CEILING FAN LIGHT KIT

Transcription

1 CEILING FN LIGHT KIT Owner s Manual Models #20564 If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: , 9 a.m.- 5 p.m. Central time Turn of the Century TM

2 PCKGE CONTENTS Hardware Kit Unpack your light kit and check the contents. You should have the following items: 1. Canopy 2. Downrod 3. Hex Nut PCKGE CONTENTS 6. ulbs (x 3) 7. Light Cage (x 3) 8. Hardware Kit Owner s Manual 4. Lock Washer 5. Light Kit Fitter 9. Owner s Manual 10. Wire Connector (x 2) HRDWRE LIST 15. Mounting racket 11. Hex Nut 16. Cap Nut (x 2) 12. Lock Washer 17. racket Screw (x 2) 13. IP Rod 18. Pull Chain Extension 14. Coupling Note: Some of the hardware listed is pre-assembled to other parts. You will be instructed where to locate it. HRDWRE CONTENTS MOUNTING OPTIONS Ceiling Fan Light Kit Ceiling Light Fixture 2 TM Turn of the Century

3 SFETY INSTRUCTIONS RED LL SFETY INFORMTION ND INSTLLTION INSTRUCTIONS EFORE EGINNING TO INSTLL THE LIGHT KIT ND SVE INSTRUCTIONS. This fixture is intended for use with an indoor ceiling fan. Not suitable for damp or outdoor locations. The fan images and instructions in this manual are generic, but in most cases the installation will be easy to follow. If unsure about installation, consult a qualified licensed electrician for proper installation. WRNING To avoid risk of electric shock, be sure to shut off power at the main fuse or circuit breaker box before installing or servicing this fixture. Turning off the electrical power by using the light switch is not sufficient to prevent electrical shock. Installation must comply with the national electrical code, NSI/NFP and local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a qualified licensed electrician. To avoid personal injury, the use of gloves or protective clothing may be necessary when handling fixture parts with sharp edges. To reduce the risk of fire, electrical shock or personal injury, do not connect this fixture to a ceiling fan is not properly grounded. To reduce the risk of fire, electrical shock, or personal injury, each wire connector used with this light kit should accept only one 18-gauge wire from the light kit and one 18-gauge wire from the ceiling fan. When mounting fixture to a ceiling fan, ensure the fan is mounted to an outlet box labelled cceptable for fan support and is secured to the building structure. Wire colors from ceiling fan may not be the same color used in this manual. When in doubt, consult a qualified licensed electrician to determine the proper wiring. NOTE: The net weight of the light kit is less than: 4.4 lbs. 3 TM Turn of the Century

4 SSEMLY INSTRUCTIONS - FN MOUNT 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 For ceiling mount, skip to page 7. Fitter Plate Switch Housing 2 2. Select the configuration ( or ) which most closely matches your fan. Most ceiling fans have either a one-piece removable switch housing that connects to a fitter plate () or a permanent switch housing with a switch housing cap (). Switch Housing Cap Switch Housing Switch Housing Switch Housing Screw 3 3. Remove the three switch housing screws in order to remove the switch housing () or switch housing cap () from the existing fan. If applicable, remove any wire connectors that connect wires from the fan to the switch housing and/or disconnect the male and female plugs. Note: Save the three switch housing screws for later. Switch Housing Cap Switch Housing Screw 4. Use a screwdriver to push the plug button out of the switch housing () or switch housing cap (). Switch Housing Plug utton 4 Switch Housing Cap Plug utton 4 Turn of the Century TM

