TITAN SYSTEM ENGINEERING DATA SHEET TITAN HXS

Transcription

1 This document and specifications are the property of REsys and shall not be reproduced or disseminated other than for recipients use for internal evaluation of REsys prices and product specifications. TITAN SYSTEM ENGINEERING DATA SHEET TITAN HXS Page # 1

2 Page # 2 ETS TITAN 10 GPM RECYCLE/REVERSE OSMOSIS DI WATER SYSTEM: Textured gray polypropylene cabinet construction. Capable of generating 10 gpm of DI quality water (recommended filtration media required) gallon ( liter) integrated storage tank for zero discharge installations. 2.0 HP stainless steel multistage circulation pump. Ultra-violet lamp assembly to treat biological organisms. 6 stainless steel bag filter assembly (5 micron). Flow meter (0 10 gpm). Pressure gauges and a run time indicator. 3-range resistivity meter (time delayed low limit alarm shutdown). High level protection with overflow weir and audible alarm. Automatic water make-up to compensate for evaporative losses in the cleaner(s). Control system: On/off main power switch, digital run timer indicator, 7-day programmable timer, test push-button switch for high level alarm circuit, switch to go from filtration drive to water recycle, lights indicating filtration drive or recycle operation mode, a power On light, audio On/Off switch, operation during high level On/Off switch, and a resistivity meter with low water quality delayed alarm shut down with manual reset. Total weight dry: 950 lbs. (418.5 kg). Footprint: 60 x 60 x 56 (152.4 cm x cm x cm). Single point utilities drop ( VAC, 3 phase only). Stand-alone heater required for all other voltages. - Standard voltage 480 VAC, 3 phase, 60 Hz 45 Amps (including 30 kw in-line heater). - Specify w/order 380 VAC, 3 phase, 60 Hz 55 Amps (including 30 kw in-line heater). - Specify w/order VAC, 3 phase, 60 Hz 10 Amps (not including 30 kw in-line booster heater, see stand alone 30 kw in-line heater for power requirements). Utility connections: - Electrical power drop - Waste in from cleaner (2) 1.00 FNPT - DI water to cleaner (1) 1.50 FNPT - Make up DI water input (1) 1.50 FNPT - To recycle media (1) 1.50 FNPT - From recycle media (1) 1.50 FNPT - Concentrate to drain (1) 0.75" FNPT - Over flow weir (1) 1.50: FNPT SPILL CONTAINMENT TRAY: Tank storage tray for (6) 2.5 ft. 3 ion exchange tanks. Textured gray polypropylene construction Quick disconnect fittings and hoses to couple the recycle media tanks to the TITAN Central Recovery Unit. Total weight: 55 lbs. (25.9 kg). Footprint: 30 x 45 x 2.5 (76.2 cm x cm x 6.35 cm)

3 OPTIONS: MODEL 104 TRANSFER STATION: Transfer water from the in-line cleaner to the Model TITAN Central Recovery Unit. 40 gallon (151.4 liter) textured gray polypropylene holding tank. Pressure gauge. High flow cartridge filter assembly (5 micron). ¾ HP stainless steel circulation pump with pumping rate adjustment valve. Control system consists of On/Off main power switch and an operating light. Total weight dry: 125 lbs. (56.6 kg). Footprint: 27 x 27 x 35 (68.6 cm x 68.6 cm x 88.9 cm) Single point electrical drop: - Standard voltage 480 VAC, 3 Phase, 60 Hz. 4 Amps - Specify w/order 380 VAC, 3 Phase, 50 Hz 5 Amps - Specify w/order VAC, 3 Phase, 60 Hz 8 Amps Utility connections: - Electrical power drop - Waste in from cleaner (1) 1.50 FNPT - Overflow weir (1) 1.50 FNPT - Water out to CRU (1) 1.00 FNPT OPEN 10 TANK MEDIA RACK: Textured gray polypropylene Provides storage space for (10) 2.5 ft. 3 ion exchange tanks. Provides interconnects and quick disconnects for the ion exchange tanks. Y-strainer on output for removal of suspended solids. A sample port after the 1 st HMR tank. Valve switching between the right and left banks, while the system is running. Drip tray for secondary spill containment. Footprint 38 x 78 x 24 (96.5 cm x 198 cm x 61 cm) Utility connections - Input from the CRU (1) 1.00 FNPT - Output to CRU (1) 1.00 FNPT - Output to drain (1) 1.00 FNPT Page # 3

