INSTALLATION & OPERATING INSTRUCTIONS VILLAGE COLLECTION QV26E ELECTRIC FIREPLACE/INSERT

Transcription

1 INSTALLATION & OPERATING INSTRUCTIONS VILLAGE COLLECTION QV26E ELECTRIC FIREPLACE/INSERT SAVE THESE INSTRUCTIONS Note: Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction resulting in serious injury and/or property damage. CAUTION: Do not expose the heater to the elements (such as rain, etc.). All electric heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are or stored. Do not use where the heater may be exposed to flammable vapors. This heater is tested and listed for use only with the optional accessories listed in these instructions. Use of optional accessories not specifically tested for this heater could void the heater warranty and/or result in a safety hazard. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer. Do not modify this heater. Use it only as described in this manual. Any other use not recommended by the manufacturer may result in fire, electric shock or personal injury and void the warranty.

2 Table of Contents A. Listing Approvals... 3 B. Heater Dimensions... 3 C. Location and Clearances... 4 D. Framing... 5 E. Installation... 6 F. Wiring... 9 G. Finishing H. Final Installation I. Operating Instructions J. Maintenance Instructions K. Troubleshooting L. Optional Components M. Replacement Parts Warranty IMPORTANT INSTRUCTIONS! When using electrical heaters, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 1 ft (.31m) from the front of the heater and keep them away from the sides and rear. 3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. 4. Always unplug heater when not in use. 5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair. 6. Do not use outdoors. 7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container. 8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over. 9. To disconnect heater, turn controls to OFF, then remove plug from outlet. 10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 11. To prevent a possible fire, do not block air intakes or exhaust in any manner. 12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. 13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. 14. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 16 AWG minimum size and rated not less than 1875 watts. 15. Always use properly grounded fused and polarized outlets. 16. Always use ground fault protection where required by electrical code. 17. Always disconnect power before performing any cleaning, maintenance or relocation of the heater. 18. To prevent a possible fire, do not burn wood or other materials in this heater. 19. To prevent electric shock or fire, always use a certified electrician should new circuits or outlets be required. 20. When transporting or storing the heater, keep in a dry place free from excessive vibration and store as to avoid damage. 21. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. 2 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

3 U.S. And Canada Certification A. LISTING APPROVALS The QV26E heater has been tested in accordance with the UL2021 Standards for fixed and location-dedicated electric room heaters in the United States, the current CSA C22.2 NO. 46 in Canada and has been listed by Underwriters Laboratories Inc. for installation as described in this manual. All components are UL or CSA safety certified. If you need assistance during installation, please contact your local dealer or the Quadra-Fire Technical Services Department at Quadra-Fire is a registered trademark of MODEL Description Voltage Watts Amps (120/208/240) QV26E 26 in. fireplace/insert B. HEATER DIMENSIONS 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 3

4 C. LOCATION AND CLEARANCES Due to high temperatures, this heater should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 1 ft [.31M] from the front of the heater. Never locate this heater where it may fall into a bathtub or other water container. Note: Minimum and maximum clearances must be maintained at all times. Illustrations throughout these instructions reflect typical installations and are for design purposes only. Actual installation may vary slightly due to individual design preferences. The illustrations and diagrams used throughout these installation instructions are not drawn to scale. CAUTION: Do not expose the heater to the elements (such as rain, etc.). To prevent contact with sagging or loose insulation, the heater must not be installed against vapor barriers or exposed insulation. Localized overheating could occur and a fire could result. 1. Heater Locations and Space Requirements Figure 1 illustrates a variety of ways the heater may be located in a room. The QV26E heater may be installed directly on the floor, carpet or raised on a hearth. 2. Clearances Figure 1 shows all clearances that must be maintained around the heater. CAUTION: Wear gloves and safety glasses for protection during installation and maintenance. Figure 1 - Heater Locations 4 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

5 D. FRAMING Figure 2 shows a typical framing of this heater using combustible materials. All required clearances to combustibles must be adhered to. Header height is measured from the base of the heater. Figure 2 - Framing CAUTION: Provide adequate clearances around the air openings and adequate accessibility clearances for servicing and proper operation. Tools and building supplies normally required for installation: Tools: Saw Pliers Hammer Phillips screwdriver Tape measure Level Electric drill/bits Square Gloves Building Supplies: Wall-finishing materials Framing material Surround Caulking material 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 5

