AITONS EQUIPMENT A COMPLETE LINE OF RESIDENTIAL AND COMMERCIAL EQUIPMENT FOR HEATING AND COOLING

Transcription

1 AITONS EQUIPMENT A COMPLETE LINE OF RESIDENTIAL AND COMMERCIAL EQUIPMENT FOR HEATING AND COOLING

2 TABLE OF CONTENTS This guide shows the full range of Comfort- Aire products for residential and commercial see our web site, or talk to your Comfort-Aire representative. Condensers Heat Pumps Air Handlers Cased and Uncased Coils... 5 Gas Furnaces Oil Furnaces... 7 Residential Package Units... 8 Ductless Mini-Splits Infrared & Convection Heaters Room Air Products Geothermal and Water Source All cooling products in this catalog are charged with or compatible with environmentally friendly R-410A except as noted in description. All product voltages are single phase except as noted in description. dimensions are subject to change and correction without notice or incurring obligations. Determining the application and suitability for use of any product is the responsibility of the installer. Additionally, the installer is responsible for verifying dimensional data on the actual product prior to beginning any installation preparations. Third party incentive and rebate programs have precise All products meet applicable regulations in effect on date granted for the life of a product. Therefore, it is the AITONS EQUIPMENT

3 SPLIT SYSTEM HEATING AND COOLING RSG16 Condensing Units 16 SEER Cooling 16 SEER Dimensions (in.) W x D x H RSG1624S1E 24,000 22¾ x 22¾ x 35½ RSG1630S1E 30,000 30¾ x 30¾ x 27½ RSG1636S1E 35,600 30¾ x 30¾ x 39½ RSG1642S1E 41,000 30¾ x 30¾ x 43½ RSG1648S1E 46,000 30¾ x 30¾ x 43½ RSG1660S1E 55,000 30¾ x 30¾ x 43½ AHRI matched to CMG/MMG/VMG coils ; also to HCG-**V HMG**X, HWCG**X Series air handlers. See for all matches. RSG Condensing Units 13 SEER Scroll compressor for efficiency and long life. Features full metal jacket to protect the coil, quiet operation, easy access control box and all aluminum micro-channel coils. PSC motor is permanently lubricated, needs no maintenance. SEER ratings/capacities vary based on air handler or coil used. 1 1 /2 to 5 Tons 208/230V-1-60 Micro-channel coils are efficient and highly corrosion resistant (1660 has copper tube/aluminum fin coil). Heavy duty scroll compressor adds efficiency and long life. Cabinet is steel with durable polyester urethane finish and heavy duty top grille assembly. Features full metal jacket, quiet operation, composite base pan and waterproof control box. Can be slab- or rooftop-mounted. 2 to 5 Tons 208/230V SEER Nom. W x D x H (in.) RSG1318S1E 18,000 22¾ x 22¾ x 23½ RSG1324S1E 24,000 22¾ x 22¾ x 23½ RSG1330S1E 30,000 22¾ x 22¾ x 27½ RSG1336S1E 36,000 22¾ x 22¾ x 27½ RSG1342S1E 42,000 30¾ x 30¾ x 27½ RSG1348S1E 48,000 30¾ x 30¾ x 27½ RSG1360S1E 60,000 30¾ x 30¾ x 31½ AHRI matched to CCG/MCG/VCG coils and most of our air handlers. See for all matches. 1 1 /2 to 5 Tons 208/230V-1-60 RSG Condensing Units 14 SEER Scroll compressor for efficiency and long life. Features full metal jacket to protect the coil, quiet operation, easy access control box and all aluminum micro-channel coils. PSC motor is permanently lubricated, needs no maintenance. SEER ratings/capacities vary based on air handler or coil used. 14 SEER Nom. W x D x H (in.) RSG1418S1E 18,000 30¾ x 30¾ x 31 RSG1424S1E 24,000 30¾ x 30¾ x 31 RSG1430S1E 30,000 30¾ x 30¾ x 35 RSG1436S1E 36,000 30¾ x 30¾ x 39 RSG1442S1E 42,000 30¾ x 30¾ x 43 RSG1448S1E 48,000 30¾ x 30¾ x 43 RSG1460S1E 60,000 30¾ x 30¾ x 43 AHRI matched to CCG/MCG/VCG coils; also, HMG**F, HMG**T, HMG**X and FMG**F and FMG**X air handlers. See for all matches SEER * Cooling Dimensions (in.) W x D x H RSG1318R1E 17,100 22¾ x 22¾ x 27½ RSG1324R1E 22,800 22¾ x 22¾ x 27½ RSG1330R1E 28,800 22¾ x 22¾ x 27½ RSG1336R1E 35,400 22¾ x 22¾ x 35½ AHRI matched to CCG/MCG/VCG coils, also HMG**F, HMG**T and FMG air handlers.; SEER ratings and capacities vary depending on air handler or coil used. Builders Series Condensing Units Built with rotary compressors and PSC motors for reliability. Features include metal jacket, micro-channel all-aluminum coil to resist corrosion. Top grille assembly for easy access to components. 208/230V /2 to 3 Tons 1

4 Compact size fits in tight spaces, great for apartment complexes. ARHI matched to Comfort-Aire coils and hydronic air handlers. Built with rotary compressor and durable painted cabinet. 208/230V /2 to 3 Tons CMA Horizontal Condenser 13 SEER Nom. Dimensions (in.) W x D x H CMA18SB-1 18, /16 x 27 5 /8 x 14 1 /4 CMA24SB-1 24, /16 x /16 x 14 CMA30SB-1 30, x 38 x 15 5 /8 CMA36SB-1 36, /16 x 46 1 /8 x / /2 to 5 Tons Dry R-22 Condensers Designed as a replacement for existing R-22 systems. Units come with dry nitrogen charge that s exhausted before charging with R-22. Features scroll compressor and full metal jacket. SEER ratings/ capacities vary depending on air handler or coil used. 208/230V SEER Nom. Dimensions (in.) W x D x H RSN1318S1E 18,000 22¾ x 22¾ x 23 RSN1324S1E 24,000 22¾ x 22¾ x 23 RSN1330S1E 30,000 22¾ x 22¾ x 27 RSN1336S1E 36,000 22¾ x 22¾ x 27 RSN1342S1E 42,000 30¾ x 30¾ x 31 RSN1348S1E 48,000 30¾ x 30¾ x 31 RSN1360S1E 60,000 30¾ x 30¾ x 31 HRG16 Heat Pumps 16 SEER Cooling* Heating* 16 SEER HSPF HRG1624S1E 24,000 24, HRG1636S1E 36,000 36, HRG1648S1E 48,000 46, HRG1660S1E 55,000 52, to 5 Tons 208/230V-1-60 * Capacities shown with HCG**V1E air handlers; capacities with vary slightly with other air handlers or coils. Copper tube/aluminum fin coil are designed for maximum heat transfer. Copeland scroll compressor has two stages of heating/cooling capacities. Cabinet is steel with durable poly urethane finish and heavy duty top grille assembly. metal jacket protects the coil. Composite base pan is corrosion resistant and control box is waterproof SEER Cooling* Heating* HSPF* HRG1318S1E 18,000 19, HRG1324S1E 23,000 24, HRG1330S1E 28,800 30, HRG1336S1E 34,800 36, HRG1342S1E 40,000 42, HRG1348S1E 47,500 47, HRG1360S1E 57,500 60, SEER Cooling** Heating** HSPF** HRG1418S1E 19,200 18, HRG1424S1E 23,400 24, HRG1430S1E 28,400 29, HRG1436S1E 34,800 33, HRG1442S1E 39,500 38, HRG1448S1E 45,500 44, HRG1460S1E 59,000 52, HRG13: Minimum SEER 13; HRG14: Minimum SEER 14 HRG Heat Pumps High efficiency heat pumps available in 13 and 14 SEER models. Built with scroll compressors for efficiency and reliability. Long life copper coils with aluminum fins optimize heat transfer. Time/temperature defrost. PSC motor is permanently lubricated. metal jacket is galvanized steel with polyester urethane coating for durability, corrosion resistance. 208/230V /2 to 5 Tons * Capacities shown with HMG**F air handlers; capacities will vary slightly with other air handlers or coils. **Capacities shown with HCG**V1E air handlers; capacities with vary slightly with other air handlers or coils. 2

