SFP3-14-GB INFLATABLE S EXPERT SAND FILTER PUMP MANUAL

Transcription

1 2014 SFP3-14-GB INFLATABLE S EXPERT SAND FILTER PUMP MANUAL 1

2 Specifications Model JL29P423NG Voltage V Power 65 W Max. operation pressure 1bar (15psi) Effective filter area 0.05m² (0.57ft²) Max. water flow rate 800 gal/h (3000L/h) Rated filter flow rate 530 gal/h(2000l/h) Max. water temperature 35 Recommended filter medium 20# quartz sand or glass sand Particle size: mm Recommended medium amount 9Kg of quartz sand or glass sand Please read the following instructions carefully and keep them for future reference. Safety Instructions Basic safety precautions for installing and using the product should comply with the following. 1.Warning: To reduce risk of injury, do not allow children to use the product. Children and the disabled must be supervised closely at all times. 2.Warning: Keep children away from the product and wires. 3.Warning: Children must be carefully supervised to ensure they cannot access the 4.product. 5.Warning: The product must be kept away from the pool to avoid children climbing on it. 6.Warning: To avoid the risk of electric shock, connect the product with a grounded receptacle protected by electrical leakage. If you are unable to confirm, please contact an experienced electrician for installation. Maximum leakage current is 30mA, so please do not use a movable receptacle. 7.Warning: Always unplug the product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product. 8.Warning: Do not bury the power cord. Place the cord where it cannot be damaged by a lawn mower or other equipment. 9.Warning: Do not use the product if the power cord is damaged. 10.Warning: To reduce the risk of electric shock, do not connect the extension cord, timer, adapter or converter plug to the filter body. Please provide a permanently installed receptacle. 11.Warning: Do not attempt to unplug the product with wet hands or while standing in water. 12. Attention: After assembly, the plug shall be placed in such a way that it is easily visible and accessible to the user. 2 SFP3-14-GB

3 Attention: Always keep the product at least 2m away from the pool. 14. Attention: Always keep the plug at least 3.5m away from the pool. 15.Warning: Never start the product while the pool is in use. 16.Warning: Adult assembly and operation are required. 17.Warning: This product is designed for use with movable pools only. It must not be used with permanently installed pools. A movable pool is a device that can be easily assembled & disassembled for water storage. 18.Warning: To prevent the product from any damage, please turn it off before turning the control valve. 19.Warning: To reduce the risk of being sucked into ot towards the pump never enter the water when the filter hood is loose, damaged, destroyed or lost. Please replace the filter hood immediately if any of the above situations pertain. 20.Warning: Do not play or swim near the filter hood. Your body or hair may be caught in the pump which can lead to permanent injury or drowning. 21.Warning: Do not start the product when the data displayed on the manometer on its body exceeds the maximum value specified. 22. Warning:The maximum total head, 1.5 in metres (for pumps having a rated power input exceeding 50 W) 23. Warning:The pump is to be supplied by an isolating transformer or supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 ma. 24. Warning:The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped. 25. Warning:This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. 26. Attention: The product is intended for use for those purposes detailed in the manual only. WEEE Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. 3 SFP3-14-GB

4 Read Important Safety Instructions and Follow all Safety Cautions Parts List FIG. 01 No. Name Quantity No. Name Quantity P1 Manometer 1 P2 Control 1 valve P3 Drain nut 1 P4 Adapter 2 P5 Seal ring of 1 P6 Control 1 control valve valve retainer P7 Control 2 P8 Body 1 valve screw P9 Central connecting pipe 1 P10 Pedestal 1 P11 Drain valve 1 P12 Connecting pipe 1 P13 P15 Slag blocking screen Cover of slag blocking barrel 1 P14 Seal ring of slag blocking barrel 1 P16 Positioning plate P17 Strap 6 P18 Water pipe Installation Instructions FIG. 02 Tools required: 1 Phillips screwdriver Product installation position and assembly: The product must be installed on firm and level ground. Provide sufficient space and light for the convenience of daily maintenance. The motor must be ventilated for cooling. Do not put the product in a wet place with no ventilation. At least 2 persons are recommended to install the product. 1. Position the product in the place selected. 2. Make sure the connection between the body and the pedestal is good. Important note: the product must be positioned on the ground or a permanently upward pedestal in some EU countries. To determine whether there are any regulations on surface pool filters consult the local authorities. If any, fix the filter using two holes drilled in a platform. (See FIG. 02) The sand filter pump should be secured on a cement pedestal or wood platform to avoid it tipping over. Note: the hole diameter of the pedestal is 6.4mm. Note: the maximum diameter of the two screws and lock nuts used is 6.4mm. 4 SFP3-14-GB

