9.5KG WASHING MACHINE

Transcription

1 G9TLWW17 9.5KG WASHING MACHINE G9TLWW17_IB_Final170920V2.indd 1

2 G9TLWW17_IB_Final170920V2.indd 2

3 Contents Guide to the Appliance 2 Caring for the Environment 3 Safety Information and Warnings 4 Items in the Box 6 Getting Started 7 Basic Set Up 9 Operation Instructions 11 Troubleshooting 16 Care and Maintenance 18 Technical Specifications 20 1 G9TLWW17_IB_Final170920V2.indd 1

4 Guide to the Appliance Water Inlet (red) for hot water (at the upper back) Water Inlet (blue) for cold water (at the upper back) Detergent Drawer (inside) Top Lid Control Panel Drain Hose and Power Plug (at the lower back) Control Panel Remain Time(mins) ON/OFF Heavy Delicates Baby Clothes Water Level NOTE: Due to production improvements, the appliance may differ slightly from the diagram shown. Diagrams in this instruction manual are for reference only. 2 G9TLWW17_IB_Final170920V2.indd 2

5 Caring for the Environment Responsible disposal of the packaging The packaging of your appliance has been selected from environmentally friendly materials and can usually be recycled. Please ensure these are disposed of correctly. Plastic wrapping can be a suffocation hazard for babies and young children, please ensure all packaging materials are out of reach and are safely disposed of. Please ensure they are offered for recycling rather than throwing these materials away. Responsible disposal of the appliance At the end of its working life, do not throw this appliance out with your household rubbish. An environmentally friendly method of disposal will ensure that valuable raw materials can be recovered and used again. Electrical and electronic appliances contain materials and substances which, if handled or disposed of incorrectly, could be potentially hazardous on the environment and human health. Observe any local regulations regarding the disposal of electrical consumer goods and dispose of it appropriately. Contact your local authorities for advice on recycling facilities in your area. The plug must be rendered useless and the cable cut off directly behind the appliance or the machine to prevent misuse. 3 G9TLWW17_IB_Final170920V2.indd 3

6 Safety Information and Warnings For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety precautions listed below. WARNING! If you will not be using the washing machine for a while such as when you go on holiday, disconnect the plug from the mains supply and turn off the water supply to the washing machine. This is particularly important if there is no drainage around the washing machine. If the water supply is left on, water pressure may build up and cause a leak. General Use Transit bolts are used to transport the washing machine. You should remove these using a spanner or similar tool before you install the washing machine. If you do not, it will cause strong vibrations when the washing machine is spinning. Do not install your washing machine anywhere that is damp or exposed to the weather. If you do, it may cause an electric shock, fire, failure or deterioration. Do not pour water directly onto any part of the washing machine. It may cause a short circuit or electric shock. Keep flammable substances well away from the washing machine for example kerosene, gasoline, benzene, paint thinner and alcohol, or clothing soaked with these. They may cause an explosion or a fire. This washing machine is only suitable for washing textiles labelled washing machine washable. Before you start using the washing machine, turn the tap on to check that the hose is properly connected. If it s not, there may be a water leak. Do not put too much laundry or detergent into the washing machine. It may cause issues with the washing machine or laundry. Be careful not to get your laundry caught in the lid when you close it. This appliance is intended to be used in household and similar applications such as: - staff kitchen areas in shops, offices and other working environments; - farm houses; - by clients in hotels, motels and other residential type environments; - bed and breakfast type environments. This appliance is not intended to be used in areas for communal use in blocks of flats or in launderettes. Power Source and Cable Use an independent household dedicated mains socket, rated at 10 Amp 220V to 240V AC. If the washing machine is plugged in with other appliances, it may overheat and cause a fire. Make sure the mains plug is pushed firmly into the socket. A loose connection may overheat and cause electrical shock or a fire. Check the mains lead and mains plug for any damage. If the mains cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Unplug the mains lead when cleaning the washing machine. Do not touch the mains lead or mains plug with wet hands. It may cause an electric shock. Check the mains plug regularly for dirt. If dirt accumulates on the mains plug, it could cause a fire. To prevent this, unplug the cable and clean the mains plug with a dry rag. 4 G9TLWW17_IB_Final170920V2.indd 4

