Important Safeguards (For your safety, please follow the instructions below.) Specification. High Speed Hand Dryer. Warning

Transcription

1 INSTALLATION MANUAL Important Safeguards (For your safety, please follow the instructions below.) In this Instruction Manual, the following symbols are shown for safe and proper use of your automatic faucet and in order to alert you to the possibility of personal injury and damage to your property. The symbols and their meanings are as follows. arning Ignoring these symbols may cause personal injury and/or property damage. *Some models may have different components from the ones illustrated below. Do not Caution Do not disassemble Do not use in humid area Ignoring these symbols may cause severe injury and/or property damage. arning Do not install the unit in the places where corrosive or combustible gas can be present. This may cause product failure or damage. Never attempt to disassemble for repair or modification. This may cause electric shock, fire, injury or failure Do not install outdoors or where it is exposed to water. This may cause current leakage, electric shock, fire, or failure. Important Important Do not! Product Power Rating Power Connection Power Saving Function Decibel Rating Air Speed Dry Time Capacity Ambient temperature Specification HDR100#GY Clean Dry High Speed Hand Dryer 120V AC, 4.25 Amps, 60 Hz, 510 Hardwiring Automatically turns OFF after 60 seconds of use 62 db 224 mph (100 meters/second) 12 seconds 0.20 gal (700 ml) F (0-40 C) Size 9-5/8" x 18-1/2" x 6-5/16" eight 10 lbs (4.5kg) arning It is recommended to install a circuit-breaker in the power supply Failure to do this may cause electric shock during overload or short circuit. Caution The chassis assembly must be installed on a smooth and even wall surface which has enough strength. Failure to do this may cause damage or personal injury if it falls down. Notice Do not place anything beneath the unit; leave a clearance of 3-15/16 (100mm). Do not install on uneven wall surface. If air flow is not good, the product may not perform well. 0GU

2 * Before Installing 1. Precautions Confirm the rough-in, major dimensions and wiring diagram before installation in order to properly install the hand dryer and electrical wiring. All electrical wiring should be installed in accordance with national/local codes and regulations with an assistance from a certified electrician. Clearance for drain tray, shown in Set-up Drawing, is required for proper air flow into the unit and maintenance of the tray. Set-up Drawing Some models may have different components as illustrated below. 3 HOLE BRACKET DIA. 5/32 (4mm) 7-13/16 (199mm) 3-1/16 (77mm) DIA. MOUNTING HOLES (4) 5/32 (4mm) 6-11/16 (170mm) 6-5/16 (162mm) 9-5/8 Mounting surface should be even and smooth. Confirmation must be made that the wall has enough strength for hand dryer installation and be sure to use all the mounting harware provided to securely install the hand dryer. 9-7/16 (240mm) ELECTRICAL INLET 7/8 (22mm) DIA. HOLE (470mm) (470mm) It is necessary to install circuit breaker for the power supply. 2. Others Pay special attention so that both top cover and sensor surface are not flawed or scratched. Do not place other devices using inverter or infrared sensor near the hand dryer, this may cause malfunction. *Recommended mounting bracket heights from floor are as follow: -Male/Female: 53 (1346 mm) -Children: 47 (1194 mm) -Handicapped: 45 (1143 mm) Meets the American Disabilities Act Guidelines, ANSI A117.1 and CSA B651 requirements when mounted in a recessed wall where the front surface is not more than 4 (102mm) from finished wall and max. height of air blower outlet from finished floor is 47-1/4 (1200mm). (actual placement) (470mm) 10-3/8 (263mm) CLEARANCE FOR DRAIN TRAY AND AIR FLO PATH** 7-1/8 (180mm) 8-7/8 (224mm) 9-5/8 9.5/8 TOP COVER ASSY UNIT* DRAIN TRAY ASSY* DRAIN TRAY 6-5/16 (160mm) 6-5/16 (162mm) 7 (177mm) 4-5/16 (110mm) FINISHED ALL 5/8 (16mm) 7-13/16 (199mm) 9-7/16 (240mm) 3-15/16 (100mm) *Top Cover Assy Unit and Assy are two separate parts. **Clearance is required in order to take off the tray for cleaning and maintenance and have good air flow into the unit. Ø4.5X30 (mm) SCRE POER CABEL (HARDIRING) Ø4.5X30 (mm) SCRE Ø4.5X30 (mm) SCRE 5/8 (16mm) FLOOR

