T16. (Battery) Rider Scrubber Operator Manual. North America / International

Transcription

1 T16 (Battery) Rider Scrubber Operator Manual The Safe Scrubbing Alternative ES Extended Scrub System TennantTrue Parts Hygenic Fully Cleanable Tanks IRIS a Tennant Technology North America / International To view, print or download the latest manual, visit: Rev. 06 ( ) * *

2 INTRODUCTION This manual is furnished with each new model. It provides necessary operation and maintenance instructions. Read this manual completely and understand the machine before operating or servicing it. This machine will provide excellent service. However, the best results will be obtained at minimum costs if: The machine is operated with reasonable care. The machine is maintained regularly - per the machine maintenance instructions provided. The machine is maintained with manufacturer supplied or equivalent parts. PROTECT THE ENVIRONMENT Please dispose of packaging materials, used components such as batteries and fluids in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. MACHINE DATA Please fill out at time of installation for future reference. Model No. Serial No. Installation Date INTENDED USE The T16 is an industrial/commercial rider machine designed to wet scrub both rough and smooth hard surfaces (concrete, tile, stone, synthetic, etc). Typical applications include schools, hospitals / health care facilities, office buildings, and retail centers. Do not use this machine on soil, grass, artificial turf, or carpeted surfaces. This machine is intended for indoor use only. This machine is not intended for use on public roadways. Do not use this machine other than described in this Operator Manual. Tennant Company PO Box 1452 Minneapolis, MN Phone: (800) or (763) Touch N Go, 1 STEP, Grip N Go, Dura Track, Positive Drain Control, SmartRelease, Duramer, FaST PAK, Insta Fit are trademarks of Tennant Company. Flow-Rite is a registered trademark of Flow Rite Controls. Hydrolink is a registered trademark of Trojan Battery Company. Specifications and parts are subject to change without notice. Original Instructions, copyright TENNANT Company, Printed in U.S.A.

3 CONTENTS CONTENTS Page Important Safety Instructions Save These Instructions... 3 Operation... 6 Machine Components... 6 Controls And Instruments... 7 Touch Panel... 8 Symbol Definitions... 9 Installing Batteries Battery Specifications Operation Of Controls Battery Discharge Indicator Hour Meter Recovery Tank Indicator Solution Tank Indicator Power Kill Switch Operating / Hazard Light Switch (Option) Seat Support Arm Operator Seat Deluxe Suspension Seat (Option) Seat Belts Contrast Control Button Configuration Mode Button Propel Pedal Brake Pedal Directional Switch Vacuum Fan / Squeegee Button Solution On / Off Buttons How The Machine Works Brush And Pad Information While Operating The Machine Pre Operation Checklist Starting The Machine Filling The Solution Tank Foam Scrubbing (Fast Mode) / Ec H2o Scrubbing (Ec H2o Mode) Conventional Scrubbing Mode Es (Extended Scrub) Mode Setting Scrub Modes Setting Brush Pressure Setting Solution Flow Conventional Solution Flow Es (Extended Scrub) Solution Flow Scrubbing Double Scrubbing Water Pickup Mode (No Scrubbing) Stop Scrubbing Draining And Cleaning The Recovery Tank 27 Draining And Cleaning The Solution Tank (Es Machines Only) Turn Off The Machine Fault Indicator(S) Warning Codes Options Side Brush (Option) Pre Sweep Assembly (Option) T ( ) Page Empty The Pre Sweep Debris Hopper 34 Vacuum Wand (Option) Rollout Battery (Option) Rear Squeegee Guard (Option) Spray Nozzle (Option) Machine Troubleshooting Maintenance Maintenance Chart Yellow Touch Points Lubrication Steering Chain Steering Gear Chain Rear Squeegee Casters Batteries Checking The Electrolyte Level Checking Connections / Cleaning Charging The Batteries (Off Board Charger) Charging The Batteries (On Board Charger) On Board Battery Charger Error Codes 49 On Board Charger Settings Changing The On Board Battery Charger Fuse Flow Rite Battery Watering System (Option) Hydrolink Battery Watering System (Option) Circuit Breakers Electric Motors Scrub Brushes Disk Brushes And Pads Replacing Disk Brushes Or Pad Drivers 57 Replacing Disk Scrub Pads Cylindrical Brushes Replacing Cylindrical Scrub Brushes.. 59 Side Brush (Option) Replacing The Side Brush Pre Sweep Brushes Replacing The Pre Sweep Disk Brushes 61 Replacing The Pre Sweep Cylindrical Brush Fast System Replacing The Fast Pak Carton Cleaning The Fast Supply Hose Connector Replacing The Fast Injector Filters Ec H2o Module Flush Procedure Squeegee Blades Replacing (Or Rotating) The Rear Squeegee Blades Leveling The Rear Squeegee Adjusting The Rear Squeegee Blade Deflection Replacing Or Rotating The Side Squeegee Blades Replacing Or Rotating The Side Brush Squeegee Blades (Option)

4 CONTENTS Page Skirts And Seals Pre Sweep Side Skirts (Option) Pre Sweep Recirculation Skirt (Option) 75 Pre Sweep Rear Skirt (Option) Belts Cylindrical Brush Drive Belts Pre Sweep Brush Drive Belt (Option). 76 Tires Pushing, Towing, And Transporting The Machine Pushing Or Towing The Machine Transporting The Machine Machine Jacking Storage Information Freeze Protection (Machines Without Optional Ec H2o System) Preparing The Machine For Operation (Machines Without Optional Ec H2o System) Freeze Protection (Machines With Optional Ec H2o System) Priming The Ec H2o System Specifications General Machine Dimensions/Capacities. 85 General Machine Performance Power Type Tires Fast System (Option) Ec H2o System (Option) Side Brush Solution Flow Rate (Option).. 87 Machine Dimensions T ( )

5 SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS The following precautions are used throughout this manual as indicated in their description: WARNING: To warn of hazards or unsafe practices that could result in severe personal injury or death. FOR SAFETY: To identify actions that must be followed for safe operation of equipment. The following information signals potentially dangerous conditions to the operator. Know when these conditions can exist. Locate all safety devices on the machine. Report machine damage or faulty operation immediately. WARNING: Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tank(s). WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. WARNING: Electrical Hazard Disconnect Battery Cables and Charger Plug Before Servicing Machine. Do Not Charge Batteries with Damaged Power Supply Cord. Do Not Modify Plug. If the charger supply cord is damaged or broken, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. FOR SAFETY: 1. Do not operate machine: Unless trained and authorized. Unless operator manual is read and understood. Under the influence of alcohol or drugs. While using a cell phone or other types of electronic devices. Unless mentally and physically capable of following machine instructions. With brake disabled. If it is not in proper operating condition. With pads or accessories not supplied or approved by Tennant. The use of other pads may impair safety. In outdoor areas. This machine is for indoor use only. In areas where flammable vapors/liquids or combustible dusts are present. In areas that are too dark to safely see the controls or operate the machine unless operating / headlights are turned on. In areas with possible falling objects unless equipped with overhead guard. 2. Before starting machine: Check machine for fluid leaks. Make sure all safety devices are in place and operate properly. Check brakes and steering for proper operation. Adjust seat and fasten seat belt (if equipped). WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This machine may be equipped with technology that automatically communicates over the cellular network. If this machine will be operated where cell phone use is restricted because of concerns related to equipment interference, please contact a Tennant representative for information on how to disable the cellular communication functionality. T ( ) 3

6 SAFETY PRECAUTIONS 3. When using machine: Use only as described in this manual. Use brakes to stop machine. Go slowly on inclines and slippery surfaces. Do not scrub on ramp inclines that exceed 7% grade or transport (GVWR) on ramp inclines that exceed 14% grade. Reduce speed when turning. Keep all parts of body inside operator station while machine is moving. Always be aware of surroundings while operating machine. Use care when reversing machine. Keep children and unauthorized persons away from machine. Do not carry passengers on any part of the machine. Always follow safety and traffic rules. Report machine damage or faulty operation immediately. Follow mixing, handling and disposal instructions on chemical containers. Follow site safety guidelines concerning backup alarms. Follow site safety guidelines concerning wet floors. 4. Before leaving or servicing machine: Stop on level surface. Turn off machine and remove key. 5. When servicing machine: All work must be done with sufficient lighting and visibility. Keep work area well ventilated. Avoid moving parts. Do not wear loose clothing, jewelry and secure long hair. Block machine tires before jacking machine up. Jack machine up at designated locations only. Support machine with jack stands. Use hoist or jack that will support the weight of the machine. Do not push or tow the machine without an operator in the seat controlling the machine. Do not power spray or hose off machine near electrical components. Disconnect battery connections and charger cord before working on machine. Do not use incompatible battery chargers as this may damage battery packs and potentially cause a fire. Inspect charger cord regularly for damage. Do not disconnect the off board charger s DC cord from the machine receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first. Avoid contact with battery acid. Keep all metal objects off batteries. Use a non conductive battery removal device. Use a hoist and adequate assistance when lifting batteries. Battery installation must be done by trained personnel. Follow site safety guidelines concerning battery removal. All repairs must be performed by a trained service mechanic. Do not modify the machine from its original design. Use Tennant supplied or approved replacement parts. Wear personal protective equipment as needed and where recommended in this manual. For Safety: wear hearing protection. For Safety: wear protective gloves. For Safety: wear eye protection. For Safety: wear protective dust mask. 6. When loading/unloading machine onto/off truck or trailer. Drain tanks before loading machine. Lower scrub head and squeegee before tying down machine. Turn off machine and remove key. Use ramp, truck or trailer that will support the weight of the machine and operator. Do not load/unload on ramp inclines that exceed 19% grade. Use winch. Do not push the machine onto/off the truck or trailer unless the load height is 380 mm (15 in) or less from the ground. Block machine tires. Tie machine down to truck or trailer. 4 T ( )

7 SAFETY PRECAUTIONS The safety labels appear on the machine in the locations indicated. Replace damaged labels. WARNING LABEL Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging WARNING LABEL Flammable materials or reactive metals can cause explosion or fire. Do not pick up. WARNING LABEL Flammable materials can cause explosion or fire. Do not use flammable materials in tank Located on seat panel. Located on underside of recovery tanks cover and on circuit breaker panel. Located on underside of solution tank cover. FOR SAFETY LABEL Read manual before operating machine. Located on circuit breaker panel. T ( ) 5