5 1 1 /2 to 5 Tons Dry R-22 Heat Pumps Designed as replacements for existing R-22 systems, features scroll compressor for for durability. Time/temperature defrost offers a variety of settings. SEER ratings/capacities will vary slightly depending on air handler or coil used. 208/230V SEER Nom. Cool & Heat Dimensions (in.) W x D x H HRN1318S1E 18,000 30¾ x 30¾ x 27 HRN1324S1E 24,000 30¾ x 30¾ x 27 HRN1330S1E 30,000 30¾ x 30¾ x 39 HRN1336S1E 36,000 30¾ x 30¾ x 43 HRN1342S1E 42,000 30¾ x 30¾ x 39 HRN1348S1E 48,000 30¾ x 30¾ x 43 HRN1360S1E 60,000 30¾ x 30¾ x 43 HCG24V1E Cap. Tons Matched Condensers Matched Heat Pumps 1.5, 2.0 HCG30V1E 2.5 HCG36V1E 3.0 RSG1318S1E, RSG1324S1E RSG1418S1E, RSG1424S1E RSG1624 RSG1330S1E, RSG1430S1E RSG1630 RSG1336S1E, RSG1436S1E RSG1636 HRG1318S1E, HRG1324S1E RSG1418S1E, HRG1424S1E HRG1624 HRG1330S1E, HRG1430S1E HRG1336S1E, HRG1436S1E HRG1636 HCG42V1E 3.5 RSG1342S1E, RSG1442S1E HRG1342S1E, HRG1442S1E HCG48V1E 4.0 HCG60V1E 5.0 RSG1342S1E, RSG1442S1E RSG1348S1E, RSG1448S1E RSG1642, RSG1638 RSG1360S1E, RSG1460S1E RSG1660 RSG13- and HRG13- models rated at 13.5 to 14 SEER. RSG14- and HRG14- models rated at 14 to 15 SEER. RSG16- and HRG16- models rated at 16 SEER. HRG1342S1E, HRG1442S1E HRG1348S1E, HRG1448S1E HRG1648 HRG1360S1E, HRG1460S1E HRG /240V-1-60 HCG Variable Speed Air Handler ECM blower motor Multi- position - vertical). A-coil is coated for corrosion protection. Cabinet has polyester urecabinet is insulated. Optional plug-in electric heater kits are available in 5 to 30 kw. 1 1 /2 to 5 Tons FMG Wall Mount Air Handler Two models available: FMG--F1E with PSC blower motor and and FMG--X1E with ECM blower motor and TXV, rated up to 15 SEER (with Comfort-Aire matched units). y insulated cabinet, front and/or bottom return air. Offset hanging bracket included. Optional decorative louvered panel is available. 1 1 /2 to 3 Tons 208/230V-1-60 Cap. Tons Matched Condensers SEER Matched Heat Pumps FMG18--F1E 1.5 RSG1318S1E 13.0 HRG1318S1E FMG24--F1E 2.0 RSG1324S1E, RSG1324R1E 13.0 HRG1324S1E FMG30--F1E 2.5 RSG1330S1E, RSG1330R1E 13.0 HRG1330S1E FMG36--F1E 3.0 RSG1336S1E, RSG1336R1E 13.0 HRG1336S1E FMG18--X1E 1.5 RSG1418S1E 15.0 HRG1418S1E FMG24--X1E 2.0 RSG1424S1E 15.0 HRG1424S1E FMG30--X1E 2.5 RSG1430S1E 15.0 HRG1430S1E FMG36--X1E 3.0 RSG1436S1E 15.0 HRG1436S1E Dashes in the part numbers are for digits indicating factory installed heater kit, 05, 08, 10 kw; example: FMG1808FIE. All cooling products in this catalog are charged with or compatible with environmentally friendly R-410A except as noted in description

