SAM-e - Short Absorption Manifold Submittal Drawings

Transcription

1 SAM-e - Short Absorption Manifold Submittal Drawings Date: Job Name: Contractor: Contractor or Order No.: Engineer: Agent: Agent P.O. No.: Date Ordered: Date Required: Walter Meier (Climate USA) Inc. 826 Proctor Ave., Odgensburg, NY Tel: nortec@waltermeier.com Walter Meier (Climate Canada) Ltd Fenton Road, Ottawa, Ontario K1T3T7 Tel: Fax: NORTEC B l 24 MAR 2011

2 Loa d Duct dim ension Tag lbs/hr W idth Height RH before RH after Conditions Absorption dista nce re quire d Absorption dista nce ca lcula te d Header Distributor Header and Adapter Configuration Mounting Frame (Optional) Tag Type (3", 6", 9" o r 12" C enters) Atmospheric or Pressurized PN Length (in.) Qty PN PN PN SAM-e Selection - 2 -

3 Duct/AHU Width Pressurized Steam Main Tap steam from top of pressurized steam main Manual Shut-Off Valve (By Others) Duct/AHU Height Strainer Actuator & Valve Separator 6 min. 6 Min F & T Steam Trap 1 Air Gap Manual Shut-Off Valve (By Others) Drain NOTE: Steam hose/piping should not reach bottom of the funnel Return to non-pressurized condensate return main Pressurized condensate return main Note: The SAM-e header functions as a steam separator, therefore an external steam separator is not required. Steam components in grey are provided by Nortec. Tap steam from top of pressurize steam main to avoid excess condensate. Condensate from SAM-e to be returned to atmospheric floor drain. When pressurized steam enters the SAM-e, the pressure drops down to almost atmospheric pressure. Therefore, it must be drained atmospherically, and the use of a condensate pump (rated for 212ºF) must be used to raise the condensate to a higher elevation. Pressurized Plumbing with External Separator - 3 -

4 Tap steam from top of pressurized steam main Pressurized Steam Main Manual Shut-Off Valve (By Others) Strainer 6 Min. 6 min. 1 Air Gap Drain Pressurized condensate return main Return to non-pressurized floor drain Steam components in grey are provided by Nortec. Tap steam from top of pressurize steam main to avoid excess condensate. Condensate from separator to be returned to pressurized condensate main. Condensate from SAM-e to be returned to atmospheric floor drain. When pressurized steam enters the SAM-e, the pressure drops down to almost atmospheric pressure. Therefore, it must be drained atmospherically, and the use of a condensate pump (rated for 212ºF) must be used to raise the condensate to a higher elevation. Pressurized Plumbing without External Separator - 4 -

5 A Internal Baffle Plate DETAILA All pressurized SAM-e inlet kits come with a standard internal baffle plate. The baffle plate redirects the flow of steam causing condensate to fall out, eliminating the need to install an external steam separator. SAM-e Internal Baffle Plate 02/15/11-5 -

6 Duct/AHU Width Duct/AHU Height Atmospheric steam inlet Use Nortec supplied steam hose and gear clamps 6 min. 12 or 20 Stand OPTIONAL 1" Air Gap To Prevent Back Siphonage Drain NOTE: Steam hose/piping should not reach bottom of the funnel. 6 min. Or 2 higher than duct static pressure AHU Floor Drain Water Cooler Option: 1/2 NPT Cold water inlet 2 NPT Tempered Water Drain 6 min. 1" Air Gap To Prevent Back Siphonage 1" NPT to 3/4 NPT Reducer (Supplied By Others) 6 min. Or 2 higher than duct static pressure To drain 3/4 NPT Manual dump valve Typical SAM-e Installation for Atmospheric Steam Applications 11/15/05-6 -

