STX Accu-Temp Electric Kettle Instructions

Transcription

1 Accu-Temp Cordless Electric Kettle STX Accu-Temp Electric Kettle Instructions

2

3 Model Power Supply Capacity Net Weight SPECIFICATIONS PARTS STX-AT-EK 110/120 V, 60 Hz 1.8 Liters 2.8 lbs.. Overall Dimensions (L x W x H) 8.5 x 8.5 x 10.4 Control System Strix Technology* *All Strix controls are designed to meet all relevant international standards and approvals and are manufactured to consistenly exceed 12,000 cycles of normal operation. Lid Spout Lid Release Button Handle Kettle Water Level WIndow Base Temperature Selection Buttons - 1 -

4 IMPORTANT SAFEGUARDS Basic safety procedures should be used whenever using any electrical appliance. Please read and understand all instructions prior to using this product. FOR HOUSEHOLD USE ONLY. ALWAYS USE HANDLE. KETTLE SURFACE WILL BE HOT TO TOUCH. FOR YOUR SAFETY AND OPTIMAL PERFORMANCE PLEASE READ Always use the kettle handle during operation. Kettle surface will be very hot during use and initially during cooling. Scalding could occur. Use 120V power source. Keep out of the reach of children. Do not leave this devise unattended when in use. To avoid electrical shock, DO NOT IMMERSE CORD, PLUG, OR BASE UNIT IN WATER or other liquids. Do not operate this appliance with wet hands or near standing water. Always check the condition of the power cord and plug. If there is any evidence of a damaged or fraying cord, or if the appliance has malfunctioned, or if the appliance has been damaged, discontinue use and contact STX International (See CONTACT INFORMATION). Do not allow the power cord to hang over the edge of a table or counter. Not intended for outdoor use. Do not place the kettle near or on a hot gas or electric burner, or in a heated oven. Only use the power base provided with the appliance. The use of accessory attachments is not recommended and will void all guarantee/warranties. Do not use appliance for other than intended use. Always use this appliance on a level surface. Do not overfill the kettle. Pour hot liquids slowly and carefully. Do not over tilt the kettle

5 It is not recommended to open the lid while the water is heating or boiling. Scalding may occur if the lid is opened during the heating cycle. Always ensure that the kettle is turned off before cleaning or after use and prior to unplugging from the wall outlet. Ensure that this appliance is turned off and disconnected from any power source when not in use. Do not use in dusty conditions. Avoid use near strong magnets or strong electrical currents. Do not drop the kettle. Do not attempt to repair, open or alter any components without the written approval of STX International (See CONTACT INFORMATION). Any attempt to repair or modify this product without the approval STX International will void all guarantee/warranties. Do not operate this appliance in an appliance garage or under a wall cabinet. When storing this appliance in an appliance garage or under a wall cabinet, always unplug the unit from any power source. Not doing so will increase the risk of a fire. Ensure that the stored appliance is not in contact with the walls of a cabinet or appliance garage. Ensure that the kettle is kept clean. Please read the Cleaning Storage Decalcifying instructions in this manual. WARNING! Risk of Fire or Electric Shock CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: SHOCK HAZARD - DO NOT OPEN Within the product enclosure there is uninsulated dangerous voltage that may be of sufficient magnitude to constitute a risk of fire or electric shock to persons

6 FEATURES 1. 6 Temperature Settings 160 F, 175 F, 180 F, 190 F, 200 F, 212 F Liter (7.6 cups) Capacity 3. Stainless Steel Construction 4. Concealed Heating Element 5. Boil Dry Protection 6. Automatic Shut Off 7. Enhanced Keep Warm Function 8. Cord Storage 9. Removable Filter 10. Cordless Kettle Rotating Base 12. BPA-Free Plastic Water Lelvel Window (all parts that come in contact with water are BPA-Free) 13. Anti-Drip Design Spout 14. Strix Heating Element GETTING STARTED 1. Remove any packaging material and promotional labels before using your electric kettle for the first time. 2. Read and understand the Owner s Manual prior to using this appliance. 3. It is recommended that you retain the packaging materials in the event that any future shipping of this appliance is necessary. 4. The manufacturer recommends that prior to usage you fill the kettle to the maximum level with water, bring to a boil and then discard all of the water. This will sanitize the unit before usage. NOTE: This appliance is designed for boiling drinking water only; never use it to heat or boil any other liquids or foodstuffs. The lid should always be firmly in place and locked closed before use

