AUTOMATIC SCRUBBER. Read these instructions before using the machine MODELS: SCC172 QSCC172 SCHC

Transcription

1 AUTOMATIC SCRUBBER MODELS: SCC172 QSCC172 SCHC HCC172 QSCC172IA QSC IPX4 Read these instructions before using the machine V /20/10 PRV NO

2 MACHINE DATA LOG/OVERVIEW MODEL DATE OF PURCHASE SERIAL NUMBER SALES REPRESENTATIVE # YOUR DEALER Name: Address: Phone Number: OVERVIEW The Automatic Scrubber is a battery powered, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with a brush or pad, and then vacuums the soiled water back into the recovery tank SCRUBBER 01/03/07

3 TABLE OF CONTENTS Machine Data Log/Overview...2 Table of Contents...3 HOW TO USE THIS MANUAL How to use this Manual SAFETY Important Safety Instructions Hazard Intensity Level Safety Label Location OPERATIONS Technical Specifications How the Machine Works Components Controls Machine Operation Pre-Run Machine Inspection Filling Solution Tank Scrubbing Emptying & Cleaning Tanks MAINTENANCE Batteries Battery Maintenance Checking Battery Specific Gravity Charging the Batteries On-Board Charger Battery Selection Changing Batteries Battery Connections Scrub Brushes Types Replacing or Removing Scrub Brushes Installing Scrub Brushes Squeegee Blades Replace Squeegee Blade Remove Squeegee Assembly Service Schedule Machine Troubleshooting PARTS LIST Decal Control Panel-w/Charger Control Panel-SCHC172 w/charger Control Panel-QSC Hour Meter Handle Recovery Tank Scrub Brush/Pad Driver Scrub Motor/Lift Solution Tank Squeegee Squeegee Lift Vacuum Wheel & Frame Onboard Charger Wiring Battery Cables Wiring Main Harness all except QSC172 & SCHC Wiring Main Harness SCHC Wiring Main Harness QSC Wiring Schematic all except QSC172 & SCHC Wiring Schematic SCHC Wiring Schematic QSC Suggested Spare Parts SCRUBBER 10/12/09 3

4 HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. NOTE: For warranty information, contact your local dealer or sales representative. MODEL DATE OF PURCHASE SERIAL NUMBER SALES REPRESENTATIVE # DEALER NAME OPERATIONS GUIDE NUMBER PUBLISHED The model and serial number of your machine are located as shown. The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards are identified that could result in product or personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order: - Batteries - Scrub Brushes - Squeegee - Service Schedule - Machine Troubleshooting The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information: - REF column refers to the reference number on the parts illustration. - PART NO. column lists the part number for the part. - PRV NO. reference number. - QTY column lists the quantity of the part used in that area of the machine. - DESCRIPTION column is a brief description of the part. - SERIAL NO. FROM column indicates the first machine the part number is applicable to. When the machine design has changed, this column will indicate serial number of applicable machine. The main illustration shows the most current design of the machine. The boxed illustrations show older designs. - NOTES column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts SCRUBBER 08/20/09

5 IMPORTANT SAFETY INSTRUCTIONS When using a battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer s recommended components and attachments. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow. This machine is not suitable for picking up hazardous dust. Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors. This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. Disconnect battery before cleaning or servicing. Before the machine is discarded, the batteries must be removed and properly disposed of. Make sure all warning and caution labels are legible and properly attached to the machine. During operation, attention shall be paid to other persons, especially children. Before use all covers and doors shall be put in the positions specified in the instructions. When leaving unattended, secure against unintentional movement. The machine shall only be operated by instructed and authorized persons. Only chemicals recommended by the manufacturer shall be used. This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other brushes may affect its safety. Do not use on surfaces having a gradient exceeding 2%. SAVE THESE INSTRUCTIONS SCRUBBER 01/03/07 2-1

6 HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage. FOR SAFETY: To Identify actions which must be followed for safe operation of equipment. Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel. FOR SAFETY: DO NOT OPERATE MACHINE: Unless Trained and Authorized. Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep solution tank in raised position when charging. Keep sparks and flames away from the batteries. Do not smoke around batteries. Disconnect batteries before working on machine. Only qualified personnel should work inside machine. Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact with the acid contained in the batteries. Never allow metal to lie across battery tops SCRUBBER 01/03/07

7 SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. FLAMMABLE MATERIALS CAN CAUSE EXPLOSION OR FIRE. DO NOT USE OR PICK UP FLAMMABLE MATERIAL. SAFETY LABEL PRV NO BATTERY CAUTION PRV NO SCRUBBER 08/20/09 2-3

8 TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Rated Voltage 24 VDC Rated Amperage 30 Amps Batteries 2 x 12 Volt AH Scrub Brush Motor 0.75hp (0.56 kw) Vacuum Motor 24 VDC 2 stage by pass Mass (GVW) 319 lbs (144.7 kg) Weight empty without batteries 142 lbs (64.4 kg) Solution Control Gravity feed, fully variable Solution tank capacity 8 Gal (30.3 l) Recovery tank capacity 10 Gal (37.9 l) Scrub brush diameter 17 in (430 mm) Scrub brush pressure 33 lbs (15 kg) Scrub brush speed 200 RPM Wheels 2 x 6 in (15 cm) Thermoplastic non marking Casters 3.0 x 1.0 (75 mm) Foundation Pressure 286 lbs/in² ( Kpa) Coverage 6700 ft²/hr Frame Construction Steel with epoxy powdercoat finish Minimum aisle u-turn width 44 in (1110 mm) Maximum rated climb and descent angle with empty 2% tanks Maximum rated climb and descent angle with full tanks 2% SCRUBBER 01/03/07

