NANO HIPPO 50WH Air Purifier

Transcription

1 NANO HIPPO 50WH Air Purifier FIMACO SDN. BHD.

2

3 Contents Contents 1 Important Safeguards 2 Introduction 4 First installation 9 Using method 11 Maintenance and cleaning 17 Replacing air filter 19 Trouble shooting 21 1

4 Important Safeguards Please read this user manual carefully before using the appliance and save it for future reference. Danger Do not let water or any other liquid or flammable detergent enter the unit to avoid electric shock and / or a fire hazard. Do not clean the appliance with water or any other liquid or (flammable) detergent to avoid electric shock and/ or a fire hazard. Check if the voltage indicated on the rating label corresponds to the local mains voltage before you connect the appliance. If the mains cord is damaged, you must contact our company or a service center authorized by us or similarly qualified persons to replace it in order to avoid a hazard. Do not use the appliance if the plug, the mains cord or the appliance itself is damaged. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision for their safety. Children should be supervised to ensure that they do not play with the appliance. Do not block the air inlet and outlet, e.g. by placing items on the air outlet or in front of the air inlet. warning This appliance is not a substitute for the proper ventilation, regular vacuum cleaning or use of an extractor hood or fan while cooking. If the wall socket used to power the appliance has poor connections, the plugof the appliance becomes hot. Make sure you plug the appliance into a properly connected wall socket. Always place and use the appliance on a dry, stable, level and horizontal surface. Leave at least 20cm free space behind and on both sides of the appliance and leave at least 30cm free space above the appliance. 2

5 Do not place anything on top of the appliance and do not sit on the appliance. Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the appliance. Make sure all filters are properly installed before you switch on the appliance. Avoid knocking against the appliance (the air inlet and outlet in particular) with hard objects. Always lift or move the appliance by the handle at the back of the appliance. Do not insert your fingers or objects into the air outlet. Do not use this appliance when you have used indoor smoke-type insect repellents or in places with oily residues, burning incense or chemical fumes. Do not use the appliance near gas appliances, heating device or fireplaces. Always unplug the appliance after use and before you clean it. Do not use this appliance in a room with major temperature changes as this may cause condensation inside the appliance. To prevent interference, place the appliance at least 2m away from electrical appliances that use airborne radio waves such as TVs, radios and radio-controlled clocks. The appliance is only intended for household use under normal operating conditions. Do not use the appliance in wet surroundings or in surroundings with high ambient temperatures, such as the bathroom, toilet or kitchen. The appliance does not remove carbonmonoxide (CO) or radon (Rn). It cannot be used as a safety device in case of accidents with combustion processes and hazardous chemicals. 3

6 Introduction Congratulations on your purchase and welcome to MEC! With this new Clean Air System you breathe cleaner air. For the best results, place the Clean Air System in a room where you spend most of your time, e.g. the living room or bedroom. Wherever there are people, plants or pets, there are airborne particles that can affect your well-being, especially if you suffer from allergies. Because of these particles, the air inside a room may be more polluted than the air in a large city. Normally, particles are invisible and odorless. Nevertheless they can affect your health. The - Clean Air System reduces the amount of animal dander and industrial pollutants in the air, and therefore improves the air quality. It also filters out ultrafine particles larger than 20 nanometers, including bacteria and some viruses. According to publications of the World Health Organization, the avian and human influenza viruses and the legionella bacterium are larger than 20 nanometers Filtration in several stages The air cleaner has a unique multi-stage filtration system that guarantees the best air quality: Stage 1: The pre-filter has been treated with antibacterial substances. It catches big particles like human hair, pet hair etc. Stage 2: The multi-filter which adopts organic antibacterial material filters out small particles and pollen. Also with antibacterial and antifungal functions, it can eliminate bacteria and fungi. Stage 3: The high-performance composite HEPA filter with anti-bacterial coating effectively removes fine dust and cigarette smoke, while the antibacterial and anti-mould functions of organic antibacterial materials eliminate germs and mould. - According to the publications of the World Heath Organization, the avian and human influenza viruses and legionella bacterium are larger than 20 nanometers. Stage 4: Activated carbon filter can effectively absorb formaldehyde, toluene, volatile organic compounds (VOCs),Ammonia, Acetaldehyde and Acid and other odors and harmful gases.. 4