6 HMG Air Handlers Multi-position (upflow, downflow, horizontal or vertical) air handlers are available in three varieties. Each features optional plug-in electric heater kits available in 5 to 30 kw. Micro-channel A-coil for efficiency and corrosion resistance. Durable cabinet has polyester urethane finish, and blower cabinet is insulated. HMG**F1E Permanently lubricated PSC drive, multi-speed for application flexibility HMG**T1E PSC drive and TXV metering device for precise refrigerant control HMG**X1E TXV metering valve and fixed torque ECM blower motor with 16 airflow speeds each for heating and cooling that can be set in the field to match the application HMG Air Handler with PSC Drive Up to 14 SEER* Cap. Tons Matched Units Condensers Matched Units Heat Pumps HMG24--F1E 1.5, 2.0 RSG1318S1E, RSG1324S1E RSG1318R1E, RSG1324R1E HRG1318S1E, HRG1324S1E HRG1418S1F, HRG1424S1F HMG30--F1E 2.5 RSG1330S1E RSG1330R1E HRG1330S1E HRG1430S1F HMG36--F1E 3.0 RSG1336S1E HRG1336S1E HRG1436S1F HMG42--F1E 3.5 RSG1342S1E RSG1336R1E HRG1342S1E HRG1442S1F HMG48--F1E 4.0 RSG1348S1E HRG1348S1E HRG1448S1F HMG60--F1E 5.0 RSG1360S1E HRG1360S1E HRG1460S1F HMG Air Handler with TXV and PSC Drive Up to 14 SEER* Cap. Tons Matched Units Condensers Matched Units Heat Pumps HMG24--T1E 1.5, 2.0 RSG1318S1E, RSG1324S1E RSG1418S1E, RSG1424S1E HRG1324S1E HRG1418S1F, HRG1424S1F HMG30--T1E 2.5 RSG1330S1E RSG1430S1E HRG1330S1E HRG1430S1F HMG36--T1E 3.0 RSG1336S1E HRG1436S1F HMG42--T1E 3.5 RSG1342S1E RSG1442S1E HRG1342S1E HMG48--T1E 4.0 RSG1348S1E RSG1448S1E HRG1348S1E HRG1442S1F, HRG1448S1F 1 1 /2 to 5 Tons HMG60--T1E 5.0 RSG1360S1E RSG1460S1F HRG1360S1E HRG1448S1F, HRG1460S1F HMG Air Handler with TXV & Fixed Torque Blower Motor Up to 16 SEER* Cap. Tons Matched Units Condensers Matched Units Heat Pumps HMG24--X1E 1.5, 2.0 RSG1318S1E, RSG1324S1E RSG1418S1E, RSG1424S1E RSG1624S1E HRG1318S1E, HRG1324S1E HRG1418S1F, HRG1424S1F HMG30--X1E 2.5 RSG1330S1E RSG1430S1E RSG1630S1E HRG1330S1E HRG1430S1F HMG36--X1E 3.0 RSG1336S1E RSG1436S1E RSG1636S1E HRG1336S1E HRG1436S1F HMG42--X1E 3.5 RSG1342S1E RSG1442S1E RSG1642S1E HRG1342S1E HRG1442S1F HMG48--X1E 4.0 RSG1342S1E, RSG1348S1E RSG1448S1E RSG1648S1E HRG1342S1E, HRG1348S1E HRG1448S1F HMG60--X1E 5.0 RSG1360S1E RSG1460S1F HRG1360S1E HRG1460S1F *Depending on matched unit Dashes in the part numbers used to indicate factory installed heater kit, 05, 08, 10 kw; example: HMG2405FIE. s w/ PSC Motor Nom. Cap. () Cabinet Width (in.) Max. Aux. Heat kw HMB24AA1E 24,000 14¼ 10 HMB36AA1E 36,000 14¼ 15 HMB36AB1E 36,000 17½ 20 HMB48AC1E 48, HMB60AC1E 60, s with ECM Variable Speed Motor HMB36VA1E 36,000 14¼ 15 HMB48VB1E 48,000 17½ 20 HMB60VC1E 60, /2 to 5 Tons 208/240V-1-60 HMB Modular Air Handler Flexible option when space is an issue. Install with a cased coil for customized two-piece air handler. Multi-position design delivers installation flexibility. With 1/2" cabinet insulation for quiet operation. Optional plug-in heat kits, 5 to 20 kw. Minimum 13 SEER; actual SEER rating depends on coil matched with air handler. 4

7 Nom. Cooling Heating 3.5 GPM* Cap. Tons 120 o F EWT 180 o F EWT HWCG24X0A ,600 59,300 HWCG30X0A ,700 65,500 HWCG42X0A ,800 86,300 HWCG48X0A , ,300 HWCG60X0A , ,400 HWCG24T0A ,600 48,400 HWCG36T0A ,800 67,300 HWCG48T0A ,900 98,000 HWCG60T0A , ,200 *At high speed setting Nom. Cooling Cap. Tons Heating Cap AHG24-0E ,000-30, AHG30-0E ,000-39, AHG36-0E ,000-50, AHG48-0E ,000-67, AHG60-0E ,000-80, AHGV24-0E , , AHGV36-0E ,500 1, ,000 1,200 AHGV48-0E ,000 14, ,000 1,600 AHGV60-0E ,000 1,800 Hydronic Air Handlers for Boiler Loops Multi-position, freeze protection in both cooling and heating. Slide-out blower assembly, blower time delay and low voltage terminal strip. Noncorrosive drain pans. HWCGxxX0A Series ECM constant torque blower motor. HWCGxxT0A Series Reliable PSC blower motor. 115V ½ to 5 Tons Hydronic Air Handlers Ideal replacement units are multiposition, with freeze protection in both cooling and heating. Slide-out blower assembly, blower time delay and low voltage terminal strip. Non-corrosive drain pans. TXV for R-410A built into unit. AHG Series Reliable PSC blower motor. AHGV Series ECM blower motor for constant CFM over a wide range of external static pressures. 115V ½ to 5 Tons For use with split system air conditioners and heat pumps. 5 Right or left hand connections offer installation flexibility. Drain pan is non-corrosive. Cased coil cabinet is insulated for quiet operation. Coils feature rifled copper tubing with aluminum fins. With TXV. Micro-channel coils for split system installations AHRI-matched to Comfort- Aire 16 SEER condenser and micro-channel heat pumps. Coils feature micro-channel all aluminum coils, with piston and flowrator for precise refrigerant control. Cased coils feature insulated cabinets and split front panel for easy service access. CMG Series Uncased coil MMG Series Multi-position cased coil VMG Series Upflow/downflow cased coil (requires drain pan kit for horizontal installation All in 2 to 5 ton capacities. 13 and 14 SEER coils for split system installations CCG Series Uncased coils VCG Series Cased coils, upflow/ counterflow MCG Series Cased, multi-position All in 1 1 /2 to 5 ton capacities. Minimum 13 SEER with RSG13 & HRG13 units, 14 SEER with RSG14 & HRG14 units; see ARHIdirectory.org for matches. 5

8 95% Two Stage Gas Furnace ECM variable speed blower motor provides even temperatures and improved indoor air quality. Two stage design operates at low speed most of the time to save energy, automatically ramps up to second stage when there s demand. All units A/C ready. Upflow model only. Hi Fire Input Lo Fire Input AFUE GUH95T060B4* 60,000 39, % GUH95T080C5* 80,000 52, % GUH95T100C5* 100,000 65, % GUH95T120D5* 120,000 78, % *Energy Star certified 115V % Single Stage Gas Furnace with ECM Constant Torque Blower Motor ECM blower motor provides even temperatures and improved air delivery. Compact size is ideal for replacements and new construction. On-board diagnostics, quiet operation, and limited lifetime warranty on heat exchangers. All units A/C ready. Upflow model only. *Energy Star certified 115V-1-60 Input AFUE GUH95C038A4* 38, % GUH95C054B4* 54, % GUH95T072C4* 72, % GUH95C090C4* 90, % GUH95C108D4* 108, % GUH95C120D4* 120, % Upflow/Horiz Input Down Input GUH95A038B4 38,000 GDD95A054B4 54,000 GUH95A054B4 54,000 GDD95A072C5 72,000 GUH95A072C5 72,000 GDD95A090C5 90,000 GUH95A090C5 90,000 GDD95A118D5 118,000 GUH95A108D5 108,000 GUH95A120D5 120, % AFUE A = 14 1 /2" cabinet width B = 17 1 /2" cabinet width C = 21" cabinet width D = 24 1 /2" cabinet width Last digit = nom. tons cooling 95% Single Stage Gas Furnace Efficient and reliable heat exchangers, hot surface igniter, integrated furnace control with on-board diagnostics, and multispeed blower motor. PSC blower motor. Low profile cabinet is ideal for replacements. All units are A/C ready. 115V-1-60 Down/Horiz = Downflow/Horizontal Configuration Upflow/Horiz Input Down Input GUH92A038A3 38,000 GDD92A054B4 54,000 GUH92A054B4 54,000 GDD92A072B4 72,000 GUH92A072B4 72,000 GDD92A090C5 90,000 GUH92A072C5 72,000 GDD92A120D5 120,000 GUH92A090C5 90,000 GUH92A108D5 108,000 GUH92A120D5 120,000 A = 14 1 /2" cabinet width B = 17 1 /2" cabinet width C = 21" cabinet width D = 24 1 /2" cabinet width Last digit = nom. tons cooling 92% Single Stage Gas Furnace Features two heat exchangers, hot surface igniter for reliability, integrated furnace control with on-board diagnostics, and easy-to-change filter. Three speed PSC blower motor has no belts or pulleys to wear out. Low profile cabinet is ideal for replacements. 92.1% AFUE 115V-1-60 Down/Horiz = Downflow/Horizontal Configuration All GUH/GDD gas furnaces can be converted from natural gas to LP No. LP Kits for all GUH/GDD Furnaces LP Kit for USA, 0-10,000 ft LP Kit for Canada, ft 6