9 ITEM MEASURE Height 35 in (0.89 m) Length 42 in (1.07 m) Width without squeegee 20 in (0.51 m) Width of squeegee 31 in (0.79 m) Width of scrub path 17 in (0.43 m) TECHNICAL SPECIFICATIONS Length Width Height SPECIAL NOTES: The A-weighted sound pressure level emitted by the appliance was measured to be 74.1 dba. This is a space-averaged, broad-band measurement determined according to IEC 704-I. This appliance contains no possible source of impact noise. The overall root-mean-squared acceleration at the operator s arms was measured to be less than 1.0 m/s². This is a tri-axial, broadband measurement made during normal operation on a composite tile floor SCRUBBER 08/20/09 3-2

10 HOW THIS MACHINE WORKS This Automatic Scrubber is a battery powered, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with a brush, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system and recovery system. The function of the solution system is to store cleaning solution and deliver it to the scrub system. The solution system consists of the solution tank, strainer, and valve. The solution tank stores cleaning solution (water and detergent) until it is delivered to the scrub system. The strainer protects the valve from debris. The machine has a ball-type valve which controls the amount of cleaning solution delivered to the scrub system. The solenoid type valve controls the delivery of cleaning solution to the scrub system. The valve automatically prevents solution flow unless the scrub brushes are turned on. The solution control lever controls the amount of cleaning solution delivered to the scrub system. The function of the scrub system is to scrub the floor. The scrub system consists of a rotary type disk scrub brush, motor, and lift linkage. The brush scrubs the floor and the motor drives the brush. The brush lift lever raises and lowers motor and brush. The function of the recovery system is to vacuum the soiled water back into the recovery tank. The recovery system consists of the squeegee, vacuum motor, screen, and recovery tank. The squeegee wipes the dirty solution off the floor as the machine moves forward. The vacuum motor provides suction to draw the dirty solution off the floor and into the recovery tank. The screen protects the vacuum fan from debris. The recovery tank stores the dirty solution. The float ball in the tank activates when the recovery tank is full SCRUBBER 01/03/07

11 COMPONENTS Control Panel 2. Control Handle 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Recovery Tank Domel 6. Scrub Brush/Pad 7. Solution Tank 8. Solution Tank Cover 9. Solution Tank Drain Hose 10. Solution Strainer 11. Solution Tank Support Lanyard 12. Squeegee 13. Vacuum Motor 14. Solenoid Valve SCRUBBER 08/20/09 3-4

12 CONTROLS Solution Control Lever 2. Brush Switch 3. Brush Lift Pedal 4. Vacuum Switch 5. Squeegee Lift Lever 6. Battery Charge Level Indicator 7. Hour Meter 8. Circuit Breaker 9. Brush Reverse Switch SCRUBBER 08/20/09

13 CONTROLS 1. SOLUTION CONTROL LEVER Controls solution flow to scrub deck. To increase flow push the knob forward to the desired flow. To decrease flow pull the knob back. 2. BRUSH SWITCH Controls the scrub brush motor. To turn scrub brush on, press the top of the switch. To turn scrub brush off, press the bottom of the switch. 3. BRUSH LIFT PEDAL Raises and lowers the brush. To lower the brush, push down on pedal and move to the left. To raise the brush, lift the lever from its lowered position. 4. VACUUM SWITCH Controls the vacuum motor. To start vacuum motor, press the top of the switch. To stop vacuum motor, press the bottom of the switch. 5. SQUEEGEE LIFT LEVER Raises and lowers the squeegee. To lower the squeegee, lift and pull the lever to the right and then lower. To raise the squeegee, lift the lever and push it to the left. 6. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bars illuminated on the top indicate full charge. Bars flashing near the bottom indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries. When the machine is left overnight with less than a full charge, the display may initially indicate a full charge. It will also indicate a full charge if the batteries are disconnected, then reconnected. After a few minutes of operation the meter will give the correct charge level. 7. HOUR METER Records the number of hours the machine s brush has been in operation. This information is useful in determining when to service the machine. 8. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip, the cause of the electrical overload should be found and corrected. 25 Amp. Protects the scrub brush motor. 25 Amp. Protects the vacuum motor. 9. BRUSH REVERSE SWITCH Reverses the scrub brush motor. To activate, press the top of the switch SCRUBBER 01/03/07 3-6

