TOTAL FILTRATION MANAGEMENT

Transcription

1 TOTAL FILTRATION MANAGEMENT

2 Compressed Air 6 ISO Air-Cooled Aftercooler 8 Water-Cooled Aftercooler 9 Compressed Air Filter 10 Filter Housing With Flanges 11 High Pressure Filter Housing 12 Prefilter Elements 13 Microfilter Elements 14 Activated Carbon Elements 15 Alternative Elements 16 Activated Carbon Tower 18 Measuring Instruments 19 Oil / Water Separator 20 Activated Carbon Bags 21 Refrigeration Dryer 50Hz 22 Refrigeration Dryer 60Hz 23 High Pressure Refrigeration Dryer 24 AIR Membrane Dryer 25 Heatless Adsorption Dryer 26 Compact Adsorption Dryer 28 High Pressure Air Dryer 40 Bar 29 Heat Regenerated Dryer 30 Compressed Air Receiver 32 Breathing Air Filter System 34 Proces Air 36 Process Air Prefilter Element 37 Sterile Depth Filter Element 38 Process Filter Housing 39 Sterile Membrane Filter 40 Sanitary Air Filter Housing 41 Steam Filter 42 Filter Housing For Steam 43 Sterilization Procedure 44 Sterile Tank Filter 45 Vent Filter PTFE 46 Liquid Filtration 48 Filtration In Food & Beverages 49 Bag Filters Size 3 & 4 50 Bag Filter Housing Size 3 & 4 51 Bag Filters Size 1 & 2 52 Bag Filter Housing Size 1 & 2 53 Depth Filter Cartridges 54 Polypropylene Depth Filter 55 Resin Depth Filter 56 Wound Cotton Filters 57 Pleated Filter Cartridges 58 Pleated Filter Glass Fibre 59 Pleated Filter Polypropylene 60 Membrane Filter Cartridges 62 General Purpose Membrane 63 LIQUID Membrane For Chemicals 64 Membrane For Beverages 65 Nylon Membrane Filter 66 Membrane For Water Filtration 67 Single Cartridge Filter Housing 68 Plastic Filter Housing 69 Multi Cartridge Housing Doe 70 Multi Cartridge Housing Code 7 71 Mechanical Polished Filter Housing 72 High Flow Filter 74 High Capacity Filter Cartrdiges 75 Mesh Basket Filter High Flow 76 Stainless Steel Mesh Filter 77 UV Disinfection 78

3 Nitrogen Generator 80 Oxygen Generator 81 Twin Tower Nitrogen Generator 82 Twin Tower Oxygen Generator 83 Mini Nitrogen Generator 84 GAS Ultra-Pure Water Filters 86 Ultra-Pure Slim Filter Housings 87 Ultra-Pure Jumbo Filter 88 Ultra-Pure Jumbo Housing 89 Scale Filter For Machines 90 DRINKING WATER Finding The Right Size Dryer 92 Water Content In Air 94 Compressor Capacity 95 Compressed Air Filtration 96 Liquid Filtration 97 End Cap Configurations 98 GUIDES Icon Guide Material(s) For filter elements this is describing the filter media. Surface Roughness The roughness of the filter housing surface. Described in µm. Inlet/Outlet Connection Refer to the table if the filterhousing has various connection sizes. End Cap See guides for overview of end caps. O-ring Material Describes the standard o-ring. We can supply different materials. Certificate(s) FDA or PED? You find any certificate here. Dimensions For filter elements this describes the length. Diameter The cartridge diameter of filter elements. Pressure Recommended max. pressure unless otherwise described. Temperature Recommended max. temperature unless otherwise described. Flow Recommended max. flow unless otherwise described. Filtration Rate The micron rating of the filter element. Effectivity Describes the retention of particles equal to the micron rating. Differential Pressure Recommended max. diff. pressure unless otherwise described. Dew Point Describes the achievable dew points.

4 Ultrafilter Scandinavia offers a wide selection of filtration products for compressed air, liquids and gas. We have stock in Denmark and from here we distribute all of our products to Scandinavia and the Baltic countries. Ultrafilter Scandinavia is a part of the Ultrafilter Group. Production is in Germany and we have several subsidiaries in Europe and the United States. In all countries, you can buy our products on local websites. Information about our products as well as brochures and manuals can be found on our website. We can adapt all of our filtration products to your needs, and we offer visits from our consultants in order to find the right solution for you. We also offer on going service on our products once they are installed. We have many different kinds of compressed air filters that are compatible with compressed air systems of all brands. We also offer compressed air dryers, adsorption and membrane dryers in addition to auto drain compressors, compressed air tanks and oil-water separators. Additionally, we have a sterile compressed air filter for food and beverage applications. We offer all kinds of filters for liquids such as bag filters, absolute filters and membrane filters, with industrial applications, such as coolant. We have a great deal of experience with filter solutions for the food and beverage industry, and our products are approved by EC 1935/2004 as well as FDA. We also have filters for drinking water. We have one of the best generators for manufacturing nitrogen and oxygen and for filtering all kinds of gas like methane and bio gas. Ultrafilter design and manufacture components and systems for the purification of compressed air, technical gases and liquids. 4

5 Ultrafilter Skandinavien ApS - Sunekær 1, DK 5471 Søndersø - Tlf info@ultra-filter.com 3

6 COMPRESSED AIR Compressed air contains water, oil and particles, therefore it is a good idea to filter your compressed air before it is used in production, the quality of the compressed air depends on how and where you need to use it. Ultrafilter offers all types of compressed air and technical gas filtration. At Ultrafilter we have extensive experience with compressed air and compressed air filters. We stand ready to draw on this experience, if you need advice and guidance in connection with compressed air. We help you find the air filter to suit your compressed air system, and which comply with industry and customer requirements. To achieve compressed air of high quality we need to remove the oil, water and particles from the air. On the illustration below you can see how the different filters affects the compressed air. 6

7 ISO We use ISO as a reference when choosing compressed air filters, and to find out to which level it is necessary to clean the air. ISO contains particles class, water class and oil class. When refering to an ISO class, the classes are written in that order. As an example: ISO class Class Particles pr. m³ 0,1-0,5 µm 0,5-1 µm 1-5 µm Water content Residual Oil Content ,003 ppm 0,01 mg/m³ ,15 ppm 0,1 mg/m³ ,88 ppm 1 mg/m³ ppm 5 mg/m³ ,8 ppm 6 9,4 ppm Application Particle Class Water Class Oil Class General automatic Blown air Laser cutting Paints Machines with automation Surface Sandblasting Breathing air Process Industry Automatic (cylinders, solenoid valves) General compressed air Measurement & control engineering Process air Blasting / powder transport Food Industry Automatic (cylinders, solenoid valves) Wrappers Tapping columns Air tools in the production room Ait tools in workshop

8 AIR-COOLED AFTERCOOLER UA-AIR 10 or 16 bar 200 C Steel and aluminium m³/h The aftercoolers in the UA-AIR series use ambient air to cool the output compressed air at the compressor at an output temperature of only 10 C higher than the ambient temperature. This cooling causes condensation of up to 80% of the moisture in the compressed air. The condensate is then gathered and discharged in the cyclone, installed at the aftercooler outlet. The aftercoolers are made up from a heat exchanger a with finned coil, cooled by a high-efficiency axial fan mounted on a galvanized and painted sheet structure. 8 Model Flow m³/h Level Controlled Drain Connection UA-AIR /4 1/2 UA-AIR /4 11/4 UA-AIR UA-AIR /2 21/2 UA-AIR UA-AIR DN100 DN100 Based on specific operation conditions. For accurate dimensioning contact Ultrafilter. In Zero Loss Drain Out

9 WATER-COOLED AFTERCOOLER UA-WATER 10 or 16 bar 200 C Steel m³/h Aftercoolers from the UA-water series allow the efficient purification of compressed air by cooling the air at the outlet of the compressor at an outlet temperature of only 10 C higher than that of the inlet process water. This cooling causes condensation of up to 80% of the moisture present in the compressed air, which can be separated out of the air by the cyclone installed at the outlet of the cooler. UA-Water has a robust design suited to the extreme conditions of typically industrial tasks; Carbon steel vessel with copper tubes, which can also be used for seawater. Model Flow m³/h Level Controlled Drain In Connection UA-WATER /2 UA-WATER /2 1 UA-WATER UA-WATER UA-WATER /2 21/2 Zero Loss Drain UA-WATER DN80 DN80 UA-WATER DN125 DN125 UA-WATER DN150 DN150 UA-WATER DN200 DN150 UA-WATER DN200 DN200 UA-WATER DN250 DN200 Based on specific operation conditions. For accurate dimensioning contact Ultrafilter. Out 9

10 COMPRESSED AIR FILTER AG AG standard filter housings are designed for the purification of compressed air and gases in an industrial operation. This product series offers 14 different housings ranging from a volume flow of 20 m³/h to 2880 m³/h (related to 1 bar and 20 C). We offer you 10 years working guarantee. The housings are made out of three parts and due to an optimized construction, offer low differential pressures at high flow rates and as a standard equipped with a manometer and a float type drain. Other drains and accesories available. ACCESORIES FOR AG FILTER Aluminium 16 bar 65 C Perbunan Gasket SB, PE, FF, MF, SMF, AK & AKK Features & Benefits BSP or NPT Connection Low differential pressure (>50mbar) Manometer Float Drain Level Controlled Drain Timer Drain AG ¼ 02/05 AG ⅜ 03/05 AG ⅜ 03/10 AG ½ 04/10 AG ½ 04/20 AG ¾ 05/20 AG /25 AG ¼ 07/25 AG ½ 07/30 AG /30 AG /30 AG ½ 20/30 AG /30 AG /50 Correction factor: Operating pressure bar Correction factor K1 0,25 0,36 0,5 0,6 0,75 0,9 1 1,1 1,2 1,4 1,5 1,6 1,75 1,9 2 2,1

11 FILTER HOUSING WITH FLANGES SG SG filter housing series with bottom opening for easy maintenance and exchange of filter elements. For higher filtration efficiency with Ultrafilter High Performance filter elements. The SG filter housing offer minimal pressure loss due to improved flow technology and we guarantee the filter a long life thanks to the resin coating and the automatically controlled, level sensing float drain. The SG filter housing comes with flange connections from DN50 to DN300. Max. operating pressure: 16 bar. Steel 16 bar (25 bar option) 120 C Perbunan Gasket SB, PE, FF, MF, SMF, AK & AKK Features & Benefits Flange DN / ANSI Connection Low differential pressure (>50mbar) ACCESORIES FOR SG FILTER Manometer Zero Loss Drain Level Controlled Drain Timer Drain Model Correction factor: Flow m³/h Connection in/out Size Filter Element SG DN 50 15/30 1 SG DN 65 20/30 1 SG DN 80 30/30 1 SG DN 80 30/50 1 SG DN /30 3 SG DN /30 3 SG DN /30 4 SG DN /30 6 SG DN /30 8 SG DN /30 10 SG DN /30 12 SG DN /30 16 SG DN /30 20 Operating pressure bar Correction factor K1 0,25 0,36 0,5 0,6 0,75 0,9 1 1,1 1,2 1,4 1,5 1,6 1,75 1,9 2 2,1 Qty 11

