Electric Griddle. Owner s Manual

Transcription

1 Electric Griddle Owner s Manual Models T, T, T, 0T, T, TC, TC, TC, 0TC, TC, S, S, S, 0S, S, SC, SC, SC, 0SC, SC This manual includes material related to installation, use, cleaning, and care. Exploded view[s], as well as any available parts list[s] and wiring diagram[s] pertaining to the unit[s] covered by this manual are also included. This manual must be read and understood by all persons using or installing this appliance. Contact your Lang dealer if you have any questions concerning installation, use, or maintenance of this equipment. DO NOT DISCARD THIS MANUAL. T M-Z Rev. C 0.0

2 LIMITED EQUIPMENT WARRANTY Star Manufacturing [as well as its subsidiaries] warranties new products to be free from defects in material and/or workmanship for a period of one [] year from the date of original installation, except as noted below. Defects that occur as a result of normal use, within the time period and limitations defined in this warranty, will at Star s discretion have the parts replaced or repaired by Star or a Star-authorized service agency. THIS WARRANTY IS SUBJECT TO ALL LISTED CONDITIONS. Repairs performed under this warranty are to be performed by a Starauthorized service agency. Star will not be responsible for charges incurred or service performed by non-authorized repair agencies. In all cases, the nearest Star-authorized service agency must be used. Star will be responsible for normal labor charges incurred in the repair or replacement of a warrantied product within 0 miles (0. km) of an authorized service agency. Time and expense charges for anything beyond that distance will be the responsibility of the owner. All labor will need to be performed during regular service hours. Any overtime premium will be charged to the owner. For all shipments outside the U.S.A. and Canada, please see the International Warranty for specific details. It is the responsibility of the owner to inspect and report any shipping damage claims, hidden or otherwise, promptly following delivery. No mileage or travel charges will be honored on any equipment that is deemed portable. In general, equipment with a cord and plug weighing less than 0 lb. (. kg) is considered portable and should be taken or shipped to the closest authorized service agency, transportation prepaid. PORTABLE EQUIPMENT EXAMPLES LL fryer JR popcorn machine MC and MCP hot food NCPW and NCPW nacho merchandisers merchandisers QCS, QCS, and RCS toasters nacho cheese warmers except PD-A pretzel merchandisers WLA-series models condiment dispensers except specialty food warmers except HPD- and SPD-series models 0R, RW, and WSA models all pop-up toasters all butter dispensers all pastry display cabinets all nacho chip merchandisers all heat lamps all accessories CONTACT Should you require any assistance regarding the operation or maintenance of any Star equipment; write, phone, fax or our service department. In all correspondence mention the model number and the serial number of your unit, as well as the voltage or type of gas you are using. Business hours are :00 a.m. to :0 p.m. Central Standard Time Telephone Star/Toasmaster..0 Lang.. Fax.. customerservice@star-mfg.com WARRANTY EXCLUSIONS THE FOLLOWING WILL NOT BE COVERED UNDER WARRANTY. Any product which has not been used, maintained, or installed in accordance with the directions published in the appropriate installation sheet and/or owner s manual, including incorrect gas or electrical connection. Star is not liable for any unit which has been mishandled, abused, misapplied, subjected to harsh chemicals, modified by unauthorized personnel, damaged by flood, fire, or other acts of nature [or God], or which have an altered or missing serial number. Installation, labor, and job checkouts, calibration of heat controls, air and gas burner/bypass/pilot adjustments, gas or electrical system checks, voltage and phase conversions, cleaning of equipment, or seasoning of griddle surface. Replacement of fuses or resetting of circuit breakers, safety controls, or reset buttons. Replacement of broken or damaged glass components, quartz heating elements, and light bulbs. Labor charges for all removable parts in gas charbroilers and hotplates, including but not limited to burners, grates, and radiants. Any labor charges incurred by delays, waiting time, or operating restrictions that hinder a service technician s ability to perform service. Replacement of items subject to normal wear or items that can easily be replaced during a daily cleaning routine, such as but not limited to knobs, bulbs, fuses, quartz heating elements, baskets, racks, and grease drawers. Any loss of business or profits. ADDITIONAL WARRANTIES PRODUCTS PARTS LABOR Lang Chef-Series convection ovens years years Lang Strato-Series convection ovens years years Lang convection oven doors lifetime years Lang LG and Star Ultra-Max griddles, charbroilers, and hotplates Star-Max fryers, griddles, charbroilers, and hotplates years years years years Jetstar popcorn poppers years years Staltek roller grill coatings chrome griddle surfaces [against peeling] lava rock charbroiler grates, burners, and burner shields original Star, Lang, or Toastmaster parts sold to repair Star, Lang, or Toastmaster equipment years years 0 days 0 days The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty. M-Z Rev A 0.0 i