14 MACHINE OPERATIONS PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. NOTE: See maintenance section for pre-run machine inspection checklist items. FILLING SOLUTION TANK FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine. NORMAL SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising and lowering scrub brush/squeegee. NOTE: In order to achieve the best possible results, the area that is to be cleaned should be swept before scrubbing. Large debris, strings & wire must be removed to prevent being caught in the brush or squeegee. 1. Turn the machine off. 2. Remove solution tank cover. 3. Fill the solution tank with clean water, leaving enough room for the required amount of cleaning solution. The solution tank capacity is 8 gallons (30.3 liters). The water must not be hotter than 140 F (60 C) to prevent damage to the tank. 4. Measure the chemical into the solution tank. Liquid chemicals should be added to the solution tank after filling with water. Dry chemicals should be thoroughly mixed before being added into the solution tank. Commercially available, high alkaline floor cleaners are suitable for use in the solution system. NOTE: Read the chemical manufacturers recommended proportion instructions. 5. Replace solution tank cover. Flammable materials can cause an explosion or fire. Do not use flammable materials in the tanks SCRUBBER 01/03/07

15 TO BEGIN SCRUBBING When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. Flammable liquids and/or reactive metals can cause explosions or fire! Do not pick up. 1. Lower the squeegee. 2. Turn the vacuum on. 3. Lower the scrub brush to the floor. 4. Turn the scrub brush on. 5. Push machine forward to begin scrubbing. NOTE: Shut machine off immediately if water or foam is expelled from the machine. 6. Adjust the solution flow as necessary. TO STOP SCRUBBING 1. Turn the scrub brush off. 2. Raise the scrub brush. 3. Raise the squeegee. 4. Turn the vacuum off. DOUBLE SCRUB For floors, which are heavily soiled or have thick accumulations of floor finish the machine may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, make the first pass over the surface being cleaned with the squeegee up, vacuum off, the solution on, and brush down and on. This allows the solution to stay in contact with the soil while loosening the surface accumulation with the brush. Allow time for the first application to stay in contact with the floor. MACHINE OPERATION The length of time between the first and second pass depends on the amount of accumulation and the type of chemical being used. A second scrubbing with the squeegee down, vacuum on and again with solution and brush on will further loosen the soil. The additional application of solution will further assist the difficult cleaning job. FOR SAFETY: When using machine, go slow on inclines and slippery services. EMPTYING AND CLEANING TANKS 1. Park the machine next to a drain. Drain hoses are on the rear of the machine. 2. Turn the machine off. SOLUTION TANK 1. Pull the small drain hose from the retainer. Lower the hose in the direction of the drain. 2. Remove the solution tank cover. 3. Flush the solution tank out with clean water and run several gallons of clean water through systems. Do not use water hotter than 140 F (60 C) to clean the tank, damage may occur. NOTE: Never allow solution to remain in tank. Damage to tank, seals and valves could occur. 4. Replace drain hose to retainer. RECOVERY TANK 1. Unhook the large drain hose from the retainer. Unscrew the drain cap from the end of the recovery tank drain hose. Lower the hose in the direction of the drain. Do not stand in front of the end of the hose. Recovered solution will come out with force. 2. Flush the recovery tank out with clean water. Do not use water hotter than 140 F (60 C) to clean the tank, damage may occur. 3. Clean off the float and check for free movement of the float ball. 4. Replace the drain plug and secure the drain hose in the retainer SCRUBBER 08/20/09 3-8

16 MAINTENANCE BATTERIES (WET CELL BATTERIES ONLY) The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life from the batteries, charge them when their charge level reaches 25% of a full charge. Use a hydrometer to check the charge level. Do not allow the batteries to remain in a discharged condition for any length of time. Never expose a discharged battery to temperatures below freezing. Discharged batteries will freeze causing cracked cases. Do not operate the machine if the batteries are in poor condition or if they have a charge level below 25% (specific gravity below 1.155). Keep all metallic objects off the top of the batteries, as they may cause a short circuit. Replace worn or damaged cables and terminals. Check the electrolyte level in each battery cell before and after charging the batteries. Never add acid to the batteries, use distilled water. Do not allow water level to fall below the battery plates. Portions of plates exposed to air will be destroyed. Do not overfill. Keep plugs firmly in place at all times. When servicing machine, avoid contact with battery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. Charge batteries in a well ventilated area. BATTERY MAINTENANCE 1. When cleaning the batteries, use a solution of baking soda and water. Do not allow the cleaning fluid to enter the battery cells, electrolyte will be neutralized. 2. Maintain the proper electrolyte level in each battery cell. If a cell should accidentally overflow, clean immediately. 3. Wipe off the top of the batteries at least once a week. 4. Test battery condition with a hydrometer at least once a week. 5. Ensure that all connections are tight and all corrosion removed. 6. Every 4 to 6 months remove the batteries from the machine and clean the battery cases and battery compartment SCRUBBER 01/03/07