12 HIGH PRESSURE FILTER HOUSING HD Aluminium or carbon steel 25, 40, 64, 100, 250 or 400 bar -10 to +80 C Perbunan Gasket SB, PE, FF, MF, SMF, AK & AKK The Ultrafilter HD high pressure filter housings are designed for the purification of compressed air and gases. Due to the modular design of the housings different filter elements can be used. A multitude of housings with different connections, allow to match the requirements of the application, e. g. the compressor size. This product series offers 8 different housings ranging from a volume flow of 30 m3/h to 720 m3/h, in the pressure stages PN 25 to PN 400 (related to 7 bar (ü) and 20 C). Model Correction factor: 7 bar m³/h Connection in/out Pressure PN Timer Drain Optional Filter Element HD / /05 HD / /10 HD / /20 HD / /20 HD /25 HD / /25 HD / /30 HD /30 Operating pressure bar Correction factor K

13 PREFILTER ELEMENTS SB / PE PE: Polyethylene. SB: Stainless Steel PE: 25 µm. SB: 1, 5 or 25 µm 99% -20 C to +80 C (PE) or +120 C (SB) Max C Aluminium end caps Perbunan Gaskets Ultrafilter offers filter elements for most compressed air applications. These high quality filter elements are made with the finest pleating technology and aluminum endcaps. Unique to the industry with their extremely low differential pressure. PE elements are made of a sintered polyethylene filter media and guarantee absolute retention rates. By using various filtration mechanisms such as direct impact and sieve effect contaminants down to the size of 25 μm are being retained. The SB is a prefilter, developed for retention of particles and liquids out of compressed air. The sintered stainless steel filtration material assures high thermal durability. Ultrafilter offers filter elements for most compressed air applications. These high quality filter elements are made with the finest pleating technology and aluminum endcaps. Unique to the industry with their extremely low differential pressure. RECOMMENDED FILTER HOUSINGS AG SG HD 13

14 MICROFILTER ELEMENTS FF / MF / SMF Ultrafilter offers filter elements for most compressed air applications. These high quality filter elements are made with the finest pleating technology and aluminum endcaps. Unique to the industry with their extremely low differential pressure. The FF/MF/SMF filter elements are made with a pleated oleophobic filter media that rejects oil and water. Borosilicate, cerex and polyurethane 0,01 µm Advanced pleating techniques Perbunan Gaskets mixed with nano technology, makes Features & Benefits our High Performance filters much Low differential pressure entire lifetime more effective than a standard filter, as the pleating provides a 450% larger filtration surface per square inch. The special pleating also secures a much larger particle retention capacity. 99% 80 C (available up to 180 C) Max C Aluminium end caps The benefits of using this type of filter is low differential pressure, up to 70% lower energy costs and improved efficiency of filtration. RECOMMENDED FILTER HOUSINGS AG SG HD Type Filtration rate Effectivity Residual oil content Start-up differential pressure FF 0,01 µm 99,999% 0,1 mg/m³ 0,04 bar MF 0,01 µm 99,99998% 0,03 mg/m³ 0,08 bar SMF 0,01 µm 99,99999% <0,01 mg/m³ 0,09 bar 14

15 ACTIVATED CARBON ELEMENTS AK / AKK Activated Carbon and Borosilicate C Max C Aluminium end caps Perbunan Gaskets Residual oil content: < 0,003 mg/m³ Lifetime: hours (AK) hours (AKK) AKK AK Ultrafilter offers filter elements for most compressed air applications. These high quality filter elements are made with the finest pleating technology and aluminum endcaps. Unique to the industry with their extremely low differential pressure. The AK filter elements consist of a two-stage filtration. All particles are kept in a nanofiber depth filter media, while the activated carbon adsorbs all oil vapors and gaseous hydrocarbons. Ultrafilter offers filter elements for most compressed air applications. These high quality filter elements are made with the finest pleating technology and aluminum endcaps. Unique to the industry with their extremely low differential pressure. RECOMMENDED FILTER HOUSINGS AG SG HD 15

16 ALTERNATIVE ELEMENTS Our series of cross over elements makes it possible to use our high quality filters in filter housings from different manufactures. We are mostly using the same pleating mixed with nano technology in all the cross over elements we offer. Domnick Hunter Evolution Domnick Hunter Oil-X Hiross Atlas Copco Zander Hankison Deltech Walker Donaldson Kaeser Stenhøj BEKO BY REQUEST ALSO Compair Ceccato Ingersoll Rand ALUP ALMiG Pneumatech Chicago Pneumatic MARK BOGE PLEATED MEDIA TECHNOLOGY 16

17 ALTERNATIVE ELEMENTS ISO Class ( ) Prefilter Prefilter Microfilter Submicrofilter Activated Carbon * Ultrafilter PE FF MF SMF AK Domnick Hunter Evolution Domnick Hunter Oil-X - AR, AO AAR AA ACS - AO AA AX AC, ACS Hiross Q P S - C Atlas Copco - DD PD - QD Zander V Z Y X A Hankison E9 E7 E5 E3 E1 Donaldson PE FF MF SMF AK Deltech - DFD PFD HFD CFD Walker X25, X5 X1 XA - AC CompAir - B+E C+F - D Ceccato - P G C V Kaeser E-B E-C E-E E-F E-G Stenhøj PE FF MF SMF AK ALUP - P G C V ALMiG AFP AFM AFS - AFC Pneumatech - P G C V Chicago Pneumatic - P G C V BEKO G F S - A MARK - P G C V BOGE V - FP - A Type Particle Filtration rate Effectivity Residual oil content Max. differential pressure PE 25 µm 99% N/A 2 bar at 20 C SB 25 µm 99% N/A 2 bar at 20 C FF 0,01 µm 99,999% 0,1 mg/m³ 5 bar at 20 C MF 0,01 µm 99,99998% 0,03 mg/m³ 5 bar at 20 C SMF 0,01 µm 99,99999% <0,01 mg/m³ 5 bar at 20 C AK Activated Carbon N/A 0,003 mg/m³ 2 bar at 20 C 17

18 ACTIVATED CARBON TOWER Ultra-Sorp AKC The activated carbon adsorber is designed to ensure oil- and odourfree compressed air. Compressed air is lead through and activated carbon bed and ensures a residual oil content of < 0,003 ppm. The residual oil ontent depends on the inlet conditions. A residual oil content of < 0,003 ppm is related to an operating pressure of 7 bar (g), 35 C inlet temperature, and predried compressed air with a dewpoint of -40 C, as well as a prefiltration of particles < 0,03 mg/m3. 4 to 16 bar Max. 50 C m³/h Features & Benefits Operating lifetime: 8000 hours Residual oil content: < 0,003 ppm Model Flow m³/h Connection in/out Dimensions (mm) Height Width Depth AKC / AKC / AKC AKC AKC AKC / AKC / AKC / AKC AKC AKC AKC Correction factor: Operating pressure bar Correction factor K1 0,63 0,75 0,88 1,00 1,10 1,20 1,35 1,44 1,50 1,60 1,75 1,86 2,00 Inlet temperature C Correction factor K2 0,80 1,00 1,25 1,50 18

19 MEASURING INSTRUMENTS Ultrafilter has a wide range of measuring equipment for compressed air. The range includes dew point sensors, flow sensors, leakage detectors as well as oil vapour sensors and laser particle counters. DEW POINT SENSORS UF C to 0 C UF C to +20 C UF C to +20 C UF C to +50 C FLOW SENSORS AIR QUALITY UF400 Insertion Type UF420 Inline Type Oil Vapour Sensor Laser Particle Counter 19

20 OIL / WATER SEPARATOR Ultra-Sep ABS or PE LGA Features & Benefits Up to 12 m³/min compressor capacity 3-stage filtersystem Compact design The production of compressed air always generates condensate water too. The amount of condensate depends of the size and the number of operating hours of the compressor and can easily range from 10 to liter condensate per month. Such condensate water from oil-lubricated compressors may contain up to mg oil per liter. Environmental protection legislation already requires, or will soon require condensate water to be cleaned from oil before it is discharged into the public sewage system. In countries with such legislation for Water Resources Conservation, the limit-value is set at 20 mg oil per liter of condensate water. If the condensate is not discharged oil-free, it must be collected and treated by an approved waste oil treatment company. The Ultra-Sep removes the oil from condensate water on efficiently and reliably - by calming the water and utilizing a series of coalescence- and activated carbon filters. The condensate water is now so clean, that it can be discharged into the public sewage system. The oil is being collected in an oil-container and can be handled and disposed separately and safely. Model Compressor capacity Connection m³/min kw In Out Ultra-Sep 1 1,8 13,0 1/2 x3 1 Ultra-Sep 2 2,5 15,0 1/2 x3 1 Ultra-Sep 3 3,5 22,0 1/2 x3 1 Ultra-Sep 6 6,0 37,0 1/2 x4 1 Ultra-Sep 8 10,0 65,0 1/2 x4 1 Ultra-Sep 10 12,0 75,0 1/2 x4 1 20

21 ACTIVATED CARBON BAGS Ultrafilter offers a complete range of oil/water separator maintenance kits for competitor oil/water separators. Producer Suitable for BEKO (BOGE) Atlas Copco Kaeser Ecoair Schneider Öwamat 1/2 OSW 5/11 Aquamat 1/2 - Owatec 10/40 Öwamat 3 - Aquamat 3 TS 3 - Öwamat 4 OSW 30 Aquamat 4 TS 4 Owatec 130 Öwamat 5 - Aquamat 5 TS 15 - Öwamat 5R OSW 55 Aquamat 5R - Owatec 175 Öwamat 6 OSW 110 Aquamat 6 TS 16 Owatec 250 Öwamat 8 OSW 315 Aquamat Öwamat Öwamat Öwamat 20 - Aquamat 20 TS 60 - Wortmann Producer Zander Wortmann/ Kaeser Suitable for Hankison Zander Drukomat 1/MINI Ekolog 1/Mini HS1 HS 60, 70, 120 Ecosep S1/MINI Drokumat 2 Ekolog 2 WOI-II HS2 HS Ecosep S2 Drukomat 4 Ekolog 4 WOI-II HS3 HS Ecosep S4 Drukomat 8 Ekolog 8 WOI-II HS4 HS Ecosep S8 Drukomat 15 Ekolog 15 WOI-II* HS5* HS * Ecosep S15 Drukomat 30 Ekolog 30 WOIII HS6 HS 1800 Ecosep S30 Drukomat 61 Ekolog 61 WOIV HS7 HS 3600 Ecosep S61 21

22 REFRIGERATION DRYER 50Hz Ultra-Pulse UD Standard: 16 bar Max. Ambient: 50 C Max. Inlet: 70 C m³/h Dewpoint: 3-9 C 230/1/50 or 400/3/50 Refrigerant fluids: R134a or R404A With the introduction of ultra.dry, the new generation of energy-saving refrigeration dryers has arrived. The new ultra.pulse technology offers important advantages in terms of energy saving, reliability and operating costs as the ultra.dry dryer is able to adapt itself to the real needs of the compressed air system. The regulation system of the dryer controls the dryer operation granting the most energetically effective method of compressed air drying, achieving high energy saving and ensuring at the same time an excellent dew point stability also in dynamic condition. High maximum inlet temperature up to +70 C (ultra.dry UD ) +60 C (ultra.dry UD ) and maximum ambient temperature (+50 C) ensure a fail-safe operation at all times. The standard ultra.dry refrigeration dryer has a high operational pressure limit of 16 bar. 22 Model Flow m³/h Connection in/out Power V/ph/Hz UD /8 230/1/50 UD /8 230/1/50 UD /8 230/1/50 UD ½ 230/1/50 UD /2 230/1/50 UD /1/50 UD /1/50 UD /1/50 UD /1/50 UD ½ 230/1/50 UD ½ 230/1/50 UD /2 230/1/50 UD /2 230/1/50 UD /1/50 UD /1/50 UD ½ 230/1/50 UD ½ 400/3/50 UD ½ 400/3/50 Based on specific operation conditions. For accurate dimensioning see our guide page 92.