7 Stage 5: Plasma generator makes use of the ionized plasma to form the plasma field, where can produces streamer discharge and partial ionization. During the gas ionization, it will produce large amount of oxygen, OH, active factor and radicals. Harmful substances in the gas will be decomposed and oxidized during the ionization discharge and streamer procedure. The bonds the disinfection and sterilization fundamentally and efficiently sterilize, degusting filter out smoke and odors Model and Filter Functions Model Filter Function P-F M-F-F H-P-H-F A-C-F P-Y-T-D-F P NANO HIPPO 50WH Yes Yes Yes Yes No Yes (P-F) : Pre-filter (H-P-H-F) : High Performance HEPA Filter (P) : Plasma (M-F-F) : Multi-fuction Filter (A-C-F): Activated Carbon Filter 5

8 Introduction 6

9 Picture 1 (For NANO HIPPO 50WH) Picture 2 (For NANO HIPPO 50WH) 7

10 General description 1. Control panel 2. Air quality sensor outlet 3. Air quality sensorpanel 4. Air quality sensor inlet 5. Remote control receiver 6. Air quality display 7. Four-side air inlet 8. Controller 9. Handle 10. Plasma generator 11. Air outlet 12. Cord storage facility 13. Mains cord 14. Panel on/off power on/off set 15. Activated carbon filter 16. High performance HEPA filter 17. Multi-functional filter 18. Pre-filter 19. Panel 8

11 General description Placing the filters The appliance comes with all filters fitted inside, but you have to remove the packaging of the filters before you can use the appliance. Remove all filters, unpack them and place them back into the appliance. Note: Make sure you insert the filters in correct position. Place your fingers on the top of the panel and gently pull the top part of the front panel towards you. Then lift the hooks at the bottom of the panel out of the bottom of the appliance. Remove the pre-filter by putting your fingers in the two flanges and pull the filter towards you. Remove all packing material from the filters. 4 Put filter 4 (activated carbon filter) back into the appliance or put filter 4 (nanometer photocatalysis titanium dioxide filter) back into the appliance. Note: Make sure that the side with the tag is pointing towards you. 5 Put filter 3 (HEPA filter) back into the appliance. Note: Make sure that the side with the tag is pointing towards you. 6 Put filter 2 (multifunctional filter) back into the appliance. Note:Make sure that the side with the tag is pointing towards you. 7 Put filter 1 (pre-filter) back into the appliance. Note: Make sure that the one side with the two projections ( FRONT tag and handle) are pointed towards you. Note: Make sure that all hooks are properly attached to the appliance. 8 To reattach the front panel, insert the bottom hooks into the bottom of the appliance first, then push the panel against the body of the appliance. 9

12 Plastic Hook Picture 3 Picture 4 Plastic Hook Picture 5 activated carbon filter Plastic Hook catalysis ilter Picture 6 Picture 8 Picture 7 T FRON Plastic Hook T FRON Picture 9 Picture Picture 11

13 POWER HIGH-SPEED MID-SPEED LOW-SPEED AUTO AIR-QUALITY RESET Take out / put into the power plug Press the arrowhead direction to open the power plug department. Picture 12 2 Open the power plug compartment to get the power cord from it. 3 Loose the band to use it. Picture 13 4Keep the power cord in the compartment while long time disuse. Take out / put into the power plug 1 Take out the remote control by arrowhead direction. Picture 14 2 Remove remote control s packing and battery protection. 3 Insert the battery protection and put the remote control into compartment while disusing. 11