17 MAINTENANCE CHECKING BATTERY SPECIFIC GRAVITY Use a hydrometer to check the battery specific gravity. TO CHARGE THE BATTERIES When servicing machine, avoid contact with battery acid. Battery Check Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the reading may not be accurate. Check the hydrometer readings against this chart. SPECIFIC GRAVITY BATTERY 80 F (27 C) % CHARGED % CHARGED % CHARGED % CHARGED DISCHARGED NOTE: If the readings are taken when the battery electrolyte is any temperature other than 80 F (27 C), the reading must be temperature corrected. To find the corrected specific gravity reading when the temperature of the battery electrolyte is other than 80 F (27 ): Add (+) to the specific gravity reading (4 points), for each 10 F (6 C) above 80 (27 C). Subtract (-) from the specific reading (4 points), for each 10 F (6 C) below 80 F (27 C) Charge batteries in a well ventilated area. Leave the solution tank open. MACHINES EQUIPPED WITH ONBOARD CHARGER 1. Fully open Recovery Tank/Battery Cover or prop in partially open position using bracket (included). This will provide additional venting of batteries during charging cycle. 2. Connect charger s AC power cord to AC mains. The charger s YELLOW AC LED will light. NOTE: When charger is energized, all machine function will shut down. 3. After several seconds, the charger s green LED will flash to indicate that charging is in process. NOTE: If no lights are illuminated, or yellow LED flashes, refer to the charger Product Manual Troubleshooting section. 4. When charging is complete, both the yellow and green LEDs will remain on. The charger is now in standby mode. 5. Disconnect charger s AC power cord. 6. Raise battery cover and check the battery electrolyte level. It should be up to the indicator ring. If necessary, add distilled water. 7. Lower the battery cover NOTE: For additional information about battery charger function, please see the charger Product Manual SCRUBBER 01/03/07 4-2

18 MAINTENANCE-From Serial Number ** ON-BOARD CHARGER BATTERY SELECTION! WARNING Disconnect charger from wall outlet before changing charge profiles. Failing to do so could result in electrical shock. Only dipswitch SW1 effects the charging curve. Select the appropriate dip switch setting from the Charging Curve Table. Do not change settings of SW2. Changing settings of SW2 dipswitch could result in charger failure. DIPSWITCH: SW1 Charging Curve Table DP1 DP2 CHARGING CURVE ON OFF IUIa-ACD-for Wet batteries (default setting) ON ON IUIa-O AGM-for AGM or Gel batteries (maintenance free) Dipswitches are located behind the label on the front of the charger. Peel the top right corner back to reveal two sets of dipswitches. Once the appropriate charger setting has been selected, replace label. To verify charger settings, observe charger immediately after startup. When configured for lead-acid batteries, the red LED will flash twice. If configured for gel/agm batteries the green LED will flash twice. **CALL MANUFACTURER FOR SERIAL NUMBER SCRUBBER 11/25/09

19 MAINTENANCE MACHINES WITHOUT ONBOARD CHARGER Use a 24 volt, 12 amp maximum output, DC charger which will automatically shut off when the batteries are fully charged to charge the two battery pack. 1. Stop the machine in a clean, well ventilated area next to the charger. 2. Turn the machine off. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine. 3. Drain recovery tank and raise the recovery tank. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. 4. Check the electrolyte level in each battery cell. Before charging, add just enough distilled water to cover the plates. After charging is complete, add just enough distilled water to bring up the level to the indicator ring. If the water level is too high before charging, normal expansion rate of the electrolyte may cause an overflow. Resulting in a loss of battery acid balance and damage the machine. 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machine. CHANGING BATTERIES Stop the machine in a clean area next to the charger. Turn off machine. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine. 1. Drain recovery tank and raise the recovery tank. 2. Disconnect battery pack from machine. 3. Disconnect squeegee lift cable and vacuum hose. 4. Prepare a suitable site to place the batteries. 5. Pull battery tray with batteries out of rear of machine. Batteries are a potential environmental hazard. Consult your battery supplier for safe disposal methods. + red - blk - blk + red FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 7. Plug the charger connector into the battery connector. Connect the charger AC plug to a wall outlet. The charger gauge should indicate that the batteries are charging. 8. When the batteries are fully charged, disconnect the charger from the AC wall outlet, then disconnect the charger from the batteries. 9. Connect the batteries to the machine connector. 10. Check the electrolyte level. It should be up to the indicator ring. If necessary, add distilled water. 11. Lower the recovery tank SCRUBBER 01/03/07 4-4

20 MAINTENANCE SCRUB BRUSHES NOTE: All original equipment brushes are equipped with Perform Alert. This feature will tell the operator when it is time to replace the scrub brush. Perform Alert brushes have pre-trimmed bright yellow tufts to indicate the length of a worn out brush. When the tufts in the scrub brush wear to a length equal to the yellow tufts, the scrub brush should be replaced. There are three different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market and further add to the flexibility of the Saber Compact. Please refer to the following to assist in selecting the proper brush or pad for the work at hand. UNCOATED FLOORS Mild Grit is a less aggressive silicone carbide grit suitable for cleaning medium soil conditions. Advantages are faster ground speed than nylon bristles on light solid applications. Polypropylene is a general-purpose scrub brush with stiff bristles. Polypropylene works well for maintaining concrete, wood and tile floors. FINISHED FLOORS Nylon bristles are used in a variety of applications on coated or uncoated surfaces. White Pads (Polishing) are used for dry polishing to achieve a high-gloss appearance, or surface washing on highly polished or burnished floors. Red Pads (Buffing) are used for light-duty scrubbing. When used with a mild detergent they will provide surface cleaning without removing the finish. Blue Pads (Scrubbing) are used for heavy-duty scrubbing and light stripping. The blue pads remove less finish than brown stripping pads, yet will remove black marks, stains and dirt. Brown Pads (Stripping) are used for easy and complete removal of old floor waxes/finishes. They will quickly remove ground in dirt, black heel marks, and spills. When used with the proper stripper, this pad leaves the floor clean and ready for finishing. The scrub brush should be checked before each days work for wire, string, wear and damage. The scrub brush should be replaced if brush bristles are missing or if yellow Perform Alert indicates minimum brush length SCRUBBER 01/03/07