23 REFRIGERATION DRYER 60Hz Ultra-Dry UD Standard: 16 bar Max. Ambient: 50 C Max. Inlet: 70 C m³/h Dewpoint: 3-9 C 115/1/60 or 230/1/60 Refrigerant fluids: R134a or R410A Some industries and countries use higher frequency power as their standard 60 Hz instead of the European standard, 50 Hz. Some equipment can function on either frequency, and a range of voltage, however for most critical industrial machinery, a set frequency and voltage on the equipment are required to guarantee the stability of the production with the equipment. Such industries count many marine and off-shore installations, and projects in or from North America, and we have a complete range of refrigeration dryers for 60 Hz installations. These refrigeration dryers come with the usual benefits of our normal range of refrigeration dryers. Model Flow m³/h Connection in/out Power V/ph/Hz UD-60Hz ½ 115/1/60 UD-60Hz ½ 115/1/60 UD-60Hz ½ 115/1/60 UD-60Hz /1/60 UD-60Hz /1/60 or 230/1/60 UD-60Hz /1/60 UD-60Hz /1/60 UD-60Hz /1/60 UD-60Hz /1/60 Based on specific operation conditions. For accurate dimensioning see our guide page

24 HIGH PRESSURE REFRIGERATION DRYER Ultra-Dry HP Standard: 50 bar Max. Ambient: 45 C Max. Inlet: 70 C m³/h Dewpoint: 3-9 C 230/1/50 or 400/3/50 Refrigerant fluids: R134a or R407C UD-HP has been specifically designed for the needs of the high pressure dryer User, offering working pressures of up to 50 barg. The extremely reliable design concept ensures that UD-HP operates perfectly at all times and in all conditions. UD-HP automatically adopts its operation to the air flow and ambient conditions, offering energy savings of up to 80% compared with traditional dryers. UD-HP forms part of a complete range of Ultrafilter products for higher pressures, ensuring all User needs are perfectly satisfied. Model Flow m³/h Connection in/out Nominal absorbed power (kw) UD0045HP 45 1/2 0,17 UD0090HP 90 1/2 0,25 UD0240HP 240 1/2 0,46 UD0370HP ,71 UD0480HP ,76 UD0600HP ,97 UD1100HP /2 1,78 UD1450HP ,20 UD1530HP /2 3,09 UD1960HP /2 4,29 UD2700HP ,44 UD3700HP ,39 UD4500HP ,72 UD6100HP ,42 UD7300HP ,16 Based on specific operation conditions. For accurate dimensioning see our guide page

25 MEMBRANE DRYER Ultra-Dry UFM UFM membrane dryer are well suited for point of use applications and for small volume flows. Designed with ease-of-installation and operation in mind, the inlet and outlet are provided as easy-to-install BSP thread connections. The compressed air flows through a bundle of hollow fibers. As the humid compressed air flows down the bore of the fiber, water vapor diffuses through the walls of the fibers. At the outlet of the unit, a small volume of the dry compressed air is expanded and released into the space surrounding the outside of the fibers. The dry air sweeps the moisture away from the outside of the fibers and exhausts to the atmosphere as a humid air stream. Max. 12,5 barg Max. 60 C m³/h Reduces dewpoint: C Each membrane dryer is equipped with a calibrated purge air blend. No further adjustments are necessary. The UFM membrane dryer doesn t release any fibers and is suitable for medical air applications. Our membrane dryers are extremely efficient due to their new, improved hollow fiber technology. Even with low pressure dewpoints, only a relatively small purge air requirement is necessary. 25 Model Purge air (m³/h) Connection in/out 15 C DP (m³/h) 3 C DP (m³/h) -20 C DP (m³/h) -40 C DP (m³/h) In Out In Out In Out In Out UFM ,3 1/4 3,0 2,7 2,2 1,9 1,4 1,1 1,0 0,7 UFM ,6 1/4 6,0 5,4 4,3 3,7 2,8 2,2 2,0 1,4 UFM ,96 1/4 9,0 8,04 6,4 5,44 4,3 3,34 3,1 2,14 UFM ,14 1/4 12,0 10,86 8,5 7,36 5,7 4,56 4,1 2,96 UFM ,74 1/2 18,0 16,26 12,8 11,06 8,5 6,76 6,2 4,46 UFM ,28 1/2 24,0 21,72 17,1 14,82 11,3 9,02 8,2 5,92 UFM ,42 1/2 36,0 32,58 25,6 22,18 17,1 13,68 12,4 8,98 UFM ,56 1/2 48,0 43,44 34,1 29,54 22,7 18,14 16,4 11,84 UFM ,18 1/2 64,0 57,82 44,8 38,62 29,8 23,62 21,6 15,42 UFM /2 90, ,2 58,2 43,8 34,8 31,5 22,5 UFM ,5 1/2 125,0 112,5 91,8 79,3 58,8 46,3 42,6 30,1 UFM , ,1 110,1 85,5 67,5 61,5 43,5 Based on specific operation conditions. For accurate dimensioning see our guide page 93.

26 HEATLESS ADSORPTION DRYER HeatLess HL Standard: 16 bar (25 bar optional) Max. Inlet: 50 C m³/h Dewpoint: -40 C up to -70 C 230V 50Hz (115V 60Hz optional) Features & Benefits Pre- and after filter included Galvanized in- and outlet DRYER OPTIONS Dewpoint Measurer Bypass ATEX Anti Freezing Trace Heating 26 Cabinet Version Oil Free Version Breathing Air Version Siemens PLC

27 HEATLESS ADSORPTION DRYER HeatLess HL As a complete system the HeatLess HL adsorption dryer has a prefilter (with automatic condensate drain), silencers and an integrated dust filter onboard providing maximum efficiency and operational safety. HeatLess HL adsorption dryer are produced for a wide range of applications and are delivered ready to connect and easy to install. Standard pressure 16 bar, up to 25 bar optional. Model Flow m³/h Connection in/out Dimensions (mm) Width Depth Height HL G¾ HL G¾ HL G HL G HL G HL G1 ½ HL G1 ½ HL G1 ½ HL G HL G HL G HL G2 ½ HL DN HL DN HL DN HL DN HL DN HL DN HL DN HL DN HL DN HL DN HL DN HL DN Based on specific operation conditions. For accurate dimensioning see our guide page

28 COMPACT ADSORPTION DRYER Ultra-Dry Compact UDC 4-16 bar Max. 50 C m³/h Dewpoint: -40 C up to -70 C VDC, VAC The UDC is our most compact dryer. The integrated prefilter retains particles and oil. Condensate is drained securely and efficiently by an integrated condensate drain. The subsequent adsorption dryer removes moisture from the compressed air up to a pressure dewpoint of -40 C (optionally -70 C). Regeneration and drying is made in two parallel installed vessels. Dust particles out of the desiccant are retained in the included afterfilter. Model Flow m³/h Connection in/out Dimensions (mm) Height Width Depth Prefilter MF Size UDC / /05 UDC / /05 UDC / /05 UDC / /05 UDC / /05 UDC / /05 UDC / /05 UDC / /20 UDC / /20 UDC / /20 UDC /20 UDC /20 UDC / /25 UDC / /25 UDC / /30 UDC / /30 UDC /30 Based on specific operation conditions. For accurate dimensioning see our guide page

29 HIGH PRESSURE AIR DRYER 40 BAR EM AIR B 50 G H C F 16 or 40 bar Max. 50 C m³/h Dewpoint: -20 C up to -60 C 230 V, 50 or 60Hz E A We offer 6 different heatless adsorption dryers for compressed air up to 40 bar. For these dryers we recommend our HD high pressure filter housings as pre and after filter. HD Filter Housing Prefilter MF Afterfilter PE Siemens PLC 230RC Model Flow m³/h Connection in/out Dimensions (mm) A B C D E F G EM 10 14,4 3/ EM 15 18,0 3/ EM 25 23,4 3/ EM 40 35,4 3/ EM 60 58,8 3/ EM 90 78,6 3/ Based on specific operation conditions. For accurate dimensioning contact Ultrafilter. 29

30 HEAT REGENERATED DRYER VarioBlo 4-10 bar (25bar option) Max. 43 C m³/h Dewpoint: -20 C up to -70 C 380 V V / 50 Hz - 60 Hz Features & Benefits Siemens PLC S7 Zero purge DRYER OPTIONS Dewpoint Measurer Bypass ATEX Anti Freezing Trace Heating 30

31 HEAT REGENERATED DRYER VarioBlo The VarioBlo adsorption dryer is a heat regenerated dryer and manage regeneration without any compressed air consumption. The VarioBlo dryer uses a frequency controlled blower to regenerate the dryer by heat. The dryer is equipped with a Siemens PLC and is highly customizable. Standard working pressure is 8 bar and up to 25 bar as an option. 3 standard versions: - HRE - VarioBlo - Compheat Model Flow m³/h Connection in/out Dimensions (mm) Width Depth Height Installed Power kw VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN VarioBlo DN Based on specific operation conditions. For accurate dimensioning see our guide page

32 COMPRESSED AIR RECEIVER Painted, Galvanized or SS or 16 bar (23 and 41 optional) Available Certificates SPVD 2009/105/EC PED 97/23/EC ASME Sect. VIII Div. 1 / Div. 2 ISO 9001:2008 Dir. 2014/68/EU (CE 003) AD 2000 Merkblaetter Our compressed air receivers are designed to store compressed air. The vessels are manufactured in Germany to the highest quality standards. On request we can also deliver vessels designed for any other technical gas. The vessels are availed in three materials: Galvanized, painted and stainless steel. We offer receivers for pressure: 11, 16, 23 or 41 bar. RECEIVER ACCESORIES Safety Valves Complete Receiver Kit Manometer Vent Filter 32

33 COMPRESSED AIR RECEIVER Finding the right receiver, based on airflow Airflow Capacity m³/h Recommended receiver voume liters Compressed Air Vessel Volumes Liters Painted 11 bar H Painted 11 bar V Painted 16 bar H Painted 16 bar V Galvanized 11 bar H Galvanized 11 bar V Galvanized 16 bar H Galvanized 16 bar V SS bar V H = Horizontal. V = Vertical Compressed Air Vessel Volumes Liters Painted 11 bar H Painted 11 bar V Painted 16 bar H Painted 16 bar V Galvanized 11 bar H Galvanized 11 bar V Galvanized 16 bar H Galvanized 16 bar V SS bar V H = Horizontal. V = Vertical 33