7 Safety Information and Warnings If you disconnect the mains plug, hold onto the mains plug not the cable. Pulling the cable may cause an electric shock or a fire. Do not use a mains plug adapter or extension cable. It may overheat and cause a fire. Make sure your home voltage matches the voltage displayed on the washing machine. If you are not sure, contact an electrician. The mains plug must remain accessible to allow disconnection or an all pole switch must be incorporated in the fixed wiring in accordance with the wiring regulations. To Prevent Injury / Damage Do not climb on the washing machine. You may hurt yourself or damage the washing machine. When opening and closing the lid ensure you keep fingers away from the door hinge, or this could lead to injury. Check your washing for objects such as nails, pins, coins, clips etc. They could damage your laundry or the washing machine. To prevent any large, heavy objects (e.g., buckles, large buttons, etc.) from hitting the drum or lid, turn your clothing inside out or remove the heavy objects. They could damage your laundry or the washing machine. Do not wash, rinse or spin water-proof sheets or clothing. These may cause vibration or washing machine failure during spin-drying, which could lead to injury, damage to the washing machine or damage due to water leaking. Be careful when draining hot water or any detergent from the drum. Do not dismantle, repair or modify the washing machine. The washing machine could malfunction and cause a fire or injury. This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Keep the appliance and its cord out of reach of children. Children should be supervised to ensure that they do not play with the appliance. The appliance is to be connected to the water mains using the new hose-set supplied. Old hose-sets should not be reused. The ventilation openings in the base of the washing machine must not be obstructed by a carpet. WARNING IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE PERSONNEL TO CARRY OUT SERVICING OR REPAIRS WHICH INVOLVE THE REMOVAL OF COVERS. TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS YOURSELF. 5 G9TLWW17_IB_Final170920V2.indd 5

8 Items in the Box Remove all items from the packaging. Retain the packaging. If you dispose of it please do so according to local regulations. The following items are included: Main unit Water Supply Hose x 2 Drain Hose Support Instruction Manual Instruction Manual 6 G9TLWW17_IB_Final170920V2.indd 6

9 Getting Started Please Read And Follow The Instructions Carefully. In addition to the instructions mentioned here, special regulations of the relevant water and power supply companies may apply. If in doubt, have the washing machine connected by a qualified technician. The washing machine is heavy - caution when lifting it. Do not lift by projecting components. Warning: Frozen hoses may tear/burst. Do not install the washing machine in outdoor areas or where there is a risk of frost. Lay hoses and cables in such a way that there is no risk of tripping over them. NOTE: An additional space (approximately 120mm) is required at the rear of the washing machine. This is to allow enough space for the water hose and drain hose connections. Choosing the right location for your washing machine Make sure there s enough space for your washing machine. Install your washing machine on a flat, stable surface to avoid excessive vibrations and noise. Don t install your washing machine in direct sunlight or in a place where temperatures can reach freezing. The ventilation openings in the base of the washing machine must not be obstructed by carpet. Start by tilting the washing machine backwards. One person should stand behind it, holding the rear of the top panel. The other person should grip the bottom feet at the front. Check that you have all the required accessories for installation. We recommend that you entrust the installation of the washing machine to a qualified technician. 7 G9TLWW17_IB_Final170920V2.indd 7

10 Getting Started Moving the washing machine from one location to another Before you move the washing machine: Shut off the tap and run the washing machine to drain the water. Drain any remaining water from the pump hose. Disconnect the mains cable. Two or more people are required to move the washing machine. Levelling the washing machine There are levelling feet on the underside of the washing machine. They must be adjusted to make sure the washing machine is level. 1. On each front foot, loosen the lock ring by turning it clockwise. 2. Adjust all feet by rotating each upwards or downwards. 3. Use a spirit level to ensure the washing machine is level. 4. Tighten each lock ring by turning them anti-clockwise (towards the washing machine body). Ensure all lock rings are tightened securely. Check that the feet are still bolted to the washing machine - if they re unbolted, the washing machine will move around. 8 G9TLWW17_IB_Final170920V2.indd 8

11 Basic Set Up Connecting the water supply hose 1. To prevent leakage from the connection joints, ensure the rubber washer seals are fitted to each end of the water supply hose. Do not use without the seals in place. 2. Fit the straight end of the blue-indicated water supply hose to the cold water tap and the red-indicated water supply hose to the hot water tap. IMPORTANT: Take care to fit the hot and cold hoses to the correct tap. The cold water hose is not suitable for hot water. 3. Connect the angled end of the blue-indicated hose to the cold water inlet valve and the red-indicated hose to the hot water inlet valve on the machine. Hand tighten the plastic parts of the connections. If you are unsure, please call a qualified plumber for safer connections. IMPORTANT: If the water supply in your household exceeds 0.6 MPa, fit pressurereducing valves to the household water inlet taps. 4. Open the tap slowly and check that there are no leaks around the connection joints. Points to remember Follow the instructions in this section to avoid water leaks. Don t connect the hose to a combination tap. Don t twist, squash, modify or cut the hose. This machine is designed to connect to both cold and hot water supply. Use only the new water supply hose sets supplied. Old hose sets should not be reused. Connecting the water drain hose Points to remember: Before connecting to the waste pipe, make sure to check the waste pipe and remove any stopper or blockage inside, otherwise the unit may not be able to expel the waste water properly. 1. Completely sleeve the drain hose over the waste pipe. 2. Fix and tighten. Don t twist, pull out or bend the drain hose. Do not place it under the washing machine. 3/4 3/4 9 G9TLWW17_IB_Final170920V2.indd 9