21 MAINTENANCE REPLACING OR REMOVING SCRUB BRUSHES 1. Turn the machine off. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine. 2. Raise the scrub deck up by pushing down on the pedal. 3. Locate the brush reverse switch on the rear of the panel. Press to activate the motor then release to disconnect brush driver. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. Check both the front and rear squeegee blades for damage and wear each day in the pre-run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness. TO REMOVE SQUEEGEE ASSEMBLY 1. With the squeegee in the up position, turn the machine power off. 4. Tilt and pull machine back to expose brush driver. 2. Loosen both squeegee knobs and pull squeegee assembly rearward from the lifting carrier. 3. Inspect or repair as necessary and reinstall. INSTALLING SCRUB BRUSHES 1. Turn the machine off. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine. 2. Tilt and push machine over brush driver. The brush centering bracket will position the brush driver. TO REPLACE SQUEEGEE BLADES 1. With the squeegee in the up position, turn the machine power off. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine. 2. Remove the squeegee assembly from the machine. Remove all screws and remove blade retainer strap and remove squeegee blade. 3. Replace squeegee blades as required. 4. Install squeegee blade. 3. Lower the scrub deck by pushing the pedal down and to the left. 5. Install squeegee retainer strap. 6. Install all screws starting from center and working to ends. 4. Locate the brush switch and turn on SCRUBBER 01/03/07 4-6

22 MAINTENANCE SERVICE SCHEDULE Before starting the work period End of work period before storing MAINTENANCE DAILY WEEKLY MONTHLY ANNUALLY Check battery acid level * Check vac hose connections * Clean the squeegee blades * Inspect brush or pad for debris: * wire string, wear Inspect float ball screen * Drain & rinse tanks * Raise squeegee assembly * Raise scrub deck assembly * Charge the batteries. * Remove the pad driver/brush * Check the brush/pad for damage * and/or wear Clean squeegee blades * Clean recovery tank shut off & * screen Check battery cells w/ hydrometer * Check solution strainer * Check pivot points and casters for * proper lubrication Inspect tank and hoses * Clean tops of batteries * Check battery cable clamps * Use a vacuum to remove lint from * the motor windings Grease casters * Inspect all motors for carbon motor brush wear * SCRUBBER 01/03/07

23 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Poor or no water pick-up Debris caught on squeegee Remove debris Vacuum motor does not run, or runs slowly Poor scrubbing performance Brush motor does not run, or runs slowly Worn squeegee blades Vacuum hose clogged Vacuum hose disconnected from squeegee or recovery tank Vacuum hose damaged Vacuum motor inlet screen dirty Recovery tank not sealed Foam filling recovery tank Recovery tank full Circuit breaker tripped Loose connection Faulty vacuum contractor Worn vacuum motor brushes Debris caught in scrub brush Worn brush or pad Improper detergent, brush or pad used Low scrub brush down pressure Low battery charge Circuit breaker tripped Loose connection Faulty brush motor contactor Worn brush motor brushes Replace squeegee blades Clear obstruction from hose Reconnect vacuum hose Replace vacuum hose Clean inlet screen Check vacuum motor position. Replace damaged seal. Empty recovery tank Use less or different detergent Use defoamer Drain recovery tank Reset circuit breaker Check motor wires and connections Replace contactor Replace brushes, check commutator Remove debris Replace brush or pad Contact equipment or application specialist Increase brush pressure Charge batteries Reset circuit breaker Check motor wires and connection Replace contactor Replace brushes, check commutator SCRUBBER 01/03/07 4-8

24 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank No power to machine Little or no propel Solution flow turned off or set too low Solution strainer plugged Solution hoses obstructed Solution solenoid valve obstructed or stuck Battery disconnected Emergency shut-off activated Battery connections corroded Faulty main contactor Faulty power switch Low battery charge Machine turned on with directional control button(s) not in neutral Controller overheated Loose connection Turn on or increase flow setting Clean solution strainer Clear obstruction from hose Clean or replace Check all battery cable connections Reset Clean connections Replace contactor Replace switch Charge batteries Allow control button to return to neutral. Restart Allow cool down period Check motor wires and connection SCRUBBER 01/03/07 4-9

25 17 SCRUBBER PARTS LIST SCRUBBER 01/03/07

26 DECAL 1A 1B 3A 3B 2A 2B SCRUBBER 04/17/09

27 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A LABEL, MAIN (RIGHT) SCC172, QSCC172, SCHC172, QSC172 1B LABEL, MAIN (RIGHT) HCC172 2A LABEL, MAIN (LEFT) SCC172, QSCC172, SCHC172, QSC172 2B LABEL, MAIN (LEFT) HCC172 3A LABEL, LOGO DOMED SCC172, QSCC172, SCHC172, QSC172 3B LABEL, LOGO DOMED HCC LABEL, CIRCUIT BREAKER LABEL, PANEL 17 IN DECAL SCRUBBER 04/17/09 5-2