3 TABLE OF CONTENTS Warranty i General Information Installation and Electrical Connection Wiring Diagrams Daily Operation Specifications Exploded View Parts List 0 M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

4 iii NOTES

5 SAFETY SYMBOLS These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance. THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL This unit has been tested for proper operation before leaving our plant to ensure delivery of your unit in perfect condition. However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation company who delivered the item to you and initiate your claim with that company. If this procedure is not followed, it may affect the warranty status of the unit. If damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within days. Please record the model number, serial number, voltage, and purchase date in the area below at the time of receipt.. Model Number Serial Number Voltage Purchase Date MAINTENANCE AND REPAIRS Contact your local authorized service agent for service or required maintenance. Please have the information in the above fields ready when you call to ensure a faster service. Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability. Due to periodic changes in designs, methods, procedures, policies, and regulations, the specifications contained in this document are subject to change without notice. Star reserves the right to change product specifications and design without notice. In regards to previously purchased equipment, such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements. While Star International Holdings Inc. exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifications. By using the information provided, the user assumes all risks in connection with such use. When performing maintenance, power to the unit should be unplugged or turned off. PLEASE REFER TO THE WARRANTY PAGE FOR SPECIFIC WARRANTY INFORMATION. AUTHORIZED SERVICE AGENT LISTING Reference the listing provided with the unit or for an updated listing go to the website or call customer service to find an agent. Business hours: :00 a.m. to :0 p.m. Central Standard Time Telephone: --0 Fax: -- customerservice@star-mfg.com Website: Please visit for digital versions of any documents associated with this unit. M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

6 GENERAL SAFETY INFORMATION This equipment is designed and sold for commercial use only, and is intended for use by personnel trained and experienced in its operation. This is not sold for consumer use in and around the home nor for use directly by the general public in food service locations. Before using your new equipment, read and understand all the instructions and labels associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation and safety before they use the unit. GENERAL INSTALLATION INFORMATION The unit is shipped fully assembled with the exception of the legs which will need to be installed during the unpacking process. It is shipped ready to hardwire to an electrical connection adequate for its voltage and amp draw. If improper electrical supply can be determined through troubleshooting, contact a qualified electrician prior to using the unit. Should you require assistance, contact your local authorized service agent for any service or required maintenance. Set the unit so that the rear is 0. inches ( mm) higher than the front using the adjustable feet. Make certain the griddle has at least the minimum clearance on the sides and back as called out on the nameplate of the unit. Before using the unit for the first time, make sure to clean the unit properly. Refer to the Daily Operation section for cleaning instructions. VENTILATION Make certain not to obstruct the flow of combustion and ventilation air. Provisions for adequate air supply must be furnished. The legs supplied with the unit must be installed. Make certain that air intake openings in the bottom of the appliance are not obstructed, as they are essential for proper combustion and operation of the appliance. It is essential that some form of exhaust hood be provided over the griddle to carry off fumes and gases. The unit should never be directly connected to a flue or stack. ELECTRICAL CONNECTION For your protection we recommend that a qualified electrician work on connecting this griddle. He should be familiar with electrical installations and all electric codes. Proper connections and power supply are essential for efficient performance. The external wiring should be in conduit or an approved type of flexible cable suitable for operation at the temperature indicated on the wiring diagram for your unit, and of a proper size to carry the load. The supply circuit should be properly fused and equipped with a means of disconnecting, as required by local electrical code. The body of the griddle should be grounded. Before making any electrical connection to this unit, check that the power supply is adequate for the voltage, amperage, and requirements stated on the nameplate. This unit will be shipped ready to hard wire. Make certain to disconnect the unit from the power source before installing or removing any parts. Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect equipment to power without proper ground connections. Improper grounding may result in personal injury or fatality.