9 80% Gas Furnace Our non-condensing gas furnace features hot surface igniter, in-shot burner and tubular heat exchanger. Multi-speed direct drive blower delivers warm air quietly. Low profile cabinet fits in even tight spaces. Integrated control board includes diagnostic lights. LP conversion kits are available. 80% AFUE 115V-1-60 Upflow/Horiz. Input Downflow Input GUH80A045A3 45,000 GDD80A054A3 54,000 GUH80A054A3 54,000 GDD80A072B4 72,000 GUH80A072B4 72,000 GDD80A090B4 90,000 GUH80A072C5 72,000 GDD80A108C5 108,000 GUH80A090B4 90,000 GDD80A126D5 126,000 GUH80A090C5 90,000 A = 14 1 /2" cabinet width GUH80A108C5 108,000 B = 17 1 /2" cabinet width GUH80A126D5 126,000 C = 21" cabinet width D = 24 1 /2" cabinet width Last digit = nominal tons cooling Input Blower Speed/ CFM Blower Motor HP MGD60-E3B 60,000 3 Speed, /3 MGD70-E3B 70,000 3 Speed, /3 MGD77-E3B 77,000 3 Speed, /3 MGD90-E3B 90,000 3 Speed, /3 MGD60-E5B 60,000 4 Speed, /4 MGD70-E5B 70,000 4 Speed, /4 MGD77-E5B 77,000 4 Speed, /4 MGD90-E5B 90,000 4 Speed, /4 Gas Furnaces for Manufactured Homes Specifically designed for installation in manufactured housing: sealed combustion system is safe and efficient. Cabinet is fully insulated for quiet operation. Features solid state integrated control board, combustion blower, hot surface ignition system and attractive appearance. Complete line of accessories available. 115V % AFUE Highboy Output AFUE OUFB75-D , % OUFB95-D , % OUFB125-D , % Down/Horiz Output AFUE ODFB95-D , % ODRB95-D , % ODFB125-D , % Lowboy Output AFUE OLFB95-D , % OLRB95-D , % OLFB125-D , % OLRB125-D , % OLFB, OUFB and ODFB=front flue; OLRB and ODRB=rear flue Shipped with high fire nozzle installed; nozzle change adjusts firing rate. Highboy and lowboy models with Beckett AFG oil burner, new advanced burner control, multi-speed direct drive blower, and foil-faced insulation. 115V-1-60 Oil Furnaces up to 84% AFUE Industrial Oil Furnace 225, ,000 Large capacity makes these ideal for churches, schools and commercial buildings. Can be installed either vertically or horizontally. Twin blowers are mounted on rails to be serviced from either side. Rated at 81% steady state efficiency. Firing Rate GPH LG14-225/275B LG14-350/450B Oil Burner LG14-225/275B40 A501-1 LG14-350/450B60 A502-1 Output 225, , , ,000 Nozzle Size o B o B o B o B Oil burners must be ordered separately. Motor 1.5 HP 2.0 HP All models 230V

10 Package Gas Heat/ Electric Cooling Cooling Heat Input Cooling Heat Input TGRG24451E 23,600 45,000 TGRG36721E 35,800 72,000 TGRG24721E 23,600 72,000 TGRG36961E 35,800 96,000 TGRG30451E 29,000 45,000 TGRG42961E 42,000 96,000 TGRG30721E 29,000 72,000 TGRG48961E 46,000 96,000 TGRG601201E 57, , / Micro-channel coils optimize heat transfer; features one piece top for water management and scroll compressor for efficiency. Self-contained units require only ductwork and a thermostat. Convertible air delivery horizontal or downflow. Can be rooftop- or slab-mounted. 13 SEER, 80% AFUE Compact cabinet has full perimeter base rails and durable poly urethane finish. Mesh hail guard protects the coil. Features include compact footprint, durable cabinet with poly urethane finish, permanently lubricated PSC motor, mesh hail guard. 208/ SEER, 7.7 HSPF Residential Package Units Cooling Only All Comfort-Aire ductless mini-splits are built with efficient inverter technology offering these benefits: t Precise temperature control with reduced temp fluctuations for enhanced comfort t Reduced on-off cycling for extended component life Cooling Heat Pump DUCTLESS MINI-SPLITS Cooling 2 to 5 Tons Heating TARG24001E 23,800 TPRG24001E 24,000 24,000 TARG30001E 28,600 TPRG30001E 28,400 28,400 TARG36001E 36,000 TPRG36001E 34,600 34,600 TARG42001E 40,500 TPRG42001E 40,500 40,500 TARG48001E 47,000 TPRG48001E 46,000 44,500 TARG60001E 56,000 TPRG60001E 56,000 54,500 Dedicated horizontal flow in cooling only or heat pump models. Ideal wherever a self-contained unit is needed. Mount on slab, or side discharge can be field modified for rooftop applications. Optional field-installed electric heater and other accessories are available. t Exceptionally quiet operation t Super efficient matches compressor speed to load demand, saving estimated 40% or more on energy consumption compared to non-inverter mini-splits t Extra heating capacity even at low ambient temps Includes wireless remote Ductless Mini-Splits Single Zone 15 SEER Available in cooling only and heat pump models. Efficient, economical comfort with cooling, heating (heat pump models), fan only, sleep and dehumidifications modes. Built with 24-hour timer, superior filtration and auto temperature Specifications (), 15 SEER DVC09SD-0 9,000 ; cooling only, 115V, EER 9.0 DVC12SD-0 12,000 ; cooling only, 115V, EER 9.0 DVC18SD-1 18,000 ; cooling only, 208/230V, EER 9.0 DVC24SD-1 22,000 ; cooling only, 208/230V, EER 9.0 DVH09SD-0 9,000 cool/9,000 heat; HP, EER 9.0, HSPF 8.2 DVH12SD-0 12,000 cool/12,000 heat; HP, EER 9.0, HSPF 8.2 DVH18SD-1 18,000 cool/18,000 heat, HP, EER 9.0, HSPF 8.2 DVH24SD-1 22,000 cool/22,000 heat, HP, EER 9.0, HSPF 8.2 compensation. Power Supply: 9K and 12K: 115V; 18K and 24K: 208/230V 8