14 Controlpanel operation method A B C D E F G H A---ON / OFF Put the plug in the wall socket, then you hear a beep, the appliance is in ready mode, the power indicator lights red, press POWER to start the appliance, then the power indicator lights blue. When the appliance is on, press the POWER, the appliance is back to the ready mode again. B---HIGH-SPEED When the appliance is on, press this button to select high-speed, the HIGH-SPEED light goes on. C---MID-SPEED When the appliance is on, press this button to select mid-speed, the MID-SPEED light goes on. D---LOW-SPEED When the appliance is on, press this button to select low-speed, the LOW-SPEED light goes on. E---SILENT MODE When the appliance is on, press this button to select silent mode, the SILENT light goes on F---AIR QUALITY When the appliance is on, press this button to make the air quality indicator on or off. Picture15 G---PLASMA When the appliance is on, press this button to make the plasma on or off. H---LIGHT SENSOR When the appliance is on, select AUTO mode, the appliance will sense the strength of the radial, so that the machine will select the night mode or day mode automatically. 12

15 Remote control operation methods I---POWER POWER Same as A in control panel I K---HIGH-SPEED Same as B in control panel J J---MID-SPEED Same as C in control panel K POWER Q Q---LOW-SPEED Same as D in control panel L---SILENT MODE Same as E in control panel L M P O P---AIR QUALITY Same as F in control panel M---PLASMA Same as G in control panel N---AUTO MODE Press this button to enter AUTO mode, the high, mid, low fan speed indicator will flash (about 1 second) in turn, you can see the details in operating mode N Picture16 REMOTE CONTROL O---RESET When the air quality indicator flashes (you need to replace the filter in two situations: the service life of the filter is over or filtering is not effective), press the RESET for 2 seconds, the filter s service time is resetting. 13

16 Operating mode When the appliance is plugged in, you can hear a beep, the appliance is operating normally. Memory store when power off, when the power is back, it will continue to work. 1.Normal operating mode When the appliance is on, it will enter into the normal operating mode by default. Press fan speed (H, M, L SILENT) to quit the auto mode, the appliance is entering into the normal operating mode. You can find the operating status as follows: A Mid-speed default, you can press the fan speed button to adjust the fan speed, the related lights will go on. B The PLASMA is on by default, press PLASMA button to press this button to make the plasma on or off. C The air quality indicator is on by default, press AIR QUALITY button to press this button to make the air quality indicator on or off. 2.AUTO MODE: Enter the auto mode by the AUTO button in the remote control, the high, mid, low fan speed indicator will flash (about 1second ) in turn, then the appliance is entering into the auto mode successfully. When entering into the auto mode, the machine will select the night mode or day mode automatically: the day mode by default, when the light is beginning to fade for 3 minutes, the appliance is entering into night model, instead, when the light is beginning to brighten for 5 minutes, the appliance will back to the day mode again. In day mode, you can find the operating status as follows: A. Plasms is on by default, press "PLASMA" button to turn the plasma on or off. B. The air quality indicator is on by default, press "AIR QUALITY" button to turn the air quality indicator on or off. 14

17 C According to the air quality, the motor will adjust the fan speed automatically: when the air quality is bad, the appliance is high speed; fair, mid speed; good, low speed. In night mode, you can find the operating status as follows: A B The PLASMA is on by default, press PLASMA button to make the plasma on or off. The air quality indicator is off by default, press AIR QUALITY button to make the air quality indicator on or off. C According to the air quality, the motor will adjust the fan speed automatically: when the air quality is bad, the appliance is mid speed; fair, the low speed; good, the appliance will enter to silent mode automatically. Adjusting the air quality sensor sensitivity People with certain health problems (e.g. allergies or asthma) have a greater need for healthy air. For this reason, the air cleaner allows you to adjust the sensitivity of the air quality sensor. When it is set to a higher sensitivity level, the appliance already starts cleaning the air at lower pollution levels to make the air even cleaner. There are four sensitivity levels: Common Standard Sensitive Extra sensitive The pollution sensor is set to standard sensitivity. You can adjust the sensitivity of the air quality sensor in the following way: 1 If the appliance is already plugged in, unplug the appliance and wait for a few minutes. 2 Under the standby press AIR- QUALITY+HIGH-SPEED buttons. After the buzzer sounds twice, the air quality sensor sensitivity has been set to extra sensitive level. Confirm it after five times flashing of the corresponding composite key indicator or confirm it immediately after pressing the power button to turn on the product. 15