12 Basic Set Up Your washing machine should be no more than 3 meters from the drain outlet. The water drain hose should be mounted at a minimum height of 86cm and a maximum height of 100cm from the floor. IMPORTANT: The water will overflow when the height of the drain hose is under 86 cm cm Connecting to the power supply For your safety: Make sure the power supply system (current, power voltage and wire) at your home can meet the normal loading requirements of the unit. Connect the power to a socket which is correctly installed and properly earthed. Make sure the power voltage at your place is same to that in the machine s rating label. Do not use a power plug adapter or extension cable. Do not connect and pull out the plug with wet hands. When connecting and pulling out the plug, hold the plug tightly and then pull it out. Do not pull power cord forcibly. If the power cable or power plug is damaged, stop using them and call a qualified technician for assistance. The power plug must remain accessible to allow disconnection or an all pole switch must be incorporated in the fixed wiring in accordance with the wiring rules. 10 G9TLWW17_IB_Final170920V2.indd 10

13 Operation Instructions Organising laundry Read the washing label on each garment to help you sort your washing into different loads. Sort the laundry by colour, type of fabric and by how soiled it is. This will help you choose the correct program and temperature for each wash. Do not exceed the maximum load! Preparing laundry Treat stains before washing. Program Some items should be put into a cleaning net before going into the washing machine, i.e. bras with metal wires, tights and lace clothing to prevent damage. Check that pockets do not contain any objects which may damage your clothes and the washing machine. Tie up any loose strings on laundry, close zippers and reverse clothing with zips inside out. Large heavy objects (e.g., buckles, large buttons, etc.) could damage your laundry or the washing machine. Turn your clothing inside out, or remove the heavy objects. Remove any surplus hair, animal fur, sand and other materials with a brush before washing. If clothes have raised fabric, turn them inside out. Heavy 9.5 Jeans 9.5 Delicates 9.5 Standard 9.5 Quick 4 Baby Clothes 6 Clothes that are not colour fast should be washed separately. Maximum Loading Capacity (kg) Put your clothes into the washing machine. Close the washing machine lid. Ensure that no items of clothing are trapped after closing the washing machine lid. Don t overload the drum as it may cause excessive vibrations or damage the washing machine. 11 G9TLWW17_IB_Final170920V2.indd 11

14 Operation Instructions Adding detergent Open the washing machine lid, pull out the detergent drawer and add detergent into it. You can also directly add detergent onto the laundry. Apply detergent according to the washing amount, the soiling level, the water hardness in your area and the manufacturer s instructions of these products. For slightly dirty clothes, put a small amount of detergent. For excessively dirty clothes, put a larger amount of detergent. To prevent powder detergent from staying in the detergent drawer, dry the inside of the drawer with a cloth. Make sure the powder isn t lumpy when you add it into the drawer. If the rinse cycle isn t removing all the detergent from your wash, use less detergent. Liquid detergent should not exceed the maximum level in the drawer. You can use liquid detergents in all programs. Dilute viscous liquid detergent with water. Prevent blockage of the overflow. For woolen items, use a mild liquid detergent. Other detergents may damage your woolen clothes. With wool or silk, you may need to use an extra rinse cycle to remove excess detergent from your clothes. This depends on the amount of detergent you use and the amount of foam that develops in the main wash cycle. 12 G9TLWW17_IB_Final170920V2.indd 12