8 OPERATION OPERATION MACHINE COMPONENTS O A B C D N E M F L I H G J K A. Recovery tank B. Recovery tank cover C. Backup alarm / flashing light (option) D. Solution tank cover E. Solution tank F. Rear squeegee G. Side squeegee H. Scrub head I. Battery compartment J. Pre Sweep assembly (option) K. Pre Sweep side brushes (option) L. Pre Sweep debris hopper (option) M. Side brush (option) N. Operator seat O. FaST PAK (option) ec H20 System Module (option) FaST solution system (option) T (3 2011)

9 OPERATION CONTROLS AND INSTRUMENTS A B K J C I D H G E F A. Steering wheel B. Touch panel C. Side brush switch (option) D. Spray nozzle switch (option) E. Brake pedal F. Propel pedal G. Directional switch H. Operating lights / hazard lights switch (option) I. Key switch J. Pre Sweep switch (option) K. Power kill switch T (1 2011) 7

10 OPERATION TOUCH PANEL A C B D I H G F E J M K L N P O Q R Q A. Horn B. Warning / fault indicator light C. Battery discharge indicator D. Hour meter E. Configuration mode button F. Recovery tank indicator G. LCD display H. Solution tank indicator I. Contrast control button J. Brush pressure button K. Brush pressure indicator lights L. 1 Step button M. Scrub mode (ec H2O / FaST / ES / conventional) button N. Vacuum fan / squeegee button O. Solution increase button (+) P. Solution decrease button ( ) Q. Solution on / off buttons R. Solution flow indicator lights 8 T (1 2011)

11 OPERATION SYMBOL DEFINITIONS These symbols are used on the machine to identify controls, displays, and features. Fault indicator Recovery tank Vacuum fan / squeegee Operating lights 1 STEP Hazard light ES (extended scrub) Scrub mode FaST (foam scrubbing) Circuit breaker ec H2O (option) Spray nozzle Solution flow Pre Sweep Increase Pre sweep / Vacuum fan Decrease On Main brush pressure Off Side brush Solution On / Off Battery charge Emergency shutoff Horn Contrast control Hour meter Jack point Solution tank Solution flow (maximum / minimum) Forward / Reverse Brush pressure (maximum / minimum) T (1 2011) 9

12 OPERATION INSTALLING BATTERIES 3. Remove the accessory box and tray. WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks And Open Flame Away. Keep Battery Hood Open When Charging. FOR SAFETY: When servicing machine, wear protective gloves and eye protection when handling batteries and battery cables. Avoid contact with battery acid. Battery installation must be done by trained personnel. BATTERY SPECIFICATIONS Six 6 volt deep cycle lead acid batteries. Maximum battery dimensions: 7 in / mm W x 11.8 in / mm L x 14.5 in / 368 mm H. 1. Park the machine on a level surface and remove the key. 2. To engage the seat support, lift the seat completely open and insert the seat support arm into the hole in the operator seat plate. 4. With adequate assistance carefully install the batteries into the battery compartment tray and arrange the battery posts as shown. Insert the foam spacers along side the batteries as shown if installing the smaller batteries. NOTE: For large traction batteries, remove the seat assembly and use a hoist to install the battery. Foam Spacer Foam Spacer Foam Spacer Front of machine 5. Using the supplied battery post boots, connect the cables to the battery posts, RED TO POSITIVE (+) & BLACK TO NEGATIVE ( ). 6. Reinstall the accessory box and tray. IMPORTANT: Make sure that the charger is properly set for the battery type before charging (See ON BOARD CHARGER SETTINGS). 10 T ( )

13 OPERATION OPERATION OF CONTROLS BATTERY DISCHARGE INDICATOR The battery discharge indicator displays the charge level of the batteries while the machine is operating. RECOVERY TANK INDICATOR The recovery tank indicator displays the amount of liquid in the recovery tank. All scrubbing functions will stop when the recovery tank is full. Empty the recovery tank when the indicator reaches 100%. SOLUTION TANK INDICATOR When the batteries are fully charged, all five bars are lit. Recharge the batteries when there are no longer any bars shown in the display. NOTE: The reading on the battery discharge indicator is not accurate when the machine is first powered on. Operate the machine a few minutes before reading the charge level of the batteries. The solution tank indicator displays the amount of liquid in the solution tank. Refill the solution tank when there are no longer any bars shown in the display. The machine will stop scrubbing when the solution tank is empty. NOTE: The battery discharge indicator will not reset from the flashing indicator (lowest bar on the indicator) unless the batteries have been fully charged. HOUR METER The Hour meter records the hours the machine was operated. Use this information to determine machine service intervals. T ( ) 11

14 OPERATION POWER KILL SWITCH The power kill switch immediately stops all power to the machine. Stop machine power: Press the power kill switch. Restart machine power: Turn the power kill switch to the right to release the switch. Turn the key switch off, then turn the key fully clockwise and release it to the On position. SEAT SUPPORT ARM The seat support arm holds the seat up to allow access to the batteries and circuit breakers. To engage the seat support arm, lift the seat completely open and insert the seat support arm into the hole in the operator seat plate. OPERATING / HAZARD LIGHT SWITCH (OPTION) Operating and Hazard Lights On: Press the top of the Operating / hazard light switch. Operating Lights On: Press the Operating / hazard light switch to the middle position. All Lights Off: Press the bottom of the Operating / hazard light switch. 12 T (1 2011)

15 OPERATION OPERATOR SEAT The front to back adjustment lever adjusts the seat position. The lumbar knob adjusts the lower backrest portion of the seat. DELUXE SUSPENSION SEAT (OPTION) The operator seat has four adjustments: backrest angle, operator weight, lumbar, and front to back. The front to back adjustment lever adjusts the seat position. Use caution when tilting the deluxe seat. The deluxe seat is heavier than the standard seat. The backrest adjustment knob adjusts the angle of the backrest. SEAT BELTS FOR SAFETY: Before starting machine, adjust seat and fasten seat belt. The weight adjustment knob controls the firmness of the operator seat. Use the gauge next to the weight adjustment knob to help determine seat firmness. T (1 2011) 13

16 OPERATION CONTRAST CONTROL BUTTON Use the Contrast control button to darken / lighten the LCD display. BRAKE PEDAL Press the Brake pedal to stop the machine. CONFIGURATION MODE BUTTON The Configuration mode button is for accessing the configuration and diagnostic modes. Only properly trained service personnel and TENNANT representatives should access these modes. DIRECTIONAL SWITCH Use the Directional switch to select either the forward or reverse direction. Press the propel pedal to move the machine. PROPEL PEDAL Press the Propel pedal to move the machine. NOTE: An audible alarm will sound when the Directional switch is placed into reverse. NOTE: Machines equipped with the optional flashing light / backup alarm only: The optional backup light and alarm will function only when the machine is moving in reverse. 14 T (1 2011)

17 OPERATION VACUUM FAN / SQUEEGEE BUTTON Lower squeegee and turn vacuum fan on: Press the Vacuum fan / squeegee button. The indicator light will illuminate when the squeegee is lowered. Raise squeegee and turn vacuum fan off: Press the Vacuum fan / squeegee button. The indicator light will go out when the squeegee is raised. NOTE: The 1 STEP button does not need to be activated to operate the vacuum fan / squeegee system. The vacuum fan / squeegee button can be turned on or turned off with the 1 STEP button either on or off. SOLUTION ON / OFF BUTTONS Shut off the solution flow: Press the Solution on / off button to shut off the solution flow. All the solution flow indicator lights will turn off. Turn on the solution flow: Press the Solution on / off button to turn on the solution flow. The solution indicator lights will turn back on and the solution flow will default to the last setting used. T (1 2011) 15

18 OPERATION HOW THE MACHINE WORKS The 1 STEP button makes it possible to immediately begin scrubbing by operating all the scrubbing functions. When in the conventional Scrub mode, a water and detergent mixture is used to scrub the floor. When in the optional ES (Extended Scrub) mode, the dirty solution in the recovery tank is filtered through the ES system and returned to the solution tank for reuse. Detergent is then injected into the returned solution to revitalize the cleaning capability of the solution. T16 With Disk Brushes T16 With Cylindrical Brushes When in the optional FaST (Foam scrubbing) mode, the FaST scrubbing system mixes the FaST PAK concentrate with a small amount of water, creating a large volume of expanded wet foam. The FaST system can be used with all scrubbing applications. When in the optional ec H2O (electrically converted water) mode, normal water passes through a module where it is oxygenated and charged with an electric current. The electrically converted water changes into a blended acidic and alkaline solution forming a neutral ph cleaner. The converted water attacks the dirt, breaks it into smaller particles, and pulls it off the floor surface allowing the machine to easily scrub away the suspended soil. The converted water then returns to normal water in the recovery tank. The ec H2O system can be used with all double scrubbing and heavy duty scrubbing applications. 16 T ( )

19 OPERATION BRUSH AND PAD INFORMATION For best results, use the appropriate brush or pad for the cleaning application. Listed below are brushes and pads and the applications for which each is best suited. NOTE: The amount and type of soilage play an important role in determining the type of brush or pad to use. Contact a Tennant representative for specific recommendations. Nylon brush (Disk)* Softer nylon bristles are recommended for scrubbing coated floors. Cleans without scuffing. High productivity pad (Black) Aggressively strips floor finishes/sealers. Use for very heavy duty scrubbing. This pad can only be used with the grip pad driver, not the tufted pad driver. Surface preparation pad (Maroon) Aggressively strips floors without use of chemicals. Grip pad driver The grip face backing allows pads to be fully used and holds pads in place without penetrating the pad. The spring activated centering device works with all Tennant pads and allows for fast, easy pad replacement. Polyester brush (Cylindrical) Softer general purpose polyester bristles gently clean while scrubbing. Perfect for sensitive floor surfaces. Polyester does not absorb water so it is preferred over Nylon in wet applications. PolyPro brush (Cylindrical) Heavy duty polypropylene bristles provide a more aggressive cleaning performance and can more easily lift compacted dirt, debris, and sand while offering excellent scrubbing performance. Polypropylene brush (Cylindrical and Disk)* General purpose polypropylene bristles lift lightly compacted dirt without scuffing high-gloss coated floors. Tufted pad driver Standard pad driver has short bristles, or tufts, on the back to hold the pad in place. This driver works with all Tennant pads except the black high productivity pad. Super AB brush (Cylindrical and Disk)* Nylon fiber with an abrasive grit to remove stains and compacted dirt. Aggressive action on any surface. Performs well on buildup, grease, or tire marks. * This brush is also available for the side brush. Stripping pad (Brown) Quickly and easily cuts through old finish to prepare the floor for recoating. Scrubbing pad (Blue) Removes dirt, spills, and scuffs. Leaves a clean surface ready for recoating. Buffing pad (Red) Quickly cleans and removes scuff marks while polishing the floor to a high gloss. Polishing pad (White) Maintains a high gloss. Use for buffing very soft finishes and lower traffic areas, and polishing soft waxes on wood floors. T ( ) 17