6 E. INSTALLATION WARNING - RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce the risk of fire, electric shock or personal injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. This heater is tested and listed for use only with the approved optional accessories. Use of optional accessories not specifically tested for this heater could void the heater warranty and/or result in a safety hazard. WARNING - RISK OF FIRE! To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces (like a bed) where openings may become blocked. CAUTION: When transporting or storing this heater and cord, keep in a dry place that is free from excessive vibration. Store so as to avoid damage. WARNING - RISK OF FIRE! Do not blow or place insulation against the firebox. If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other heater. 1. As a Fireplace (see Step 2 for installation as an insert) Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas. Note: Follow all national and local electrical codes. a. Wall Cabinet Kit, Corner Cabinet Kit or Custom Cabinet Installation The Cabinet must provide access to the wall outlet. 1) For ease of electrical hookup, you may wish to install the heater near an existing outlet. A 15 amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit trips or fuse blows on a regular basis while the heater is operating. Additional heaters on the same circuit may exceed the current rating of the circuit breaker. 2) If using a wall cabinet or corner cabinet, refer to the installation instructions supplied with the kit. For custom cabinets, frame and construct with the opening and depth dimensions listed in Figures 1 and 2. 3) Before plugging the heater into the wall outlet, make sure all control switches are in the OFF position. 4) Before finishing the cabinet, the heater must be set into the cabinet and the power cord routed to the electrical outlet. If the power cord does not reach the outlet, a No. 16-AWG minimum wire size extension cord rated for a minimum of 1875 watts may be used. 5) To complete the heater installation, refer to Section H. Final Installation. b. Non-Cabinet or Chase Installation 1) Follow recommended framing dimensions in Figures 1 and 2. 2) Set the heater into the framed opening. Secure the heater in place using the nailing flanges on both sides of the heater and nail to the framing. 3) To finish out the heater, follow the instructions found in Section G. Finishing. 4) To complete heater installation, see Section H. Final Installation. C. Proceed to Step /04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

7 2. As an Insert a. Pre-installation Preparation This insert and its components are tested and safe when installed in accordance with this manual. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any heater with damaged, incomplete or substitute parts. The front faces are shipped in separate packages. Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner s warranty and may present a fire hazard. The warranty will be voided by, and Quadra-Fire disclaims any responsibility for, the following actions: 1) Installation of any damaged heater. 2) Modification of the heater. 3) Installation other than as instructed by Quadra-Fire. 4) Installation and/or use of any component part not manufactured and approved by Quadra-Fire not withstanding any independent testing laboratory or other party approval of such component part or accessory. Any such action may possibly cause a fire hazard. b. Installation 1) Quadra-Fire inserts are designed for installations into solid fuel masonry or factory built noncombustible fireplaces that have been installed in accordance with the national, provincial, state or local building codes. 2) Minimum fireplace opening requirements are shown in Figure 2 of this installation manual. The firebrick (refractory) can be removed from a factory built fireplace in order to gain minimum insert opening requirements. 3) This insert requires no hearth extensions. Combustible material on the floor may be installed up to the insert. Do not obstruct the lower grill of the insert. The original fireplace cannot be returned to solid fuel in this condition. 4) The metal floor of the solid fuel firebox may be removed to facilitate the installation of the insert. The side walls and top structure of the firebox may not be altered with the exception of removable baffles and dampers. The original fireplace cannot be returned to solid fuel in this condition. 5) Position, Level and Secure Insert a) Place the heater into position. b) Level the heater from side to side and from front to back. If necessary, use the leveling bolts included in the manual bag. Screw the bolts into the nuts installed in the bottom of the insert (see replacement parts diagram). Turn the bolts until the insert is level. c) A retaining method may be needed to secure the heater in place. 6) Combustible facing material may be installed over the original combustible or noncombustible facing material on the solid fuel fireplace. The original specified clearances of a factory-built fireplace must be maintained, with the exception of the hearth. Clearances on a masonry fireplace must be maintained at 12 in. from the opening for combustible projections over 1-1/2 in. Clearances for combustible projections under 1-1/2 in. must be maintained per NFPA 211. Plan the surround size accordingly. A front face must be used with the insert. 7) The insert front face is tested and approved with this insert and may cover existing air circulation vents or grilles on the solid fuel fireplace it is installed into. Should the face not cover the entire ventilation grille surface, the grille should be left open. 8) The solid fuel fireplace s flue damper must be fully locked in the closed position or removed for installation. Note: Decorative trim front faces have been tested and approved to cover existing air circulation vents or grilles. 9) The chimney must be capped. 10) Install the insert without the front face and make all electrical connections. Note: The warning label above, located in the instruction package, must be affixed to the lower back wall of the existing fireplace prior to installation of the insert. CAUTION: To avoid downdrafts, moisture and/or cold air problems, we recommend that you seal off the area between the termination cap and the top of the existing chimney opening. Note: When the front is installed it will cover the gap between the heater and the framing, cabinet, finishing materials or existing fireplace. 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 7