15 Operation Instructions Before first use Before washing your clothes for the first time, run a full wash program first (without laundry): 1. Connect the machine to the mains power supply and the water supply. 2. Put a small amount of detergent in the detergent drawer. Close the drawer and the washing machine lid. 3. Press the ON/OFF button. 4. Select the Heavy program. 5. Turn on the water supply. 6. Press the START/PAUSE button. NOTE: Water is poured into the washing machine to perform an inspection at the time of shipment from the factory, so there may be drops of water or condensation in the washing machine. This is not an indication of a malfunction. Standard washing 1. Pull up the lid and put the laundry in the drum. 2. Add detergent into the detergent drawer. The quantity of detergent will depend on the amount of laundry and the degree of soiling. Use the amount of detergent suggested on the packaging. 3. Close the detergent drawer and lid. Make sure no washing gets caught in the lid. 4. Connect the machine to the mains power supply. Press the ON/OFF button. 5. Select your wash program. The selected program indicator will either light up or flash. You can also press WASH, RINSE and SPIN buttons to select a single wash procedure or a combination of procedures. 6. Select the temperature according to the dirtiness of the laundry by pressing the TEMP button repeatedly. Hot water for dirtier laundry. NOTE: To use hot water, make sure the red-indicated water supply hose is connected to the hot water tap and hot water inlet valve. 7. Select the water level according to the quantity of laundry. Select 6 for larger washing loads. 8. Turn on the water supply. 9. Press the START/PAUSE button to start the washing. 10. The washing machine will sound when the washing is complete. Turn off the water supply and unplug from the mains power supply. 13 G9TLWW17_IB_Final170920V2.indd 13

16 Operation Instructions NOTE: During initial start-up and use of the unit, there may be a slight smell while the motor is settling in. This is not a fault; this is normal operation. Ensure the lid is closed, the washing machine will automatically stop if the lid is open. For 2 options sharing 1 indicator, the indicator will either light up or flash when the option is selected as indicated on the unit s control panel (e.g. for Water level, the indicator for 1, 3, 5 will light up, but will flash for 2, 4, 6). Selecting the program (maximum amount of dry clothing/cloth to be washed is 9.5kg) Program Description Water level Wash time (min) Rinse cycles Spin time (min) Program time (1) (min) Heavy Jeans Delicates Suitable for larger loads. Suitable for heavilysoiled clothing. Suitable for more delicate clothing Standard (2) Standard fabric washing program Quick Baby Clothes Suitable for lightlysoiled and summer clothing. Multiple rinse cycles, to reduce the detergent residue on the clothes Energy test program: Standard (under the highest speed; others as the default) Half load for 9.5kg machine: 4.75kg. NOTE: (1) For reference only; the actual program time may vary, depending on the different parameters such as the water pressure and the drain speed. (2) Standard is the standard washing program to which the information in the label relates, and it is suitable to clean normally soiled cotton laundry and that it is the most efficient program in terms of combined energy and water consumptions for washing that type of cotton laundry, that the actual water temperature may differ from the declared cycle temperature. 14 G9TLWW17_IB_Final170920V2.indd 14

17 Operation Instructions Setting delay time washing Delay time means the preset starting time of washing. 1. After putting in the laundry and detergent, close the lid, plug in the mains power and press the ON/OFF button. 2. Turn on the water tap. 3. Select the wash program, water level and temperature. 4. Press the DELAY button repeatedly until the desired delay time is reached, then press the START/PAUSE button. Washing will start once the desired delay time is reached. NOTE: The maximum delay hours is 24 hours. Each press of the DELAY button adds 1 hour to the delay time. Cancelling or changing the delay time washing To cancel the delay time, press the ON/OFF button. To change the delay time, cancel the delay time first, then press the DELAY button to re-set another delay time. Enabling and disabling the Child Lock function To enable the Child Lock function, press the SPIN and WATER LEVEL buttons at the same time for 3 seconds to lock the buttons on the control panel. To disable the Child Lock function, press the SPIN and WATER LEVEL buttons at the same time again for 3 seconds to unlock the buttons on the control panel. 15 G9TLWW17_IB_Final170920V2.indd 15

18 Troubleshooting Issues No inflow of water Washing cycle will not begin Water leakage Water has overflowed from the bottom of the machine Indicator or display does not light Detergent residues in the drawer Washing is still dirty Abnormal noise Great vibration Solutions Check if the power is off or the fuse is burned out. Check if the water supply is cut off or if the water pressure is too low. Check if the inlet hose is properly connected and the water tap is on. Check if the filtering screen of the inlet valve is blocked by dirt or damaged. Check if the START/PAUSE button has been pressed. Check if the power is off or if the fuse has burned out. Check if the power supply voltage is too low. Check if the water level reaches the required water level (the unit will not work if the water level does not reach the required water level). Check if the Delay function has been set. Check and fasten water pipes. Clean up outlet hose or contact GVA customer care. Fix the inlet pipe. Replace the drain hose. Check if the power is turned on and the power plug is connected correctly. Contact GVA customer care. Clean and wipe the drawer. Use liquid detergents or change detergent. Use less detergent. Dilute liquid detergent. Select a suitable cycle. Add the proper detergent quantity according to the instructions on the detergent package. Check if the transport bolts have been removed. Check if it is installed on solid and level floor. Check if there are any metal articles inside. Check if the legs of the unit are level. 16 G9TLWW17_IB_Final170920V2.indd 16