20 OPERATION WHILE OPERATING THE MACHINE Pick up oversized debris before scrubbing. Pick up wire, string, twine, large pieces of wood, or any other debris that could become wrapped around or tangled in the brushes. Drive in a straight a path as possible. Avoid bumping into posts or scraping the sides of the machine. Overlap the scrub paths by several centimeters (a few inches). Avoid turning the steering wheel too sharply when the machine is in motion. The machine is very responsive to the movement of the steering wheel. Avoid sudden turns, except in emergencies. Adjust the machine speed, brush pressure, and solution flow as required when scrubbing. Use the lowest brush pressure and solution flow settings for best performance. If poor cleaning performance is observed, stop cleaning and refer to MACHINE TROUBLESHOOTING in this manual. Perform the Daily Maintenance Procedures after each use (see MACHINE MAINTENANCE in this manual). Drive the machine slowly on inclines. Use the brake pedal to control machine speed on descending inclines. Scrub with the machine up inclines rather than down inclines. FOR SAFETY: When using machine, go slowly on inclines and slippery surfaces. Do not operate machine in areas where the ambient temperature is above 43 C (110 F). Do not operate scrubbing functions in areas where the ambient temperature is below freezing 0 C (32 F). 18 T ( )

21 OPERATION PRE OPERATION CHECKLIST Perform the following steps before operating the machine: Check the machine for fluid leaks. Check the operating lights. Check left side squeegee for wear and damage. Check main brushes for wear and damage. Remove wire, string, or twine wrapped around the main scrub brushes. Machines equipped with cylindrical brushes: Confirm the debris tray is empty and clean. Machines equipped with side brush option: Check for wire, string, or twine wrapped around the scrub brush. FaST Scrubbing: Check the FaST PAK concentrate agent level, replace carton as needed. See the INSTALLING THE FaST PAK AGENT section of the manual. For FaST or ec H2O Scrubbing: Confirm all conventional cleaning agents/restorers are drained and rinsed from the solution tank. For FaST or ec H2O Scrubbing: Confirm the solution tank is filled with clear cool water only. Check the horn, headlights, taillights, safety lights, and backup alarm (if equipped). Check the brakes and steering for proper operation. Check the tires for damage. Check maintenance records to determine maintenance requirements. Machines equipped with side brush option: Check squeegee for wear and damage. Machines equipped with Pre Sweep option: Check for wire, string, or twine wrapped around the scrub brush. Machines equipped with Pre Sweep option: Check dust control filter bag. Machines equipped with Pre Sweep option: Confirm debris trough is empty. Check the rear squeegees for wear and damage. Check the recovery and solution tank cover seals for wear or damage. Confirm the vacuum fan inlet filter is clean. Check the right side squeegee for wear and damage. Machines equipped with ES option: Ensure ES filter at bottom of recovery tank is clean. T ( ) 19

22 OPERATION STARTING THE MACHINE FILLING THE SOLUTION TANK FOR SAFETY: Before starting machine, adjust seat and fasten seat belt. 1. Sit in the operators seat. 2. Turn the key switch completely past the on position and release the key switch. The key switch will automatically return to the on position. FOAM SCRUBBING (FaST MODE) / ec H2O SCRUBBING (ec H2O MODE) FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Open the solution tank cover. 3. Turn on lights (if equipped). 4. Place the directional switch into the direction needed to travel. 5. Press the propel pedal to move the machine. 2. Fill the solution tank with only clean COOL WATER (less than 21 C / 70 F). DO NOT use hot water or add any conventional floor cleaning detergents or a FaST or ec H2O system failure may result. Fill the solution tank with water until the level is approximately 50 mm (2 in) below the indicator tab. NOTE: The machine will not travel unless the operator is sitting in the operator seat. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tank(s). NOTE: Do not use the FaST or ec H2O system when there are conventional cleaning detergents in the solution tank. Drain, rinse, and refill the solution tank with clear cool water before operating the FaST or ec H2O system. Conventional cleaning detergents may cause a FaST or ec H2O system failure. 3. Close the solution tank cover. 20 T ( )

23 OPERATION CONVENTIONAL SCRUBBING MODE FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Open the solution tank cover. 2. Partially fill solution tank with water (not to exceed 60 C / 140 F). Pour the required amount of detergent into the solution tank. Continue filling the solution tank with water until the level is approximately 50 mm (2 in) below the indicator tab. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tank(s). ATTENTION: For Conventional Scrubbing, only use recommended cleaning detergents. Machine damage due to improper detergent usage will void the manufacturer s warranty. NOTE: Pour a recommended foam control solution into the recovery tank if excessive foam appears. For specific detergent recommendations, contact a Tennant representative. 3. Close the solution tank cover. T ( ) 21

24 OPERATION ES (EXTENDED SCRUB) MODE FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Open the solution tank cover. 4. Fill the ES detergent tank with detergent. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tank(s). 2. Fill solution tank with water (not to exceed 60 C / 140 F). Fill the solution tank with water until the level is approximately 50 mm (2 in) below the indicator tab. 5. Close the solution tank cover. 3. Fill the recovery tank with water (not to exceed 60 C / 140 F). Fill the recovery tank to just above the top of the ES filter. 22 T ( )

25 OPERATION SETTING SCRUB MODES The Scrub mode button enables the scrubbing functions to come on when the 1 STEP button is activated. The light and cleaning system logo next to the button will come on. The machine will default to the last setting used when it is powered on or off. SETTING SOLUTION FLOW With the 1 STEP button activated, press either Solution increase button (+) or Solution decrease button ( ) to set the solution flow level. Travel speed and floor conditions will affect scrubbing performance. The machine will default to the last setting used when the machine is powered on or off. The solution flow indicator lights display the current solution flow setting. NOTE: When using the FaST or ec H2O system (option), the solution flow increase and solution flow decrease buttons are nonfunctional. The FaST and ec H2O system flow rates are pre set. All three solution flow indicator lights will be lit if the machine is in the ec H2O or FaST mode. NOTE: When the ES system is turned on there is a slight delay before the ES pump begins operating. SETTING BRUSH PRESSURE Under normal cleaning conditions, the brush pressure should be set to the lowest setting (the bottom light). Under heavy grime conditions, the brush pressure can be set to a higher setting (the top two lights). Travel speed and floor conditions will affect cleaning performance. With the 1 STEP button activated, press the Brush pressure button to set the brush pressure. Use the Brush pressure button to both raise or lower the brush pressure settings. If brushes are worn, it may be necessary to increase the brush pressure. The machine will default to the last setting used when it is powered on or off. CONVENTIONAL SOLUTION FLOW Under normal soilage conditions the solution flow level should be set to the lowest setting (the left light). Under heavy grime conditions, the solution flow level should be set to the higher settings (middle or right lights). ES (EXTENDED SCRUB) SOLUTION FLOW For ES machines, the detergent flow is turned off when the solution flow is in the lowest setting (one light). The middle setting (two lights) and highest setting (three lights) allow solution AND detergent flow. The lowest setting (one light) allows solution flow WITHOUT adding detergent. Detergent does not have to be continuously added with the solution flow to attain effective scrubbing results. Under normal soilage conditions, the solution flow level should be alternated between the middle and lowest setting. T (1 2011) 23

26 OPERATION SCRUBBING FOR SAFETY: Do not operate machine, unless operator manual is read and understood. 1. Start the machine. 2. Press the 1 STEP button. The light near the button will come on. All the preset scrubbing functions will turn on. NOTE: DO NOT turn on the FaST or ec H2O system during conventional scrubbing. Conventional cleaning detergents could cause a FaST or ec H2O system failure. Drain, rinse, and refill the solution tank with cool clean water before operating the FaST or ec H2O system. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. FOR SAFETY: When using machine, go slowly on inclines and slippery surfaces. NOTE: The squeegee automatically rises when the machine is driven in reverse. This prevents damage to the squeegee. ec H2O Model: If an alarm sounds and the warning / fault indicator indicator light flashes the ec H2O module must be flushed to resume ec H2O operation (See ec H2O MODULE FLUSH PROCEDURE). 3. Press the scrub mode button to select the scrub mode (ec H2O, FaST, or ES). The indicator light and mode logo will illuminate. NOTE: When the alarm sounds press the scrub mode button to shut off the ec H2O system and continue scrubbing or flush the ec H2O system. ec H2O SYSTEM INDICATOR LIGHT CODE Solid blue indicator light Flashing red warning / fault indicator light Solid red warning / fault indicator light CONDITION Normal operation Flush ec H2O module Contact Service Center 7. Release the directional pedal and press the brake pedal to stop the machine. 4. If necessary, adjust the brush pressure and solution flow. 8. Press the 1 STEP button to stop scrubbing. The light near the button will go off and scrubbing functions will stop after a short delay. 5. Place the directional switch in the direction the machine is to be moved (forward or reverse). 6. Press the propel pedal to begin scrubbing. 24 T (2 2011)

27 OPERATION DOUBLE SCRUBBING Use the double scrubbing method to clean heavily soiled areas. Double scrubbing can be performed using the FaST SCRUBBING SYSTEM (option), ec H2O SCRUBBING SYSTEM (option) or CONVENTIONAL SCRUBBING methods. Pre sweep and side brush (option) machines: Leave the Pre sweep and side brush (options) in the raised position while double scrubbing. To raise the side squeegees for double scrubbing, remove the clevis pins from the storage locations. Manually raise both side squeegee assemblies, then reinsert the pins into the holes in the side squeegee brackets. Before scrubbing the floor a second time, lower the side squeegees and press the Vacuum fan/squeegee button to lower the rear squeegee and turn on the vacuum fan. The light above the button will come on. Scrub the floor a second time to pick up the cleaning solution. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. NOTE: To turn off the solution flow when scrubbing the area a second time, press the Solution on / off button Press the Solution on / off button again to restart the solution flow. NOTE: Double scrubbing is not recommended in areas where the cleaning solution will run under racks or damage products. Press the 1 STEP button and then the Vacuum fan/squeegee button. The light above the Scrub vacuum fan/squeegee button will turn off, the squeegee will rise, and the vacuum fan will stop operating. Scrub the heavily soiled area. Let the cleaning solution soak on the floor for 5 15 minutes. FOR SAFETY: When using machine, go slowly on inclines and slippery surfaces. T (1 2011) 25