5 2014 I. Sand Filling Note: use 20# quartz sand or glass sand. Particle size of the sand is mm. Note: before sand filling, make sure the central connecting pipe (P9) is connected at the bottom of the body and vertically stands in the center of the body (see FIG. 03). 1.First, sleeve the positioning plate (P16) onto the top of the central connecting pipe. (See FIG. 04) 2.Then pour sand into the body slowly. (See FIG. 05) 3. When the sand is near to the half way level, remove the positioning plate, spread the sand evenly with one s hands, and pour in more sand so that the filling of the remaining sand is buffered. This can help avoid excessive vibrations of the central connecting pipe (P9). Afterwards, ensure the positioning plate (P16) replaced properly and keep pouring sand. 4. Remove the positioning plate (P16) (see FIG. 06) and spread the sand evenly with one s hands 5.Clear away the sand around the top of the body. FIG. 03 FIG. 04 FIG. 05 FIG. 06 FIG. 07 FIG SFP3-14-GB

6 II. Installation of manometer 1. Take out the manometer from the package, check whether that the seal ring is present. 2. Screw the manometer onto the control valve in a clockwise direction until tightly fixed. FIG. 09 III. Installation of control valve 1.Check whether the seal ring of the control valve (P5) is properly positioned, then place the control valve (P2) onto the top of the body slowly, and ensure the port at the bottom of the control valve is closely inserted into the port on the top of the central connecting pipe (P9) (FIG. 06, 07). 2. There are 3 port connecting points on the control valve. It is essential to ensure Port A points towards the pool, and that Port C of the control valve is aligned with Port C of the motor. (See FIG. 10) 3. Remove the screw group on the control valve retainer, clamp the control valve retainer around the flange between the body and the control valve, and then pass the screw group through the drilled clip nuts and tighten with a screwdriver (not provided) (see FIG. 08). FIG. 10 II. Installation of manometer 1. Connect one end of a corrugated pipe (P18) to Port B, the other end to port F of the pool. Secure tightly with a strap (P17). 2. Connect one end of the connecting pipe P12 to Port C of the control valve, the other end to Port C of the motor. Secure tightly with the strap 6 SFP3-14-GB

7 2014 (P17). 3. Connect one end of the other corrugated pipe (P18) to Port A of the control valve, the other end to Port E of the pool. Secure tightly with the strap (P17). 4. Check to confirm whether the installation is finished properly, afterwards use the sand filter pump to filter the pool water. Instructions for use I. Location and functions of the control valvecontrol valve Signs Location Functions of control valve Filter Normal filtering to rinse the pool Water flow direction Water flows through the filter bed where the sand filter pump lies and then enters the pool Backwash Reverse-direction water Water flows through the flow to rinse the filter filter bed where the sand bed filter pump lies and is then directly discharged from the drain outlet. Rinse This function is used Water flows through the for first startup. Sand in filter bed where the sand the sand tank is rinsed filter pump lies and is and the sand bed after then directly discharged backwashing is leveled. from the drain outlet. Drain Discharged directly Discharged directly from from the drain outlet, the drain outlet of the used to lower water sand filter pump without level or discharge water passing through the filter from the pool bed Circulation Circulates pool water Water flows directly without passing through into the pool through the filter bed. the control valve of the sand filter pump without passing through the filter bed Closed Closed water flow between the filter and the pool 7 SFP3-14-GB