7 8-3/16 (20.7 CM) CENTER TO CENTER TOP MOUNTING FRAME B TOP CENTER TO CENTER MOUNTING FRAME 8-1/2 (21.6 CM) CENTER TO CENTER BOTTOM MOUNTING LEGS A BOTTOM CENTER TO CENTER MOUNTING LEGS 3/4 (1.9 cm) A 2-1/8 (5.4 cm) min. 9-2/3 (25.6 cm) max. MOUNTING FRAME STEAM TUBE D E HEADER 1-1/2 (3.8 cm) 8-11/16 (22.1 cm) LEG MOUNT 8-1/2 (21.6 CM) BOTTOM CENTER TO CENTER MOUNTING LEGS STEAM INLET MULT. OPTIONS 3/4 NPT CONDENSATE 5 (12.7 cm) C 10 (25.4 CM) DETAIL A 8-3/16 (20.7 CM) TOP CENTER TO CENTER MOUNTING FRAME General SAM-e Dimensions 04/27/06-7 -

8 D uct W idth D im ension A Fram e W idth - Bottom SA M -e Dim en sions Wid th Dim en sion B Fram e W idth - Top Dim en sion C Header A ssem bly Width in m m in m m in m m in m m D uct H eight Dim en sion D S team T ube Height S A M-e Dim ensions Heigh t Dim en sion E M in. Min im um Overall Heig ht Dim en sion E M ax. Max im um Overall Height in m m in m m in m m in m m General SAM-e Dimensions 03/24/11-8 -

9 7/16 (1.1 CM) 6-1/2 (16.5cm) CENTER TO CENTER BOTTOM MOUNTING LEG 6-5/8 (15.8 cm) A Mini Steam Tube C Mini Steam Tube B 3-9/16 (9.1 cm) 3-3/16 (8.1 cm) 5" (12.7 cm) Steam INLET MULT. OPTIONS 3/4 NPT CONDENSATE OUTLET General Mini SAM-e Dimensions 03/24/11-9 -

10 Mini SAM-e Dimensions Width Duct Width Dimension A Mini SAM-e Width in mm in mm Mini SAM-e Dimensions Height Duct Height Dimension B Mini SAM-e Height Dimension C Mini Steam Tube Height in mm in mm in mm General Mini SAM-e Dimensions 03/24/

11 Atmospheric SAM-e HEADER FOR OVER 801 LB/HR Center to Center 6.95 Second 4 inlet for SAM-e over 801 lb/hr Assembly rod, washer, and nuts for field mounting, supplied by others. Bolt, nut, and washer assembly supplied by Nortec. Top Distributor Bracket Duct Width Alternate attachment configuration without mounting frame Steam Tube Duct Height H= Width of Selected Manifold Template is included for hole cut outs Steam Inlet Condensate Drain Insure connections extend from duct. H Header mounting brackets supplied by Nortec. In-duct / AHU Installation WITHOUT mounting frame. Installation & Dimensions Atmospheric. 02/22/

12 Atmospheric SAM-e HEADER FOR OVER 801 LB/HR Center to Center 6.95 Second 4 inlet for SAM-e over 801 lb/hr Bolt, nut, and washer assembly supplied by others. Duct Width Duct Height H= Width of Selected Manifold Template is included for hole cut outs Steam Inlet Condensate Drain Insure connections extend from duct. H Allow spacing for fastening of pivoting heads to top of duct. Header mounting brackets supplied by Nortec. In-duct / AHU Installation WITH mounting frame. Installation & Dimensions Atmospheric. 02/22/

13 Atmospheric SAM-e HEADER FOR OVER 801 LB/HR 2.12 X (cut out length) Center to Center 6.95 Second 4 inlet for SAM-e over 801 lb/hr OR (cut out width) 2 dia. for every hole Assembly rod, washer, and nuts for field mounting, supplied by others. Bolt, nut, and washer assembly supplied by Nortec. Top Distributor Bracket X= H Duct Width Alternate attachment configuration Steam Tube Duct Height H= Width of Selected Manifold Install manifold flush with duct Steam Inlet Condensate Drain H Header mounting brackets supplied by Nortec. Outside Duct Installation WITHOUT mounting frame. Installation & Dimensions Atmospheric. 02/22/

14 Atmospheric SAM-e HEADER FOR OVER 801 LB/HR 2.12 X (cut out length) Center to Center Second 4 inlet for SAM-e over 801 lb/hr OR (cut out width) 2 dia. for every hole X= H Bolt, nut, and washer assembly supplied by other. Duct Width Duct Height H= Width of Selected Manifold Steam Inlet Condensate Drain H Header mounting brackets supplied by Nortec. Outside Duct Installation WITH mounting frame. Installation & Dimensions Atmospheric. 02/22/