28 OPERATION WATER PICKUP MODE (NO SCRUBBING) STOP SCRUBBING The machine can be used to pick up water or non flammable liquid spills without scrubbing. To pick up water or non flammable liquid spills, make sure the 1 STEP button is not activated. The light above the button must be off. 1. While the machine is still in motion, press the 1 Step button to stop the scrubbing operations. The squeegee will briefly remain lowered to the floor to pick up the water in the scrub head. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. 2. Release the propel pedal and press the brake pedal to stop the machine. Press the Vacuum fan/squeegee button. The light above the button will come on, the squeegee will lower, and the vacuum fan will start operating. Pick up the water or non flammable liquid spill. 26 T (1 2011)

29 OPERATION DRAINING AND CLEANING THE RECOVERY TANK 4. If necessary, twist the drain nozzle to another position to adjust the flow rate. Drain and clean the recovery tank daily or when the recovery tank full fault code appears on the LCD display. Clean the outside of the tank with vinyl cleaner. 1. Drive the machine near a floor drain. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and remove key. 2. Unhook the recovery tank drain hose from the recovery tank. 5. Lift the recovery tank cover and flush out the recovery tank with clean water. Rinse the sensor near the top of the tank 3. Hold the drain hose near a floor drain, twist the drain nozzle open, and place the hose near the floor drain. NOTE: Be sure the drain hose nozzle is pointed in a safe direction before opening the nozzle. T ( ) 27

30 OPERATION 6. ES machines: Rinse the ES filter at the bottom of the tank and the sensor near the top of the tank. 9. Check the vacuum fan inlet filter daily. Clean inlet filter with a damp cloth or hose when dirty. Allow filter to completely dry before reinstalling it into the machine. NOTE: DO NOT use steam to clean the tanks. Excessive heat can damage the tanks and components. 7. To prevent leaks, clean the plug portion of the nozzle and the interior of the drain hose cuff. 10. Close the recovery tank cover. 11. Cylindrical scrub head: Remove and clean the debris trough. Place the trough back in the scrub head when clean. 8. Twist the drain cuff closed and hook the drain hose back onto the recovery tank. NOTE: The scrub head must be lowered approximately 25 mm (1 in) to remove debris trough. NOTE: The debris trough can be removed from the right side of the machine only. 28 T ( )

31 OPERATION DRAINING AND CLEANING THE SOLUTION TANK (ES MACHINES ONLY) 4. If necessary, twist the drain nozzle to another position to adjust the flow rate. ES machines: The solution tank should be drained and cleaned when the recovery tank is drained and cleaned. Clean the outside of the tank with vinyl cleaner. 1. Drive the machine near a floor drain. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and remove key. 2. Unhook the solution tank drain hose from the solution tank. 5. Lift the solution tank cover and flush out the solution tank with clean water. Rinse the filter and sensor located inside the solution tank. 3. Hold the drain hose near a floor drain, twist the drain nozzle open, and place the hose near the floor drain. NOTE: Be sure the drain hose nozzle is pointed in a safe direction before opening the nozzle. NOTE: DO NOT use steam to clean the tanks. Excessive heat can damage the tanks and components. T ( ) 29

32 OPERATION 6. To prevent leaks, clean the plug portion of the nozzle and the interior of the drain hose cuff. TURN OFF THE MACHINE 1. Remove foot from the propel pedal. 2. Press the 1 Step button to stop scrubbing. 3. Press the brake pedal to stop the machine. 4. Turn the key switch to the off position. 7. Twist the drain cuff closed and hook the drain hose back onto the solution tank. 30 T ( )

33 OPERATION FAULT INDICATOR(S) This machine is equipped with two visual indicators, a red indicator light and an LCD (liquid crystal display). The red indicator light will blink continuously indicating that a fault has occurred. The LCD will display a fault code. If there is more than one fault, each fault code will alternately display. All faults codes are also accompanied by an audible alarm to alert the operator a fault has occurred. To reset the fault indicators, turn the machine off, then eliminate the cause of the fault. The fault indicator will reset when the machine is restarted. Refer to the table below to determine the cause and remedy for the fault. Fault Code Cause(s) Remedy (Displayed in LCD) F1: Rec Tank Full Recovery tank is full Empty recovery tank F2: Sol Tank Empty Solution tank is empty Fill solution tank. F3: Vac # Flt # vacuum fan motor(s) not operating Shut off and restart machine. If fault code still appears, stop using machine and contact Tennant service representative. F4: Batt Very Low Low battery charge Recharge battery F5: Propel Error Propel controller error Turn off and restart machine. F6: Left Br Flt # Left brush not operating If fault code still appears, stop using machine and contact Tennant service representative. F6: Frnt Br Flt# Front brush not operating F7: Rght Br Flt# Right brush not operating F7: Rear Br Flt# Rear brush not operating F8: Hi B3 Current Side brush not operating F11: Act Timeout Main head actuator time out fault F12: Check Brushes Brushes not operating F13: Brsh Mtr Flt Brush motor(s) not operating T (1 2011) 31

34 OPERATION WARNING CODES Warning codes are typically caused by the operator attempting to activate modes that are not available. The warning code will appear in the LCD. Refer to the table below to determine the cause of the warning code. Warning Code (Displayed in LCD) Cause(s) Remedy W1: Batt. Low Low battery charge Charge batteries W2: Sqge Stall Squeegee not lowering Check squeegee / squeegee actuator for obstructions or damage W3: Side Stall Side brush not lowering Check side brush actuator for obstructions W4: Unavailable Optional solution not enabled Solution mode not available W5: No Side Brush Side brush not enabled Side brush not available W6: Not Used W7: Not Active Button inactive Button not active for use W8: No Vac. Amps Vacuum fan not operating Check harness connection. Reconnect W9: Open R/R Brush Right / rear brush not operating W10: Open L/F Brush Left / front brush not operating W11: Open SD Brush Side brush not operating harness if it is unconnected. If warning code still appears, stop using machine and contact Tennant service representative. W12: Solution Off No solution flow to scrub head Press Solution on / off button to start solution flow. 32 T (1 2011)

35 OPERATION OPTIONS SIDE BRUSH (OPTION) The side brush moves debris into the path of the main brushes. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. 1. Turn on the machine 2. Press the 1 Step button. 3. Press the top of the side brush switch to lower and start the side brush. PRE SWEEP ASSEMBLY (OPTION) The Pre Sweep assembly is mounted to the front of the machine and gives the machine the added ability to pick up debris. The assembly contains a main brush and two side brushes which sweep debris into a debris hopper. Periodically empty the debris hopper and vacuum debris bag. The machine may be operated with or without the Pre Sweep assembly. Refer to PRE SWEEP in the MAINTENANCE section for maintenance. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. 1. Turn on the machine 2. Press the 1 Step button. NOTE: Do not press the 1 Step button if only using to sweep. The Pre Sweep can be used without the scrubbing features. 3. Press the Pre Sweep switch to the middle position to start the Pre Sweep without dust control. Press the Pre Sweep switch to the top position to start the Pre Sweep with dust control. 4. Press the propel pedal to begin scrubbing. 5. Press the bottom of the side brush switch to stop and raise the side brush. NOTE: The Pre Sweep assembly will begin sweeping and the dust control system will start operating when the machine propels forward. 4. Press the bottom of Pre Sweep switch to shut off the Pre sweep system and dust control system. T ( ) 33

36 OPERATION EMPTY THE PRE SWEEP DEBRIS HOPPER FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and remove key. 4. Check the vacuum debris bag. Replace the vacuum debris bag if it is full or damaged. 1. Lift the Pre Sweep assembly cover and lock the cover open. 5. Unlock and lower the Pre Sweep cover. 2. Remove the debris hopper from the Pre Sweep assembly and empty the hopper. 3. Reinstall the debris hopper into the Pre Sweep assembly. 34 T ( )

37 OPERATION VACUUM WAND (OPTION) Use the vacuum wand to clean areas that are out of reach of the machine. 4. Twist the vacuum nozzle to the vacuum position and extend the handle to the desired length. WARNING: Flammable materials or reactive metals can cause an explosion or fire. Do not pick up. 1. Unsnap the vacuum wand lanyard from the solution tank. 5. Press the Vacuum fan/squeegee button to turn on the vacuum fan. The squeegee will completely lower. 2. Remove the vacuum wand / squeegee vacuum hose from the rear squeegee. 6. Vacuum the floor. 3. Insert the vacuum wand cap into the vacuum port in the vacuum wand. 7. When finished vacuuming, press the Vacuum fan/squeegee button to turn off the vacuum fan. The squeegee will raise. 8. Turn off the machine. T ( ) 35

38 OPERATION 9. Remove the vacuum wand cap from the vacuum port and return the vacuum nozzle to the storage position and the handle to the storage length. ADJUSTING BACKUP ALARM VOLUME (OPTION) FOR SAFETY: When using machine, follow site safety guidelines concerning backup alarms. The backup alarm volume can be adjusted from db(a). To adjust the volume, remove the backup alarm cover and turn the volume knob. Increase volume: Turn the knob clockwise. Decrease volume: Turn the knob counter clockwise. 10. Reinstall the vacuum wand / squeegee vacuum hose onto the rear squeegee. 11. Insert the vacuum hose into the vacuum hose recess in the recovery tank. 12. Snap the vacuum wand lanyard onto the solution tank to secure the vacuum wand / squeegee vacuum hose to the machine. 36 T ( )

