosen the guide block safety bolt 36 with the feed lever 13. Pull the machine safety lock. Slide the core drilling machine gently from the guide block. When replacing the machine secure accordingly. Aligning the drill stand Set up the drill stand at the drilling location. Pull the safety bolt 22 and rotate the centering plate 23 forwards, until it snaps in. Align the drill stand in such a manner that for the used machine the tip of the centering BEAST CORE RIG OPERATING MANUAL 11

12 plate is located directly above the required drilling location. Fasten the drill stand. Setting the drilling angle Loosen the clamping lever 17. Push in or pull out the rod 15 until the desired drilling angle is shown on the scale. Tighten the clamping lever 17. Drilling Always ensure a adequate anchorage in the underground. Open the water tap 7. Actuate the ON/OFF switch 2. Drill using an even forward feed. Do not overload the machine. The leaking water should be milky and not clear. Always loosen the locking screw 16 (BCR 130/5-164/6,5) or the clamping lever 35 (BCR 300/12) when drilling. After drilling switch the machine off and shut off the water tap. DRILL STAND FIXATION CAUTION: The drill stand must always be mounted firmly and must not be able to move during drilling. Secure using assembly Drill the rawlplug hole Ø 15/16 mm (see instruction rawlplug). Insert rawlplug. SD M12 Screw in assembly 25. Align the drill stand. Fasten the drill stand with the spindle nut 24. Vacuum pump fixation Setting up the vacuum pump Position the machine horizontally. Maximum tilt of 10. Fasten, mount suction hose 42 and fasten with hose clip 41. WARNING: Maximum drilling diameter of 100 mm. Mount the drill stand on an even, firm and smooth surface using the vacuum pump, never over head. Always connect the core drill and the vacuum pump to the same power outlet. Never turn off the vacuum pump during operation. Install the vacuum kit. Turn the fixation screws 21 ensuring, however, that the seal 29 is not squeezed. Align the drill stand. Mount the suction hose to the connection for the vacuum pump 27. Close the ventilating tap 28. Connect quick coupling 43 to vacuum kit 27 on the drill stand. The machine has no On/Off switch; it is put into operation by inserting the mains plug 45 into the socket. The existing vacuum can be read from the vacuum gauge 40. The vacuum gauge 40 must show a vacuum of below bar. If not check for leakage. Do not commence work until the required vacuum has been reached. Watch the vacuum gauge 40 while working. If the vacuum rises above bar, interrupt the work immediately and completely remove the drill stand. Empty the fluid collecting container 44 If fluid is sucked in during operation, the vacuum will no longer be maintained. Pull the mains plug out immediately. Unscrew the fluid collecting container 44. Remove the float and empty the container. Replace the float and screw on the container tightly again. CAUTION: The machine becomes hot after a long period of use. Do not touch the machine directly after operating it. 12 BEAST CORE RIG OPERATING MANUAL

13 OVER HEAD DRILLING DANGER: When drilling over head always secure the drill stand with the assembly. DANGER: When drilling over head, always use a water collecting ring and a industrial wet-type vacuum cleaner! Mounting the water collecting ring 34 Loosen the fixation screw 33 on the water collecting ring 34. Push the water collecting ring 34 onto the drill stand and press it firmly against the material to be drilled. Tighten fixation screw 33. Connect a industrial wet-type vacuum cleaner. When using the water collecting ring, attach a protective cover 32 onto it and drill through. Remove te drilled part of the cover 32 from the core bit. TRANSPORT AND STORAGE MAINTENANCE AND CLEANING Clean the machine with water and a brush after use and lubricate the moveable parts as well as the rack with a silikon spray. Always keep the machine and cooling air vents free and clean. It must always be kept in a dry, frost-free place. Clean the filter of the vacuum pump The condition of the filter must be checked at regular intervals. Loosen the four screws with hexagonal recess on the bottom of the frame 46. Unscrew filter cover 39. If necessary, renew filter parts. Screw on filter cap 39 again. The arrows on the cap must point in the direction of flow of the sucked in air. Mount the pump on the frame 46 again. TROUBLESHOOTING For malfunctions that are not specified in this chapter, when in doubt or when explicitly indicated, seek assistance from an authorized service facility. CAUTION: Danger of injury and damage! Pay attention to the weight of the appliance when transporting it. Clean the machine and remove the drilling dirt. Transport the machine and core bit separately. Blow out remaining water from hose and machine when it freezes. This appliance may only be stored inside a building. BEAST CORE RIG OPERATING MANUAL 13