18 Under the standby, press AIR-QUALITY+MID-SPEED buttons. After the buzzer sounds twice, the air quality sensor sensitivity has been set to sensitive level. Confirm it after five times flashing of the corresponding composite key indicator or confirm it immediately after pressing the power button to turn on the product. Under the standby, press AIR-QUALITY+LOW-SPEED buttons. After the buzzer sounds twice, the air quality sensor sensitivity has been set to standard level. Confirm it after five times flashing of the corresponding composite key indicator or confirm it immediately after pressing the power button to turn on the product. Under the standby, press AIR-QUALITY+SILENCE buttons. After the buzzer sounds twice, the air quality sensor sensitivity has been set to common level. Confirm it after five times flashing of the corresponding composite key indicator or confirm it immediately after pressing the power button to turn on the product. Note: When you change the sensitivity level, the appliance automatically starts operating at the set sensitivity level whenever you switch on the appliance. Sensitivity setting inquiry Under the standby, press the air quality indicator button to check the sensor sensitivity setting. Exit after the corresponding sensitivity indicate light flashes five times or exit by pressing other buttons except for reset button. Air quality indication Color Air quality Blue Very good Green Fair Red Bad Attention: In order to display the air quality in a precise way, we have divided the air quality(or purity degree) into 32 grades and each will be displayed by corresponding colors. When the air quality is between bad and fair(or fair and good), it will display the corresponding grade air quality color. With the changing of air quality, the air quality indicator will be changing accordingly. When the air quality changes suddenly, the air quality indicator will display the change of present color to the target color. Each color display time is about one second. 16

19 Maintenance Maintenance regularly clean the inside and outside of the body to prevent the dust from collecting on the inside and outside. 1 Wipe away dust with a soft dry cloth from the body of the appliance. 2 Clean the air inlet and the air outlet with a soft dry cloth. Never immerse the appliance in water or any other liquid. Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any part of the appliance. Only the pre-filter is washable. All other filters are NOT washable. Cleaning Pre-filter Clean the air quality sensor every 3 months for optimal functioning of the appliance. Clean it more frequently if you use the appliance in a dusty environment. Always unplug the appliance before you clean it. 1 Remove the pre-filter according to the second method of initial use. 2 Wash the pre-filter under a running tap. If the pre-filter is very dirty, use a soft brush to brush away the dust. You can also remove the dust by a vacuum cleaner. 3 Air-dry the pre-filter. Note: make sure the pre-filter is completely dry. 4 Put the pre-filter back into the appliance. Note: Make sure all the hooks have been correctly attached to the appliance. Note: Before cleaning, make sure to unplug the appliance. Picture 17 17

20 Air quality sensor Clean the air quality sensor every 2 months for optimal functioning of the appliance. Clean it more frequently if you use the appliance in a dusty environment. Note: When the humidity level in the room is every high, it is possible that condensation develops on the air quality sensor. As a result, the AIR QUALITY light on the control panel may indicate that the air quality is bad even though the air quality is good. In this case, you have to clean the air quality sensor. 1 Clean the air quality sensor inlet and the air quality sensor outlet with a soft brush. (shown as picture 18) 2 Remove the air quality sensor cover. ( shown as picture 19) 3 Clean the air quality sensor, the dust inlet and the dust outlet with a lightly moistened cotton swab. (shown as picture 20) 4 Dry them with a dry cotton swab. (shown as picture 20) 5 Reattach the air quality sensor cover. AIR OURLET FILM AIR INLET Picture 18 Picture 19 Picture 20 18