19 Troubleshooting Issues Abnormal draining Abnormal spinning Solutions Check if the water drain hose is placed too high. Check if the internal drain valve is blocked by dirt. Check if the lid is closed. Check if the clothing is piled unevenly on one side or if excessive clothing has been loaded in the machine. Check if the unit is placed on a flat stable surface and not on an inclined surface. The motor belt may be loose, contact GVA customer care. Error codes Display LED E1 E2 E3 E4 Description Alarm for water inlet Alarm for water drain Alarm for opened lid Alarm for imbalance of the unit Solution Open the water tap, to check if the supply hose is squashed or kinked. Check if the filter in the inlet valve is blocked. Check if the water pressure is too low. Check if the drain pump is blocked. Wash the drain pump filter. Wash the drain hose. Check if the lid of the washing machine is closed. Check if the clothes are pinned by the lid. Check if the clothing is piled unevenly on one side or if excessive clothing has been loaded in the machine. Check if the unit is placed on a flat stable surface and not on an inclined surface. Others Contact GVA customer care if there are still other problems. 17 G9TLWW17_IB_Final170920V2.indd 17

20 Care and Maintenance IMPORTANT: Always unplug the washing machine before cleaning. Cleaning the drum Any rust left inside the drum by metal articles must be removed immediately with chlorine-free detergent. Never use steel wool. NOTE: To prevent build-up of detergent residue, it is recommended to wash the appliance without any load or detergent once a month. Cleaning the exterior of your washing machine Clean the outside of your washing machine with a soft cloth and mild detergent such as kitchen detergent. Don t splash water over the washing machine. Do not use cream cleansers, thinners or products containing alcohol or kerosene. Cleaning the water inlet hose filter After long time use, the water inlet hose filter may be blocked with smudginess, and should be cleaned. 1. Switch on the power, turn on the water tap then turn off. 2. Let the unit work for 5 seconds so that water flows through the water inlet hose, then switch off the power. 3. Disconnect the water inlet hose (be careful of spilling water) and clean the water inlet hose filter, then restore the water inlet hose. Cleaning the lint filter After long time use, the lint filter inside the drum needs to be washed. 1. Take out the lint filter. 2. Open the filter and wash it with water. 3. Close the filter and replace back in place. 18 G9TLWW17_IB_Final170920V2.indd 18

21 Care and Maintenance Cleaning the lid Wipe the inner lid after each wash to remove lint and stains. Remove any coins, buttons and other objects from the drum after each wash. Cleaning the drain filter IMPORTANT: Before cleaning the drain filter, switch off and unplug the washing machine. Be careful not to burn yourself while cleaning the drain filter. Water draining from the filter compartment may be hot after a high temperature wash. 1. Loosen the drain pump cover by turning it anti-clockwise then remove. Drain the water out of the pump, under which place a container to catch the water. 2. Take out the filter. Remove any lint and debris before carefully putting it back in place. 3. Close the drain pump cover and turn it clockwise to lock back into place. Preventing a frozen water supply hose If your washing machine is delivered in freezing weather conditions, leave it at room temperature for 24 hours after you ve set it up before using it. This ensures there s no ice blocking the water supply hose. If your water supply hose freezes, add 2 or 3 litres of warm water to the drum and wait for 10 minutes. 19 G9TLWW17_IB_Final170920V2.indd 19

22 Technical Specifications Model Rated Voltage Rated Power Standard Water Pressure Washing Capacity Dimensions (H) x (W) x (D) Weight G9TLWW17 240V~ 50Hz 600W 0.1MPa - 0.6MPa 9.5kg 1015 mm x 601 mm x 625 mm Approx. 45kg Features and specifications are subject to change without prior notice. IMPORTANT: If the water supply in your household exceeds 0.6 MPa, fit pressurereducing valves to the household water inlet taps. 20 G9TLWW17_IB_Final170920V2.indd 20

23 G9TLWW17_IB_Final170920V2.indd 21

24 M.E.W. (Australia) Pty Ltd. 15 Vaughan Street Essendon Fields, Vic 3041 ACN After sales support: Aus customercare@gvaproducts.com.au gvaproducts.com.au While every effort has been made in the preparation of this Instruction Manual, the publishers can not be held responsible for the accuracy of the information contained herein or any consequences arising from it. IB-G9TLWW V2 G9TLWW17_IB_Final170920V2.indd 22