8 F. WIRING Note: This heater must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C2.1 as appropriate. All wiring must be done by a qualified electrician. Use appropriate wire to meet local and national codes for rated power consumption. 1. Fireplace a. The heater is wired from the factory with a polarized plug. No provisions have been made for hard wiring. b. For ease of electrical hook up, you may wish to install the heater near an existing outlet. A 15 amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit trips or fuse blows on a regular basis when the heater is operated. Additional appliances on the same circuit may exceed the current rating of the circuit breaker. c. Before plugging the heater into the wall outlet, make sure the control switch is in the OFF position. d. If the cord does not reach the outlet, a No. 16-AWG minimum wire size extension cord rated for a minimum of 1875 watts may be used. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. 2. Insert Heater Requirements This heater requires VAC to operate. Run the cord out the notch in the front face and plug into a convenient outlet. If permitted by local codes, an electrician may install an outlet box inside the existing fireplace. Place the outlet in the lower back of the firebox. Note: Electrical wiring must be installed by a licensed electrician. CAUTION: Disconnect remote controls if you are absent for extended periods of time. This will prevent accidental operation of the heater. 8 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

9 CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Always use properly grounded, fused and polarized outlets. Always use ground fault protection where required by electrical code. Figure 3-110V/120V Wiring Diagram 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 9

10 1. Combustible Finishing Material Materials made of or surfaced with wood, compressed paper, plant fibers, plastics or any material capable of igniting and burning, whether flame proofed or not, plastered or unplastered (this includes drywall). 2. Noncombustible Finishing Material Materials which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters or combinations thereof, or have a UL Fire rating of Zero (0). Grilles on this heater cannot, in any way, be covered as it may create a fire hazard. G. FINISHING 3. Finishing Checklist a. Power supply service must be completed prior to finishing to avoid reconstruction. b. Grilles and air openings cannot be covered in any circumstances. Figure 4 - Finishing Materials Note: The heater is a zero clearance fireplace and may be finished with combustible or noncombustible finishing materials. When using paint or lacquer to finish the mantel, they must be heat-resistent to prevent discoloration. Note: Finishing materials are normally installed behind the nailing flanges or up to the sides of the nailing flanges. Allow room for the front to be added and the heater to be anchored /04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

11 H. FINAL INSTALLATION WARNING - SHOCK HAZARD! -- DO NOT operate this heater without the front face installed. 1. Ember Bed Rock Open the bag of ember bed rock and spread it over the ember tray. This will create the effect of burning embers. Not all of the black and white rock needs to be used. See Figure Install the Grate (on top of the ember bed rock) Unpack the grate and attach it to the hearth panel using the screws provided. Use the holes found at either end of the grate/hearth panel. 3. Install the Front Face Install the front face following the instructions packaged with the face. Installation of other optional accessories may be done at this time. The heater is now ready to operate. See Section I. Operating Instructions. Figure 5 - Placing the Ember Bed Rock I. OPERATING INSTRUCTIONS The operating controls are located on the upper right edge of the heater. 1. Main Power Switch The main power switch is a three-position switch. a. Heater ON - Lights bright, thermostat active. b. Heater OFF - All off. c. Heater ON - Lights dim, thermostat active. 1) When the main power switch is turned ON, it provides power to all functions. 2) When used in conjunction with the optional remote control, the switch should remain in an ON position. 2. Thermostat a. Active only when lights are on. b. The thermostat allows you to adjust the desired room temperature. c. Set at maximum - always on below 104 F. d. Set at minimum - always off above 32 F. 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 11