3 Installation *Some models may have different component as illustrated below. Hand Dryer Unit w/o Top Cover Sensor Platform for Mounting bracket Chassis Assy. <Bottom view> air nozzles Power switch (Connection type) ON POER OFF Filter all surface back of Drain Tray Assy. Assy Drain tray Filter case Filter case <View with cover removed> Accessories Model is subject to change without further notification. Mounting Bracket Screws and vandal resist Hex rench Template Owner s and Installation manual Installation position (φ4.5 30)X7

4 Installation Procedure STEP 1 1 Use template, mark the wall for locations and install the mounting bracket. Mounting Bracket STEP 1 Caution Mark the wall with template and install the bracket Chassis Assy. must be installed on a rigid and even surface Failure to do this may cause damage or personal injury when it falls. Chassis Assy. 2 Complete the electrical wiring; install the junction box,and connect the power cord using wire nuts. 3 Mount the Chassis and 4 Install the top cover and drain tray junction box location Attach the bracket firmly on the rigid wall with three screws (φ4.5 30) provided. In the case of a tile or concrete wall, please use plastic plug anchors with screws provided. Screw (x3) (φ4.5 30) 3 HOLE BRACKET DIA. 5/32 (4mm) Screw (x4) (φ4.5 30) 7-13/16 (199mm) 9-7/16 (240mm) (actual placement) 3-1/16 (77mm) DIA. MOUNTING HOLES (4) 5/32 (4mm) ELECTRICAL INLET 7/8 (22mm) DIA. HOLE 7-1/8 (180mm) 8-7/8 (224mm) 9-5/8 6-11/16 (170mm) (470mm) 35-3/4 (907mm) Floor surface 45-3/16 (1147mm) *Recommended mounting bracket heights from floor are as follow: -Male/Female: 53 (1346 mm) -Children: 47 (1194 mm) -Handicapped: 45 (1143 mm) 46-3/4 (1186mm) 53 (1346mm) * To be continued on the back

5 STEP 2 - STEP 4 STEP 2 Complete the electrical wiring STEP 3 Mount the Chassis and Use the special hex wrench provided to remove the 2 screws (φ4 10) from the top cover, then remove the cover. Put the connection point (with wire nuts) into the junction box. To remove the top cover, pull the lower part 1 towards you and pull Hang the Chassis onto the mounting bracket. the upper part 2 upward, then remove it. Insert the Assy. into the bottom of the Chassis, and attach Hang Chassis Assy. mounting platform onto mounting bracket hooks.. the lower part of the Assy. 1 to the Chassis Assy. 2 with 2 Connect the power cord inside the main body case with the power cord screws (Ф4.5 30) provided. out of the wall and use wire nuts (certified electrician to confirm the specific wire nut to use). Vandal resist Screw for (x2) mounting bracket Chassis Chassis mounting platform Chassis mounting bracket hooks mounting bracket (Actual Placement) STEP 4 Install the top cover and drain tray 1 Insert the hook of the top cover into the slot at the upper part of the Chassis, 2 then put the cover down. Then, fasten the cover with two screws (Ф4 10) that were previously taken out. * POER MUST BE IN OFF POSITION DURING INSTALLATION. Connection diagram hook of Slot at the upper part of the Chassis Assy. Chassis Connection point (Actual Placement) Screw for (x2) (φ4 10) Drain tray Connect the cord firmly with a wire nut or equivalent. hen installing the drain tray, slide it completely into its maximum depth. Drain Basin

6 Function Test 1. Checking after installation iring Diagram Test the product as follow after the installation is complete. First peel off the seal on the filter. (The seal is used to protect the filter from scratches during shipment; it is no longer needed.) Sensor Control Power Switch P6 P5 Bu P4 R P7 P2 Air nozzles Peel off the seal P1-1 Motor P1-2 P3 B 1. Check the main Power Supply Switch. Turn on the main power supply switch on. Power Connector B Power Fuse Power Switch B Motor Check the power switch of the hand dryer Turn the power swtich ON. Check the functionality Place your hand under the outlet nozzles to see if air blows out. G B=BLACK R=RED =HITE Bu=BLUE G=GREEN After trial run After you check the functionality by trial run, give the User Manual (with arranty) to the customer, and explain how to use and maintain the product.