15 Airflow Duct Section Bolt, nut, and washer assembly supplied by others. Min. 10 Manifold bracket must be rotated to accommodate 10º angle. Drain must be at lowest point. NOTE: Header can not be installed outside the duct in vertical applications. Vertical Duct installation - SAM-e 02/20/

16 Short-Absorption Manifold (SAM-e) Duct or AHU Stainless steel steam tubes SAM-e (Short Absoption Manifold) Can be installed in the Horizontal duct or vertical Duct or a AHU. Reference SAM-e Installtion Manual Galvanized Mounting Frame Optional 6" Long hose cuff for 1.75" dia. tubing 4" long hose cuff for 3" & 4" dia. tubing and 2 gear clamps for steam line connection. (By Nortec) 12" 2" Stainless Steel Steam Header 3/4" NPT Condensate Return 6 " Min 6" min., P-Trap must be 2" more than duct static pressure Condensate Return to drain or sump pump Primary wire and disconnect (By Others) Standard Telescopic Stand (By Nortec) Drain water cooler and F & T Steam trap(s) Located inside unit. Installed at Nortec Typical SE Installation 1. This drawing is for reference only. Installation must conform to all local codes. 2. Refer to physical data drawings for dimensions. Copper or S.S. pipe - 1" Insulation Recommanded 6" Long hose cuff and 2 gear clamps for steam line connection. (by Nortec) Water supply 30 to 80 psig Pressurized steam connection from Boiler Max. 15 psi Min. 5 psi Controls (By Nortec or by Others) Union (by Others) 6 " Min Steam Valve and Actuator must be located 6" max. from the SE humidifier. Inlet located on top of unit for SE models 475 to Valve and Actuator must be installed horizontally. Refer to the Invensys installation manual for details. Wye strainer (By Nortec) Steam trap (By Nortec or by Others) Return to nonpressurized system, by gravity only 1/2" NPT Supply water connection. (Manual shut-off valve by Others) 3/4" O.D. Drain connection to funnel drain or sump pump Funnel with 1" air gap supplied by others 1/2" NPT Aux. Drain, Optional Plugged at factory (Shut-off valve by Others) Open floor drain must be properly sized and rated for maximum temperature requirements. Steam condensate drain. Return to nonpressurized system, by gravity only Typical SE Installation

17 Adapter Dimensions Atmospheric SAM-e

18 SAM-e Inlet and Adapter Configurations Inlet and Adapter Configurations for Atmospheric Steam Part Number Description Inlet Adapter Kit, SAM-e, 33 lbs/hr 1 x 3/4" Inlet Adapter Kit 1, SAM-e, 100 lbs/hr 1 x 1.75" Inlet Adapter Kit 2, SAM-e, 200 lbs/hr 2 x 1.75" Inlet Adapter Kit 3, SAM-e, 300 lbs/hr 3 x 1.75" Inlet Adapter Kit 4, SAM-e, 400 lbs/hr 4 x 1.75" Inlet Adapter Kit 5, SAM-e, 500 lbs/hr 5 x 1.75" Inlet Adapter Kit 6, SAM-e, 600 lbs/hr 6 x 1.75" Inlet Adapter Kit 7, SAM-e, 700 lbs/hr 7 x 1.75" Inlet Adapter Kit 8, SAM-e, 800 lbs/hr 8 x 1.75" Inlet Adapter Kit 23, SAM-e, 300 lbs/hr 1 x 3" Inlet Adapter Kit 24, SAM-e, 600 lbs/hr 1 x 4" Inlet Adapter Kit 25, SAM-e, 800 lbs/hr 1 x 3" + 1 x 4" Inlet Adapter Kit 26, SAM-e, 800 lbs/hr 2 x 4" Inlet Adapter Kit 27, SAM-e, 1200 lbs/hr 2 x 3" Inlet Adapter Kit 28, SAM-e, 100 lbs/hr 3" to 1.75" Inlet Adapter Kit 29, SAM-e, 300 lbs/hr 4" to 3" Inlet Adapter Kit 30, SAM-e, 1200 lbs/hr 3 x 4" SAM-e Inlet and Adapter Configurations Inlet and Adapter Configurations for Pressure Steam Part Number Description Inlet Adapter, SAM-e, Pressure Steam 1/2" npt Inlet Adapter, SAM-e, Pressure Steam 3/4" npt Inlet Adapter, SAM-e, Pressure Steam 1" npt Inlet Adapter, SAM-e, Pressure Steam 1-1/4" npt Inlet Adapter, SAM-e, Pressure Steam 2-1/2" npt Inlet Adapter, SAM-e, Pressure Steam 2" npt Inlet Adapter, SAM-e, Pressure Steam 2-1/2" npt 1. Consult SAM-e Shop Drawings for more details. 2. All adapters come complete with hose/clamp connections for all outlets. 3. All electrode humidifiers must run individual steam lines directly to SAM-e. SAM-e Inlet and Adapter Configurations 23/11/

