INSTRUCTION MANUAL. PLASTIC MENDER mod. ITA

Size: px

Start display at page:

Download "INSTRUCTION MANUAL. PLASTIC MENDER mod. ITA"

Jeremy Randall
6 years ago
Views:

1 PRO F ES S I O N A L TE A M SRL INSTRUCTION MANUAL PLASTIC MENDER mod. ITA Document protected by copyright. Total or partial reproduction is forbidden. via Lazio, Pesaro Italy tel fax info@monaldi.com

INDEX 1 RAEE regulations 2 General Safety Precautions 3 PLASTIC MENDER components 4 Technical specifications 5 Safety and handling 6 How to operate 7 Accessories and consumables 1 RAEE

recycling of electrical and electronic equipment.

2 INDEX 1 RAEE regulations 2 General Safety Precautions 3 PLASTIC MENDER components 4 Technical specifications 5 Safety and handling 6 How to operate 7 Accessories and consumables 1 RAEE Regulations The symbol on the product or on its packaging indicates that this product should not be treated as household waste, but it must be handed in a collection point for the recycling of electrical and electronic equipment. By disposing of this product appropriately you will help prevent potential negative consequences that could result from improper disposal of the product. For more detailed information about recycling of this product, please contact the municipal office, the local waste disposal service or the shop where you purchased the product.

3 2. GENERAL SAFETY PRECAUTIONS WELDING AND CUTTING CAN BE HARMFUL TO YOURSELF AND OTHERS The user must therefore be educated against the hazards, summarized below, deriving from welding operations. ELECTRIC SHOCK - May be fatal Install and earth the welding machine according to the regulations. Do not touch live electrical parts or electrodes with bare skin, gloves or wet clothing. Make sure your working position is safe. Make sure the circuit breaker line has been dimensioned according to the power consumption of the equipment. This switch should intervene in emergency situations. Inspect the power cord frequently to check its integrity. FUMES AND GASES - May be hazardous to health Keep the nose, mouth and eyes away from smoke and noxious fumes. Work in the presence of adequate ventilation. RISK OF FIRE AND BURNS Staples heated can become very hot and burn the skin; you should therefore make sure there are no flammable materials in the area, and wear appropriate protective clothing such as gloves and gowns. NOISE Do not operate near pressure vessels or in the presence of dust, gases or fumes 3. PLASTIC MENDER components CASE TOOL CONTROL BOARD HANDLE FOR STAPLES WITH ELECTRIC WIRE STAPLES KIT MANUAL OF INSTRUCTIONS

4 4 SPECIFICATIONS Denomination : PLASTIC MENDER MOD. ITA Code : Voltage : 1 x 230Vac, 50/60 Hz Energy consumption : max 5 Watt Dimensions : 80x100x100h mm Weight : 1,1 kg IMPORTANT: appearance and specifications of the machine can change without notice by the manufacturer. ATTENTION!!!! There is no guarantee for breakage or damage to the parts repaired with this product. 5. SAFETY AND HANDLING Strict adherence to this user manual is reccommended for your safety ATTENTION Once the tip is positioned on the handle and the switch is turned on, the tip temperature will be between 100 and 200 C. If touched by mistake, it can cause burns, blindness or fires. Wear heat resistant gloves while working Before placing the tip, make sure that the ends of the handle are cold Do not touch the staple with bare hands when it is placed in position inside the locking holes Do not use the tool near combustible material Do not allow unauthorized personnel to use the equipment Do not use with wet hands When you finish working, turn off the switch and make sure that the end of the handle is completely cool before storing it in its case. The repair of plastic objects occurs by dissolution of the same: be careful of any molten droplets. OBSERVE THE FOLLOWING RULES TO AVOID INJURY OR DAMAGE This product is designed for the repair of plastic parts. Do not use it for purposes other than those for which it was designed. The tool should be used with staples authorized by the manufacturer. Do not disassemble Do not use in wet places Do not put the tool in water When switched off, do not pull on the cord

5 6. HOW TO OPERATE 1. Connect the device to a normal power outlet (220 V). 2. Adjust the temperature control knob on: - Low for thin plastic (bumpers, etc.) - Medium for plastic parts with a thickness of 5 mm (projectors, etc.) - High for thick and hard plastic parts 3. Turn on the main switch. 4. Choose the correct staple for repair and insert it in the tips. 5. Prepare the plastic parts for the repair matching the ends. 6. Heat the staple by holding for 10 seconds the red switch on the handle 7. When the clip is properly inserted in the plastic and wedged into place, turn it Release the button and hold the clip on the repair until it locks (it does not move). 9. Slowly remove the tool, leaving the head of the staple into place. WARNING BEWARE OF THE FRAGMENTS. WEAR SAFETY GLASSES WHEN CUTTING 11. Cut the protruding ends of the staple. 12. Use a sander if you need to remove the remaining ends of the staple.

6 7. ACCESSORIES AND CUNSUMABLES The "PLASTIC MENDER" comes with the following consumables supplied, which can be re-ordered from your local dealer: n 25 pcs cod n 25 pcs cod n 25 pcs cod n 25 pcs cod

7 DICHIARAZIONE DI CONFORMITA il fabbricante: MONALDI PROFESSIONAL TEAM S.r.l. Via Lazio, PESARO (PU) - ITALIA dichiara sotto la propria responsabilità che la macchina: KIT RIPARAZIONE PLASTICHE MATRICOLA : ANNO DI COSTRUZIONE : è conforme alle Direttive Comunitarie inerenti: COMPATIBILITA' ELETTROMAGNETICA 2004/108/CE MATERIALE ELETTRICO DESTINATO AD ESSERE ADOPERATO ENTRO TALUNI LIMITI DI TENSIONE 2006/95/CE oltre che alla norma 2002/95/CE (RoHS9 e per quanto applicabili alle norme armonizzate: EN :2007 EN :2007 EN :2006 EN :2006 EN :1999 EN :1999 EN /A1:2004 Pesaro lì MONALDI Professional team S.r.l. L' Amministratore Gambini Davide

USER S MANUAL. Rectifier 1 10 A/10 48 V for Kliar Line Art

USER S MANUAL. Rectifier 1 10 A/10 48 V for Kliar Line Art USER S MANUAL Rectifier 1 10 A/10 48 V for Kliar Line Art. 3004052 Dichiarazione CE di Conformità CE Conformity Declaration TIPO DELLA MACCHINA: RADDRIZZATORE 1 PRODUCT TYPE: RECTIFIER 1 Modello/ Model