8 II. Operation of the control valve Warning: Before operation, make sure all corrugated tubes are properly connected and locked and the filter has been filled with the correct amount of sand. Warning: Before operation, make sure the product is disconnected from the grounded receptacle protected by electrical leakage. Warning: The control valve is provided with one closed valve position. Do not attempt to start the product when the control valve is in the closed position. 1.When rotating the control valve, press the control valve handle first, then rotate the handle to the required position (see FIG. 11). III. Draining procedure FIG Make sure the product is poweredoff. 2.Remove the drain nuts (P3) first, then move the adapter (P4) at Port A and water pipe (P18) to Port D (see FIG. 12). 3.Press the control valve handle downwards and rotate it to the draining position, and then turn the power on. Perform draining until clean water is discharged (see FIG. 12). After draining, disconnect the power. 4.Rotate the control valve handle to backwashing position. Power on again, until clean water flows, then backwashing finishes. Disconnect power (see FIG. 12). 5.Remove the adapter (P4) at Port D and water pipe (P18) and return them to Port A (see FIG. 10). 6. Return the drain nut (P3) to Port D (see FIG. 10). 7.Power on and select the required function position. Begin operation. Note: this step is for first operation only. Note: do not attempt to set between two functions of the control valve to avoid possible leakage. III. Draining procedure 1.After the aforementioned preparations, the sand filter pump is ready for use. Set the filter function of the control valve. 2.Insert the plug into the matched receptacle to run the sand filter pump. Note: During the operation of the sand filter pump, check the pressure reading of the manometer (P1). Generally, when the pressure of the recommended FIG SFP3-14-GB

9 2014 sand filter pump is less than 0.2bar (3psi) (green area) (see FIG. 14), it runs normally. V. Sand Filter Pump Maintenance Note: You must make sure that maintenance begins only after the sand filter pump is unplugged. Otherwise serious risks such as personal injury and even death may occur. Note: Record the reading of the manometer during the operation of the sand filt er pump (see FIG. 15). When the manometer shows a pressure of 0.2bar (3psi) or higher, please clean up the sand bend or replace the sand. Use "backwash" and "rinse" functions. Note: regular rinsing according to use situation is recommended. FIG. 15 VI. Motor and Slag Blocking Barrel Cleaning and Maintenance 1.It is essential to make sure the power cord is removed from the receptacle. 2.Block the water outlet of the pool. 3.Unscrew the slag blocking cover (P15) on the slag blocking barrel in an anticlockwise direction, take out the slag blocking screen (P13) and the seal ring (P14). 4.Rinse the slag blocking screen with a water pipe. If necessary, use a plastic brush to remove impurities. Do not use a metal brush. 5.Rinse the inside of the slag blocking screen and the seal ring of the slag blocking barrel with a water pipe 6.Install the seal ring (P14) of the slag blocking barrel, the slag blocking screen (P13) and the cover (P15) of the slag blocking barrel in their original positions (see FIG. 13). 9 SFP3-14-GB

10 Long-term storage and storage in winter Using the product in a frozen pool may damage the product and invalidate the quality warranty. If the product has to be used with antifreeze, propylene glycol may also be used. Propylene glycol is a nontoxic chemical unharmful to any plastic parts. Other types of antifreeze are highly toxic and may be harmful to the product s plastic elements. 1.Before discharging the water or repostioning of the pool, make sure the discharge direction is towards the discharging ditch and away from the home. Review local regulations for special water treatment requirements. 2.Switch off the product and remove the power plug. 3.After emptying, remove all connected sand filter pumps, corrugated tubes and filter hoods on the pool wall. 4.Unscrew the drain valve (8) in an anticlockwise direction to completely empty water inside the body. The drain plug is at the bottom of the body. 5.Dry the parts of the sand filter pump and corrugated tubes. 6.Lubricate the seal rings and washers in the order below for long-term storage. 8.The best practice for product storage is to dry the parts and motor and replace them in the original package. To avoid shrinkage or corrosion, do not cover or wrap the motor with a plastic bag. 9.Please store the motor and parts in a dry place at 32 F (0 C) ~104 F (40 C) SFP3-14-GB