5 SSEMLY INSTRUCTIONS - FN MOUNT Cage Screw Light Cage 5. Remove the four cage screws from the brackets inside the shade. Install the bulb in the socket. Then attach the light cage to the shade using the four cage screws. Repeat for each shade. ulb racket 5 Shade Hex Nut Lock Washer Hex Nut Lock Washer 6 6. Remove the hex nut and lock washer from the threaded rod at the top of the light kit fitter. Then, insert the wires and threaded rod from the light kit fitter through the center hole in the switch housing () or the switch housing cap (). Secure the switch housing () or switch housing cap () to the light kit fitter using the lock washer and hex nut from the hardware bag. 7. Use the wire connectors to connect the wires from the light kit fitter to the wires in the switch housing ( or ). White to White lack to lack lack to lue 9-pin Connector White to White 7 If your fan has a fitter plate (), you may also need to connect the 9-pin connector from the fan to the 9-pin connector from the switch housing. Note: If your fan has two single-pin connectors instead of bare wires, it will be necessary to cut the wire very close to the single-pin connectors and strip 1/2 of insulation from the end of the two wires in order to connect the fan wires to the wires of the light kit. IMPORTNT: DO NOT cut the wires to the 9-pin connectors. 8. Using the three previously removed switch housing screws, re-attach the switch housing to the fitter plate () or the switch housing cap to the switch housing (). Switch Housing Screw 8 Switch Housing Screw 5 Turn of the Century TM

6 SSEMLY INSTRUCTIONS - FN MOUNT 9. ttach the pull chain extensions to the pull chains. 9 Pull Chain Extension 10. Restore the power at the main fuse or circuit breaker Turn of the Century TM

7 SSEMLY INSTRUCTIONS - CEILING MOUNT 1. Turn OFF the electrical power at the main fuse or circuit breaker. 1 ulb Cage Screw Light Cage 2 2. Remove the four cage screws from the small brackets inside the shade. Install the bulb in the socket. Then attach the light cage to the shade using the four cage screws. Repeat for each shade. Shade IP Rod Coupling 3. Remove the hex nut and lock washer from the IP rod. Then, feed the wires through the coupling and IP rod. Then, screw the coupling onto the threaded rod on top of the light kit fitter. 3 Lock Washer Hex Nut Canopy 4. Feed the wires through the downrod and canopy. Secure the downrod and canopy to the IP rod by reinstalling the lock washer and hex nut. Downrod 4 7 Turn of the Century TM

8 SSEMLY INSTRUCTIONS - CEILING MOUNT Outlet ox 5. ttach the mounting bracket to the outlet box (not included) using the screws and washers provided with the outlet box. Mounting racket Cap Nut racket Screw 5 Canopy OUTLET OX racket Screw Cap Nut 6 6. Remove the two cap nuts from the bracket screws. Lift the fixture until the end bracket screws extend through the holes in the canopy. Screw the cap nuts onto the bracket screws to secure the light kit to the outlet box. 7. ttach the pull chain extensions to the pull chains. 7 Pull Chain Extension 8. Restore the power at the main fuse or circuit breaker. ssembly is complete. 8 8 Turn of the Century TM

9 TROULESHOOTING If you have difficulty operating your new light kit, or have difficulty with installation, please contact Customer Service : , 9 a.m.- 5 p.m. Central time. WRNING: Ensure the power is turned off to the ceiling fan and light kit before performing any maintenance. PROLEM Fixture does not light up. SUGGESTED REMEDY 1. Turn on wall switch, and check fuses or circuit breakers. 2. Check wire connections from fan to light kit, located in the switch housing of the ceiling fan. 3. Lower the canopy on the fan. Ensure the blue fan wire (light power) is connected to a black (hot/live) household supply wire. Re-install the canopy. WRRNTY 5-YER LIMITED WRRNTY To obtain service, please contact the Service Department: , 9 a.m.- 5 p.m. Central time. Model Name: Ceiling Fan Light Kit Model No: ronze (SKU: ) The manufacturer warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The manufacturer will, at its option, repair, replace or refund the purchase price to the consumer. ll costs of installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specifically excludes liability for direct, incidental or consequential damages. s some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights and you may also have other rights which may vary from state to state. 9 TM Turn of the Century