34 BREATHING AIR FILTER SYSTEM Users: 1-4 (based on 250 l/min pr. user) Inlet: 3/8 Outlet: 1/4 Elements: MF 03/10 and AK 03/10 Mounting: Wall brackets or floor stand Made to the standards of the Danish working enviroment authority regulation D.5.1 and EN Filtered compressor air from a compressor can be used where there is a low oxygen concentration (less than 17% vol.) Or the ambient air is not suitable for breathing air. Ultrafilters new breathing air panel with SMF & AK filter (oil and particle filter and carbon filter) is used for filtration of compressed air from the compressor and compressed air dryer, this product is available in two versions: Floor stand or wall mounting, both available for 1 to 4 users. Ultrafilter compressed air breathing system is made to the standards of the Danish working environment authority (arbejdstilsynet) regulation D.5.1 by July 2000 or EN It is a must to have your breathing air quality checked at least one time per year. OPTIONS FOR BREATHING AIR Ultrafilter offers air heaters for compressed air and gas filtration with or without integrated temperature measurement. Our product allows a precise temperature control from 20 C to 120 C and are suitable for industrial or breathing air applications. Additionally, we offer pressure regulators and mounting solutions for floor or wall for our breathing air filters. Air Heater Manometer Floor Mount Wall Mount 34

35 PROCES AIR STEAM P-GS AIR Class 3 (ISO ) P-SMF P-SRF

36 PROCES AIR Our sterile filters are all FDA CFR article 21 / EC 1935/2004 validated and approved. Sterile means free of microorganisms that are capable of reproducing itself. A more scientific definition of sterile is that a filter is defined as sterilizing filter, when exposed to a concentration of 107 microorganisms (Brevundimonas diminuta) per. cm² filter area and the filtrate is 100% sterile and therefore not containing microorganisms, such as bacteria. Coli and streptococci typically have a size between 0,3 microns and 9 microns, resulting in that the sterile filter has a Filtration of 0,2 microns or better. In sterile filtration of compressed air, there are differentiated between two types of filter: the depth filter (P-SRF) and membrane filter (PF-PT and PF-PP). Depth Filter A depth filter typically consists of multiple layers of metallic, polymeric or inorganic material - typically used a variety of silicon, called borosilicate. This type of filter is distinguished by a high filtration capacity and high degree of stability during use and sterilization. This type of filter is about % effective compared to a give micron size. Membrane Filter A membrane filter is made of polymeric plastic film - typically polypropylene, these filters have less particle retention capacity, which is solved by prefiltration. The membranes have a 100% retention rate and is available in several filtration degrees. For the food industry, the recommended standard is a depth filter, and for use in the pharmaceutical, fine chemical or biotech industries, we recommend membrane filters. Both filters are optimally placed close to the point of use. It is recommended that installed a central desiccant dryer as well as a coalescing micro filter and activated carbon filter, to secure dry and oil-free compressed air at the sterile filters, thereby extending the life of the filter. 36

37 PROCESS AIR PREFILTER ELEMENT P-FF / P-MF / P-SMF / P-AK Binderfree nanofibres, Pleated cerex 0,01 µm 99,999% - 99,99999% -20 C to 80 C Max C Stainless steel SS304 end caps Perbunan Gasket (others available) All our standard coalescing, particulate and activated carbon filters are available as pre-filters for our stainless steel filter housings for critical installations. Thanks to the unique combination of binder free, non-woven nanofiber filter media and our special pleating techniques, we can achieve a reduction of energy costs up to 70%, at a higher than regular efficiency. The new nanofiber material from ultrafilter is oleo phobic, which means that the oil and water particles are actively rejected in order to keep a low differential pressure drop, and consequently the operating costs are reduced to a minimum compared with a conventional filter element. All metal components on the prefilter elements are made of stainless steel. Type Filtration rate Effectivity Residual oil content Max. differential pressure P-FF 0,01 µm 99,999% 0,1 mg/m³ 5 bar at 20 C P-MF 0,01 µm 99,99998% 0,03 mg/m³ 5 bar at 20 C P-SMF 0,01 µm 99,99999% <0,01 mg/m³ 5 bar at 20 C P-AK Activated Carbon N/A 0,003 mg/m³ 2 bar at 20 C 37

38 STERILE DEPTH FILTER ELEMENT P-SRF The P-SRF is a wounded depth filter with inner and outer guard end caps made of stainless steel. Consisting of a threedimensional borosilicate depth media, the P-SRF achieves a void volume of 95%, ensuring a high containment capacity at high flow rates and low differential pressure. A retention rate of > % related to 0.2 μm is achieved during operation. Borosilicate 0,2 µm 99,99998% -20 C to 200 C Max. 5 bar Stainless steel SS304 end caps Silicone (others available) This element is STERILIZABLE See page 44 Depth Filter A depth filter typically consists of multiple layers of metallic, polymeric or inorganic material - typically used a variety of silicon, called borosilicate. This type of filter is distinguished by a high filtration capacity and high degree of stability during use and sterilization. This type of filter is about % effective compared to a give micron size. 38

39 PROCESS FILTER HOUSING P-EG P-EG filter housings in stainless steel, designed for purification of compressed air and other technical gases. With this filter you can achieve low differential pressure at high flow rates. P-EG Filter housings are available in 18 different sizes from 60 to Nm3/hour. The P-EG is our first-choice housing for most process air applications. Such as prefiltration, sterile filtration and steam filtration. SS304 or SS316L 200 C (250 C as option) EPDM seal (others on request) : 16 bar 0288: 12 bar : 10 bar 25 bar on request 39 BSP ASA (weld) DIN / ANSI Model Flow m³/h Connection in/out Filter Element BSP ASA DIN Size Qty P-EG R 1/4 DN10 DN10 03/10 1 P-EG R 3/8 DN10 DN10 04/10 1 P-EG R 1/2 DN15 DN15 04/20 1 P-EG R 3/4 DN20 DN20 05/20 1 P-EG R 1 DN25 DN25 05/25 1 P-EG R 11/4 DN32 DN32 07/25 1 P-EG R 11/2 DN40 DN40 07/30 1 P-EG R 2 DN50 DN50 10/30 1 P-EG R 2 DN50 DN50 15/30 1 P-EG R 21/2 DN65 DN65 20/30 1 P-EG R 3 DN80 DN80 30/30 1 P-EG R 3 DN80 DN80 30/50 1 P-EG N/A N/A DN100 20/30 3 P-EG N/A N/A DN100 30/30 3 P-EG N/A N/A DN150 30/30 4 P-EG N/A N/A DN150 30/30 6 P-EG N/A N/A DN200 30/30 8 P-EG N/A N/A DN200 30/30 10 Correction factor: NPT Operating pressure bar Correction factor K1 0,25 0,36 0,5 0,6 0,75 0,9 1 1,1 1,2 1,4 1,5 1,6 1,75 1,9 2 2,1

40 STERILE MEMBRANE FILTER Ultra-Mem PF-PT / PF-PP eptfe and Polypropylene 0,02 µm, 0,1 µm, 0,2 µm or 0,45 µm 99,99998% -20 C to 80 C Max C Code 7 (others available) This element is STERILIZABLE See page 44 Silicone (others available) For critical applications in sterile filtration, use of a hydrophobic PTFE membrane is recommended, especially in applications such as pharmaceutical industry and biotechnology. PTFE membranes are also well suited for sterile steam applications. For certain chemicals and applications, polypropylene membranes are available. Membrane Filter A membrane filter is made of polymeric plastic film - typically polypropylene, these filters have less particle retention capacity, which is solved by pre-filtration. The membranes have a 100% retention rate and is available in several filtration degrees. Model PF-PT PF-PT PLUS PF-PP Filtrationrates 0,02 to 0,45 µm 0,2 µm 0,1 to 0,2 µm Material eptfe eptfe Polypropylene Applications Sterile process gases Fine chemicals and solvents Photoresists and developers Biotechnology Powder handling and tabletting 40

41 SANITARY AIR FILTER HOUSING PG-EG PG-EG stainless steels have been developed for the purification of compressed air and other technical gases in pharmaceutical, biotechnology and chemical industries. PG-EG houses are first choice in critical applications in sterile filtration. All PG-EG filter housings to a certain size have been etched and passivated on the inner surface to a quality of Ra 0,8. The outer surface has this quality or better for every PG-EG sanitary filter housing. 304 or 316L 0,8 (0,4 optional) 200 C : 16 bar : 10 bar Code Y (UF) or Code 7 EPDM (others available) Tri-clamp ASME Correction factor: Model Dairy Union DIN Flow m³/h Flange EN Connection (clamp) Weld End Filter Element PG-EG DN25 05/30 1 PG-EG DN40 10/30 1 PG-EG DN50 15/30 1 PG-EG DN65 20/30 1 PG-EG DN80 30/30 1 PG-EG DN100 20/30 3 PG-EG DN100 30/30 3 PG-EG DN150 30/30 4 PG-EG DN150 30/30 6 PG-EG DN200 30/30 8 PG-EG DN200 30/30 10 Operating pressure bar Correction factor K1 0,25 0,36 0,5 0,6 0,75 0,9 1 1,1 1,2 1,4 1,5 1,6 1,75 1,9 2 2,1 Size Qty 41

42 STEAM FILTER P-GS The ultrafilter P-GS filter is designed for removal of particles from gases, liquids and particularly steam. The P-GS consists of a restorable weldless filter pipe made from sintered stainless steel. The filter is well suited for culinary steam where contact with production machines and end product is needed. The P-GS is suited for use in temperatures ranging from -20 C to 210 C and has a maximal differential pressure tolerance of 5 bar. Sintered steel SS316L 1 µm, 5 µm or 25 µm 98 (steam) / 100% (gasses) -20 C to 210 C Max. 5 bar Stainless steel SS304 end caps Code Y (UF), DOE or Code 7 EPDM (others available) OPTIONS Viton Seal Fluoraz Seal Silicone Seal Welded End Caps Applications 1 µm 5 µm 25 µm Food Contact General use of steam Pre-filtration of steam 42

43 FILTER HOUSING FOR STEAM P-EG For our PG-S steam filters we use our P-EG filter housing with flange connections. With this filter you can achieve low differential pressure at high flow rates. P-EG Filter housings are available in 12 different sizes, in either 304 or 316 stainless steel. For particularly high quality demands, we offer our sanitary filter housing PG-EG for steam filtration. SS304 or SS316L 1,2 200 C : 16 bar 0288: 12 bar : 10 bar 25 bar on request EPDM seal (others available) Model Flow (kg/h) 1 µm 5 µm 25 µm Connection DIN Filter Housing Element Size P-GS DN10 P-EG /10 P-GS DN10 P-EG /10 P-GS DN15 P-EG /20 P-GS DN20 P-EG /20 P-GS DN25 P-EG /25 P-GS DN32 P-EG /25 P-GS DN40 P-EG /30 P-GS DN50 P-EG /30 P-GS DN50 P-EG /30 P-GS DN65 P-EG /30 P-GS DN80 P-EG /30 P-GS DN80 P-EG /50 Flow rate at 121 C saturated steam Correction factor: Operating pressure bar Saturated steam temp. C Correction factor K1 0,