39 OPERATION ROLLOUT BATTERY (OPTION) The rollout battery allows the operator a quick and easy way to remove and replace the batteries from the machine. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine and remove key. 1. Lift the operator seat and engage the seat support arm. 5. Rotate the rollout battery retainer handle toward the front of the battery compartment, lower the rollout battery retainer plate, and insert the retainer plate catch into the slot in the battery cart. NOTE: The retainer plate catch must be completely inserted into the slot in the battery cart to hold the battery retainer handle up and allow the batteries to be safely pulled from the battery compartment. 2. Open the battery compartment door. 3. Disconnect the machine connector from the batteries. 6. Step on the left side of floor lock to set the battery cart floor lock. 4. Push the battery cart to the operator side of the machine and align the battery cart with the battery compartment. T ( ) 37

40 OPERATION 7. If necessary, adjust the height of the battery cart rollers. The battery cart rollers must be level with the machine battery rollers. Adjust the height on both sides of the battery cart. 10. Raise the rollout battery retainer plate to release the battery cart from the machine. 11. Release the battery cart floor lock. 12. Pull the battery cart away from the machine. 13. Perform the previous steps in the reverse order to install batteries into the machine. REAR SQUEEGEE GUARD (OPTION) The rear squeegee protector helps protect the rear squeegee from being damaged. Raise battery cart rollers: Use a wrench to loosen the jam nut and turn the bolt clockwise. Retighten the jam nut. Lower battery cart rollers: Use a wrench to loosen the jam nut and turn the bolt counter clockwise. Retighten the jam nut. 8. Pull the battery case onto the battery cart. To engage the rear squeegee protector, pull the pin, lower the protector bar, and reinsert the pin. 9. Pull up on the handle to lower the cart battery stop bar. This will keep the batteries from rolling off the cart. 38 T (3 2011)

41 OPERATION SPRAY NOZZLE (OPTION) The spray nozzle is used to clean the machine and surrounding areas. The solution tank provides a water/solution supply for the spray nozzle. NOTE: DO NOT get water on electronic components when using the spray nozzle to clean the machine. FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. 4. When finished cleaning, gently pull the hose and allow the spray nozzle hose to retract back into the machine. NOTE: Continue holding onto the spray nozzle and control the hose while it is retracting back into the machine. The machine and / or the spray nozzle assembly could be damaged if the spray nozzle hose is released and allowed to rapidly retract into the machine. 5. Place the spray nozzle onto the hook. 1. Turn on the machine. 2. Press the top of the Spray nozzle switch to turn on the spray nozzle. The light on the switch will come on when the spray nozzle is turned on. 6. Press the bottom of the Spray nozzle switch to turn off the water supply. The light on the switch will turn off when the spray nozzle is turned off. 3. Pull the spray nozzle out from the back of the machine and clean as needed. T ( ) 39

42 OPERATION MACHINE TROUBLESHOOTING Problem Cause Remedy Trailing water poor or no water pickup Worn squeegee blades Rotate or replace squeegee blades Squeegee out of adjustment Adjust squeegee Vacuum hose clogged Flush vacuum hose Vacuum fan inlet filter dirty Clean inlet filter Debris caught on squeegee Remove debris from squeegee Vacuum hose to squeegee or recovery tank disconnected or Reconnect or replace vacuum hose damaged Tank cover not completely closed Check for obstructions Torn seals on recovery tank Replace seals Vacuum fan will not turn on Recovery tank full Drain recovery tank Foam filling recovery tank Empty recovery tank Use less or change detergent Use a defoamer Little or no solution flow to the Solution tank empty Fill solution tank floor Solution flow turned off Turn solution flow on Solution supply lines plugged Flush solution supply lines Solution solenoid clogged or Clean or replace stuck Poor scrubbing performance Debris caught on scrub brushes Remove debris from brushes Poor sweeping performance (Machines equipped with Pre Sweep option only) Improper detergent or brush used Worn scrub brush(es) Excessive brush pressure Uneven brush pressure Broken brush drive belts on cylindrical scrub head Low battery charge Brush bristles worn Debris caught in brush drive mechanism Hopper full Vacuum debris bag full Recirculation skirt damaged Wrong sweeping brush Main brush drive failure Contact TENNANT representative for recommendations Replace scrub brush(es) Reduce scrub brush down pressure Level scrub head Replace belts Charge batteries until the charger automatically turns off Replace brush Remove debris from the drive mechanism. Empty hopper Replace vacuum debris bag Replace recirculation skirt Contact TENNANT representative for recommendations Contact TENNANT service personnel 40 T (1 2011)

43 Problem Cause Remedy ES System does not operate ES button is turned off Turn on ES button OPERATION ES sensor in tank dirty not in Clean / reposition sensor correct position Clogged ES pump filter Clean ES filter Water level in recovery tank too Fill recovery tank about half full low Water level in solution tank too Fill solution tank low FaST System does not operate FaST button is turned off Turn on the FaST button FaST circuit breaker tripped Determine cause and reset the 15A circuit breaker button Clogged FaST PAK supply hose and/or connector Soak connector and hose in warm water and clean FaST PAK carton is empty or not connected Replace FaST PAK carton and/or connect supply hose FaST system is not primed To prime, operate the FaST solution system for 5 to 10 minutes Clogged flow control Remove and clean orifice/screen orifice/screen Faulty pump Contact Tennant representative Clogged filter screen Drain solution tank and clean filter screen Faulty detergent timer module Contact Tennant representative ec H2O Model: Warning and fault indicator light blinking red ec H2O Model: Warning and fault indicator light solid red Mineral deposit build up in module Clogged module Defective solution pump Flush module (See ec H2O MODULE FLUSH PROCEDURE) Contact Service Center Replace solution pump T (1 2011) 41

44 MAINTENANCE MAINTENANCE T ( )

45 MAINTENANCE MAINTENANCE CHART The table below indicates the Person Responsible for each procedure. O = Operator. T = Trained Personnel. Interval Person Resp. Key Description Procedure Daily O 1 Side and rear squeegees Check for damage and wear O 2 Main brushes Check for damage, wear, debris Lubricant/ Fluid No. of Service Points 3 2 O 3 Recovery tank Clean tank 1 O 3 Recovery tank (ES only) Clean ES filter 1 O 4 Solution tank (ES only) Clean solution supply filter 1 O 5 Vacuum fan inlet filter Clean 1 O 6 Cylindrical brushes only: Clean 1 Debris tray O 7 Pre Sweep side brushes Check for damage, wear, 2 debris O 10 Pre Sweep main bush Check for damage, wear, 1 debris O 8 Pre Sweep debris Clean 1 hopper O 20 Side brush Check for damage, wear, 1 debris O 20 Side brush squeegee Check for damage and 1 wear Weekly T 12 Battery cells Check electrolyte level DW 3 50 Hours 200 Hours T 11 Squeegee caster wheel Lubricate SPL 4 pivot points T 1 Side and rear squeegees Check deflection and leveling 6 O 13 Pre Sweep skirts and seals Check for damage and wear 4 O 2 Main brushes (cylindrical) Rotate brushes from front 2 to rear O 9 FaST/Solution filter screen Clean 1 T 12 Battery terminals and Check and clean 12 cables T 14 Cylindrical brush drive belts T 15 Pre Sweep brush drive belt Check for damage and wear Check for damage and wear T 17 Steering chain Lubricate, check tension, and check for damage and wear. 2 2 GL 1 T ( ) 43

46 MAINTENANCE The table below indicates the Person Responsible for each procedure. O = Operator. T = Trained Personnel. Interval 500 Hours 1000 Hours Person Resp. Key Description Procedure Lubricant/ Fluid No. of Service Points T 18 Vacuum fan motor(s) Check motor brushes 1 (2) O 21 Tires Check for damage and wear 3 T 14 Main brush motors Check motor brushes 2 (4) (Check every 100 hours after initial 1000 hour check) T 20 Side brush motor Check motor brushes 1 (Check every 100 hours after initial 1000 hour check) T 13 Pre Sweep main brush Check motor brushes 1 motor (Check every 100 hours after initial 1000 hour check) T 9 FaST injector filters Replace 1 LUBRICANT/FLUID DW... Distilled water. SPL... Special lubricant, Lubriplate EMB grease (Tennant part number ) GL... SAE 90 weight gear lubricant NOTE: More frequent maintenance intervals may be required in extremely dusty conditions. 44 T ( )

47 MAINTENANCE YELLOW TOUCH POINTS This machine features easy to find yellow touch points for simple service items. No tools are required to perform these maintenance operations, STEERING GEAR CHAIN The steering gear chain is located directly above the front tire. Check for damage or wear and lubricate the steering gear chain after every 200 hours. REAR SQUEEGEE CASTERS LUBRICATION Lubricate the rear squeegee caster pivot point on each squeegee caster after every 50 hours. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. STEERING CHAIN The steering chain is located on the steering column directly under the control panel. Check for damage or wear and lubricate the steering chain after every 200 hours. T ( ) 45

48 MAINTENANCE BATTERIES FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, set parking brake (if equipped), and remove key. The level should be slightly above the battery plates as shown before charging. Add distilled water if low. DO NOT OVERFILL. The electrolyte will expand and may overflow when charging. After charging, distilled water can be added up to about 3 mm (0.12 in) below the sight tubes. The lifetime of the batteries depends on their proper maintenance. To get the most life from the batteries; Before Charging After Charging Do not charge the batteries more than once a day and only after running the machine for a minimum of 15 minutes. Do not leave the batteries partially discharged for long period of time. Only charge the batteries in a well-ventilated area to prevent gas build up. Charge batteries in areas with ambient temperatures 27 C (80 F) or less. Allow the charger to complete charging the batteries before re-using the machine. Maintain the proper electrolyte levels of flooded (wet) batteries by checking levels weekly. CHECKING THE ELECTROLYTE LEVEL The flooded (wet) lead acid batteries require routine maintenance as described below. Check the battery electrolyte level weekly. NOTE: Do Not check the electrolyte level if the machine is equipped with the battery watering system. Proceed to the BATTERY WATERING SYSTEM (OPTION). NOTE: Make sure the battery caps are in place while charging. There may be a sulfur smell after charging batteries. This is normal. MAINTENANCE FREE BATTERIES Maintenance free batteries do not require watering. Cleaning and other routine maintenance is still required. CHECKING CONNECTIONS / CLEANING After every 200 hours of use check for loose battery connections and clean the surface of the batteries, including terminals and cable clamps, with a strong solution of baking soda and water. Replace any worn or damaged wires. Do not remove battery caps when cleaning batteries FOR SAFETY: When servicing machine, keep all metal objects off batteries. Avoid contact with battery acid. 46 T (1 2015)