11 Ductless Mini-Split Heat Pumps up to 23.5 SEER! Super efficient heat pump mini-splits with variable speed compressors save up to 40% in energy consumption over standard models. With built-in low ambient operation. Includes wireless remote Specifications VMH09SD-0 9,000 cool/11,500 heat BTU, 23.5 SEER, 115V VMH12SD-0 11,500 cool/12,000 heat BTU, 22.0 SEER, 115V VMH09SD-1* 9,000 cool/11,500 heat BTU, 23.5 SEER, 208/230V VMH12SD-1* 11,500 cool/12,000 heat BTU, 22.0 SEER, 208/230V VMH18SD-1* 17,500 cool/18,000 heat BTU, 21.0 SEER, 208/230V VMH24SD-1* 23,000 cool/24,000 heat BTU, 19.0 SEER, 208/230V VMH30SC-1 30,000 cool/30,000 heat BTU, 16.0 SEER, 208/230V VMH36SC-1 36,000 cool/36,000 heat BTU, 14.5 SEER, 208/230V *VMH09, -12, -18 and -24 models are Energy Star compliant Multi-Zone Mini-Split Heat Pumps Inverter Technology Cool and heat one to five separate rooms or areas, depending on the capacity of the outdoor unit. Each zone has an independently controlled air handler with remote; ceiling cassettes and ducted units also have a wired wall thermostat. Built with enhanced filtration, quiet operation, multiple Outdoor Unit modes, low ambient cooling and Follow function. Mix n match indoor units May be sized up to 150% of outdoor unit capacity, but may not provide full capacity for all indoor units. Total capacity of all indoor units should not be less than 50% of the outdoor unit s capacity. Floor & Wall Console High Wall Mount Floor & Ceiling Console Ducted Unit Ceiling Cassette 208/ SEER 16.0 Outdoor Unit System Capacity Cooling/Heating A-VFH18DA-1 18,000 cool, 19,000 heat, HSPF 8.2 A-VFH24TA-1 26,000 cool, 29,000 heat, HSPF 8.2 A-VFH30QA-1 29,000 cool, 30,400 heat, HSPF 8.2 A-VFH36QA-1 34,000 cool, 35,800 heat, HSPF 8.2 A-VFH42PA-1 40,000 cool, 44,500 heat, HSPF 8.2 High Wall Mount Indoor Capacity per unit B-VFH09MA-1 9,000 cool, 9,800 heat, 430 max. CFM B-VFH12MA-1 12,000 cool, 13,000 heat, 453 max. CFM B-VFH18MA-1 18,000 cool, 19,000 heat, 588 max. CFM Indoor Ceiling Cassette B-VFH12CA-1 B-VFH18CA-1 B-VFH24CA-1 Front Panels Capacity per unit 12,000 cool, 13,000 heat, 353 max. CFM 14,400 cool, 16,000 heat, 353 max. CFM 22,800 cool, 27,400 heat, 694 max. CFM C-VFH1218CA 12K & 18K; C-VFH24CA 24K Ducted Unit Capacity per unit Mix & match indoor units up to maximum capacity 8,500 cool, of outdoor 9,500 heat, condenser! 265 max. CFM B-VFH09DA-1 B-VFH12DA-1 B-VFH18DA-1 B-VFH21DA-1 B-VFH24DA-1 Floor/Wall Console Indoor B-VFH09FA-1 B-VFH12FA-1 B-VFH18FA-1 Floor/Ceiling Indoor Unit B-VFH09A-1 B-VFH12A-1 B-VFH18A-1 B-VFH24A-1 11,900 cool, 13,100 heat, 324 max. CFM 15,300 cool, 18,700 heat, 412 max. CFM 20,400 cool, 22,600 heat, 588 max. CFM 22,800 cool, 27,400 heat, 588 max. CFM Capacity per unit 9,000 cool, 9,500 heat, 383 max. CFM 12,000 cool, 13,000 heat, 441 max. CFM 18,000 cool, 19,000 heat, 494 max. CFM Capacity per unit 8,500 cool, 9,500 heat, 383 max. CFM 11,900 cool, 13,100 heat, 383 max. CFM 17,000 cool, 18,700 heat, 559 max. CFM 22,800 cool, 27,400 heat, 736 max. CFM 9

12 INFRARED & CONVECTION HEATERS Infrared Outdoor Heaters 1500W, 3000W, 6000W FEATURES IR15S 1 Emitter IR30S 2 Emitters IR60S 3 Emitters Power / / Power Supply Wall outlet* Hard wired** Hard wired** Watts / Amps 1500W / 12.5A 3000W / 12.5A 6000W / 25A Heating Area 8' x 8' 10' x 12' 12' x 14' Mounting Height 7' to 8' 8 1 /2' to 10' 10' to 15' Power Cable 15' with wall plug 6' per emitter 6' per emitter Height x Depth 3 13 /16" x 3" 3 13 /16" x 4 13 /16" 3 13 /16" x 4 13 /16" Heaters can be mounted on the wall or ceiling, mounting brackets are included with heater. Add comfort on cool days ideal for patio, balcony, terrace, porch or other outdoor space. Heater emits a warm ambient glow that warms people and objects, not the air surrounding them. Instant ON with silent, odorless operation. Constructed of durable anodized aircraft aluminum and IP65 rated for use in wet environments. Free-Standing Infrared Outdoor Heater 1500W IRPH15SS Features Material Stainless steel, anodized 6061 aircraft aluminum Watts/Amps 1500W / 12.5A Power 120V AC (grounded outlet) Power Cord 15 feet long Dimensions Heater section: 20" W x 24" D Base: 18" in diameter Assembled height: 82" IP65 rated for wet environments, use in all seasons. Advanced medium wave infrared technology warms people and objects within a 64 square foot area, without heating the air. Radiated heat is unaffected by wind for efficient operation. Ideal for deck, patio or other outdoor area, heater plugs into a standard 120V outlet. Lamp is mounted on a strong mast with a heavy duty base for stability. Safety features include tip-over protection. Glass Panel Indoor Convection Heater 1500W Advanced X-grid convection heating delivers quiet, comfortable warmth. A built-in thermostat maintains the set temperature, with low level radiant heating providing even heat distribution. Safety features include thermal cut-out switch to prevent overheating and tip-over switch. Can be operated using unit s control panel or the handy wireless remote. With 24 hour ON/OFF timer for convenience. IRGPH15B Features & Dimensions Power Supply 120V-1-60 Display LED (temperature and mode) Width 32 5 /16 (820 mm) Heater Depth 32 5 /16 (820 mm) Height /16 (450 mm) Heater with caster kit Depth 9 15 /16 (250 mm) Height 20 1 /8 (510 mm) Heater can be wall-mounted (brackets included) or used with caster kit for room-to-room portability (also included). Not for use in wet environments. 10