44 STERILIZATION PROCEDURE Both depth and membrane sterile filters can be sterilized in-line with steam or externally by autoclave. It is recommended to sterilize a sterile filter after every production batch or at least after 14 days. Sterilization temperature is between 110 C C, respectively for 30 and 10 min. 1. Valve (1) and valve (4) closes. 2. Drain valve (2) opens. 3. Valve (3) opens and steam flow into the filter housing. 4. After reaching a temperature of 100 C, the steam begins to condense at the same time that there is only opened to the valve (2), the pressure being built up to the desired sterilization temperature. 5. After reaching the steam temperature starts the actual sterilization within the ages: Saturated steam 121 C - 30 minutes Saturated steam 131 C - 20 minutes Saturated steam 141 C - 10 minutes When sterilization rounded cast of valve (2), after which valve (3) & (1) open slowly and valve (4) closes slowly - and then start the process over again. 44

45 STERILE TANK FILTER P-BE Borosilicate, stainless steel housing 0,2 µm 99,999% -20 C to 200 C This element is STERILIZABLE See page 44 Stainless steel SS304 end caps Silicone (others available) P-BE filter are used to ensure 100% sterility in the storage vessels of pharmaceutical products, chemicals, food or of fermenters. The filter acts as sterile breather for the content of the vessel. The P-BE is a depth filter and works both ways, and protects the surrounding area from exposure to the contents of the vessel. The two-part housing is user-friendly designed and has a splash protection to prevent liquids coming in contact with the filter media. The filter element can be sterilized for continuous use up to 100 times. Regeneration is done by in-line steam or externally in autoclave. Model Flow (m³/h) Filter Element Connection* p = 20 mbar p = 40 mbar Size Qty P-BE DN32 03/10 1 P-BE DN40 05/25 1 P-BE DN50 05/30 1 P-BE DN50 10/30 1 P-BE DN80 20/30 1 P-BE DN80 30/30 1 P-BE DN100 20/30 3 P-BE DN100 30/30 3 P-BE DN150 30/30 4 P-BE DN150 30/30 6 P-BE DN200 30/30 8 P-BE DN200 30/30 10 *Milk Pipe fitting acc. DIN or flange acc. DIN

46 VENT FILTER PTFE Ultra-Vent eptfe and Polypropylene 0,1 µm or 0,2 µm 99,99998% 80 C Max C 1/2 BSP male thread Silicone Gasket (others available) 2,5 or 5 Our PTFE Vent filter cartridges are manufactured using a highly hydrophobic eptfe membrane and are designed for autoclave venting and small vessel venting. The enhanced eptfe membrane offers exceptionally high gas flow rates at low pressure differentials. The vent filter cartridges are designed with a ½ BSP male thread for autoclave and small vessel venting applications, and the hydrophobic characteristics of the eptfe membrane makes the Vent filter cartridge particularly suitable for rapid vacuum breaks in autoclaves. Model Filtration Rate Connection Dimensions (mm) Length Diameter Ultra-Vent 2,5 0,2 µm 1/ Ultra-Vent 5,0 0,2 µm 1/

47

48 LIQUID FILTRATION Liquid filtration today is for everything from ingredients and final products to wastewater and cooling water. The filtration degree can range from a millimeter, and to sterilizing grades below 0.2 micron. We offer various filtration techniques and materials to meet our concept of Total Filtration Management. We have filter housings in stainless steel or various plastics, as well as a long range of filter elements from spun cotton to pharmaceutical membranes. In this area of our catalogue, you are able to read about some of the various materials and techniques we utilize in liquid filtration, from our industrial grade high-flow filters, to our FDA and EC approved filtration solutions for high requirement tasks. Filtration Process Range Application Example Particle Filtration µm General Industry Microfiltration 1-0,1 µm Food and Beverage Ultrafiltration 0,1-0,001 µm Pharmaceutical Nanofiltration < 0,001 µm 48

49 FILTRATION IN FOOD & BEVERAGES Besides specific pharmaceutical grade requirements, you find some of the highest quality demands in the FDA approval by CFR article 21, and the European EC 1935/2004, commonly known as the food and beverage certifications. The Pioneers of liquid filtration, the food and beverages industry, have long held high demands for sterile filters, prefilters and even process water filtration, to reduce the risk of any contamination of product or employees, and with standardization of the requirements, the demands have not gotten any less specific or easier to meet, but our product range have been designed to fit your highest expectation, from our high capacity filter bags, to the highest efficiency membrane filters. The bulk of the range is sold for stainless steel filter housings, although we offer a long range of FDA and EC approved polypropylene filter housings, as well as steel housings in both 304 and 316 stainless steel housing. You can find filter elements for any application, and for food and beverages we have PES filters for wine, beer or bottled water, as well as a long range of general purpose filters for milk, ingredient saltwater, enzymes, viscous liquids and many more. 49

50 BAG FILTERS SIZE 3 & 4 Ultra-Bag PP / PE / NMO Polypropylene, Polyester or Nylon 1 to 1200 µm 80% 10cm Size 3: 25 cm, Size 4: 40 cm PP: 82 C. PE: 120 C. NMO: 90 C Features & Benefits Top ring of polypropylene, polymer or stainless steel. The filter bags distinguish themselves by high flow capability and dirt holding capacity. They come in a broad selection of filtration degrees from 1 to 200 micron in polypropylene and the high temperature polyester bags. We also carry Nylon bags for rough filtrations up to 1200 microns. Less than 30% particles can pass through a bag filter of the same filtration degree. All bags are available as FDA and EC certified version with polypropylene fixture, as well as with a steel ring fixture version for industrial applications. Polypropylene and polyester bags utilize the depth filtration technique, trapping various particles and oil remnants in the fibers of the material, however the nylon material is a mesh filter bag, meaning it s a surface filtration, often used for more viscous liquids or coarser filtration degrees. Bag material Polypropylene Polyester Nylon Ring material PP SS PM SS PM SS Food Beverages High viscosity Process Water - Over 80 C PP = Polypropylene. SS = Stainless Steel. PM = Polymer Size 3 Diameter: 10cm Length: 25 cm Flow: 100 l/min Size 4 Diameter: 10cm Length: 40 cm Flow: 150 l/min Filtration rate µm Material PP PE NMO 50

51 BAG FILTER HOUSING SIZE 3 & 4 Ultra-Wound AISI 304 or AISI l/min 10 bar -10 to +90 C FPM Gasket (others available) OPTIONS The filter housings of the ALSI series (size 3/4) are welded stainless steel constructions to the admission of a filter bag of the size 3 or. the size 4. They exist of a vertical, cylindrical shell with welde protection split pin, therefore the lid during of the filtration process cannot be opened uncontrollably. The filter bag is fixed in the housing by a down holder in his situation reliably and is sealed. The supporting basket from stainless steel provides for a support sure about pressure of the used filter bag. Clamp Closing Swing Bolt Closing Model Flow l/min Connection in/out Bag size Dimensions (mm) A B C D E F ALSI ½ ±5 60 ø114,3 ~ ±5 ALSI ½ ±5 60 ø114,3 ~ ±5 51

52 BAG FILTERS SIZE 1 & 2 Ultra-Bag PP / PE / NMO Polypropylene, Polyester or Nylon 1 to 1200 µm 80% 18cm Size 1: 45 cm, Size 2: 85 cm PP: 82 C. PE: 120 C. NMO: 90 C Features & Benefits Top ring of polypropylene, polymer or stainless steel. The filter bags distinguish themselves by high flow capability and dirt holding capacity. They come in a broad selection of filtration degrees from 1 to 200 micron in polypropylene and the high temperature polyester bags. We also carry Nylon bags for rough filtrations up to 1200 microns. Less than 30% particles can pass through a bag filter of the same filtration degree. All bags are available as FDA and EC certified version with polypropylene fixture, as well as with a steel ring fixture version for industrial applications. Polypropylene and polyester bags utilize the depth filtration technique, trapping various particles and oil remnants in the fibers of the material, however the nylon material is a mesh filter bag, meaning it s a surface filtration, often used for more viscous liquids or coarser filtration degrees. Bag material Polypropylene Polyester Nylon Ring material PP SS PM SS PM SS Food Beverages High viscosity Process Water - Over 80 C PP = Polypropylene. SS = Stainless Steel. PM = Polymer Size 1 Diameter: 18cm Length: 45 cm Flow: 380 l/min Size 2 Diameter: 18cm Length: 85 cm Flow: 680 l/min Filtration rate µm Material PP PE NMO 52

53 BAG FILTER HOUSING SIZE 1 & 2 BFOS Stainless steel 304 or l/min 10 bar (20 bar option) -10 to +80 C FPM (others available) The first filter of a production line is often the least clean, and has the highest flow. For this purpose, we recommend using a bag filter, as the high dirt holding capacity, as well as the high default flow rate makes it the optimal solution for many pre-filtrations, wastewater filtrations and also some cooling liquid lines. Bag filters come in 4 different sizes, from 100 liter/minute to roughly 680 liter/minute, and may be used for as fine filtrations as 1 micron. Our filter housings are constructed in stainless steel, most with a heavy bolt-lid. Our filter housings for bags have a specially fixed steel accessory to hold down the bag, using the fixture of the filter housings lid, to prevent any bypass past the filter bags. OPTIONS Bottom or side Outlet Model Flow l/min Double Version Connection in/out Bag size Duplex Version Dimensions (mm) Top Inlet Version A B C D E BFOS 1 BSP ø204 Max. 275 BFOS 1 DIN 380 DN ø204 Max. 275 BFOS 2 BSP ø204 Max. 275 BFOS 2 DIN 680 DN ø204 Max. 275 BFOS 2 DIN+ 680 DN ø204 Max. 275 BFOS Double 1300 DN80 / DN ø204 Max

54 DEPTH FILTER CARTRIDGES The Ultra-Depth filter cartridges are most often melt blown polypropylene or resin bonded filter elements, where the element is constructed porously with filtration pores of differing sizes, down to the innermost layer, which is no larger than the filtration degree of the depth filter cartridge. Depth filters are most commonly supplied with a double open end, for easy and fast installation and change-out. Less than 10% particles can pass a depth filter of the same filtration degree. DEPTH FILTER APPLICATIONS Whether it s the price or the availability, depth filters are amongst the most sold filtration products in the world, and application wise, this is for good reason. At Ultrafilter we carry 3 base-line depth filters, Ultra-Depth PP and RB, and Ultra-Wound. Depth filtration is a well-known and old filtration technique, high efficient for pre-filtration, clean-water filtration and a number of other applications, however depth filters have a certain efficiency like filter bags, and most depth filters reach much higher efficiencies than filter bags. Model Ultra-Depth PP Ultra-Depth RB Ultra-Wound Filtrationrates 1 µm to 75 µm 1 µm to 150 µm 1 µm to 150 µm Material Polypropylene Resin Cotton Maximum operating temperature 80 C 120 C 120 C Applications Chemicals Water Electronics Food & Beverages Industrial Pharmaceuticals 54

55 POLYPROPYLENE DEPTH FILTER Ultra-Depth PP-TF Polypropylene % 80 C 5 93/4 97/ / / DOE or Code 7 (others available) Ultra-Depth PP-TF is a high flow, graded depth filter with high contaminant capacity for long life. Constructed from FDA approved polypropylene with excellent performance characteristics, it is an economic choice for a wide range of applications. Ultra-Depth PP-TF is available in a range of industrial standard lengths as either absolute or nominal rated cartridges. Differential Pressure (mbar) Flow (l/min pr. 10 ) 1 µm 5 µm 10 µm 20 µm RECOMMENDED FILTER HOUSINGS FUC Single DS Multi DOE ME Multi Code 7 1N Plastic 55