4 ENCLOSED 10 TANK MEDIA RACK: Textured gray polypropylene Plexi-glass doors. Provides storage space for (10) 2.5 ft. 3 ion exchange tanks (tanks are fully enclosed). Provides interconnects and quick disconnects for the ion exchange tanks. Y-strainer on output for removal of suspended solids. Backflush valve for the Carbon and HMR tanks. A sample port after the 1 st HMR tank. Valve switching between the right and left banks, while the system is running. Drip tray for secondary spill containment. Footprint 38 x 78 x 68 (96.5 cm x 198 cm x cm) Utility connections - Input from the CRU (1) 1.00 FNPT - Output to CRU (1) 1.00 FNPT - Output to drain (1) 1.00 FNPT HXS (HEAT EXCHANGE / HEATING SYSTEM): Photo on Cover Textured gray polypropylene cabinet construction. 60 gallon ( liter) integrated storage tank for zero discharge installations. Auto-adjust: Automatically adjusts pumping rate to accommodate variable incoming flow rates. ¾ HP stainless steel multistage circulation pump. High flow cartridge filter assembly (5 micron). Pressure gauges and a run time indicator. High level protection with overflow weir and audible alarm. Stainless steel heat exchanger. 30 kw in-line DI water heater (after the filtration media to achieve final rinse temperatures above 140 F). - Pre-installed on the 203 ( VAC, 3 phase only). Stand-alone heater required for all other voltages. Page # 4

5 - Control system: On/off main power switch, light indicating power ON, controller with temperature set point adjustment, output temperature display, high temperature limit shut off light and reset button. - Maximum operating pressure: 120 psi. (828 kpa). - Pressure relief valve pre-installed. Control system: On/off main power switch, digital run timer indicator, test push-button switch for high level alarm circuit, a power On light, audio On/Off switch, operation during high level On/Off switch. Total weight dry: 120 lbs. (54.4 kg). Footprint: 30 x 34 x 44 (76.2 cm x cm x cm). Single point utility drop ( VAC, 3 phase only). Stand-alone heater required for all other voltages. - Standard voltage 480 VAC, 3 phase, 60 Hz 45 Amps (including 30 kw in-line heater). - Specify w/order 380 VAC, 3 phase, 60 Hz 55 Amps (including 30 kw in-line heater). - Specify w/order VAC, 3 phase, 60 Hz 10 Amps (not including 30 kw in-line booster heater, see stand alone 30 kw in-line heater for power requirements). Utility connections: - Electrical power drop - Waste in from cleaner (2) 1.50 FNPT - Heated water to cleaner (1) 1.00 FNPT - Input source water (1) 0.75 FNPT - Output to drain (1) 1.00 FNPT - Over flow weir (1) 1.50 FNPT ETS STANDARD FEATURES: Photo on Cover Textured gray polypropylene cabinet and tank: 200-gallon capacity. 1micron 12 stainless steel filter housing (0 10) gpm flow meter High level protection with overflow weir and audible alarm. 1.0 HP stainless steel multistage high-pressure pump to force the drain bound water through particulate filters and HMR tanks. Run time indicator. Pre-filter pressure gauges. ph monitor and probe Detergent injection pump Timer shutdown to ensure HMR tank routine leadtrak testing Mixing apparatus Automatic hands off operation Total weight dry: 340 lbs. (154.3 kg). Footprint 59 x 48 x 56 (152.4 cm x cm x cm). Single point utility drop: - Standard voltage 460 VAC, 3 phase, 60 Hz 10 amps. - Specify w/order 380 VAC, 3 phase, 50 Hz 12 amps. Utility connections: - Single point electrical power drop - Output to drain (1) 1.00 FNPT Page # 5

6 - Overflow weir (1) 1.50 FNPT - Input from stencil cleaner (1) 1.00 FNPT FILTRATION MEDIA (Select one of the recycle media packages; dual or mixed bed technology): Recycle media, 2.5 ft. 3, dual bed (HMR, GAC, CA, AN) Recycle media, 2.5 ft. 3, dual bed w/polisher (HMR, GAC, CA, AN, MB) Recycle media, 2.5 ft. 3, mixed bed (HMR, GAC, MB, MB) Drain media, 2.5 ft. 3, (HMR,HMR) Mixed bed, 2.5 ft. 3, (MB) - HMR Heavy metals removal; pre-filter heavy metals to protect downstream ion exchange tanks. - GAC Granular activated carbon; pre-filter organic material to protect downstream ion exchange tanks. - CA Cation; Positive ion removal - AN Anion; Negative ion removal - MB Mixed bed; Combination of Cation and Anion resins for ultra pure DI water. INSTALLATION KIT: Provides CPVC plumbing and fittings for complete plumbing connections between a cleaning system and the Model TITAN Recycle System. Kit includes 1.0 CPVC schedule 80 piping and fittings to complete field plumbing. Note: selection is based on linear feet of piping from the cleaner to the Model TITAN foot installation kit foot installation kit Notes: Two (2) complete sets of media are recommended. D2 D1 FR R Rinse C/I R.Wash PW HXS Heated DIW ater Bound for FR Main Drain DITanks Make up Water Water Sofner Valves to DivertCleaner Effluent to Titan for Recycle or to ETS for drain release TITA N Heated DIW ater Bound for SC Stencil EDS: TITAN Cleaner Rev.2 Page # 6 Incom ing Tap W ater Cleaner E fluent DIWater Drain Media Tanks ETS Drain

7 TITAN (10 GPM Reverse Osmosis / Recycle System) HXS (Heat Exchange / Heating System) Page # 7

8 ETS (Effluent Treatment System) Page # 8