49 MAINTENANCE CHARGING THE BATTERIES (OFF BOARD CHARGER) IMPORTANT: Before charging, make sure that the charger setting is properly set for the battery type. 5. Plug the charger connector into the remote battery charge connector. 1. Drive the machine to a flat, dry surface in a well ventilated area. 2. Stop the machine and turn the machine power off. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 3. Lift the operator seat open, engage the seat support bar, then remove the accessory box and tray. WARNING: Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. NOTE: If the charger FAULT CODE lights flash when the batteries are plugged into the charger, refer to the charger manufacturer manual for fault code definitions. 6. The Tennant charger will start automatically. When the batteries are fully charged, the Tennant charger will automatically turn off. NOTE: Make sure the batteries have the proper electrolyte level before charging. See CHECKING THE ELECTROLYTE LEVEL. 4. Plug the charger AC power supply cord into a properly grounded outlet. 7. After the charger has turned off, unplug the charger connector from the remote battery charge connector. ATTENTION: Do not disconnect the charger DC cord from the machine receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first. 8. Close the operator seat. T ( ) 47

50 MAINTENANCE CHARGING THE BATTERIES (ON BOARD CHARGER) IMPORTANT: Before charging, make sure that the charger setting is properly set for the battery type. 5. The on board charger will start charging the batteries. Once the charging cycle begins, the indicator lights will progress from red, yellow to green. When the green indicator light stays on, the charging cycle is done. 1. Drive the machine to a flat, dry surface in a well ventilated area. 2. Stop the machine and turn the machine power off. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 3. Lift the operator seat open, engage the seat support bar, then remove the accessory box and tray. If the charger detects a problem, the charger will display an error code (See ON BOARD BATTERY CHARGER ERROR CODES). 6. Unplug the on board battery charger from the wall outlet and neatly stow the cord inside the battery compartment. 7. Close the operator seat. NOTE: Make sure the batteries have the proper electrolyte level before charging. See CHECKING THE ELECTROLYTE LEVEL. 4. Plug the on board battery charger cord into a properly grounded wall outlet. WARNING: Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. NOTE: The machine will not operate when charging. 48 T ( )

51 MAINTENANCE ON BOARD BATTERY CHARGER ERROR CODES Display Code Fault Solution bat Loose or damaged battery cable. Check battery cable connection. Battery exceeded maximum voltage level. No action necessary. E01 Exceeded maximum battery voltage No action necessary. allowed. Interrupts charging cycle. E02 Safety thermostat exceeded maximum internal temperature. Interrupts charging cycle. Ensure the charger vents are not obstructed. Clear obstructions. E03 SCt Exceeded maximum time for charging phase, leaving the batteries undercharged due to a sulfated or faulty battery. Interrupts charging cycle. Safety timer exceeded maximum charging time. Interrupts charging cycle. Repeat the charging cycle. If the error code E03 reappears check battery or replace it. Replace battery. Srt Possible internal short circuit. Contact a Tennant service representative. T ( ) 49

52 MAINTENANCE ON BOARD CHARGER SETTINGS If the machine is equipped with the on board charger, the charger settings are properly set at the factory. If different batteries are put in the machine, the settings must be changed to match the new battery type before charging. Failure to properly set the charger will result in battery damage. To change the setting, unplug the charger and peel up the corner of the display label to access the switches. The charger cord must be unplugged when resetting. Refer to the battery label for the battery type. Contact the battery manufacturer if battery is not labeled. To verify the setting of the charger, connect the charger cord into an electrical outlet. The charger will display a sequence of the following codes (three digits + the code) when the cord is connected: A = Charging current U = Battery Voltage h = Charging time C = Charging ampere hours [Ah] E = Energy used [Kwh] GEL or Acd = Battery type for which the charger is currently set. Before charging make sure battery type matches the display: GEL=Sealed, Acd=WET (lead acid). Adjust the switches to the correct setting for the batteries. Lead Acid 240Ah: Press the arrow button to review the codes. Refer to the battery type code to determine the charger battery type setting. Lead Acid 360Ah: Gel: 50 T ( )

53 MAINTENANCE CHANGING THE ON BOARD BATTERY CHARGER FUSE FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. A 15 Amp fuse protects the on board charger. Follow the instructions below to replace a blown fuse. Never substitute a higher Amp rated fuse than specified. 1. Lift the operator seat open, engage the seat support bar, then remove the accessory box and tray. 5. Remove the hardware holding the on board battery charger onto the machine 2. Unplug the charger AC power supply cord from the wall outlet. WARNING: Electrical Hazard. Unplug charger before servicing machine. 3. Disconnect the battery cables from the batteries. 6. Carefully pull the on board charger out to access the fuse. 7. Remove the fuse cap and replace the fuse. FOR SAFETY: When servicing machine, disconnect battery connection before working on machine. 4. Remove the hardware holding the side panel to the machine and remove the side panel from the machine. 8. Reinstall the on board battery charger and side panel onto the machine. T ( ) 51

54 MAINTENANCE FLOW RITE BATTERY WATERING SYSTEM (OPTION) The optional Flow Rite battery watering system provides a safe and easy way to maintain the proper electrolyte levels in the batteries. 3. Connect the water supply hose to the fill regulator. NOTE: Water quality is important to maintain the life of the battery. Always use water that meets battery manufacturer requirements. NOTE: The water supply to the battery water system must always be 7.57 LPM (2 GPM) or more. Use the purger to confirm the water supply pressure. Refer to Flow Rite Operator Manual for additional information. Check the battery watering system hoses and connections for damage or wear after every 100 hours. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Lift the operator seat open and engage the seat support. 2. Fully charge batteries prior to using the battery watering system. Do not add water to batteries before charging, the electrolyte level will expand and may overflow when charging. See CHARGING THE BATTERIES (OFF BOARD CHARGER) or CHARGING THE BATTERIES (ON BOARD CHARGER). 4. Remove the dust cover from the battery fill tube and connect the fill regulator. 52 T ( )

55 MAINTENANCE 5. Turn on the water supply. The red balls inside the flow indicator will spin. The red balls stop spinning when the batteries are full. 6. Disconnect the battery fill tube from the fill regulator. 7. Turn off the water supply. 8. After adding water, replace the dust cap on the battery fill hose and return the fill regulator to the storage location for future use. T (1 2013) 53

56 MAINTENANCE HYDROLINK BATTERY WATERING SYSTEM (OPTION) The following instructions are for models equipped with the HydroLINK battery watering system option. 3. After charging batteries, check the battery electrolyte level indicators located on the battery covers. If the level indicator is white add water as described in the following instructions. If the level indicators are black the electrolyte is at the correct level, no water is required. The optional HydroLINK battery watering system provides a safe and easy way to maintain the proper electrolyte levels in your batteries. It is designed exclusively for Trojan wet/lead acid batteries. 4. Locate the battery fill hose coupler inside the battery compartment. Remove the dust cap and connect the hand pump hose. Check the battery watering system hoses and connections for damage or wear after every 100 hours. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Lift the operator seat open and engage the seat support. 2. Fully charge batteries prior to using the battery watering system. Do not add water to batteries before charging, the electrolyte level will expand and may overflow when charging. See CHARGING THE BATTERIES (OFF BOARD CHARGER) or CHARGING THE BATTERIES (ON BOARD CHARGER). 5. Submerge the other end of the hand pump hose into a bottle of distilled water. Distilled Water 54 T ( )

57 MAINTENANCE 6. Squeeze the bulb on the hand pump hose until firm. The level indicators will turn black when full. 7. After adding water, replace the dust cap on the battery fill hose and store the hand pump hose inside the machine s battery compartment for future use. T ( ) 55

58 MAINTENANCE CIRCUIT BREAKERS Circuit breakers are resettable electrical circuit protection devices designed to stop the flow of current in the event of a circuit overload. Once a circuit breaker is tripped, reset it manually by pressing the reset button after the breaker has cooled down. Circuit breakers 1 through 10 are located in the front of the battery compartment. Circuit breakers 11 through 19 are located on the electrical panel. If the overload that caused the circuit breaker to trip is still present, the circuit breaker will continue to stop current flow until the problem is corrected. The chart below shows the circuit breakers and the electrical components they protect. Circuit Breaker Rating Circuit Protected CB1 2.5 A Start CB2 2.5 A Key switch CB3 2.5 A Sweep controls (Option) CB4 2.5 A Main water, FaST, ES, Horn CB5 2.5 A Detergent meter (Option) CB6 2.5 A Side brush (Option) CB7 15 A FaST./ ES pump (Option) CB8 20 A Sweep brushes (Option) CB9 2.5 A ec H2O (Option) CB A ec H2O pump (Option) CB11 15 A Lights (Option) CB A Headlight / Tail lights (Option) CB A Overhead guard warning light (Option) CB14 15 A Spray Nozzle (Option) CB A Warning lights (Option) CB16 15 A Pre Sweep (Option) CB17 Open Extra for Specials CB18 Open Extra for Specials CB19 25 A Sweep vacuum fans (Option) CB20 25 A Reverse alarm light (Option) ELECTRIC MOTORS Circuit breaker 20 is located inside the optional light assembly mounted on top of the recovery tank. Inspect the carbon brushes on the vacuum fan motor after every 500 hours of operation. Inspect the carbon brushes on the main brush motors, Pre Sweep main brush motor, and side brush motors after the first 1000 hours of operation and every 100 hours after the initial check.refer to the table below for carbon brush inspection intervals. Carbon Brush Inspection Hours Main Brush Motors 1000* Pre Sweep Main Brush Motors 1000* Side Brush Motor (Option) 1000* Vacuum Motor 500 *Inspect carbon brushes every 100 hours after the initial 1000 hour change. 56 T ( )

59 MAINTENANCE SCRUB BRUSHES 3. Open the left side squeegee support door. The machine can be equipped with either disk or cylindrical scrub brushes. Check scrub brushes daily for wire or string tangled around the brush or brush drive hub. Also check brushes or pads for damage and wear. DISK BRUSHES AND PADS Replace the pads when they no longer clean effectively. Replace the brushes when they no longer clean effectively or when the bristles are worn down to the yellow indicators. 4. Turn the brushes until the spring handles are visible. Cleaning pads must be placed on pad drivers before they are ready to use. The cleaning pad is held in place with a center disk. Both sides of the pad can be used for scrubbing. Turn the pad over to use the other side. Cleaning pads need to be cleaned immediately after use with soap and water. Do not wash the pads with a pressure washer. Hang pads, or lay pads flat to dry. 5. Squeeze the spring handles and let the brushes drop to the floor. Remove the brush from under the scrub head. NOTE: Always replace brushes and pads in sets. Otherwise one brush or pad will be more aggressive than the other. REPLACING DISK BRUSHES OR PAD DRIVERS 1. Raise the scrub head. 2. Turn off the machine. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. T ( ) 57