7 CLEANING & STORAGE 1. Always ensure that the base unit is turned off, unplugged from the wall outlet, and that the kettle has cooled sufficiently to touch prior to any cleaning or storage. Wipe down the exterior of the kettle with a moist cloth. 2. When storing, stow the cord beneath the base unit and make sure that the lid is closed and that the kettle is correctly attached to the base. Do not place anything on top of the kettle during storage. 3. Periodically it may be necessary to remove mineral deposits that build up. These deposits are associated with the mineral content of tap water and therefore how often you will need to descale your kettle will depend on the level of calcium in your water supply. This calcium build up may look like a discoloration on the inside of the kettle. 4. To remove mineral deposits you can purchase kettle descaler products from most supermarkets or hardware stores and follow the directions on the packaging. HOME DECALCIFYING To home decalcify, open the kettle lid and fill with 3 cups of white vinegar and add water to the maximum level. Bring to boil. Once the solution is boiling turn off the kettle and unplug base. Let it sit for 20 minutes and then pour out. Rinse the kettle. You may need to rinse the kettle several times so there is no trace of vinegar in the kettle. Remove the solution the following day, refill with fresh water and bring to a boil. Then discard the water. Repeat as necessary to remove any build up. OPERATING INSTRUCTIONS POSITIONING THE KETTLE 1. Ensure that the kettle base is positioned on a safe, level, and stable work area. 2. Remove as much of the power cord from the underside of the power base (cable storage area) as necessary to connect to a wall outlet. 3. Ensure that the power cable does not extend over the work area

8 4. Always Keep out of reach of children. 5. Keep base away from any flammable materials. 6. After pouring hot water, return the hot kettle to the base or a suitable heat resistant or heat protected surface. FILLING THE KETTLE 1. Always remove the kettle from the base before adding water. 2. Open the lid by pressing the lid button on the handle. 3. Never add water while the kettle is positioned directly above the heating element. 4. Add fresh, cold water. Never add any liquid other than water. The water level should be greater than the minimal level (approximately 3.5 cups or.8 Liters), but not to exceed the maximum level (7.6 cups or 1.8 Liters). 5. Push the lid closed until it locks into position. 6. Place the kettle on the power base. Plug the base into an electrical outlet. The base will beep twice. NOTES: Use deionized/purified water when possible for best taste and to minimize mineral build-up in the kettle. Remove any residual water from the kettle s outside housing prior to placing the kettle on the base. Do not fill above Maximum Level indicator. REGULAR HEATING MODE The Regular Heating Mode is designed to heat the kettle to the desired temperature and once the designated temperature has been reached, the LED light on the base will turn off and the base will automatically turn off. 1. Select the desired setting by pressing one of the six buttons. 2. The base will beep once and the selected button LED will turn red

9 3. Once the temperature has been achieved the base will beep 5 times, the base heating element will automatically turn off, and the red LED will turn off. 4. Whenever you remove the kettle from the plugged-in base it will turn off. This is a safety feature to eliminate the potential for electrical shock or fire with an exposed hot base. NOTES: You can cancel the selected temperature at any time by pressing the selected temperature button again. This will shut off the base. Fog and condensation will appear in lid and water level view, this is typical. You cannot select a lower temperature once the kettle has heated to a designated setting until after it has had time to cool down. When heating water to the highest temperature (212 F), the kettle may vibrate slightly on the base. This is expected. KEEP WARM MODE The Enhanced Keep Warm Mode is designed to allow the kettle to maintain a designated temperature for up to 30 minutes. During this mode, each time the kettle is removed and replaced, the kettle will be reheated to the designated temperature. During this mode the kettle base will beep for 10 seconds each time the kettle is removed from the base and beep once when it is replaced. It will automatically reheat to the designated temperature. This mode will be maintained for up to 30 minutes. After approximately 30 minutes the base will automatically turn off. 1. Fill the kettle as directed (see FILLING THE KETTLE). 2. Place the kettle on the base. 3. Select the desired setting by pressing AND HOLDING one of the six buttons for 3 seconds. It will beep three times and the button LED will light up red while the kettle is heating. Once the kettle reaches the designated temperature, the kettle will beep once and the LED will change to blinking blue to indicate the Enhanced Keep Warm Mode is functioning

10 4. When the kettle is removed from the base, the base will turn off. Once the kettle is placed back on the base, you can select the desired setting again and the blue light will illuminate and start blinking again. This reactivates the enhanced keep warm mode. The kettle will then reheat to the designated temperature if necessary. This function will continue for up to 30 minutes. 5. To turn off the unit, press the blinking button. BOIL DRY PROTECTION As a safety feature, this kettle is designed to automatically turn off when insufficient water has been kept in the kettle. This feature is designed to prevent overheating of the appliance. When this feature is triggered the unit is designed to shut off. To reset the unit, unplug the unit from the wall outlet. Allow the kettle to cool completely. Once the kettle has cooled, refill the kettle to the correct level with water and plug the unit back into the wall socket. The safety boil dry protection will automatically reset. FILTER The kettle has a removable filter just inside the lid by the spout. The filter can be removed to clean with hot water and soap. Do not run the filter through the dishwasher. To properly insert the filter, place the filter in as shown in the picture below