7 WIRING Models may be wired for operation in the field for either -phase or -phase power supplies by making line connections at the junction box located at the rear of the unit as described on the phase diagram.,, 0, and models are recommended to be wired for -phase operation. 0 and models are supplied with two junction boxes. CONNECT/PLUG UNIT INTO DEDICATED AC LINE WITH APPROPRIATE AMPERAGE/VOLTAGE AS SPECIFIED ON THE NAMEPLATE OF THE UNIT. DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN THE UNIT OR THE TABLE/COUNTER IF THE UNIT IS ON THE TABLE/COUNTER. KEEP AWAY FROM RUNNING WATER. M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

8 0 0 0 WIRING DIAGRAM 0 V and 0 V version S S POSITION SWITCH POSITION SWITCH POSITION SWITCH S is the same with one additional section with the power connections being and. 0S griddles will use two connections with C being the same as one S and C being the same as one S. S griddles will use two connections with C and C each being the same as one S. SERVICE CONNECTIONS MODEL THREE PHASE SINGLE PHASE L L L L L,,,,,,,,,,,,,,,,,,,,, GRIDDLE ELEMENTS GRIDDLE PILOT LAMP CONTACTOR JUMPER TERMINAL BLOCK TEMP. CONTROL BOARD POSITION SWITCH TOGGLE SWITCH TRANSFORMER, CLASS 0 PROBE OVERTEMP STAT

9 0 0 WIRING DIAGRAM 0 V version S S V 0 V 0 YEL POSITION SWITCH BLU POSITION SWITCH POSITION SWITCH 0 S is the same with one additional section with the power connections being and. 0S griddles will use two connections with C being the same as one S and C being the same as one S. S griddles will use two connections with C and C each being the same as one S. SERVICE CONNECTIONS MODEL THREE PHASE SINGLE PHASE L L L L L,,,,,,,,,,,,,,,,,,,,, GRIDDLE ELEMENTS GRIDDLE PILOT LAMP CONTACTOR JUMPER TERMINAL BLOCK TEMP. CONTROL BOARD POSITION SWITCH TOGGLE SWITCH TRANSFORMER, CLASS 0 PROBE OVERTEMP STAT M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

10 WIRING DIAGRAM 0 V version T T T 0 0 V and 0 V version T T T T griddles will use two connections with C being the same as one T and C being the same as one T. T griddles will use two connections with C and C each being the same as one T. SERVICE CONNECTIONS MODEL THREE PHASE SINGLE PHASE L L L L L,,,,,,,,,,,,,,,,,,,,, GRIDDLE ELEMENTS GRIDDLE PILOT LAMP GRIDDLE THERMOSTAT TERMINAL BLOCK JUMPER [installed for 0 V, removed for 0 V]