13 ROOM AIR PRODUCTS Nom. Cooling BTU Remote Power RG-51 5,000 No 115V RADS-51 5,000 Yes 115V RAD-61 6,000 Yes 115V RADS-61 6,000 Yes 115V RAD-81 8,000 Yes 115V RADS-81 8,000 Yes 115V RADS ,000 Yes 115V RAD ,000 Yes 115V RADS ,000 Yes 115V RADS ,700/12,000 Yes 208/230V RADS ,000 Yes 115V RADS ,100/18,500 Yes 208/230V RADS ,700/22,000 Yes 208/230V RADS ,700/25,000 Yes 208/230V RAD ,000/28,500 Yes 208/230V Air Conditioners 5,000 to 28,000 All units come with a window mounting system. Galvanized steel, painted cabinets are lightweight and finished in attractive neutral color. All have electronic controls and wireless remote, timer and energy saver mode except RG-51. Slide-out filter is washable. ENERGY STAR CERTIFIED MODELS: See productfinder/ for a complete listing of Comfort-Aire Energy Star certified room air conditioners. Appearance may vary slightly from images shown. RG-51 For supplemental electric heat only. Air Conditioning with Electric Heat Features 3-speed fan, 24-hour on/off timer, auto restart, and energy saver mode. One degree temperature adjustment and four way air direction. Includes full feature remote control. Cooling Heating Power REG-81 8,000 3, V REG ,600/12,000 8,500/11, /230V REG ,200/18,500 13,000/16, /230V REG A* 18,200/18,500 9,100/11, /230V REG ,700/25,000 13,000/16, /230V *REG-183 is 30A maximum fuse/circuit breaker size; REG A is 20A maximum fuse/circuit breaker size. Room Air Heat Pumps Perfect for any room needing heating and cooling. Units change over to supplemental electric heat automatically at 40 o F outside temperature. Features electronic controls and wireless remote. For supplemental heat. Includes window mounting kit and support brackets. Cooling HP Heat Air Delivery RAH ,200/11,600 8,500/10, CFM RAH ,400/17,800 9,000/11, CFM 208/230V-1-60 Thru-the-Wall Series Sized to fit standard wall sleeve, includes interior trim kit. Four way air deflection and multiple fan speeds for comfort, plus 24-hour on-off timer and energy saver mode. Also auto operation and sleep modes. All models feature electronic controls and wireless remote. ENERGY STAR CERTIFIED MODELS: See for a complete listing of Comfort-Aire Energy Star certified room air conditioners. Cooling Heating Power BG-81 8, V BG , V BG-103 9,800/10, /230V BG , V BG ,700/12, /230V BG ,600/14, /230V BGE-103 9,800/10,000 8,600/10, /230V BGE ,700/12,000 8,600/10, /230V BGE ,600/14,000 8,600/10, /230V 11

14 Casement/Slide Air Conditioner Solves the problem of mounting a window A/C unit in a horizontal sliding or casement window. Features three fan speeds, easy-access filter, adjustable air deflection, and wireless remote. With energy saver mode, 24-hour on/off timer. Cooling Air Delivery Power CD , CFM 115V CD , CFM 115V For windows 20 5 /16" to 39 7 /16" high and starting at 15 1 /2" wide. Includes adjustable window mounting kit. Cooling Design Type EER PS-81A 8,100 Single Hose 8.9 PS-101A 10,000 Single Hose 8.9 PS-121A 12,000 Single Hose 8.9 Heat/ Cooling Heat Cool Design Type PSH-141A 14,000 Single Hose 11,000 PSH EER: 8.9, COP 2.6 Hose on all models is 48 long. 115V-1-60 PSH cooling and heating model. Portable A/C Ideal for any room where temporary cooling is needed (and heat with PSH-141A). Heavy duty casters and built-in handles make it easy to move unit. Built-in condensate management, electronic controls, 24 hour timer, and auto louver swing for gentle, breezelike effect. Includes sliding adapters for windows. PS cooling only models. Cooling s Nom. Cooling Heat Pumps Nom. Cooling Heating Capacity PTAC07A130A 7,000 PTHP07A130A 7,000 6,000 PTAC09A130A 9,000 PTHP09A130A 9,000 8,000 PTAC12A130A 12,000 PTHP12A130A 12,000 11,000 PTAC12A150A 12,000 PTHP12A150A 12,000 11,000 PTAC15A130A 15,000 PTHP15A130A 15,000 14,000 PTAC154150A 15,000 PTHP154150A 15,000 14,000 Electric heat standard: 7,000 and 9,000 models have 3kW electric heat; 12,000 and 15,000 models come with either 3kW or 5kW electric heat. Also available in 265V model. Package Terminal Units Includes electronic digital controls and temperature limiting for guest comfort and efficiency. All models include electric heat as standard. With built-in condensate and freeze protection. 208/230V , 50, 70 pint models Energy Star certified Portable Dehumidifiers Easy to use with top mounted controls. Unit automatically shuts off when bucket is full. BHDP models have built-in pump for fast direct draining. Features auto defrost and auto restart. Slide-out filter is easily removed for washing and reusing. Low temperature operation to 41 o F. 115V-1-60 NEW Large capacity 95-pint model with built-in pump Capacity per Day Bucket Capacity Shipping Weight BHD-301-H 30 pints 6.3 pints 30.9 lbs. BHD-501-H 50 pints 12.7 pints 38.6 lbs. BHD-701-H 70 pints 12.7 pints 41.9 lbs. BHDP-501-H 50 pints 12.7 pints 39.6 lbs. BHDP-701-H 70 pints 12.7 pints 42.9 lbs. BHDP-951-H 95 pints 21.1 pints 62.9 lbs. Condensate bucket is accessed from the front, has handy handholds on each side and an interior handle; unit can be adapted to direct drain. BHDP units with built-in pump can be used for direct drain or bucket can be used to collect condensate. 12

