INSTRUCTION MANUAL. Thank you for purchasing the Ice Factory.

Transcription

1 IceAge Anleitung_e :17 Uhr Seite 1 IceAge Professional Ice Maker INSTRUCTION MANUAL AP-01A Thank you for purchasing the Ice Factory. Please read this instruction thoroughly before your first use of this product. Keep this manual carefully for future use.

2 IceAge Anleitung_e :17 Uhr Seite 2 Product Description 1. The AP-01 Ice Factory is a elegant, portable, well-designed ice maker. 2. It s micro computerized system makes the whole process of ice cube making completely automatic. AP-01A is designed for using external water inlet pipe for water supply, and as well for manual water filling. 3. The advanced ZEL compressor and cooling system can product ice cubes in high speed and good quality. Daily ice cubes production is max. 20 Kg. 4. Three different size of solid ice cube are available for selection 5. Its Intelligent System keeps all ice cubes in consistent size by adjusting the duration of ice cube making process automatically according to room temperature. 6. This unit are equipped with self-defected detector and protective devices. 7. Its unique design and portability can complement you at Bar, Party Gathering, Yachts, Office or wherever you need. Technical Specifications MODEL: AP-01A DIELECTRIC PROTECTION CLASS: I VOLTAGE: V~ RATED CURRENT: 1.3A FREQUENCY: 50Hz REFRIGERANT/CHARGE: R134A/110g POWER: 200W ICE MAKING CAPACITY: max. 20kg/day. CLIMATE: N.ST WATER INLET PRESSURE: 0.1MPa Mpa INSULATION FOAMING: POLYURETHANE

3 IceAge Anleitung_e :17 Uhr Seite 3 Parts Diagram 1: Water Tank 2: Ice Cube Tray 3: Ice Baffle 4: Ice Maker 5: Control Panel 6: Switch Panel 7: Water Inlet Valve 8: Tap Water Connector 9: Lip Cover 10: Compressor 11: Water Pump 12: Condenser 13: Evaporator 14: Thermo Sensor 15: Mini Water Level Sensor 16: Maximum Water Level Sensor

4 IceAge Anleitung_e :17 Uhr Seite 4 Enclosed Accessory 1. Instruction Manual 2. Water Pipe 3. Ice Shovel (3 sets How to use 1. Remove all packaging materials and labels. Keep the unit at up-right position while lifting up from the packaging to avoid causing damage to the compressor of the unit. The tilt angle can not greater than 45 Degree. 2. Place the Ice Station at up-right position. Keep the unit at least 20CM apart from the wall around for better ventilation and operation. 3. Wash the Water Tank; Cooling System, Ice Cube Tray; Ice Shovel of the Ice Station with washing detergent before each use. 4. Open the Lip Cover, fill the Water Tank with drinking water. When adding water, make sure the water level does not exceed the maximum water level of the Water Tank. If you use the external Water Pipe for adding water, make sure the Water Pipe is firmly connected with the In Coming Water Inlet, open the tap and check to ensure no water leaking in the conjunction part before use. 5. External Water Inlet Installation diagram Water Inlet Connector Water Pipe Valve 3 way water connector 6. Plug in the unit to the power outlet, the Power On Indicator will light, indicating that the machine is in standby status. 7. Control Panel Diagram Power On Indicator Indicator of large size of ice cube Indicator of medium size of ice cube Indicator of small size of ice cube Ice Full Indicator Lack Water Indicator Power On/Off Button Select Button ( Ice Cube Size ) 8. Press the Power On/Off button in the Control Panel to On position to start the operation. The default setting are set for making medium size ice cube. Press the Select button for choosing the size of ice cube, the indicated size of indicator will light accordingly During the operation, press the Power On/Off button to Off position to stop the unit from running. 9. After the unit running for few minutes, the temperature of the unit and water starts dropping, as the flowing water temperature reach zero degree, the water become frozen, the indicated size will blink. Ice cubes making are now in progress. 10. When the ice cubes are formed completely, the indicated size will blink more frequently, 36 pieces of ice cubes will fall into the Ice Cube Tray automatically for each cycle. Once all ice cubes are shoveled, the ice cube making cycle starts again. 11. When the Ice Cube Tray is full, the Ice Full Indicator will blink, the compressor and fan motor will stop running. Remove the ice cubes from the Ice Cube Tray. The same Ice cube making cycle will starts again. 12. Keep pressing the Select button for 3 seconds, the ice cubes inside the unit are forced to melt. Duration of ice cubes making Making large size of ice cube ( around Minutes ) Making medium size of ice cube ( around Minutes ) Making small size of ice cube ( around Minutes )

5 IceAge Anleitung_e :17 Uhr Seite 5 Maintenance 1. Always keep the unit stand still at up-right position while moving to avoid causing damage to the compressor of the unit. 2. Plug the unit into a power outlet alone. Make sure your electricity supply is V~50Hz, the current is 10A. 3. To disconnect the power, grip the plug and pull it from the wall outlet. Never drag the cord. If the power cord is damaged, bring it to the service centre for replacement. 4. The unit should be placed vertically. Do not place the unit near flammable items or fire source. Keep at least 20cm distance from the surroundings for better ventilation and operation. 5. Initially when switching On the unit, it will takes sometimes before water is cooling down to zero degree. Duration of ice cube making will be prolonged if adding more water. 6. If the water level is lower than the minimum water level of the Water Tank, the Lack Water indicator will light, indicating manual water filling is required. If using external water inlet pipe for water supply, the Lack Water indicator will blink, indicating water filling starts automatically. 7. Use only drinking water to make the ice cube. Never use dirty water as it may damage your health. Clean the unit frequently after each usage. 8. Clean the water ejector if water is not flowing well. 9. Install the Ice Cube Tray in correct position to avoid touching the Ice Shovel 10. If no water is adding to the unit when the Lack water indicator light up, the unit will stops running automatically. 11. Always keep the sensors clean from rust for better performance. 12. Do not open the Lip Cover of the unit during running as it may affects the ice cubes making performance. 13. Unplug the unit from the power outlet and remove all ice cubes before cleaning. Use a dilute solution of water and vinegar to clean the interior of the ice maker, and then rinse it with drinking water thoroughly. Do not rinse internal components of this unit. Do not use gasoline to wash this unit. 14. Remove the Drain Plug from the unit to drain the remaining water from the water tank and let it clean and dry when the unit will not be used for a long period. 15. When using the external water pipe for water supply, the unit will stops running if there are no water supply coming from the pipe.

6 IceAge Anleitung_e :17 Uhr Seite 6 Trouble Shooting Before bringing to the service centre, please check the followings: Problems Possible Reasons Solution The compressor makes some unusual noise when the Power On Indicator is On Incorrect power supply. Unplug the unit, and check to ensure correct power supply is used. The Power On Indicator does not light No power supply Bad contact with the power outlet Check both the power cord, power plug and power outlet The Ice Full Indicator keep on blinking Ice Baffle are blocked by ice cubes. It can not works properly Remove the ice cubes, turn off the ice maker. And then turn on again NOTE: Please contact our service centre for replacement if problems are not caused by the above reasons. The unit is in normal good condition if the following occurred The fan is still running for few seconds after switching Off the unit and the compressor. Noise caused by the running compressor and the flowing refrigerant inside the compressor.

7 IceAge Anleitung_e :17 Uhr Seite 7

8 IceAge Anleitung_e :17 Uhr Seite 8 BETEC Herzogstr. 55 D Neu-Isenburg Phone +49 (0) / Fax +49 (0) / info@betec-ideen.de BETEC Art.Nr./Part-No. 4045