11 DAILY OPERATION GRIDDLE CARE It takes very little time and effort to keep the griddle attractive and performing at top efficiency. If grease is permitted to accumulate, it forms a viscous residue and then carbonizes, making it extremely difficult to remove. To prevent this condition, the following suggestions for cleanliness should be followed. i. STANDARD STEEL SURFACE After each use, scrape the griddle with a scraper or flexible spatula to remove excess grease and food and maneuver it into the grease chute. If there is an accumulation of burned on grease and/or food, the griddle should be thoroughly scoured and reseasoned. Use pumice or griddle stone while the griddle is warm. Do not use steel wool because of the danger of steel slivers getting into the food. CHROME SURFACE After each use, scrape the griddle with a razor-sharp scraper. Following that, use a soft, damp cloth and a non-silicate, non-abrasive, non-chlorinated cleaner to wipe the surface clean. Follow this by wiping with a clean damp cloth with no cleaner. On chrome surfaces, never use pumice, griddle stones, abrasives, commercial liquid grill cleaner, and never strike the griddle surface with a sharp and/or hard instrument. ii. Daily use a clean cloth and a good non-abrasive cleaner to clean the stainless steel body of the griddle is recommended. Wipe the polished front with a soft cloth so not to scratch the finish. iii. At least once a day, remove the grease drawer and wash it using the same process as an ordinary cooking utensil. The drawer is removed by pulling forward until it is released from its track. SEASONING THE GRIDDLE HEATING SURFACE After the griddle has been thoroughly cleaned, it should be seasoned to prevent food from sticking. Before using and after each thorough scouring, season the griddle heating surface in the following manner. i. Turn the temperature control dials to 0 F ( C). ii. Using a clean cloth, not a spatula, spread a thin film of cooking oil over the griddle cooking surface. This film should remain on the hot griddle surface for half an hour. iii. Remove the excess oil and wipe clean. iv. Apply another film of cooking oil over the hot cooking area for another half hour and again remove excess oil and wipe clean. The griddle surface should now be ready for use. TEMPERATURE CONTROL SNAP-ACTION THERMOSTAT To power on the elements, turn the adjustment knob to the desired temperature. Turning the dial knob automatically maintains the selected heat range. There is one thermostat for every twelve [] inch (0 mm) wide section that operate independently. SELECTRONIC SOLID STATE To power on the elements, flip the switch corresponding to each section you wish to use to the ON position. Next, Turn the adjustment knob to the desired temperature [this system adjusts in increments of F ( C)]. COOKING Set the thermostat dial knob at the desired temperature. After a short pre-heating period, the thermostat will automatically maintain the selected temperature. IDLING During idle periods, to save on operating costs, lower the temperature setting of the thermostat to about 0 F ( C). It is not necessary to maintain cooking temperature during idle periods, as the griddle can quickly be reheated to the desired temperature. M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

12 SPECIFICATIONS T shown A. in. (0 mm) in. (0 mm) in. ( mm). in. (0 mm). in. ( mm). in. (0 mm) 0. in. ( mm) in. (0 mm) ELECTRICAL CONNECTION models. inches ( mm) from either side and models. inches ( mm) from right side 0 and models two [] connections, one. inches ( mm) from the right and one. inches ( mm) from the left. 0. in. ( mm) MODEL 0 HEIGHT in. ( mm) in. ( mm) in. ( mm) in. ( mm) in. ( mm). in. ( mm) WIDTH [A] in. (0 mm) in. ( mm) in. (. m) 0 in. (. m) in. (. m) DEPTH VOLTAGE kw Φ 0. in. ( mm) 0. in. ( mm) 0. in. ( mm) 0. in. ( mm) 0. in. ( mm) CLEARANCE Requires two electrical connections, noted as C for connection one [] and C as connection two []. These models are not CSA/cUL certified. 0 There must be at least one [] inch ( mm) of clearance between the sides and back of the unit and a wall.. 0 N/A. N/A. 00 N/A Φ L Φ L. 0.. C same as C same as C same as C same as Φ L APPROX. SHIP WEIGHT 0 lb. (. kg) lb. (. kg) 0 lb. (. kg) lb. (. kg) lb. ( kg) APPROX. WEIGHT INSTALLED 0 lb. (. kg) 0 lb. (. kg) 0 lb. (. kg) 0 lb. ( kg) 0 lb. (0. kg) 0 and models are not cul/csa certified