15 HTV/HTD/ HTH024 HTV/HTD/ HTH036 HTV/HTD/ HTH048 HTV/HTD/ HTH060 HTV/HTD/ HTH070 GEOTHERMAL/WATER SOURCE EQUIPMENT Capacity Modulation Specs for Ground Water Installation EER/COP : 28,700 cooling/24,800 heating : 22,000 cooling/17,700 heating : 43,300 cooling/37,200 heating : 31,300 cooling/26,100 heating : 55,800 cooling/48,400 heating : 42,000 cooling/35,000 heating : 71,500 cooling/63,200 heating : 53,100 cooling/44,000 heating : 77,700 cooling/71,400 heating : 60,800 cooling/53,200 heating 27.3/ / / / / / / / / /4.5 GeoLogix TM Plus Two Stage Geothermal Heat Pump Exceptional efficiency with variable speed ECM blower motor and two-stage scroll compressor. Features microprocessor controls and performance monitoring system. Ratings: Cooling at 59 o F entering water temp; heating at 50 o F entering water temperature. 208/ to 6 Tons HTV upflow shown right; HTD downflow center; HTH horizontal left HTS024 HTS036 HTS048 HTS060 Capacity Modulation Specs for Ground Water Installation EER/COP : 27,800 cooling/24,100 heating : 21,700 cooling/18,000 heating : 41,900 cooling/34,300 heating : 30,100 cooling/24,800 heating : 52,700 cooling/46,600 heating : 40,000 cooling/34,600 heating : 63,000 cooling/57,900 heating : 47,600 cooling/43,000 heating Ratings: Cooling at 59 o F entering water temperature; heating at 50 o F entering water temperature. Ratings above with WDG air handler matches; ratings vary with MWG coils. 24.9/ / / / / / / / / to 5 Tons GeoLogix TM Plus Two Stage Geothermal Heat Pump (Split) Exceptional efficiency with full/ part load shifting and two-stage scroll compressor. Features microprocessor controls, quiet operation and performance monitoring system. Cabinets Match with MWG multi-position coils or WDG air handlers. can be stacked for multi-unit installations. HEV/HEH 024 HEV/HEH 030 HEV/HEH 036 HEV/HEH 042 HEV/HEH 048 HEV/HEH 060 Capacity Modulation Specs for Ground Water Installation EER/COP : 26,500 cooling/23,000 heating : 20,300 cooling/16,700 heating : 32,300 cooling/30,000 heating : 24,900 cooling/22,000 heating : 38,200 cooling/35,100 heating : 29,000 cooling/24,900 heating : 46,300 cooling/42,300 heating : 35,200 cooling/30,500 heating : 51,800 cooling/45,000 heating : 39,200 cooling/32,600 heating : 68,000 cooling/55,400 heating : 50,400 cooling/39,800 heating 21.7/ / / / / / / / / / / /4.5 GeoLogix TM HEV Series Heat Pump Efficient, compact two stage heat pump with ECM blower motor, integrated digital communication controls, and scroll compressor. Large filter improves indoor air quality. Available in vertical or horizontal cabinet 208/ Ratings: Cooling at 59 o F entering water temperature; heating at 50 o F entering water temperature. 13

16 WDG Series Air Handlers for Geo Split Systems Can be installed for vertical upflow or downflow, and horizontal left or right airflow without switching any components. ECM blower motor delivers quiet operation with maximum efficiency. y insulated cabinet with factory installed A-coil; R-410A TXV. Ratings: cooling at 59 o F entering water temperature; heating at 50 o F entering water temperature. Electric heater kits available in 240V/208V, 2.9 to 14.4kW. Heater mounts internally in units; control board activates elements via internally wired low voltage harness. Cabinet Size AHRI Match Split HP Capacity Modulation Ground Water Cooling /EER Heating/COP WDG24VSA 18.5" x 44" HTS024 27,800/ ,100/4.60 WDG24VSB 22.5" x 55" HTS024 21,700/ ,000/5.00 WDG36VSB 22.5" x 55" HTS036 41,900/ ,300/4.70 WDG36VSC 25.5" x 59" HTS036 30,100/ ,800/5.00 WDG48VSB 22.5" x 55" HTS048 52,700/ ,600/4.60 WDG48VSC 25.5" x 59" HTS048 40,000/ ,600/5.00 WDG60VSC 25.5" x 59" HTS060 63,000/ ,900/ ,600/ ,000/4.60 MWG Series Coils for Geo Split Systems Cased coils are ideal for dual fuel add-on applications. y insulated cabinets come with dual right and left hand condensate drain connections. y insulated cabinet includes corrosion-proof drain pan. Equipped with TXV. AHRI certified when match with HTS split units. Approx. Air Flow CFM Coil Dimensions (in.) Width Depth Height MWG24TB 600/800 17½ 17 7 /8 20 MWG24TC 600/800 21½ 17½ 20 MWG36TC 825/ ½ 20 MWG36TD 825/ ½ 30 1 /4 32 MWG48TC 1000/ /8 28 MWG48TD 1000/ ½ 30 1 /4 32 MWG60TD 1050/ ½ 30 1 /4 32 Coils fit a variety of furnace models with widths of 17½", 21", and 24½". HWW Series Water-to-Water Systems For a wide range of residential and industrial applications including radiant floors, ice melting, potable hot water, etc. Capable of ground water, ground loop and water loop applications, with microprocessor controls, scroll compressor, performance monitoring system. Specs for Water Loop Installation EER/COP HWW036A : 32,300 cooling/43,100 heating 14.6/4.9 HWW060B : 52,800 cooling/72,700 heating 14.3/4.7 HWW120B : 105,600 cooling/145,400 heating 14.1/4.6 Ratings: cooling at 86 o F entering water temperature; heating at 68 o F entering water temperature. LoopLogix Geothermal Design Software Everything the contractor/ installer needs to design loop fields, compare different types of heating and cooling systems, and prepare presentations for homeowners. Even helps contractors compile a bill of materials once the system is selected. Go to to try it for yourself! LoopLogix software can be downloaded FREE! 14