28 CONTROL PANEL- W/CHARGER SCRUBBER 01/03/07

29 CONTROL PANEL W/CHARGER REF PART NO. PRV NO. QTY DESCRIPTION SWITCH, DPDT 2-POSITION ROCKER SWITCH, SPST 2-POSITION ROCKER SWITCH, DPST 2-POSITION ROCKER SCR, X 1/2 PTHMS BLK NP HANGER, CHARGER CORD BOOT, M12 CIRCUIT BREAKER BRKT, HOSE HOOK BUSHING,.75 ID X.25 H STANDOFF, 1/4-20 X 1.0 HEX INS SET SCR, 1/4-20 X 1.25 L NUT, 1/4-20 UNC NUT, HEX NYLOCK BREAKER, 25A, 250VAC 50VDC NUT, 1/4-20 HEX NYLOCK SCR, X 3/8 PPHMS SS PANEL, SCRUBBER 17 IN WASHER, 1/4 LOCK EXT STAR SS STANDOFF, HEX BRASS 6-32 THRD METER, 24V BATTERY W/OUTPUT RELAY, 24VDC 40A /BRKT GASKET, ELECTRIC COVER SIDE GASKET, ELECTRICAL COVER SERIAL NO. FROM NOTES: SCRUBBER 01/03/07 5-4

30 CONTROL PANEL- SCHC172 W/CHARGER SCRUBBER 01/03/07

31 CONTROL PANEL SCHC172 W/CHARGER REF PART NO. PRV NO. QTY DESCRIPTION SWITCH, DPDT 2-POSITION ROCKER SWITCH, SPST 2-POSITION ROCKER SWITCH, DPST 2-POSITION ROCKER SCR, X 1/2 PPHMS BLK NP HANGER, CHARGER CORD BOOT, M12 CIRCUIT BREAKER BRKT, HOSE HOOK BUSHING,.75 ID X.25 H STANDOFF, 1/4-20 X 1.0 HEX INS SET SCR, 1/4-20 X 1.25 L NUT, 1/4-20 HEX UNC BLACK C NUT, HEX NYLOCK SS BREAKER, 25A, 250VAC, 50VDC SCR, X 3/8 PPHMS SS NUT, 1/4-20 HEX NYLOCK PANEL, SCRUBBER WASHER, 1/4 LOCK EXT STAR SS STANDOFF, HEX BRASS 6-32 THRD METER, 24V BATTERY W/OUTPUT RELAY, 24VDC 40A W/BRKT GASKET, ELECTRICAL COVER SIDE GASKET, ELECTRICAL COVER RELAY, BATTERY METER OUTPUT SERIAL NO. FROM NOTES: SCRUBBER 04/17/09 5-6

32 CONTROL PANEL QSC SCRUBBER 04/17/09

33 CONTROL PANEL-QSC172 REF PART NO. PRV NO. QTY DESCRIPTION SWITCH, DPDT 2-POSITION ROCKER SWITCH, SPST 2-POSITION ROCKER SWITCH, DPST 2-POSITION ROCKER SCR, X 1/2 PPHMS BLK NP GASKET, ELECTRICAL COVER BOOT, M12 CIRCUIT BREAKER BRKT, HOSE HOOK BUSHING,.75 ID X.25 H STANDOFF, 1/4-20 X 1.0 HEX INS SET SCR, 1/4-20 X 1.25 L NUT, 1/4-20 HEX UNC BLACK C NUT, HEX NYLOCK SS BREAKER, 25A, 250VAC, 50VDC SCR, X 3/8 PPHMS SS NUT, 1/4-20 HEX NYLOCK PANEL, SCRUBBER WASHER, 1/4 LOCK EXT STAR SS STANDOFF, HEX BRASS 6-32 THRD METER, 24V BATTERY W/OUTPUT GASKET, ELECTRICAL COVER SIDE SERIAL NO. FROM NOTES: SCRUBBER 04/17/09 5-8

34 HOUR METER SCRUBBER 04/17/09

35 HOUR METER REF PART NO. PRV NO. QTY DESCRIPTION WIRE, 3.5 BLK/ X WIRE ASM, HOUR METER METER, VDC LED HOUR DIODE ASM, X RESISTOR ASM, 2.7K OHM 1 WATT SERIAL NO. FROM NOTES: SCRUBBER 04/17/

36 HANDLE SCRUBBER 08/20/09

37 HANDLE REF PART NO. PRV NO. QTY DESCRIPTION HANDLE, 17 IN SCRUBBER SERIAL NO. FROM NOTES: KNOB, 2.25 OD X 5/16-18 X 2.19 STUD ALL EXCEPT SCHC LOCK, HANDLE, MALE LOCK, HANDLE, FEMALE BRKT, HANDLE MOUNT SUPPORT CAP, HANDLE SCR, 5/16-18 X 2.25 BSHCS SS SCHC172 ONLY SCRUBBER 04/17/

