IMPORTANT SAFETY INSTRUCTIONS:

Transcription

1 PRODUCT NAME: Hadley 4 Light Pendant ITEM NUMBER: LC813 DIMENSIONS OF ITEM ASSEMBLED: Small: 18 1/2 H x 11 Square Large: 25 H x 16 Square IMPORTANT SAFETY INSTRUCTIONS: -A licensed professional electrician should install direct wire fixtures. -For your safety, please read instructions carefully and completely before beginning assembly or installation. -Fixture must be installed according to applicable code(s) by a person familiar with its construction and operation. -Fixture rated up to 60 Watt MAX Type B INCANDESCENT Bulbs (NOT Included). LED bulbs recommended at lumens, 2700K Warm or Soft White. -Prior to installation or removal of a previous fixture, disconnect power by turning off circuit breaker at electrical panel. WARNING: -Deviation from assembly instructions may cause risk of fire or electric shock. -To reduce risk of personal injury, always turn off fixture and allow bulbs to cool prior to replacement. -Do not touch or look directly at illuminated bulbs. -Keep flammable material away from illuminated bulbs. PRODUCTS ARE NOT INTENDED MADE IN CHINA FOR COMMERCIAL USE. Page 1 of 5

2 Remove all parts, hardware and protective packaging from carton and carefully arrange on a clean, level surface. NOTE: To avoid accidentally discarding small parts or hardware, retain all carton contents until after assembly and installation are complete. Recommended Location for Use: Dry or Damp Environment Fixture Loop (D) Assembly Time: 20 Minutes People Required: 2 or More People Tools Required: Screwdriver, Wire Strippers, Wire Cutters, Electrical Tape Fixture Body (C) Parts (A, B, E-L) PARTS Check to make sure you have the following: INCLUDED: NOT INCLUDED: 1- Canopy 1- Fixture Loop (D) 4-60 Watt Max Type B Candelabra Bulbs 1- Nipple (E) 1- Canopy Loop 1- Chain 2- Mounting Screws (F) 1- Lock Washer (J) 3- Wire Connectors (G) 1- Nut (K) 1- Fixture Body (C) 1- Collar 1- Mounting Bar Page 2 of 5

3 (D) STEP 1: ASSEMBE FIXTURE Thread the Fixture Loop (D) onto the nipple at the top center of the Fixture Body (C). (C) STEP 2: ASSEMBLE CROSSBAR Attach the Nipple (E) to the Mounting Bar by screwing in the Nipple and locking it on the opposite side with the Lock Washer (J) and Nut (K). (K) (J) (E) STEP 3: ATTACH MOUNTING BAR Secure the Mounting Bar to the Oulet Box with the Mounting Screws (F). Tighten until snug. (F) Page 3 of 5

4 STEP 4: ATTACH HARDWARE Attach the Canopy by locking it into place on the Nipple (E) with the Canopy Loop and Collar. (E) STEP 5: ADJUST CHAIN LENGTH Adjust the Chain to your desired length by removing the links if needed. May need chain pliers. Attach one end of the Chain to the Canopy Loop and then attach the other end of the Chain to the loop at the top of the Fixture Body (C). (C) STEP 6: THREAD CORD Weave the Cord and bare Ground Wire through the Chain about every third link. Slide the Collar on the Canopy Loop down with the Canopy. NOTE: To prevent risk fire or electrical shock, the chain must support weight of fixture. DO NOT hang fixture by cord. Page 4 of 5

5 STEP 7: ATTACH ELECTRICAL Trim wires to required length to make connection. Strip ends of 1/2" insulation. Using a wire connector, attach bare ground wire from fixture to bare ground wire in junction box. Wrap both around green screw on Mounting Strap and firmly tighten. The parallel cord attached to fixture is composed of two wires, one smooth and the other ribbed along the edge. The smooth wire connects to the black wire in junction box and the ribbed to white wire. Firmly secure each with a Wire Connector. (See diagram below) (G) WHITE OR RIBBED RIBBED BROWN FROM HOUSE BLACK OR RED OR SMOOTH FROM FIXTURE SMOOTH BROWN FROM HOUSE FROM FIXTURE STEP 8: INSTALL CANOPY Slide Canopy back up the Chain and screw the Collar back into place. STEP 9: INSTALL BULBS (not included) Sockets rated up to 60 Watt Max Type B Candelabra Incandescent bulbs. LED recommended Lumens, 2700K Warm or Soft White STEP 10: Connect breaker and turn on Light. Cleaning & Care: To clean, wipe the Fixture with a soft, dry cloth. Avoid the use of harsh or abrasive chemicals as they may damage the finish. Page 5 of 5