56 RESIN DEPTH FILTER Ultra-Depth RB Resin % 120 C /4 191/2 291/4 39 DOE Features & Benefits High chemical resistance Ultra-Depth RB is an industrial filter, with a high temperature resistance, as well as a good chemical resistance to paints, inks, adhesives, coolants, pesticides, fertilizer, lube oils and many solvents. This filter is often used in energy production, as well as general industry, agricultural process liquids and general manufacture processes. Pressure Drop (mbar) Water Flow (l/min pr. 10 ) 3 µm 10 µm 50 µm 125 µm 5 µm 25 µm 75 µm RECOMMENDED FILTER HOUSINGS FUC Single DS Multi DOE FWK Multi DOE 1N Plastic 56

57 WOUND COTTON FILTERS Ultra-Wound Cotton media with SS304 core % 120 C (65 and 400 C optional) DOE Ultra-Spun series is perfectly suited as a pre-filter to protect more expensive secondary or final filtration systems. Cotton is mainly used where polypropylene is incompatible with the filtrate. The bleached cotton meet the FDA standards and is designed specifically for water and food applications. The core is made of stainless steel, and makes the filter useful in high temperature applications. Differential Pressure (mbar) Flow (l/min pr. 10 ) 1 µm 5 µm µm 100 µm RECOMMENDED FILTER HOUSINGS FUC Single DS Multi DOE FWK Multi DOE 1N Plastic 57

58 PLEATED FILTER CARTRIDGES The Ultra-Pleat filter cartridges is a surface filter with an efficiency of 99,9%. Often the final filters of industrial and even food and beverage productions, absolute filters use surface filtration with fixed pore sizes for very high efficiencies and low filtration degrees. On some filters, the media is applied in several layers for a specific effect on the filtration, however at a cost of differential pressure. Our absolute filters have a pleated media around the core for a larger filtration surface, securing a longer life for the filter and lower differential pressure. Absolute filters are most commonly supplied with a Code 7 connection, securing the elements by bayonet, securing a non-bypass connection between filter element and housing. As an alternative we also supply the Ultra-Pleat elements with DOE connections. Less than 0.1% particles can pass an absolute filter of the same filtration degree. Polypropylen Media Glass Fibre Media SERIES & APPLICATIONS The most used pre-filters for pharmaceutical and ingredient production plants, as well as a very common final filter for dairies, frozen food production and many beverage productions without a need a sterile grade filtration, we supply 3 different absolute filters of our own production, Ultra-Pleat GP-M, PP100 and PP-K. Model Ultra-Pleat GP-M Ultra-Pleat PP100 Ultra-Pleat PP-K Filtrationrates 0,5 µm to 5 µm 0,5 µm to 40 µm 0,5 µm to 40 µm Material Glass Fibre Polypropylene Polypropylene Maximum operating temperature 80 C 80 C 80 C Applications Chemicals Water Electronics Food & Beverages Industrial Pharmaceuticals Breweries 58

59 PLEATED FILTER GLASS FIBRE Ultra-Pleat GP-M Glass fibre 0,5 0, ,99% 80 C Code 7 or DOE (others available) EPDM (others available) A range of absolute rated cartridge filters from Ultrafilter, featuring the latest developments in borosilicate glass fibre filter media technology, GP-M Series cartridges are constructed from robust glass fibre and polypropylene filtration layers, offering removal ratings from 0.5 to 5 micron absolute. GP-M Series cartridges are suitable for absolute removal of unwanted particulates and for prefiltration to membrane filters. The GP-M Series cartridges incorporate a polypropylene prefiltration layer, combined with a high dirt capacity glass fibre media. This has the effect of longer service life, improved operating costs and smaller process footprint. Differential Pressure (mbar) ,5 µm RECOMMENDED FILTER HOUSINGS Flow (l/min pr. 10 ) 0,8 µm 1 µm 2 µm 5 µm FUC/FUCB Single PF-EG Sanitary ME Multi Code 7 DS Multi DOE 59

60 PLEATED FILTER POLYPROPYLENE Ultra-Pleat PP100 Ultra-Pleat PP100 cartridges are suitable for absolute removal of unwanted particulates and for prefiltration to membrane filters. Ultra-Pleat PP100 is our general purpose pleated filter cartridge. Suitable for most applications in food and beverage industry. The graded multi-layer polypropylene media provide prefiltration of the process fluid prior to the absolute rated final layer. The unique design of the PP100 cartridges helps to achieve lower running costs and a smaller process footprint. Polypropylene 0,5 0, ,99% 80 C Code 7 or DOE (others available) EPDM (others available) Differential Pressure (mbar) Differential Pressure (mbar) Flow (l/min pr. 10 ) 0,5 µm 0,8 µm Flow (l/min pr. 10 ) 1 µm 2 µm 3 µm 5 µm 7 µm RECOMMENDED FILTER HOUSINGS FUC/FUCB Single PF-EG Sanitary ME Multi Code 7 DS Multi DOE 60

61 PLEATED FILTER POLYPROPYLENE Ultra-Pleat PP-K Ultra-Pleat PP-K is specially suited for filtration of broad particle mix. The wider pleating of the filter media ensures that the filter will block. The combination of up to eight separate filtration layers provides true depth filtration, within a pleated cartridge construction, and resistance to fouling. The Ultra-Pleat PP-K are also highly resistant to integrity failure caused by steam sterilisation and have excellent chemical compatibility characteristics. Polypropylene 0, ,99% 80 C Code 7 or DOE (others available) EPDM (others available) Differential Pressure (mbar) Differential Pressure (mbar) Flow (l/min pr. 10 ) 3 µm 5 µm 10 µm 15 µm 20 µm Flow (l/min pr. 10 ) 0,5 µm 1 µm 2 µm RECOMMENDED FILTER HOUSINGS FUC/FUCB Single PF-EG Sanitary ME Multi Code 7 DS Multi DOE 61

62 MEMBRANE FILTER CARTRIDGES Ultra-Mem is our series of membrane filter cartridges with an effectivity of 99,999999%. Very often the final filtration step in high requirement productions will be one or more membrane filters. A high demand product in the pharmaceutical and veterinary industries, membranes are available in many lengths from 5 to 40 long, and they come in a number of materials and specifications to fit almost any filter housing and filtration task you might have. filtrations of corrosive or high turbidity media. Most membranes can be regenerated with an autoclave or CIP steam, and may be used several times, as long as the filter integrity remains uncompromised. Polypropylen Media Glass Fibre Media Polyethersulphone Media Nylon Media SERIES & APPLICATIONS The most demanding of all filtration tasks are completed through membranes. Almost always the final filtration step, membranes are used primarily in pharmaceutical, chemical and food and beverage industries, specifically for end-product or ingredient production at pharmaceutical or chemical production plants, and for very high quality filtered beer, wine and fine spirits, but are also used for the most demanding sterile water filtration. A number of membranes are available in a number of retention rates, to meet the needs of your specific production and liquid media. Filtrationrates 0,04-1,2 µm 0,1-0,2 µm 0,2-0,65 µm 0,2-0,45 µm 0,2-0,45 µm Material PES PP PES Nylon PES Maximum operating temperature Chemicals 60 C 80 C 60 C 60 C 60 C Applications Water Electronics Food & Beverages Industrial Pharmaceuticals 62

63 GENERAL PURPOSE MEMBRANE Ultra-Mem PF-PES Polyethersulphone 0,04 0,1 0,2 0,45 0,65 1,2 99,999999% 60 C Code 7 (others available) EPDM (others available) Ultra-Mem PF-PES is our standard membrane for critical liquid filtration. Careful media selection ensures that PF-PES cartridges are also very suited to critical particle control down to 0.04 micron ratings. PF- PES cartridges offer high flux rates and low differential pressures, a feature common to polyethersulphone membranes. PF-PES cartridges are validated for bacterial removal according to HIMA guidelines and ASTM F838-05, with a log reduction value >7. They are therefore suitable for applications requiring sterilising grade filtration Differential Pressure (mbar) Differential Pressure (mbar) Flow Rate (l/min pr. 10 ) 0,04 µm 0,1 µm Flow Rate (l/min pr. 10 ) 0,2 µm 0,45 µm 0,65 µm 1,2 µm RECOMMENDED FILTER HOUSINGS 63 FUCB Single PF-EG Tri-clamp Single / Multi PF-EG Dairy Single / Multi PF-EG Weld Single / Multi

64 MEMBRANE FOR CHEMICALS Ultra-Mem PF-PP Polypropylene 0,1 0,2 99,999999% 80 C Code 7 (others available) EPDM (others available) For solvent and aggressive chemical filtration applications, Ultra-Mem PF-PP cartridges offer a wide range of chemical compatibility. Suitable for the most demanding microfiltration applications, the cartridges can be used for the filtration of aggressive chemical solutions including acids, alkalis, solvents and etchants. PF-PP cartridges can also be used for a wide range of sterile venting and gas filtration applications. Differential Pressure (mbarg) Clean Water Flow Rate (l/min pr. 10 ) 0,1 µm 0,2 µm RECOMMENDED FILTER HOUSINGS 64 FUCB Single PF-EG Tri-clamp Single / Multi PF-EG Dairy Single / Multi PF-EG Weld Single / Multi

65 MEMBRANE FOR BEVERAGES Ultra-Mem PF-BEV Dual Polyethersulphone 0,2 0,45 0,65 99,999999% 60 C Code 7 (others available) EPDM (others available) Ultra-Mem PF-BEV is a membrane filter specially designed for filtration of beverages. The Ultra-Mem PF-BEV 0,45 micron rated filter removes yeastsand moulds including the smallest spoilage bacteriasuch as Oenococcus oeni. The PF-BEV 0,65 micronrated filter removes contaminating yeast, moulds,and spoilage bacteria from beverages. The PF- BEV 0,2 micron rated cartridges provide sterile filtrationfor bottled water and other beverage grade waterapplications. Ultra-Mem PF-BEV cartridges are validated for bacterialremoval according to HIMA guidelines and ASTMF838-05, with a log reduction value >7. They aretherefore suitable for applications requiring sterilisinggrade filtration. Differential Pressure (mbar) Flow (l/min pr. 10 ) 0,2 µm 0,45 µm 0,65 µm RECOMMENDED FILTER HOUSINGS 65 FUCB Single PF-EG Tri-clamp Single / Multi PF-EG Dairy Single / Multi PF-EG Weld Single / Multi

66 NYLON MEMBRANE FILTER Ultra-Mem PF-NYL Nylon 0,1 0,2 0,45 99,999999% 60 C Code 7 (others available) EPDM (others available) Ultra-Mem PF-NYL cartridges are manufactured from a multi-layer combination of irrigation mesh, filter membrane, membrane support and drainage material. PF-NYL cartridges have optimal pleat geometry to maximise the available filtration area and to ensure an efficient flow through the cartridges. Differential Pressure (mbar) Flow Rate (l/min pr. 10 ) 0,2 µm 0,45 µm RECOMMENDED FILTER HOUSINGS 66 FUCB Single PF-EG Tri-clamp Single / Multi PF-EG Dairy Single / Multi PF-EG Weld Single / Multi