60 MAINTENANCE 6. Set the brush spring open on the new brush to make the brush installation easier. REPLACING DISK SCRUB PADS 1. Remove the pad driver from the machine. 2. Squeeze the spring clip together and remove the center disk from the pad driver. 7. Push the new brush under the scrub head, align the brush drive socket with the brush drive hub, and lift the brush up onto the brush drive hub until the brush locks onto the hub. 3. Remove the scrub pad from the pad driver. 8. Ensure the brush is securely mounted on the brush drive hub. 9. Close and secure the left side squeegee assembly. 10.Repeat procedure for the other brush. 4. Flip or replace the scrub pad. Center the scrub pad on the pad driver and reinstall the center disk to secure the pad in place on the pad driver. 5. Reinstall the pad driver onto the machine. 58 T ( )

61 MAINTENANCE CYLINDRICAL BRUSHES Rotate the brushes from front-to-rear after every 50 hours of operation. 4. Remove the brush from the scrub head Replace the brushes when they no longer clean effectively. NOTE: Replace worn brushes in pairs. Scrubbing with brushes of unequal bristle length will result in diminished scrubbing performance. REPLACING CYLINDRICAL SCRUB BRUSHES FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Open the side squeegee support door. 2. Lift the idler plate retainer handle and unhook the retainer ring from the idler plate hook. 5. Position the brush with the double row end towards the scrub head opening. Guide the new brush onto the drive hub. 6. If rotating the brushes, always rotate the front with the back so that they wear evenly. They may be rotated end for end as well. A B B A Before After 3. Remove the idler plate from the scrub head. 7. Reinstall the idler plate onto the scrub head and secure the idler plate into place with the idler plate retainer. 8. Repeat for the other brush on the other side of the scrub head. NOTE: Do not switch the left or right idler plates or the brushes will need to be readjusted by trained personnel. T ( ) 59

62 MAINTENANCE SIDE BRUSH (OPTION) 4. Squeeze the spring handles and let the side brush drop to the floor. Check the side brush daily for wear or damage. Remove any tangled string or wire from the side brush or side brush drive hub. REPLACING THE SIDE BRUSH Replace the pads when they no longer clean effectively. Replace the brushes when they no longer clean effectively or when the bristles are worn down to the yellow indicators. 1. Start the machine and press the side brush switch. 2. Shut off the machine after the side brush rotates from under the side guard, but before the side brush assembly lowers to the floor. 5. Remove the side brush from under the side brush assembly. 6. Set the brush spring open on the new brush to make the brush installation easier. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 3. Remove the knobs holding the side brush squeegee assembly to the machine and remove the squeegee assembly from the machine. 7. Place the new side brush underneath the side brush assembly and lift the side brush up onto the side brush hub until the brush locks onto the hub. 8. Reinstall the side brush squeegee assembly onto the side brush assembly. 60 T ( )

63 MAINTENANCE PRE SWEEP BRUSHES 4. Reach into the center of the brush and pull the cotter pin from the hub assembly. The Pre Sweep assembly is equipped with disk side brushes and a cylindrical main brush. Check the brushes daily for wire or string tangled around the brush or brush drive hub. Check the brushes daily for damage and wear. REPLACING THE PRE SWEEP DISK BRUSHES Replace the brushes when they no longer clean effectively. 1. Turn on the machine. 2. Press the bottom of the Pre Sweep switch to raise the Pre Sweep assembly and stop sweeping. 5. Remove the side brush from under the Pre Sweep assembly. 3. Turn off the machine. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 6. Install the new side brush onto the Pre Sweep side brush assembly. T ( ) 61

64 MAINTENANCE REPLACING THE PRE SWEEP CYLINDRICAL BRUSH Replace the brush when it no longer cleans effectively. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 5. Remove the three knobs holding the Pre Sweep side skirt and side skirt plate to the Pre Sweep assembly. 1. Turn off the machine. 2. Open the Pre Sweep assembly cover and lock the cover open. 3. Loosen and remove the left brush arm knob. 6. Remove the side skirt plate and side skirt from the Pre Sweep assembly. 4. Remove the left brush arm. 7. Remove the cylindrical brush and replace with a new brush. 8. Guide the slotted end of the new brush onto the drive hub. 9. Reinstall the side skirt, side skirt plate, and left brush arm. 62 T ( )

65 MAINTENANCE FaST SYSTEM REPLACING THE FaST PAK CARTON FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 1. Lift the operator seat open and engage the seat support bar. 2. Squeeze the button on the FaST supply hose connector, then pull the empty FaST PAK carton out from the compartment and discard. 5. Connect the FaST supply hose to the FaST PAK hose connector. 6. Scrub with the FaST system for a few minutes to allow the detergent to reach maximum foaming. CLEANING THE FaST SUPPLY HOSE CONNECTOR Soak the connector in warm water if detergent buildup is visible. When a FaST PAK carton is not installed, store the supply hose connector on the storing plug to prevent the hose from clogging. REPLACING THE FaST INJECTOR FILTERS Replace the FaST injector filters after every 1000 hours of operation. Empty the solution tank before replacing the filters. 3. Remove the perforated knock outs from the new FaST PAK carton. DO NOT remove the bag from the carton. Pull the hose connector from the bottom of the bag and remove the hose cap from the connector. NOTE: The FaST PAK Floor Cleaning Concentrate is specially designed for use with the FaST system scrubbing application. NEVER use a substitute. Other cleaning solutions may cause FaST system failure. 4. Slide the FaST PAK carton into the FaST PAK bracket. T ( ) 63

66 MAINTENANCE ec H2O MODULE FLUSH PROCEDURE 4. Disconnect the outlet hose from the hose connected to the ec H2O manifold. This procedure is only required when an alarm sounds and the ec H2O system indicator light begins to blink. FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. 1. Lift the operator seat open and engage the seat support bar. 2. Remove the ec H2O compartment cover. 5. Connect the drain hose to the ec H2O manifold hose disconnected from the outlet hose in the previous step. 3. Remove the drain hose from the ec H2O compartment. 6. Place the drain hose into a empty container. 7. Pour 2 gallons (7.6 liters) of white or rice vinegar into the solution tank. 64 T ( )

67 MAINTENANCE 8. Turn the key to the on ( I ) position. 9. Press and release the ec H2O module flush switch to start the flush cycle. NOTE: The module will automatically shut off when the flush cycle is complete (approximately 7 minutes). The module must run the full 7 minute cycle in order to reset the system indicator light and alarm. 10. Pour 2 gallons (7.6 liters) of cool clean water into the solution tank. 11. Press and release the flush switch to rinse any remaining vinegar from the module. After 1 2 minutes, press the flush switch to turn off the module. 12. Disconnect the drain hose from the ec H2O manifold hose. 13. Reconnect the outlet hose to the the scrub head to the ec H2O manifold hose. 14. Place the drain hose back into the ec H2O compartment. 15. Reinstall the ec H2O compartment cover. 16. Close the operator seat cover. T ( ) 65

68 MAINTENANCE SQUEEGEE BLADES 3. Loosen both squeegee mounting handles. Check the squeegee blades for damage and wear daily. When the blades become worn, rotate the blades end for end or top to bottom to a new wiping edge. Replace blades when all edges are worn. Check the deflection of the squeegee blades daily or when scrubbing a different type of surface. Check the leveling of the rear squeegee every 50 hours of operation. REPLACING (OR ROTATING) THE REAR SQUEEGEE BLADES 1. Lower the scrub head. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 2. Disconnect the vacuum hose from the rear squeegee assembly. 4. Pull the rear squeegee assembly from the machine. 66 T ( )

69 MAINTENANCE 5. Loosen the retainer latch and remove the retainer from the squeegee assembly. 8. Remove the inner frame from the outer frame. 6. Remove the squeegee from the squeegee assembly. 9. Remove the squeegee from the outer frame. 7. Slide both retainers out away from the squeegee assembly. 10. Install the rotated or new squeegee blade into the outer frame. Be sure the squeegee is completely slid down onto each tab on the outer frame. T ( ) 67

70 MAINTENANCE 11. Install the inner frame over the squeegee and onto the outer frame. Be sure the inner frame is tight against the top of the outer frame. 14. Insert the hinge end of the retainer into the hooks in the inner frame. 12. Slide both retainers into the squeegee assembly. 15. Install the retainer along the rest of the squeegee assembly and fasten the latch onto the other end of the squeegee assembly. 13. Place the rotated or new squeegee blade onto the inner frame. Be sure the squeegee is securely attached on each tab on the inner frame. 68 T ( )

71 MAINTENANCE LEVELING THE REAR SQUEEGEE Leveling the squeegee ensures the entire length of the squeegee blade is in even contact with the surface being scrubbed. Perform this adjustment on an even and level floor. 1. Lower the squeegee and drive the machine several meters (feet) forward and slowly bring the machine to a stop. 5. Turn the squeegee tilt adjust knob counter-clockwise to decrease the deflection at the ends of the squeegee blade. Turn the squeegee tilt adjust knob clockwise to increase the deflection at the ends of the squeegee blade. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 2. Check the squeegee deflection over the full length of the squeegee blade. 3. If the deflection is not the same over the full length of the blade, use the tilt adjust knob to make adjustments. DO NOT disconnect the vacuum hose from the squeegee frame when leveling squeegee. 4. To adjust the squeegee leveling, loosen the tilt lock knob. 6. Tighten the tilt lock knob. 7. Drive the machine forward with the squeegee down to recheck the squeegee blade deflection if adjustments were made. 8. Readjust the squeegee blade deflection if necessary. T ( ) 69