12 J. MAINTENANCE INSTRUCTIONS Always disconnect power and allow the heater to cool before performing any cleaning, maintenance or relocation of this heater. Turn controls to OFF and remove the plug from the outlet or turn off the circuit breaker to the heater. 1. Access the Firebox a. Turn the heater off and turn off the circuit breaker. b. Allow the heater to cool before cleaning. c. Remove the front face to access the log area. 1) Remove the screws from the switch bracket. 2) Remove by pulling out the bottom of the front and then lifting up d. Replace all parts after cleaning or bulb replacement has been completed. e. Reset the circuit breaker. 2. Clean the Firebox Compartment Use the brush attachment and gently vacuum the compartment. 3. Clean the Back Glass a. The glass is cleaned in the factory during the assembly process. During shipment, installation, handling, etc., the glass surface may collect dust particles. These can be removed by buffing lightly with a clean dry cloth. b. To remove fingerprints or other marks, the glass can be cleaned with a damp cloth using a good quality household glass cleaner. The glass should be completely dried with a lint free cloth or paper towel. c. In the event of glass breakage, vacuum all remaining glass pieces with a shop vac. DO NOT VACUUM IF PIECES ARE HOT! Replace the glass with a Quadra- Fire glass panel ordered direct or through your local distributor. Never use substitute material. Only fully tempered soda lime safety glass may be used on this heater. 4. Replace the Light Bulbs The light bulbs need to be replaced when the flame and/or ember bed is dark on one side. Replace the bulbs with 75 watt halogen bulbs with mini-candelabra base. Do not exceed 75 watts per bulb. Light bulbs can be purchased at a local hardware or lighting store, on-line or by phone. To order on-line, log onto or call We recommend you use Sylvania model SL58884 or Satco model S3157. a. Light bulb access is through the ember bed. See Figure 6. b. Locate and lift the bent tabs holding the ember tray located at each end of the ember tray. c. Lift out the ember tray. d. Carefully remove the burned out bulb from the light socket. Place the new bulb in the socket. See Figure 7. Follow directions on the light bulb package for handling requirements. e. Reinstall the ember tray. Figure 6 - Bulb Access Figure 7 - Replacing the Bulbs 12 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

13 K. TROUBLESHOOTING Issues Heater doesn't turn on with the main switch or remote transmitter. Heater is on, but no flame or low flame intensity. Flames are frozen. Possible Causes Solutions 1. Power switch is off. 1. Turn the power switch to the "ON" position. 2. Circuit breaker is tripped 2. May need to put the heater on a dedicated service or reduce the number of appliances on the circuit. 3. Heater is unplugged from wall outlet. 3. Plug the cord into an outlet. 4. Loose wiring. 4. Check all wiring for loose connections. 1. The bulbs are burned out 1. Replace the bulbs. 2. Loose wiring. 2. Check all wiring for loose connections. 1. Loose wiring. 1. Check all wiring for loose connections. 2. Flame element is not attached to the motor. 2. Reattach the flame element to the motor. Excessive noise in the lower portion of the heater. Heater system doesn't come on. Fan runs but not heat is put out. Heater element is on but fan doesn't run. 3. Motor is defective. 3. Replace the motor. 1. Flame element isn't seated properly. 1. Reinstall the flame element. 2. Motor is defective. 2. Replace the motor. 1. Heater switch is off. 1. Turn the heater switch to the "ON" position. 2. Thermostat is set too low. 2. Move the thermostat slide until you hear a "click". 3. Heater system is overheated. 3. The heater system is protected by a thermal cutout switch. Shut off the switch. Wait five minuites, then turn the heater on. 4. Loose wiring. 4. Check all wiring for loose connections. 1. Loose wiring. 1. Check all wiring for loose connections. 2. Bad heating element. 2. Replace the heater system. 1. Loose wiring. 1. Check all wiring for loose connections. 2. Fan is defective. 2. Replace the heater system. The heater system doesn't turn off. 1. Thermostat is set too low. 1. Move the thermostat slide until you hear a "click". Excessive noise in upper portion of the 1. Build up of dirt on the fans. 1. Clean all fans. heater. 2. Heater fan is defective. 2. Replace the heater system. Remote control doesn't work. 1. Remote is out of range. 1. Move remote closer to the heater. 2. Low batteries. 2. Replace the batteries. Odor. The heater may emit a slight, harmless odor when first used. This is a normal condition caused by initial heating of the internal parts and will not occur again. 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 13