21 Filter replacement This air cleaner is equipped with the Smart Lock feature to ensure that the filters are in optimal condition when the appliance is operating. When one of the filters is almost full and has to be cleaned or replaced, the appropriate filter replacement light starts to flash. When you do not replace filter 2, filter 3 and filter 4, the appliance stops operating and the appliance is locked First alert to change the filter The filter function will be relatively weak when the lifetime is over. The air quality light will flash to remind the users changing the filter. Second alert to change the filter If you do not replace the filter in time after the first alert, approx. 3 weeks after the air quality light will flash and the buzzer sounds every 30 minutes to remind you replacing the filter. Filter replacement lock If you do not replace the filter in time during the first and second alerts, the appliance will be locked after operating approx 3 weeks: appliance stop working, power light and air quality light flash with continuous beep. 1 How long it takes before the appliance is locked depends on the operating time selected and the indoor air quality after the filter replacement alert. 2 When the appliance is locked, you hear a beep when you press any button. You can s witch off the appliance by pressing and holding the on/off button. 3 If the appliance is locked: Switch off the appliance and unplug it. Replace the appropriate filter (see section replacing the filters ) Replacing the filters and reset the appliance Replacing the filters Please refer to the ( Replacing the filters and reset the appliance section ) 19

22 Reset the appliance 1 After the filter replacement, put the plug into power socket and there will be the on music. The appliance reaches standby status. 2 Press the button RESET on the controller for 2 seconds or the reset button at the air quality sensor inlet for 2 seconds to make the reset. When the buzzer sounds one time, the using time of the filter has been cleared and restarted. The light of the air quality is on indicating that the reset is successful. AIR INLET Picture 21 Note: The reset button at the air quality sensor inlet can clear the filter using time and restart time counting at any time. If no encounter with special circumstances, please do not press the reset button when the filterreplacement light is not flashing. Note: Only replace a filter when the corresponding filter replacement light flashes. If you replace the filter before the filter replacement light starts flashing, the lifetime counter will not be reset but will continue counting the lifetime of the previous filters. As a result, the filter replacement light will start flashing much too soon. 20

23 TROUBLE SHOOTING This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Center in your country. Problem The appliance doesn t work No air comes out the air outlet Possible solution You ignored the filter replacement alerts. You did not replace the filter when the filter replacement light started flashing and did not respond when the appliance started to beep every 30 minutes after approx. 3 weeks. As a result, the appliance is now locked and you have to replace the filter and reset the appliance (see chapter Filter replacement ) so that the appliance can operate again. The appliance is not switched on. Put the plug into the wall socket and switch on the appliance. The fan speed does not change when the AUTO mode is activated When the room becomes dark, the night mode is activated automatically when the appliance is in the auto mode. In this case, the fan speed is set to a very low level. If you wan to change the fan speed, press the HIGH-SOEED, MID-SPEED and LOW-SPEED buttons to set the desired fan speed. 21

24 Problem The airflow that comes out of the air outlet is significantly weaker than before The air quality does not improve, even though the appliance has been operating for a long time. Possible solution 1. The pre-filter is dirty. Clean the pre-filter (see chapter maintenance and cleaning). 2. You haven t removed all packing material from the filters. Make sure that you have removed all packing material. 1. One of the filters has not been placed in the appliance. Make sure that all filters are properly installed in the following order, starting with the innermost filter: 1) activated carbon filter or nanometer photocatalysis titanium dioxide filter, 2) HEPA filter, 3) multi-care filter, 4) pre-filter. 2. The air quality sensor is wet. The humidity level in your room is high and cause con densation. Make sure the air quality sensor is dry and clean. (see chapter maintenance and cleaning ) 3 The room in which you run the appliance is larger than 55, which is the maximum size at which this air cleaner can operate effectively. The color of the air quality light always stays the same 1. The air quality sensor is dirty, clean the air quality sensor. (see chapter maintenance and cleaning ) 2. There is not enough ventilation in the room. Open a window to improve the air circulation. 22

25 Problem I need cleaner air because I have an allergy. The appliance is extra loud Possible solution You can change the air quality sensor sensitivity (see chapter using the appliance ) to make the air cleaner clean the air even better. You haven t removed all packing material from the filters. Make sure that you have removed all packing material. The appliance still indicates that I need to replace a filter, but I already did. Perhaps you did not press the filter reset button properly. Plug the appliance and press the reset button on the controller for 2 seconds or the reset button at the air inlet of the air quality sensor for 2 seconds. When the buzzer sounds one time, the using time of the filter has been cleared and restarted. The light of the air quality is on indicating that the reset is successful. 23

26

27 8-2, Wisma Fiamma, No. 20, Jalan 7A/62A Website