19 Header and Inlet Adapter Configuration for Atmospheric Units SAM-e Header SAM-e Header SAM-e Header Kit 1, Kit 2, Kit 3, SAM-e Header SAM-e header SAM-e header Adapter located at SAM-e Adapter located at SAM-e Kit 4, Kit 5, Kit 6, SAM-e header SAM-e header Kit 7, Adapter located at SAM-e Kit 8, Adapter located at SAM-e Atmospheric Steam Header and Inlet Adapter Configuration 23/11/

20 Kit 23 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. 1 Steam Inlet 3 O.D. 1 Condensate Drain 3/4 NPT Represents steam line by others. For Representative Purposes Only Inlet / Adapter SAM-e lbs/hr with 1X3 connection, Part # /26/

21 Kit 24 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. Steam Inlet 4 O.D. Condensate Drain 3/4 NPT Represents steam line by others. For Representative Purposes Only Inlet / Adapter SAM-e lbs/hr with 1X4 connection, Part # /26/

22 Kit 25 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. 1 Steam 3 O.D. line connection 1 Steam 4 O.D. 2 Condensate Drains 3/4 NPT (Not Shown) line connection Represents steam line by others. For Representative Purposes Only Inlet / Adapter SAM-e lbs/hr with 1X3 + 1x4 connections, Part # /26/04

23 Kit 26 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. 2 Steam 4 O.D. line connections 2 Condensate Drains 3/4 NPT (Not Shown) For Representative Purposes Only Represents steam line by others. *Adapter Located at Steam Exchange Humidifier with Low Pressure Steam Inlet Inlet / Adapter SAM-e 800 lbs/hr with 2X4 connections, Part # /26/04

24 Kit 27 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. 2 Steam 4 O.D. line connections Condensate Drain 3/4 NPT Represents steam line by others. For Representative Purposes Only Inlet / Adapter SAM-e lbs/hr with 2X4 connections, Part # /26/

25 Kit 28 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. Represents steam line by others. 1 Condensate Drain 3/4" NPT 1 Steam line connection 1-3/4 O.D. 3-1/8 x 1-5/8 Fitting Reducer (Copper) Located at Steam Exchange Humidifier with low pressure inlet steam. For Representative Purposes Only Inlet / Adapter SAM-e 100 lbs/hr with 3 to 1.75, Part # /26/04

26 Kit 29 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. Represents steam line by others. 1 Condensate Drain 3/4" NPT 1 Steam line connection 3 O.D. 4-1/8 x 3-1/8 Fitting Reducer (Copper) Located at Steam Exchange Humidifier with low pressure inlet steam. For Representative Purposes Only Inlet / Adapter SAM-e 300 lbs/hr with 4 to 3, Part # /08/05

27 Kit 30 NOTE: Every steam line connection(s) includes hose cuff(s) and clamps by Nortec. 2 Steam 4 O.D. line connections Condensate Drain 3/4 NPT 3 Steam 4 O.D. line connections From Humidifier Represents steam line by others. For Representative Purposes Only Inlet / Adapter SAM-e 1200 lbs/hr 3X4 Part # /26/