38 RECOVERY TANK A 5B SCHC SCRUBBER 07/27/09

39 RECOVERY TANK REF PART NO. PRV NO. QTY DESCRIPTION DOME, 13 X SCR, #10 X 3/4 PPHST TYPE B SS PLATE, VAC INLET COVER FLOAT SHUT-OFF 5A TANK, RECOVERY DK GRY SERIAL NO. FROM NOTES: ALL EXCEPT SCHC172 5B TANK, RECOVERY, TEAL SCHC CUFF, HOSE, 1.5 IN BLACK LANYARD, DRAIN HOSE QSC172 ONLY HOSE, 1.5 BLK VAC X HOSE, 1.5 BLK VAC X CLAMP, 1.75 WORM GEAR X DRAIN CAP ASSEMBLY HOSE, P-TRAP 45 DEG GASKET, DOME EDGE GASKET, VAC INLET CLIP, VAC HOSE COIL CORD, 1/8 X BAFFLE, AIR INTAKE SCR, X.748 PPHMS SS C NUT, HEX NYLOCK SS C WASHER, #10 X 9/16 OD SCRUBBER 07/27/

40 SCRUB BRUSH/PAD DRIVER SCRUBBER 04/17/09

41 SCRUB BRUSH/PAD DRIVER REF PART NO. PRV NO. QTY DESCRIPTION PAD DRIVER, 17 BA LOCK, PAD CENTER SNAP, TWO STEP SCR, 8-32 X 3/4 PTHMS SS 4A BRUSH, 17 POLYPRO BA 4B BRUSH, NYLON BA 4C BRUSH, 17 GRIT BA 4D BRUSH, NYLON UNTRIMMED SCR, M6 X 40MM PFHMS SS LUG, BRUSH MOUNTING SERIAL NO. FROM NOTES: SCRUBBER 04/01/

42 SCRUB MOTOR/LIFT 1 2A 3A 3B B 31 SCHC SCRUBBER 07/17/09

43 SCRUB MOTOR/LIFT REF PART NO. PRV NO. QTY DESCRIPTION MOTOR ASM, 24VDC 200 RPM GEAR SERIAL NO. FROM NOTES: 2A VALVE, 24VDC SOL 3/8 HOSE CIM ALL EXCEPT SCHC172 2B VALVE, 24VDC SOL 1/2 HOSEBARB SCHC172 3A HOSE 3/8 NYLOBRD X 3.5 ALL EXCEPT SCHC172 3B HOSE, 1/2 VINYL X 4 SCHC172 4 OPEN BRKT, SOLENOID VALVE BRKT, MTR MNT STIFFENER NUT, 5/16-18 HEX NYLOCK SS WASHER, THRUST.51 ID X 1 OD BRO WASHER, THRUST.51 ID X 1 OD X BUSHING,.5 OD X.31 ID X.4 L SS WASHER, 5-16 SS FLAT SCR, 5/16 18 X 1.25 HHCS SS BRKT, MOTOR TRACK WASHER, 3/8 X 7/8 OD SS SCR, 3/8-16 X 1 HHCS GR BRKT, DECK STIFFENER SCR, X 3/8 HHMS SS WASHER, M5, FLAT, ISO7089, SS SPRING, BRUSH CLIP DRIVER, BRUSH ASSIST WASHER,.344 ID X 1.13 OD X.09 T PLT WASHER, 5/16 SPLIT LOCK PLTD SCR, 5/16-18 X 1HHCS SS WASHER,.78 ID X 1.63 OD X.197 PLT SPRING, EXT.50 OD X 2.25 L X.063 W PIN, CLEVIS 3/16 X.50 PLTD LEVER, MOTOR LIFT SHOULDER BOLT, 3/8 OD X 1/2L SS BRKT, MOTOR TRACK BRKT, MOTOR MOUNT KEY, 1/4 SQ X SCR, M4 X 8MM LG PPHMS SCR, M5X12, SHCS, ISO4762, SS WASHER, #10 SPLIT LOCK PLTD SCRUBBER 07/17/

44 SOLUTION TANK A 32B A 20 19B A 18B SCRUBBER 08/20/09

45 SOLUTION TANK REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: HINGE, 17 IN SCRUBBER WASHER, 1/4 LOCK EXT STAR SS SCR, 1/4-20 X 1/2 PTHMS CABLE, TANK LANYARD SHOULDER BOLT, 5/16 X 3/8 SSHLD BRKT, TANK SUPPORT COVER, SOLUTION TANK CORD, 1/8 X HOSE, 1/2 ID WIRE BOUND X HOSEBARB, 3/8 MPT X 1/2 90 D BRKT, VALVE MOUNT SPACER,.259 ID X 3/8 OD X LEVER, SOLUTION CABLE NUT, HEX NYLOCK SS SCR, HHSS, M4X5.3 SS WAS SCR, X 1/2 HHCS SS WASHER, #10 X 9/16 OD 18A HOSE, 3/8 ID X.05 W CLR X 12 NYLOBRD ALL EXCEPT SCHC172 18B HOSE, 1/2 VINYL X 15 NYLOBRD SCHC172 19A HOSEBARB, 3/8 MPT X 3/8 NYLON ALL EXCEPT SCHC172 19B HOSEBARB, 3/8 MPT X 1/2 NYLON SCHC NUT, SEALED BULKHEAD VALVE, 3/8 FPT BALL CLAMP, 1.0 WORM GEAR HOSEBARB, 1/2 MPT X 3/4 90D HOSE, 3/4 ID X.12 W CL X 36 L NUT, HEX NYLOCK SCR, X 1/2 PPHMS BLK KNOB, SOLUTION LEVER HOSEBARB, 1/2 MPT X 3/ STRAINER, 3/8 NPT 20 MESH CLAMP, 5/16 NYLON LABEL, VENT/DRAIN 32A TANK, SOLN SC17 DK BLU ** 32B TANK, SOLN SC17 DK GRY ** SCR, X 3/8 PPHMS SS WASHER, #10 FLAT PLTD WASHER, #10 X 9/16 OD ** CALL MANUFACTURER FOR SERIAL NUMBER ALL EXCEPT HCC172 WAS HCC172 WAS SCRUBBER 08/07/