67 MEMBRANE FOR WATER FILTRATION Ultra-Mem PF-AQUA Polyethersulphone 0,2 0,45 0,65 1,2 99,999999% 60 C Code 7 (others available) EPDM (others available) Ultra-Mem PF-AQUA is a membrane specially suited for filtration of water products such as bottled water. Careful media selection ensures that Ultra-Mem PF-AQUA cartridges are suited to retention down to 0,2 micron ratings. PF-AQUA cartridges offer high flow rates and low differential pressures, a feature common to polyethersulphone membranes. All components used in the construction of Ultra-Mem PF- AQUA cartridges are FDA approved to 21CFR and meet or exceed the latest EC Directives for Food Contact. Differential Pressure (mbar) Flow Rate (l/min pr. 10 ) 0,2 µm 0,45 µm 0,65 µm 1,2 µm RECOMMENDED FILTER HOUSINGS 67 FUCB Single PF-EG Tri-clamp Single / Multi PF-EG Dairy Single / Multi PF-EG Weld Single / Multi

68 SINGLE CARTRIDGE FILTER HOUSING FUC / FUCB Stainless steel 304 or l/min 25 bar 1 BSP 90 C DOE, Code 7 or Code 3 FPM (others available) Our filter housings are constructed in stainless steel, most with a heavy bolt-lid or solid clamp lock for the smaller housings. All housings are available in 316 and 304 stainless steel. Select sizes are available in heavy-duty plastic versions for off-shore and other applications. Our single element filter housings for DOE have a specially fixed steel accessory to secure the elements from shaking. This also allows several length configurations, using the fixture extend or shorten the element length. Model Flow l/min Connection in/out Max. Temperature Element Connection Dimensions (mm) A B C D E F G H FUC C DOE ø88, FUC C DOE ø88, FUC C DOE ø88, FUC C DOE ø88, FUCB C Code ø88, FUCB C Code ø88, FUCB C Code ø88, FUCB C Code ø88,

69 PLASTIC FILTER HOUSING 3M 1N Polypropylene or Polycarbonate l/min 10 bar R 3/4 or Rp 3/4 80 C 93/4 or 191/2 DOE Nitrile (others available) The model 1N plastic housing is manufactured from a high impact plastic for added strength and has been specifically designed to meet most industrial application requirements for liquid filtration. The model 1N is available with R ¾ or Rp ¾ inlet and outlet connections. The model 1N may be fixed with a mounting bracket (optional). Double sump length allows extended cartridge change-out and reduces maintenance costs. No tool is needed for the threaded sump connection. Model Flow l/min Connection in/out Max. Temperature Element Connection Dimensions 1N1 25 R 3/4 / Rp 3/4 80 C DOE N2 50 R 3/4 / Rp 3/4 80 C DOE A H 69

70 MULTI CARTRIDGE HOUSING DOE DS Stainless steel 316L Electropolished l/min 10 bar 100 C DOE 5 or 12 cartridges Nitrile The DS Series filter cartridge housings have a simple and robust construction and are fitted with a V-band clamp or swing bolt closure system for rapid opening and cartridge change-out. Standard housings are configured to accept double open end style (DOE) cartridges. These DS DOE housings use pressure plate assemblies including top cup and spring seal assemblies that permit the use of filter cartridges with single-length equivalents of 9 ¾ to 10 inches. To adapt the housing to accept single open end (SOE), double O-ring cartridges with locating spear, the standard pressure plate is replaced with the SOE pressure plate (to be ordered separately). The housing handles liquids at pressures up to 10 bar g and temperatures of up to 100 C. All wetted surfaces are in 316L stainless steel. Other parts (V-band clamp, feet mountings, etc.) are supplied in 304 stainless steel or similar. DS filter housings are electropolished for a consistent, easy care finish. Nitrile gaskets are supplied as standard. Other gasket materials are available as standard items and can be readily swapped with those supplied. The 5 cartridge round housings are available with either male-threaded BSPT or flanged (PN16) connections. The 12 round housings are fi tted with DIN PN16 DN80 flanges. All vents and drains are female BSP. Multi Cartridge Housings Flow l/min Connection Max. Temperature Element Connection 5 DS /2 or DN C DOE 5 DS or DN C DOE 5 DS or DN C DOE 5 DS or DN C DOE 12 DS DN C DOE 12 DS DN C DOE 12 DS DN C DOE 70

71 MULTI CARTRIDGE HOUSING CODE 7 ME Stainless steel 316L Electropolished l/min 10 bar 90 C DOE, Code 7 or Code 8 EPDM Because of its design the ME series is suitable for all the field of use where is necessary a filter housing of industrial design and for all the filtration process where cleaning and a easy to use filter hosuing is necessary. A typical use of ME filter housing series is for cleaning water treatment, rough filtration and filtration of spring water. Splitted bowl design assure an easy access to the cartridges Bowl design assure high resitance at bad falls Heavy duty Vee Band design allow a safety closure avoiding accidental opening Full range of accessories available in AISI 316L or PVC material Standard O-ring Adjustable legs allows the user to set IN/OUT heights Filter housing traceability Certificates available on request 2D/3D drawings available on request Model Flow l/min Connection in/out Filter Element BSP DIN Size Qty 03ME DN50 20 Code ME DN50 30 Code ME DN50 40 Code ME ,5 DN65 20 Code ME ,5 DN65 30 Code ME ,5 DN65 40 Code ME DN80 30 Code ME DN80 40 Code

72 MECHANICAL POLISHED FILTER PF-EG Stainless steel 304L or 316L 0,8 / 0, l/min 10 bar 150 C DOE, Code 7 or Code 8 EPDM CONNECTION TYPES Dairy Tri-clamp Welded Flange 72

73 MECHANICAL POLISHED FILTER PF-EG Sanitary filter housings are made with no surface impurities, no thread or nooks in the filter housings, that may be harder to get clean. We have sanitary filter housings as both single and multi element versions, and deliver these stainless steel filter housings in stainless steel 304L or 316L mechanical polished down to 0,8 or 0,4 Ra. Model Flow l/min Connection in/out Filter Element DIN Tri-clamp Weld Size Qty PF-EG DN25 DN25 N/A 5 Code 7 1 PF-EG DN ,4 x 1,65 10 Code 7 1 PF-EG DN ,4 x 1,65 20 Code 7 1 PF-EG DN ,4 x 1,65 30 Code 7 1 PF-EG DN ,4 x 1,65 40 Code 7 1 PF-EG DN40 1,5 38,1 x 1,65 20 Code 7 3 PF-EG DN40 1,5 38,1 x 1,65 30 Code 7 3 PF-EG DN ,8 x 1,65 20 Code 7 5 PF-EG DN40 1,5 38,1 x 1,65 40 Code 7 3 PF-EG DN ,8 x 1,65 30 Code 7 5 PF-EG DN ,8 x 1,65 20 Code 7 8 PF-EG DN ,8 x 1,65 40 Code 7 5 PF-EG DN ,8 x 1,65 30 Code 7 8 PF-EG DN ,8 x 1,65 40 Code 7 8 PF-EG DN65 2,5 63,5 x 1,65 30 Code 7 12 PF-EG DN65 2,5 63,5 x 1,65 40 Code 7 12 PF-EG DN65 2,5 63,5 x 1,65 30 Code 7 18 PF-EG DN65 2,5 63,5 x 1,65 40 Code 7 18 PF-EG DN ,2 x 1,65 30 Code 7 30 PF-EG DN65 2,5 63,5 x 1,65 40 Code 7 24 PF-EG DN ,2 x 1,65 40 Code

74 HIGH FLOW FILTER Stainless steel 304L or 316L l/min 10 bar C 3M High Flow EPDM The unique construction of High Flow Filters (patent pending) permits flow rates of up to 113 m³/hr (500 gpm) in a single cartridge. Resulting in fewer filter elements to accommodate your flow requirements. In fact, the High Flow Filtration System requires as few as one-tenth the number of elements as competitive 2.5 (63,5 mm) pleated cartridges. The High Flow housings are specifically designed to deliver all of the system s benefits in a compact footprint. Housings are available in standard designs, as well as customizable configurations to suit your specific needs. All standard High Flow housings are designed, manufactured, tested and code-stamped in accordance with ATEX Group II, Category 2, T5 and PED 97/23/EC rated Category I. Stainless steel housing external surfaces are glass-bead blasted for a consistent, easy care finish. The High Flow housing is available in a variety of sizes to accommodate from 1 to 7 filter elements in both 40 and 60 lengths. Larger housings are available upon request. Housings are also available in horizontal or vertical confi gurations, depending on your needs. Choose the horizontal option to help Model Nominal Diameter (mm) 1HF 220 3HF 450 5HF 500 7HF 600 Material 316L SS or 304L SS 316L SS or 304L SS 316L SS or 304L SS 316L SS or 304L SS Connection in/out (DIN) Recommended max. flow (m³/h) Max. Pressure and Vent & Drain Connections Temperature Vent Drain DN100 DN bar, 110 C 1/4 *** 1/2 *** DN150 DN ** bar, 110 C 1/2 1 DN200 DN ** 556** 10 bar, 110 C 1/2 1 DN250 DN bar, 110 C

75 HIGH CAPACITY FILTER CARTRDIGES 3M 740B Series Polypropylene l/min C Max. 3,4 bar (742B: 2,4 bar) FDA Buna N (others available) 16,5 cm 100 cm The 3M High Flow Filter Cartridge, 740B which incorporates a radial pleat, puts an extraordinary amount of surface area into a single cartridge. This results in the following: High loading capacity for long life and lower cost filtration Fewer cartridges for fewer change-outs, thus less labour cost Fewer seals, reduced risk of by-pass, thus high quality Extremely low disposal costs, less than a tenth of some cartridges Designed to fit in a range of vessels that holds from one to over 37 filters for a wide range of flow rates in competitively priced hardware. Double O-ring seals in a variety of material options means: Extremely low risk of by-pass for high quality fluids No loose parts to assemble for easy installation, thus less labour cost Also, no springs and caps to lose reduces the risk of by-pass Broad chemical compatibility for many applications Meltblown FDA compliant polypropylene microfibre filter media provides high particle removal efficiency for high quality filtration with broad chemical compatibility. Convenient handle for easy manual or mechanical removal. Model Particle removal Efficiency (µm) Differential pressure (mbar) 99% 95% 90% 75% 50% 4,54 m3/h 9,08 m3/h 13,6 m3/h 18,2 m3/h 742B 1 0,9 0,8 <0,7 <0,7 41,37 75,84 151,68 199,95 743B 2 1,1 0,9 0,7 <0,7 27,58 55,16 75,84 103,42 744B 5 2,5 1,7 1,5 1,1 13,79 27,58 34,47 48,26 745B ,5 1,5 6,89 20,68 27,58 41,37 746B ,0 6,89 13,79 20,68 27,58 747B ,5 6,89 13,79 20,68 27,58 748B ,52 11,03 17,24 22,75 749B ,14 8,96 13,79 18,61 75