17 Commercial Water Source Heat Pumps Ideal for replacements. For boiler/cooling tower applications; multiple units are connected by a water loop with independent control of each zone. Each unit can be operated year round in heating or cooling mode. Features performance monitoring system and quiet operation. Horizontal units come with factory-installed hanger brackets and discharge. Specs for Water Loop Installation EER/COP HBH/HBV006 : 5,800 cooling/7,500 heating 13.2/4.7 HBH/HBV009 : 8,800 cooling/11,600 heating 13.4/4.2 HBH/HBV012 : 11,700 cooling/15,200 heating 13.5/4.3 HBH/HBV015 : 14,500 cooling/17,300 heating 15.4/5.0 HBH/HBV018 : 17,300 cooling/21,500 heating 14.3/5.0 HBH/HBV024 : 23,700 cooling/28,500 heating 13.4/4.7 HBH/HBV030 : 28,100 cooling/35,100 heating 13.4/4.6 HBH/HBV036 : 34,500 cooling/45,200 heating 13.5/4.4 HBH/HBV042 : 40,100 cooling/52,700 heating 13.1/4.3 HBH/HBV048 : 47,700 cooling/55,900 heating 13.3/4.7 HBH/HBV060 : 59,400 cooling/77,000 heating 13.4/4.3 Water Loop installation: Cooling at 86 o F entering water temperature, heating at 68 o F entering water temperature. All units are available in right or left return. 208/230V-1, 208/230V-3, 460V, 575V, 265V offered, but all voltages are not available in all models. Specs for Water Loop Installation EER/COP HKV084A : 82,000 cooling/101,000 heating 15.2/4.8 HKV096A : 94,000 cooling/118,000 heating 15.0/4.7 HKV120A : 118,000 cooling/144,000 heating 15.0/5.0 HKV150A : 150,000 cooling/186,000 heating 14.0/4.7 HKV168A : 166,000 cooling/204,000 heating 15.5/4.9 HKV192A : 190,000 cooling/238,360 heating 15.3/4.8 HKV240A : 238,500 cooling/291,000 heating 15.3/5.1 HKV300A : 300,000 cooling/372,000 heating 14.0/4.7 Specs for Water Loop Installation EER/COP HBH072A : 69,000 cooling/92,500 heating 13.3/5.0 HBH096A : 95,000 cooling/123,000 heating 13.7/5.0 HBH120A : 119,000 cooling/160,000 heating 13.3/4.6 Large Capacity Commercial Water Source Heat Pumps Ideal for large spaces such as gyms, cafeterias, commons areas. Units feature microprocessor controls, performance monitoring system and dual circuits in the four largest models of the HKV series. Available in front or back return, and a variety of discharge locations and voltages. Cabinets are fully insulated and compressors have special design mounting for quiet operation. Water Loop installation: Cooling at 86 o F entering water temperature, heating at 68 o F entering water temperature. 208/230V-3-60, 460V-3-60, 575V-3-60 available. Multiple access panels simplify installation, especially in tight spots. HBH includes hanging brackets. 15

18 HRC Series Water Source Console A ductless solution where space is limited or structural integrity is required. Compact console is efficient and reliable, with microprocessor controls, performance monitoring system, and polyester powder coat finish on galvanized steel cabinet. With extended operating range, units are capable of ground loop as well as water loop (boiler-tower) installations. Installation options include right- or left-hand piping, front or bottom return air. Specs for Water Loop Installation EER/COP HRC09A : 8,600 cooling/11,400 heating 13.3/4.6 HRC12A : 11,300 cooling/14,100 heating 12.8/4.5 HRC15C : 13,700 cooling/17,500 heating 12.8/5.1 HRC18C : 15,600 cooling/20,100 heating 12.2/4.5 Specifications for HRC Console: Water Loop installation: Cooling at 86 o F WB entering air temperature, heating at 59 o F entering air temperature. Available voltages: 208/ , , FEATURES OF GEOTHERMAL & WATER SOURCE HEAT PUMPS Comfort-Aire geothermal and water source heat pumps are packed with features that promote reliability and peace of mind. Standard features include... t Extended range operation of 20 o to 120 o F makes units suitable for virtually all climate and applications t Microprocessor controls simplify installation and servicing, and assure reliable operation;, some geothermal units using DXM digital communicating controls t Variety of configurations available, depending on model, for application and installation flexibility t Performance monitoring system signals if the unit isn t at perak performance so service can be schedule, much like a car s check engine light t Eight safeties standard that protect the unit and the compressor, including anti-short cycle, over- and under-voltage, loss of charge, high refrigerant pressure, and more t Compressor mounting system that s specially enginered to reduce vibration and maintain quiet operation Features may vary from model to model Geothermal Accessories See brochure HCI-GTA-B for all accessories Comfort-aire offers a full line of accessories for geothermal installations. All the details, specifications and details are contained in our Accessories brochure. f o r r e s i d e n t i a l s y s t e m s Geothermal systems offer an effective way to cut utility costs while ensuring comfort. Heat Controller s line includes two stage and single stage geothermal heat pumps, both package and split system types. Additionally, Heat Controller offers a full range of accessories required to configure and install these systems. this catalog contains the following geothermal accessory products and specification guides: Product Page Deluxe Flow Center...1 Standard Flow Center...3 Double O-Ring Flow Center...5 O-Ring Fittings...6 Pressurized Loop Pump...7 Geothermal Accessory Fittings...8 Flow Meter Tool...9 Fusion Kit...9 Flush Cart...10 Commercial Accessories...11 United States legislation allowing tax credits has been enacted to encourage energy efficient installations in new construction as well as for existing homes. All our geothermal heat pumps are so efficient they are eligible for Federal tax credits up to 30% of the total installation cost with no upper limit. For details of the program and qualifying equipment, see: 16

19 Rest Assured: Value-Added Programs When you buy Comfort-Aire products, you r purchasing the peace of mind that comes from dealing with a company that s been in the comfort business for over 75 years. We have a well-deserved rputation not only for quality products but also for standing behind those products with excellent warranty and support programs. Warranty Coverage Comfort-Aire backs all its products with some of the strongest warranties in the industry. For instance, our AHRI-matched cooling and heating split systems are warranted for 12 years years from date of purchase, and heat exchangers of our 92% and 95% gas furnaces have lifetime warranties. These limited express warranties are subject to certain restrictions: see our web site for full warranty details. Technical Support Experienced technicians can help diagnose and solve installation, operation and service issues over the phone, and they re backed up by sales representatives throughout the country who are knowledgeable about our products and their applications. Web Site Support Our web site is another resource with owners manuals, installation and operation manuals, replacement parts lists, and service manuals. By registering for our Channel ner site, distributors and contractors have access to all these technical documents 24/7. This catalog is intended as a handy overview of the entire Comfort-Aire product line. For more detailed AITONS EQUIPMENT

20 over three-quarters of a century. generations. Founded in 1933, we can actually trace our beginnings to the Wingert Furnace Company which began building coal, gas and oil furnaces in Headquartered in Jackson, Michigan, since 1955, our facility, our staff and our product offerings have grown over the years to meet changes in the HVAC industry, including emerging technologies and regulatory requirements. Our line runs the gamut from 5,000 room air conditioners to 25 ton commercial units. We re your source for a wide range of equipment that meets a variety of applications plus most needed accessories and service parts. minimum order quantities, and we ship freight pre-paid on orders of 30 units or more (drop ship charges may apply). Twice a year we offer stocking programs with great discounts and heat of summer, you run out of condensers or mini-splits or whatever, there s a good chance we ll have what you need in our warehouse and, in many instances, we ll be able to ship next day. All of which makes it easy for you to control your inventory while meeting your customers needs. with outstanding warranties and after-sale support. Experienced technicians can help diagnose and solve installation and service issues over the phone, and they re backed up by knowledgeable sales representatives throughout the country. Our web site is another resource with owners manuals, technical documentation, and warranty claim submittal available at any time. expectations of our distributors, our dealers and the consumers who buy our products. AITONS EQUIPMENT 35 Brownridge Road, Unit 6 Halton Hills, Ontario L7G 0C CA-50-15A SP 2M 1/15 Copyright 2015 Heat Controller. All rights reserved.