11 2014 Diagnosis of Problems and Solutions Problems Checking Solutions The motor can not be started normally Filter Unable to rinse the pool The filter is unable to discharge water or the water flow rate is too slow Filter fails to run Water leakage on the control valve or upper cover The manometer fails to run Power plug not properly inserted Leakage protection disconnected Motor overheated or overloaded Causes motor to stop No sand in the body Location error of the control valve Excessive dirt in water Filter barrel blocked There is blockage at the inlet There is an air leakage at the gap of the inlet Excessive dirt in water Filter medium is blocked by impurities The pool is connected with a cleaning device Make sure the power cord is inserted into the 3-core grounded metal receptacle. Reset circuit breaker. If the problem persists, the power system may be defective. Power off immediately and confer with an expert. Allow the motor to cool naturally and start it again. Sand filling Refer to sand filling instructions The control valve rotates to the filter position to prolong the running time Clean the filter barrel Check and clear away the blockage in the water pipes Tighten the nozzle nuts and check the damaged point of the nozzle and water height Clean the filter screen Backwash Disassemble the cleaning device connected to the pool Water level is too low Inject water to adjust water level Filter screen is blocked Clean the filter screen in the pool Air leakage from the inlet Tighten the nozzle and check the damaged point pipe Replace the fittings Motor or blade is blocked The seal ring of the body is lost or too dirty The control valve retainer is not tightly secured ordamaged The inner wall of the manometer is blocked The manometer is damaged Remove the upper cover of the control valve and sleeve the seal ring of the body Clean the seal ring of the body with a water pipe Tighten the screw with a screwdriver Replace the fittings Remove the manometer from the control valve and clear away the impurities on the inner wall Replace the fittings Sand enters the pool The sand particles are too fine Use 20# quartz sand only Particle size of the sand is mm Or replace the sand 11 SFP3-14-GB

12 After Sales Service Centers For service questions or to order replacement parts, please listed below or visit www. jilong.com for answers to most frequently asked questions.contract the appropriate office UK BML UK Benross House,Bridge Industrial Estate, Speke Hall Road, Liverpool, L24 9WD, UK Tel: USA / CANADA / MEXICO JILONG PLASTIC PRODUCTS NORTH AMERICA INC. 271, EAST 2ND AVENUE VANCOUVER B.C. V5K 1J1 CANADA Tel: service@jilong.com DENMARK HP Schou Industrivej 67,7080 Borkop Tel: service@hpv.dk FINLAND HP Schou Jorvaksen myllytie 5 Jorvas kvarnväg JORVAS Tel:358(0) uv@tradewind.fi NETHERLANDS / BELGIUM / LUXEMBURG Aqua-fun Icarus CJ Heerenveen Tel Fax service@aqua-fun.info RUSSIAN АСБ-Рейтинг , г. Москва, 2-й Донской проезд, д. 7/1 Тел.: +7 (495) (многоканальный) по рабочим дням с 9.00 до Факс: +7 (495) Электронная почта: refer@hoztorg.ru BRAZIL Sérfi Marketing & Sales e Representações Ltda Al. Tambaqui, 59 - Residencial 11 - Alphaville Santana de Parnaíba/SP CEP: CNPJ: / sac@serfi.com.br / 55(11) FRANCE / ITALY / SPAIN / PORTUGAL Jilong Europe Srl unipersonale Via Vitaliano Brancati, Roma Itali Tel:France Italy service@jilong-europe.com GERMANY / AUSTRIA HEISSNER GmbH(pools/spas) Schlitzer Straße 24 D Lauterbach,Germany Tel: info@heissner.de SWEDEN HP Schou Åsvägen 2 E, Hässleholm Tel: service@hpverktyg.se NORWAY Osjord Luramyrveien 64 Postbox 152,4065 Stavanger Tel: ArntEinar.Gjovag@osjord.no POLAND / CZECH / SLOVAKIA / HUNGARY SASKA SP. Z O.O. Ul. Marynarki polskije 59a gdansk poland Tel: , saskasprzedaz@wp.pl CROATIA / SLOVENIA / BOSNIA /SERBIA Eurom Denis d.o.o Borongajska 81a, Zagreb Hrvatska tel.: eurom@eurom.hr ASIA 上海吉龙塑胶制品有限公司上海浦东新区川沙黄楼栏学路 号 Tel: info@jilong.com 12 SFP3-14-GB