14 L. OPTIONAL COMPONENTS Remote Control RC-ELEC-QUAD Remote Control Trim Kits PBT26EA SST26EA PBT = Polished Brass Trim SST = Stainless Steel Trim PBT26ER SST26ER Cabinets Several styles of cabinets are available for use with these heaters. See your dealer/distributor for styles and sizes /04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

15 Fronts DF-26ERA-BK2824 DF-26ESP-BK2824 DF-26ERA-BK4028 DF-26ESP-BK4028 DF-26ERA-BK4432 DF-26ESP-BK4432 Model Description Width Height DF-26ERA-BK2824 Remington Avenue 28 in. 24 in. DF-26ESP-BK2824 Sun Prairie 28 in. 24 in. DF-26ERA-BK4028 Remington Avenue 40 in. 28 in. DF-26ESP-BK4028 Sun Prairie 40 in. 28 in. DF-26ERA-BK4432 Remington Avenue 44 in. 32 in. DF-26ESP-BK4432 Sun Prairie 44 in. 32 in. 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 15

16 M. REPLACEMENT PARTS 16 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

17 REPLACEMENT PARTS (con t) # Description of Part Replacement parts are available from your distributor/dealer. QV26E Qty. R 9 Grommet Y 7 Halogen Light Y 6 Light Receptacle Y 14 Top Magnet Assy Y 4 Parabolic Reflector Y Power Cord Y 8 Flame Element Assy Y 2 Heat Shrink Tube Y 1 Motor Y 21 23/26 Log Assy Y in. Flame Panel Y 5 Light Support Y 3 Motor Bracket Y in. Ember Tray Y 15 Heater/Blower Assy Y in. Back Glass Y in. Lenticular Lens Y in. Insert Ember Bed Y 17 Leveling Bolts Y 18 Thermostat Control Assy Y Installation Manual Y 22 QV26E Grate Assy Y 23 Refractory-LH-26 in Y 24 Refractory-RH-26 in Y Rock, 20 oz. bag Y 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 17

18 This page intentionally left blank /04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT

19 This page intentionally left blank. 04/04 VILLAGE COLLECTION ELECTRIC FIREPLACE/INSERT 19

20 WARRANTY (HHT) Electric Fireplaces are tested and inspected prior to shipment and are guaranteed from defect to the purchaser of each new product. Any part which proves to be defective in material or workmanship under normal use within one year will be repaired or replaced without charge.* The Company will not be responsible for any expense incurred for installation, removal from service, or transportation costs. Any such defect should be brought to the attention of the Dealer where the product was purchased and is authorized to repair or replace within the terms of this warranty. The Company s only obligation under this warranty will be at its sole option to repair or replace any part proving defective or to refund the purchase price thereof. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the use of or inability to use the product. The warranty will not apply if, in the sole judgement of the Company, damage or failure has resulted from accident, alteration, misuse, abuse, incorrect installation, or operation on an incorrect power source. The foregoing is in lieu of all other warranties expressed, implied, or statutory, and the Company neither assumes, nor authorizes any person to assume for it any other obligation, or liability in connection with said product. *Light bulbs are not covered in the warranty. How to Obtain Service. To obtain service under this warranty you must: 1. Send written notice of the claimed condition to Quadra-Fire Technical Service Department, Hearth & Home Technologies Inc.,. 2. Provide proof of purchase, model number, serial number, and manufacturing date code to HHT. 3. Provide HHT reasonable opportunity to investigate the claim, including reasonable opportunity to inspect the Heater prior to any repair or replacement work and before the Heater or any component of the Heater has been removed from the place of original installation. 4. Obtain HHT s consent to any warranty work before the work is done. ADDITIONAL INFORMATION. If you would like information on current Quadra-Fire products or want to locate a dealer in your area, call Quadra-Fire is a Registered Trademark of 20 04/04 QV26E SERIES ELECTRIC FIREPLACE/INSERT