14 Problem Possible cause Possible solution The motor doesn t work. Defective motor. Defective cable of plug. Defective switch. Contact customer service. Never repair the motor yourself. Danger! GFCI protective switch is not switched on, test! Have inspected by a electrical specialist and replaced if necessary. Contact customer service. Motor makes too much noise. Damaged windings. The carbon brushes of the Have the motor inspected by customer service. machine are worn. Motor mildly overheats. Motor overload. Motor doesn t cool sufficiently Prevent motor overload when drilling. Remove the dust from the motor, so that the cool air can flow. Motor runs. Core bit doesn t rotate. Rate of drilling progress decreases. Motor cuts out. Water leakage at the water swivel or gear housing. Gearing defective. Core bit segments polished. Water pressure/water flow rate too high. The core is stuck in the core bit. Maximum drilling depth reached. Core bit defective. Gearing defective. The clutch is releasing prematurely or slipping. The core bit has been jammed for too long. Electric power failure. Electronics defective. Shaft seal defective. Water pressure is too high. Have the machine inspected by the service facility. Sharpen the core bit on a sharpening plate while water is flowing. Use the feed lever to reduce the water flow rate. Remove the core. Remove the core and use a core bit extension. Check the core bit for damage and replace if necessary. Have the machine repaired at a service center. Have the machine repaired at a service center. Free the core bit. Switch the motor off and then on again. Check the plug connections, electric power supply and GFCI protective switch. Have the machine repaired at a service center. Have the machine repaired at a service center. Reduce the water pressure. 14 BEAST CORE RIG OPERATING MANUAL

15 REPLACEMENT PARTS If in spite of meticulous manufacturing and testing processes the device breaks down, have it serviced by a BEAST/B+BTec Service. GUARANTEE For this BEAST/B+BTec appliance we grant a warranty in accordance with the statutory/countryspecific provisions as from date of purchase (by evidence of invoice or delivery note). Damage that has occurred will be corrected either by replacement or by repair. Damage caused by improper handling is excluded from the warranty. Claims can be recognized only if the appliance is presented in a not-disassembled manner to a BEAST/B+BTec branch office, your BEAST/B+BTec field service employee or a customer service office for power tools authorized by BEAST/B+BTec. ENVIRONMENTAL PROTECTION Do not dispose of the appliance with domestic waste. Dispose of the appliance only via an authorized waste management company or your municipal waste management organisation. Adhere also to the applicable regulations. In case of doubt refer to your waste management organisation. Recycle all packaging material in an environmentally friendly manner. NOISE/VIBRATION INFORMATION Typically the A-weighted noise levels of the products are: Sound pressure level NEN-ISO Sound power level EN-ISO /5 93 db (A) 103 db (A) 164/6,5 89 db (A) 98 db (A) 300/12 90 db (A) 101 db (A) Vac. pump 70 db (A) 75 db (A) The typical hand-arm vibration is below 2,5 m/s 2 (EN-ISO 5349). Wear ear protection! C DECLARATION OF CONFORMITY We hereby declare that the appliance complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the device is modified without our prior approval. BCR130/5 BG/MG: EN , EN , EN- IEC , EN-IEC , EN-ISO , EN-IEC , EN-ISO 11204, EN 12348, EN-ISO 3744, EN-ISO , EN-IEC BCR164/6,5: EN , EN , EN-IEC , EN-IEC , EN-ISO , EN- IEC , EN-ISO 11204, EN 12348, EN-ISO 3744, EN-ISO , EN-IEC BCR300/12: EN , EN , EN-IEC , EN-IEC , EN-ISO , EN- IEC , EN-ISO 11204, EN 12348, EN-ISO 3744, EN-ISO , EN-IEC Vacuum pump: EN , EN , EN-IEC , EN-IEC , EN-ISO 11204, EN , EN-ISO 3744 Conforms to the following standards or normative documents 2006/42/EG, 2014/30/EU. Subject to change without notice. Zevenbergen, August 2016 R.G.W. van den Boogaart General manager B+BTec Munterij AH Zevenbergen P.O. Box AC Zevenbergen The Netherlands BEAST CORE RIG OPERATING MANUAL 15

16 LACKMOND.COM BEMBCR-1612V2 BM V