46 SQUEEGEE A 8B 8C 8D A 18B SCRUBBER 09/17/10

47 SQUEEGEE REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: SCR, 1/4-20 X.59 PPHMS SS C TUBE, 17 IN. TRANSITION GASKET, SUCTION, SQG TRANS KNOB, 1.5 OD X 5/ BRKT, SQUEEGEE MOUNT KNOB, SQUEEGEE RETAINER STRAP, SQUEEGEE BLADE, REAR 8A BLADE, SQUEEGEE, REAR 8B BLADE, RED REAR SOFT DURO 40 OPTIONAL 8C BLADE, BLU, RIB FRT/REAR URETHANE OPTIONAL 8D BLADE, RED, REAR MEDIUM DURO 60 OPTIONAL SHOULDER BLT,.305 OD X 1.77 SS C WASHER, 5/16 X.63 SS WHEEL, 3 DIA CUSHION RUBBER BUSHING, SPANNER.435 X PLATE, TOP, CAST SQG NUT, 5/16-18 JAM SS SQUEEGEE, END INSERT 17 IN SCR, 5/16-18 X 1.77 BHSMS SS SCR, 5/16-18 X 2.17 BHSMS SS 18A BLADE, SQUEEGEE FRONT 18B BLADE, RED FRONT 5 SLOT DURO 40 OPTIONAL STRAP, FRONT AND REAR STANDARD WHEEL, 1.5 OD X.31 ID X.75 W GRY WASHER, 5-16 X.55 SS COTTER, 5/16 RING WASHER, SEAL 5/16 X 3/4 OD SS BRKT, SQG WHEEL PIN, CLEVIS 5/ C NUT, 5/16-18 HEX NYLOCK SS GASKET, LOWER, 17" SQG SQUEEGEE, CENTER INSERT, 17IN SCR, 1/4-20 X 1.25 PPHMS SS SQUEEGEE, 17 INCH CAST * * COMPLETE ASSEMBLY, ITEM 5 NOT INCLUDED SCRUBBER 09/17/

48 SQUEEGEE LIFT SCRUBBER 04/17/09

49 SQUEEGEE LIFT REF PART NO. PRV NO. QTY DESCRIPTION NUT, 1/4-20 HEX NYLOCK NUT, 5/16-18 HEX NYLOCK SS PIN, CLEVIS 3/8 X 3.50 PLTD COTTER, 3/8 RING SCR, 5/16-18 X 1.25 HHCS SS BEARING, FLANGED.314 ID X.502 OD WASHER, THRUST.51 ID X 10 D BRO PLATE, SQUEEGEE LIFT WASHER, THRUST.51 ID X 1 OD X HOOK, SAFTEY CLIP CABLE, SQUEEGEE LIFT 21.4 L LEVER, SQUEEGEE LIFT NUT, HEX NYLOCK SHOULDER BOLT, 5/16 OD X 2.0 L SERIAL NO. FROM NOTES: SCRUBBER 04/17/

50 VACUUM SCRUBBER 04/17/09

51 VACUUM REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: GASKET, VAC MTR 2A VAC MOTOR, 24VDC 2ST TD 2B BRUSH SET, 24/36V VAC, WINDSOR SERVICE ONLY ELBOW, VAC MUFFLER 90 DEG BRKT, VAC MOTOR MNT BRKT, MUFFLER MUFFLER, VACUUM FOAM BLANKET, SOUND REDUCTION SCR, 1/4-20 X 5/8 HHCS SS NP WASHER, 1/4 ID X 5/8 OD SS SCRUBBER 04/17/

52 WHEEL & FRAME SCRUBBER 04/17/09

53 WHEEL & FRAME REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM FRAME, 17 IN SCRUBBER SCR, 5/16-18 X 1.89 HHCS SS C WHEEL, 3 DIA CUSHION RUBBER BUSHING, SPANNER.435 X PLATE, CASTER MOUNT NUT, 5/16-18 HEX NYLOCK SS BRKT, SPLASH GUARD NUT, HEX NYLOCK SS SWIVEL CASTER, 3.7 *(1) WASHER, 5/16 SPLIT LOCK PLTD SCREW 5/16-18 X 1.00 BSHCS SS *(1) SCR, X 5/8 HHMS SS WASHER, #10 X 9/16 OD SKIRT, CASTER SHIELD PLATE, BRUSH CENTER SCR, 1/4-20 X 1.2 HHCS SS WASHER, 1/4 ID X 1.0 OD FLAT SS WHEEL, 1.25 TREAD X 6 DIA SCR, 5/16-18 X 2.5 FHSC SS 20 OPEN OPEN STRAP, SKIRT SIDE SKIRT, 17 SCRUBBER SCR, X 1/2 PTHMS SS NOTES: *SEE SERIAL NUMBER PAGE SCRUBBER 06/22/