72 MAINTENANCE ADJUSTING THE REAR SQUEEGEE BLADE DEFLECTION Deflection is the amount of curl the overall squeegee blade has when the machine moves forward. The best deflection is when the squeegee wipes the floor dry with a minimal amount of deflection. 3. To adjust the overall squeegee blade deflection, loosen the lock knob. NOTE: Make sure the squeegee is level before adjusting the deflection. See LEVELING THE REAR SQUEEGEE. 1. Lower the squeegee and drive the machine several meters (feet) forward and slowly bring the machine to a stop. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 2. Look at the amount of deflection or curl of the squeegee blade. The correct amount of deflection is 12 mm (0.50 in) for scrubbing smooth floors and 15 mm (0.62 in) for rough floors. 4. Turn the adjustment knobs counterclockwise to increase deflection or clockwise to decrease deflection. 5. Retighten the lock knob. 6. Drive the machine forward again to recheck the squeegee blade deflection. 7. Readjust the squeegee blade deflection if necessary. 70 T ( )

73 MAINTENANCE REPLACING OR ROTATING THE SIDE SQUEEGEE BLADES 1. If necessary, raise the scrub head. 5. Remove the squeegee from the side squeegee assembly. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 2. Open the side squeegee support door. 6. Install the rotated or new rear squeegee blade onto the side squeegee assembly. 7. Hook the retaining band onto the side squeegee assembly. 3. Unhook the retaining band latch from the side squeegee assembly. 8. Fasten the retaining band latch onto the side squeegee assembly. 4. Remove the retaining band from the side squeegee assembly. 9. Repeat for the side squeegee on the other side of the scrub head. T ( ) 71

74 MAINTENANCE REPLACING OR ROTATING THE SIDE BRUSH SQUEEGEE BLADES (OPTION) Check the side brush squeegee blade for damage and wear daily. Replace or rotate the blade if the leading edge is torn or worn half-way through the thickness of the blade. 3. Remove the knobs holding the side brush squeegee assembly to the machine and remove the squeegee assembly. 1. Start the machine and press the side brush switch. 2. Shut off the machine after the side brush rotates from under the side guard, but before the side brush assembly lowers to the floor. FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. 4. Loosen the retaining band latch. 72 T ( )

75 MAINTENANCE 5. Remove the squeegee blades and retainer from the squeegee frame. NOTE: Observe which squeegee slots were installed on the squeegee frame before removing the squeegee. NOTE: The squeegee blade(s) have two sets of slots for adjusting the squeegee blade deflection. Install / reinstall squeegees so the deflection is approximately 12 mm (0.50 in) for smooth floors and 15 mm (0.62 in) for rough floors. T ( ) 73

76 MAINTENANCE 6. Install the rotated / new squeegee blades and retainer onto the side brush assembly. 7. Fasten the side brush retaining band latch. 8. Reinstall the side brush squeegee assembly onto the side brush assembly. 74 T ( )

77 MAINTENANCE SKIRTS AND SEALS FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. PRE SWEEP REAR SKIRT (OPTION) The Pre Sweep rear skirt is located behind the recirculation skirt and main sweeping brush. PRE SWEEP SIDE SKIRTS (OPTION) The side skirts are located on both sides of the Pre Sweep assembly. The side skirts should be just touching the floor. Check the skirt for damage and wear after every 50 hours of operation. Check the skirts for damage and wear after every 50 hours of operation. PRE SWEEP RECIRCULATION SKIRT (OPTION) The Pre Sweep recirculation skirt is located behind the main sweeping brush. Check the skirt for damage and wear after every 50 hours of operation. T ( ) 75

78 MAINTENANCE BELTS FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. PRE SWEEP BRUSH DRIVE BELT (OPTION) The Pre Sweep brush drive belt is located inside the Pre Sweep assembly on the right side of the cylindrical brush. Check the belt for damage and wear after every 200 hours of operation. CYLINDRICAL BRUSH DRIVE BELTS The brush drive belts are located on the cylindrical brush scrub head. Check the belts for damage and wear after every 200 hours of operation. TIRES FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. The machine has three solid rubber tires: one in front, and two in the rear of the machine. Check tires for damage and wear after every 500 hours of operation. 76 T ( )

79 MAINTENANCE PUSHING, TOWING, AND TRANSPORTING THE MACHINE PUSHING OR TOWING THE MACHINE If the machine becomes disabled, it can be pushed or towed from the front or rear. 3. If the loading surface is not horizontal or is higher than 380 mm (15 in) from the ground, use a winch to load machine. If the loading surface is horizontal AND is 380 mm (15 in) or less from the ground, the machine may be driven onto the truck or trailer. The parking brake must be disabled before towing or pushing the machine. To disable the brake, insert the tip of a small screw driver between the electronic brake lever and the hub. The machine can move freely when the parking brake is disabled. FOR SAFETY: When loading machine onto truck or trailer, use winch. Do not drive the machine onto the truck or trailer unless the loading surface is horizontal AND is 380 mm (15 in) or less from the ground. Only push or tow the machine for a very short distance and do not exceed 3.2 kp/h (2 mph). It is NOT intended to be pushed or towed for a long distance or at a high speed. 4. To winch the machine onto the truck or trailer, attach the winching chains to the stabilizer legs. ATTENTION! Do not push or tow machine for a long distance or damage may occur to the propelling system. Immediately after pushing the machine, remove the screw driver from between the electronic brake lever and the hub. NEVER operate the machine with the parking brake disabled. FOR SAFETY: Do not operate machine with brake disabled. TRANSPORTING THE MACHINE 1. Raise the squeegee, scrub head, and brushes. FOR SAFETY: When loading/unloading machine onto/off truck or trailer, drain tanks before loading machine. 5. Position the machine onto the truck or trailer as far as possible. If the machine starts to veer off the center line of the truck or trailer, stop and turn the steering wheel to center the machine. 2. Position the machine at the loading edge of the truck or trailer. T ( ) 77

80 MAINTENANCE 6. Lower the scrub head and block the,machine tires. Tie down the machine to the truck or trailer before transporting.. FOR SAFETY: When loading/unloading machine onto/off truck or trailer, lower scrub head and squeegee before tying down machine. The front tie down locations are the stabilizer legs. 7. If the loading surface is not horizontal or is higher than 380 mm (15 in) from the ground, use a winch to unload machine. If the loading surface is horizontal AND is 380 mm (15 in) or less from the ground, the machine may be driven off the truck or trailer. FOR SAFETY: When unloading machine off truck or trailer, use winch. Do not drive the machine off the truck or trailer unless the loading surface is horizontal AND 380 mm (15 in) or less from the ground. The rear tie-down locations are the holes in the frame. 78 T ( )

81 MAINTENANCE MACHINE JACKING STORAGE INFORMATION FOR SAFETY: Before leaving or servicing machine, stop on level surface, turn off machine, and remove key. Empty the recovery and solution tanks before jacking the machine. The following steps should be taken when storing the machine for extended periods of time. 1. Charge the batteries before storing machine to prolong the life of the batteries. Recharge batteries once a month. 2. Disconnect batteries before storing. 3. Thoroughly drain and rinse the solution and recovery tanks. 4. Store the machine in a dry area with the squeegee and scrub head in the up position. ATTENTION: Do not expose machine to rain, store indoors. 5. Open the recovery tank cover to promote air circulation. 6. If storing machine in freezing temperatures, proceed to FREEZE PROTECTION. NOTE: To prevent potential machine damage store machine in a rodent and insect free environment. FOR SAFETY: When servicing machine, block machine tires before jacking machine up. Use a hoist or jack that will support the weight of the machine. Jack machine up at designated locations only. Support machine with jack stands. T ( ) 79

82 MAINTENANCE FREEZE PROTECTION (MACHINES WITHOUT OPTIONAL ec H2O SYSTEM) FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. 7. Turn on the machine 8. Press the 1 STEP button. 1. Machines equipped with FaST: Remove the FaST PAK. 2. Completely drain the solution tank and recovery tank. 3. Disconnect the hose from the solenoid valve inlet port located on the bottom of the frame and allow all remaining solution to drain from the system. 9. Repeatedly press the Solution increase button (+) until the solution flow is at the highest setting. 4. Use between kpa (2 4 psi) of compressed air to blow remaining solution from the disconnected hose. 5. Reconnect the hose to the solenoid valve inlet port. 6. Pour 7.6 L (2 gal) of Propylene Glycol Based / Recreational Vehicle (RV) antifreeze into the solution tank. 10. Drive the machine to circulate the RV antifreeze completely through the system. 11. Press the 1 STEP button to turn off the system. 12. Machines equipped with the optional spray nozzle only: Operate the wand for a few seconds to protect the pump. 13. Turn off the machine. 14. The remaining RV antifreeze does not need to be drained from the solution tank. 80 T ( )

83 MAINTENANCE PREPARING THE MACHINE FOR OPERATION (MACHINES WITHOUT OPTIONAL ec H2O SYSTEM) All Propylene Glycol Based / Recreational Vehicle (RV) Antifreeze must be completely cleaned from the scrubbing system before the machine can be used for scrubbing. 6. Repeatedly press the Solution increase button (+) until the solution flow is at the highest setting. FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. 1. Completely drain all Propylene Glycol Based / Recreational Vehicle (RV) antifreeze from the solution tank. 2. Rinse out the solution tank. Refer to DRAINING AND CLEANING THE SOLUTION TANK in the OPERATION section for instructions how to clean the solution tank. 3. Pour 11.4 L (3 gal) of cool clean water into the solution tank. 7. Drive the machine to circulate the clean water completely through the system to clean out the RV antifreeze. 8. Press the 1 STEP button to turn off the system. 9. Machines equipped with the optional spray nozzle only: Operate the wand for a few seconds to clean the RV antifreeze from the pump. 10. Turn off the machine. 11. The remaining water does not need to be drained from the solution tank. 4. Turn on the machine 5. Press the 1 STEP button. T ( ) 81

84 MAINTENANCE FREEZE PROTECTION (MACHINES WITH OPTIONAL ec H2O SYSTEM) 1. Completely drain the solution tank and recovery tank. 7. Remove the drain hose from the ec H2O compartment. 2. Disconnect the hose from the solenoid valve inlet port located on the bottom of the frame and allow all remaining solution to drain from the system. 8. Disconnect the outlet hose to the scrub head from the ec H2O manifold hose. 3. Use between kpa (2 4 psi) of compressed air to blow remaining solution from the disconnected hose. 4. Reconnect the hose to the solenoid valve inlet port. 5. Lift the operator seat open and engage the seat support bar. 6. Remove the ec H2O compartment cover. 9. Connect the drain hose to the ec H2O manifold hose disconnected from the outlet hose in the previous step. 82 T ( )