11 TEA HEATING & STEEPING RECOMMENDATIONS (Individual taste and preference may differ) 160 F 175 F 180 F 190 F 200 F 212 F Delicate Tea Green Tea White Tea Oolong Teas Coffe & Other Teas Black Tea 1-2 min 2-3 min 2-3 min 3-4 min 4-5 min 3-5 min White Tea Arabian Night Asatsuya Bancha Ceylon Green Chin Chun Mee Darjelling Green Dragon Well Fukamushi Gyokuro Jasmine Kukicha Nepal Green Peah Pi Lo Chun Sencha Shincha Souchong Apple Black Cherry Blackcurrant China Yin Zhen Coconut Elderflower Ginger Lemon Lychee Mango Orange Peony Snowbird Strawberry Most Varieties Instant Coffe Pressed Coffee Ceylon China Lapsang China Rose Darjelling Earl Grey English Breakfast Indian Chai Irish Breakfast Keemun Orange Pekoe Russian Samovar Vanilla Assam Bagged Tea Chai Chamomile Chinnamon Golden Yunnan Herbal KEnya Lapsang Souchong Lemongrass Peppermint Red Rooibos Spearmint Whole Leaf - 9 -

12 SAFETY INSTRUCTIONS 1. Please read all instructions prior to operating this appliance. Please keep this manual for future reference. Failure to comply with the safety instructions and/or operating instructions contained in this manual will void any warranty. The manufacturer/seller accepts no liability for damages caused by failure to comply with the owner s manual or negligent use of this product. 2. Check for damaged parts prior to use. check that all parts are operating properly and perform their intended functions. 3. Always check the condition of the power cord prior to use. If there is any evidence of damage or fraying of the power cord discontinue use and contact STX International for OEM replacement. (see Contact Information on the back of this manual) STX International will only use original OEM parts when/if replacement is necessary. 4. Always disconnect the unit from the power source before servicing or cleaning the unit. Unplug the unit when not in use. Do not plug the unit into an already damaged outlet. 5. This product is designed for indoor household use only. It is NOT a commercial use product. Do NOT use for commercial industrial purposes. 6. Do NOT operate outdoors or near any flammable or combustible materials. Do NOT use during eletrical storms. 7. Keep out of the reach of children. Never leave this device unattended. 8. It is important to monitor this product while in use. Do not leave this unit unattended when plugged into an outlet or powered ON. 9. To prevent electric shock and damage to the unit, do NOT imerse the main unit in water. 10. Do not operate this unit near an open flame or any hot surface

13 11. Do not unplug the unit by pulling on the electrical cord itself. Never unplug the unit with wet hands. 12. Always use 110/120 Volt power sources. DO NOT USE POWER CONVERTERS (210/220V). 13. Do not plug another high wattage appliance into the same outlet as this product. 14. Do NOT operate under the influence of alcohol or drugs. 15. Any alteration of this unit s components, substitution of other manufacturer s components to this unit, or any repairs to this grinder not completed or authorized by STX International will immediately void all guarantees/warranties. 16. Electrical repair or any other type of service must be done by the seller (The Mercantile Station 2 / STX International). Proof of purchase must be provided by consumer prior to any repair/service acceptance. The seller will use only OEM parts and accessories.

14 3-YEAR WARRANTY All STX International Products come with a 3-Year Guarantee, valid only in the 48 Contiguous United States. If you purchase this product and ship it to a destination outside of the 48 Contiguous United States this warranty becomes null and void. The first 30 Days are covered by a Money Back or Replacement Guarantee from the date of the receipt of the product. If your product becomes damaged in shipment or is found to be defective in any way during this period, we will replace or issue a complete refund for your product upon return. We will pay all shipping involved during this first 30- day period. The remainder of the 3 Years (after the first 30 days) is covered by a FREE REPAIR Guarantee (parts and labor included). If anything becomes defective during this period we will fix the issue and provide a full service inspection to your product, shipping (to & from) will be paid by the buyer. Please us at Info@STXInternational.com to set up a service request. Returns of New/Unused Products If you have Buyer's Remorse and decide that you do not want the product, it must be returned NEW & UNUSED in the original box and you will pay the return shipping. PLEASE NOTE: There will be a 10% Restocking Fee and original Shipping Costs (if applicable) will not be refunded. Used product cannot be returned. How To Register Your Warranty Go to Click on "Register Your Warranty" tab and fill out the form. This is a fully secure website. Your information will never be sold or misused in any way. This registration site is strictly for order verification that will be used to speed up the process should you ever need to use your Warranty for service. STX International 2159 Magnum Circle, Lincoln, NE Info@STXInternational.com

15

16 QUESTIONS, PROBLEMS OR COMPLIMENTS? Thank You for purchasing this STX International Product! We are grateful for your business! All of our STX International Products are inspected then sealed with our NEW Product Seal prior to shipment. Our goal is to ensure Quality, Completeness, and Satisfaction for your order. For Any Questions, Problems, or Compliments please call or us. Toll Free: Our Business Hours are: Monday - Thursday: 8am - 4pm CST Friday: 8am - Noon CST If you would like to shop for other STX International Products Please visit our website STX International 2159 Magnum Circle, Lincoln, NE Info@STXInternational.com