13 EXPLODED VIEW shown A B B 0 A A 0 0 M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

14 PARTS LIST Side references are from the operator s point-of-view from the front of the unit. All parts apply to chrome modelsalso except number, which has chrome or standard steel versions noted. Items labeled NP are not pictured. REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO A B T, S K-EZG- T, S K-EZG-0 T, S K-EZG- 0T, 0S K-EZG- T, S K-EZG- TC, SC TC, SC TC, SC 0TC, 0SC TC, SC T/S K-EZG- K-EZG- K-EZG- K-EZG- K-EZG- T/S T/S N-00-0T/0S T/S T/S T/S T/S N T/0S T/S T/S T/S T/S K-XL- 0T/0S T/S T/S T/S T/S K-XL- 0T/0S T/S T/S T/S T/S K-XL- 0T/0S T/S griddle plate main element perimeter element element pan plate element retainer element pan 0

15 REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO T/S K-EZG- T/S K-EZG- T/S K-EZG- body assembly 0T/0S K-EZG- T/S K-EZG-0 T/S G-Z T/S G-Z T/S G-Z rear panel 0T/0S G-Z T/S G-Z T E pole terminal block [element] S E pole terminal block [element] T E-000- pole terminal block [element] S E pole terminal block [element] T/S E-000- pole terminal block [element] E pole terminal block [element] 0T E-000- pole terminal block [element] 0S E pole terminal block [element] E pole terminal block [element] T E-000- pole terminal block [element] S E pole terminal block [element] T/S T/S T/S E pole terminal block [main power] 0T/0S T/S T/S T/S 0 T/S E-00-0 ground lug 0T/0S T/S ALL M-00- Lang badge ALL R-Z leg T/S T/S T/S G-Z grease drawer slide/cover 0T/0S T/S M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

16 REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO 0 T/S T/S T/S C- 0 0T/0S T/S T/S T/S T/S G-0 0T/0S T/S T/S G-Z. in. (0 mm) wide bottom panel T/S T/S 0T/0S T/S G-Z. in. (0 mm) wide bottom panel G-Z. in. ( mm) wide bottom panel G-Z. in. (0 mm) wide bottom panel G-Z0. in. ( mm) wide bottom panel G-Z. in. (0 mm) wide bottom panel G-Z in. ( mm) wide bottom panel G-Z. in. (0 mm) wide bottom panel G-Z 0 in. (,0 mm) wide bottom panel S E-00-0 pole terminal block S E-00-0 pole terminal block S E-00-0 pole terminal block 0S E-00-0 pole terminal block E-00-0 pole terminal block S E-00-0 pole terminal block S C-00-0 S C-00-0 S C S C-00-0 S C-00-0 S, S, S, 0S, S S #- screw grease drawer #0 screw E-00-0 transformer S S E S S contactor? K-00-0?

17 REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO ALL M-Z0 nameplate mount S S S E-00-W control board 0S S T/S T/S T/S C-00-0 tinnerman clip 0T/0S T/S S S A S E-00- control switch 0S S T T B T T-00-0 thermostat 0T T T/S T/S T/S C tinnerman speed nut 0T/0S T/S T K-Z00 T K-Z0 T K-Z0 0T K-Z0 T K-Z0 S K-Z front panel S K-Z S K-Z 0S K-Z S K-Z M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

18 REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO 0 T T T 0T T Y-0-0- S S S 0S S T T T R-Z 0T T S S S R-Z 0S S T T T K-EZG- 0T T S S S K-EZG- 0S S S S S E S S S, S, S, 0S, S S, S, S, 0S, S pilot/signal lamp die cast bezel knob assembly on/off switch plate I switch boot M-Z main power on/off label

19 REF NO MODEL PART NUMBER QTY DESCRIPTION PAGE NO S, S, S, 0S, S S Z main power switch guard S S E S S toggle switch M-Z Rev C Owner s Manual for Lang xx-series Electric Griddles

20 LANG MANUFACTURING Hobson Street Smithville, Tennessee Telephone Fax Printed in the U.S.A. M-Z Rev C 0.0 Specifications are subject to change without notice.