76 MESH BASKET FILTER HIGH FLOW SF-IL Stainless steel m³/h 10 bar 50, 100, 150, 200, 250, 300, 500, C FPM (others on request) High flow filtration tasks doesn t always require specially pleated elements, and for some, the capacity of bag filters are not enough. This is where an in-line mesh filter housing SF-IL excels, as the sturdy 304 stainless steel filter housing, is supplied with a stainless steel mesh filter basket, that may be removed for cleaning and reuse. The filter housing is constructed with inlet and outlet opposite, to allow inline installation. From 66 liters per minute and a DN25 flange connection, all the way up to liters per minute and a DN200 flange. This filter takes care of a long range of filtration tasks, with large amounts of particles or a very high flow. The design of this filter housing allows easy access through the top lid, and to the mesh filter basket. The basket is designed to hold large amounts of dirt or particles, and may be cleaned for continuous use. This combination of a metal surface filter, with the dirt holding capacity of filter bags, allow for a longer use than most other high flow filters. The filter comes in a standard range of filtration degrees from 50µm to 1000µm, and the mesh filter has a double layer, to assure the efficiency of the filtration. 76 SF-IL Flow rate m³/h Connection in/out Filter area m² Dimensions (mm) A B C D E F SF DN25 ~0, Ø88, SF DN50 ~0, Ø88, SF DN65 ~0, Ø SF DN80 ~0, Ø SF DN100 ~0, Ø SF DN150 ~0, Ø SF DN200 ~0, Ø Differential pressure: 0,2 bar

77 STAINLESS STEEL MESH FILTER P-SM / P-SMp Stainless steel, cylindrical or pleated µm 99,99% 60 C DOE, Code 7, Code Y (UF) or Code 3 EPDM (others available) Ultrafilter offers a varied range of stainless steel mesh filters in the P-SM series. This product is produced in 316L stainless steel by default, for the best possible protection and efficiency of your application. Mesh filter elements have the great advantage they can be regenerated by ultrasonic bath or backwashing the system. After regeneration, the filter will be ready for use again. P-SM mesh filters are very robust filters, with a temperature tolerance up to 200ºC, and differential pressure tolerance of up to 5 bar(g), and with a start up differential pressure of max 0.15 bar (g). Stainless steel mesh filters are usable in food and beverage applications, and are additionally often used for particle retention in cosmetic, chemical, water treatment and syrup filtration. Many more applications apply. END CAPS DOE Code 7 UF / Code Y Code 3 FILTER HOUSING FOR P-SM As the P-SM is suitable for both air/gas and liquid, different filter housings are available for the element to suit different applications. Model FUCB PF-EG P-EG Applications Liquid Liquid Air & Gas Material 304 / / / 316 Maximum operating temperature 90 C 150 C 200 C 77

78 UV DISINFECTION Microorganisms in the water, whether bacteria, algae, parasites or many more, can cause trouble for operations and usage of the water, and the safest way to stop growth and migration of the organisms is UV treatment. Through UV systems, we can cover most tasks from water to turbid liquids, foodstuff, beverages or viscous liquids. We cover tasks from small supplies to very large systems, and all our systems are available in FDA approved stainless steel for general applications or polypropylene for corrosive environments. Stainless steel or Polypropylene m³/h 10 bar 80 C All our single- and multi lamp UV systems use the internationally acclaimed Ultratherm UV lamps. Our UV systems come with a number of options, including cabinet mounting for your convenience, a large touchscreen for easy interaction, or an automatic performance and event log. Other options include: UV sensor Fully automatic cleaning system Automatic lamp dimming (power save mode) Flow control /2 BSP 0,08 kw DN80 0,25 kw DN100 0,4 kw DN100 0,5 kw DN125 0,75 kw DN150 1,0 kw DN150 1,5 kw PP = Polypropylene. SS = Stainless Steel. 78

79

80 NITROGEN GENERATOR NS 10 or 12 bar -40 Features & Benefits High flow, low air to nitrogen ratio. Modular design. Expandable on location. Siemens PLC S7 Oxygen Analyzer (optional) Flow Control (optional) % and PPM versions. Ultrafilter offers very economical nitrogen (N2) generators and systems. Ultrafilter Nitrogen generators work by PSA principle (Pressure Swing Adsorption). High reliability, low operating costs and long service life, combined with good service, make our plants chosen by more and more customers. Our systems produce high quality nitrogen, with impurities being as low as 10 ppm or up to 3%, depending on customer needs. Model 10 ppm 50 ppm Nitrogen Production Flow (Nm³/h) 100 ppm 500 ppm 0,1% 0,5% 1% 2% 3% NS-7 2,2 2,9 3,5 4,8 5,7 8,3 10,0 12,2 13,1 NS-14 4,4 5,8 7,0 9,6 11,4 16,5 19,8 24,3 26,1 NS-21 6,6 8,7 10,5 14,4 17,0 24,6 29,6 36,3 39,0 NS-28 8,7 11,5 13,9 19,1 22,5 32,7 39,3 48,1 51,8 NS-37 10,9 14,4 17,3 23,8 28,1 40,7 48,9 59,9 64,5 NS-42 13,0 17,2 20,7 29,4 34,5 48,6 58,4 71,5 77,0 NS-49 15,1 20,1 24,3 33,0 38,9 56,4 67,8 83,1 89,4 NS-56 17,2 22,9 27,7 37,6 44,3 64,2 77,1 94,5 101,7 GENERATOR SETUP Compressor Generator Buffer Vessel Outlet Receiver (optional) Compressed air ISO Class (%): Class (ppm): Filters PE Dryer Filters SMF/AK 80

81 OXYGEN GENERATOR OS 10 or 12 bar -40 Features & Benefits High flow, low air to oxygen ratio. Modular design. Expandable on location. Siemens PLC S7 Oxygen Analyzer (optional) Flow Control (optional) The air around us is composed of nitrogen (78%) and Oxygen (21%) and small amounts of different gasses and elements. Therefore, it may be economically advantageous to recover oxygen itself for production or treatment. Ultrafilters Oxygen generator is a modular system that could easily be increased as necessary, in case of an expanded production. The purity of oxygen is continuously monitored by a highly precise analyzer, and you can choose between a purity of 90% or 95%. Model Oxygen Production Flow (Nm³/h) 90 vol. % 93 vol. % 95 vol. % OS-8 2,6 2,6 2,5 OS-16 5,3 5,2 5,1 OS-24 8,0 7,8 7,6 OS-32 10,6 10,3 10,1 OS-40 13,1 12,8 12,5 OS-48 15,6 15,1 14,9 When oxygen generator is certified as Class IIB medical devices directive 93/42/CE, it is also suitable for use in the health sector. GENERATOR SETUP Compressor Generator Buffer Vessel Outlet Receiver (optional) Compressed air ISO Class (%): Class (ppm): Filters PE Dryer Filters SMF/AK 81

82 TWIN TOWER NITROGEN GENERATOR NS-100 / NS-200 / NS-300 7,5 or 10 bar V / 50-60Hz Features & Benefits Feed air connection: 2 BSP Noise Level: Below 75 db(a) Power consumption: 0,3 kw Feed Air ISO 8573 Class: Flow control and oxygen analyzer (option) The NS generators extract the available nitrogen in the ambient air from the other gases by applying the Pressure Swing Adsorption (PSA) technology. During the PSA process compressed, cleaned ambient air is led to a molecular sieve bed, which allows the nitrogen to pass through as a product gas, but adsorbs other gases. The sieve releases the adsorbed gases to the atmosphere, when the outlet valve is closed and the bed pressure returns to ambient pressure. Afterward, the bed will be purged with nitrogen before fresh compressed air will enter for a new production cycle. In order to guarantee a constant product flow, the NS nitrogen generators use modules of two molecular sieve beds, which alternatively switch between the adsorption and the regeneration phase. Under normal operating conditions and with correct maintenance the molecular sieve beds will have an almost indefinite lifetime. Model NS-100 NS-200 NS-300 Nitrogen Production Flow (Nm³/h) Oxygen Content 5 % 3% 2% 1% 0,5% 0,1% 100 ppm 50 ppm 10 ppm Feed Air Pressure 7,5 10 7,5 10 7,5 10 7,5 10 7,5 10 7,5 10 7,5 10 7,5 10 7,5 10 Nitrogen Flow Nitrogen Pressure Feed air consumption Nitrogen Flow Nitrogen Pressure Feed air consumption Nitrogen Flow Nitrogen Pressure Feed air consumption ,0 7,3 5,5 7,6 5,8 7,8 6,0 8,0 6,0 8,0 6,3 8,3 6,3 8,3 6,3 8,3 6,3 8, ,0 7,3 5,5 7,6 5,8 7,8 6,0 8,0 6,0 8,0 6,3 8,3 6,3 8,3 6,3 8,3 6,3 8, ,0 7,3 5,5 7,6 5,8 7,8 6,0 8,0 6,0 8,0 6,3 8,3 6,3 8,3 6,3 8,3 6,3 8,

83 TWIN TOWER OXYGEN GENERATOR OS-80 / OS-100 7,5 bar V / 50-60Hz Features & Benefits Feed air connection: 2 BSP Noise Level: Below 75 db(a) Power consumption: 0,3 kw Feed Air ISO 8573 Class: Flow control and oxygen analyzer (option) The OS generators extract the available oxygen in the ambient air from the other gases by applying the Pressure Swing Adsorption (PSA) technology. During the PSA process compressed, cleaned ambient air is led to a molecular sieve bed, which allows the oxygen to pass through as a product gas, but adsorbs other gases. The sieve releases the adsorbed gases to the atmosphere, when the outlet valve is closed and the bed pressure returns to ambient pressure. Afterward, the bed will be purged with oxygen before fresh compressed air will enter for a new production cycle. In order to guarantee a constant product flow, the OS oxygen generators use modules of two molecular sieve beds, which alternatively switch between the adsorption and the regeneration phase. Under normal operating conditions and with correct maintenance the molecular sieve beds will have an almost indefinite lifetime. Model OS-80 OS-100 Nitrogen Production Flow (Nm³/h) Oxygen Content 95% 93% 90% Feed Air Pressure 7,5 7,5 7,5 Oxygen Flow Oxygen Pressure Feed air consumption Oxygen Flow Oxygen Pressure Feed air consumption

84 MINI NITROGEN GENERATOR N2-MINI Ambient: 5 C - 40 C 230V AC A Features & Benefits Duty Cycle: S1-100% Noise Level: Below 60 db(a)/1m N2-10 includes 6 liter N² holding tank Feed Air ISO 8573 Class: The N2 nitrogen generator is a high quality compact nitrogen generator for flow between 10 and 83 l/min. Wall or floor mount is possible. The small model N2-10 comes with an integrated long life, oil-free compressor. Model Nitrogen Capacity l/min Nitrogen Pressure bar g Nitrogen 20 C Feed Air Consumption l/min Feed Air Pressure bar g Weight kg Cabinet Dimensions mm N ,8% Built-in Compressor x 550 x 275 N ,5% x 550 x 275 N ,5% x 550 x 275 N ,5% x 800 x 275 N ,5% x 1600 x

85

86 ULTRA-PURE WATER FILTERS Pleat2 / UP110 / UP124 / UP1001 Polypropylene, Polyester & Nylon 25 l/min pr. 10 0, AC 90% 80 C 5 93/4 191/ mm DOE Usually a filter system for drinking water starts out with a 5 μm filter to ensure a good quality water. For issues with very small particles, such as ochre we add a 1 or 0,5 μm filter to the line after the 5µm prefilter. Sometimes the water has a bad smell or taste, such as from sulphur or chlorine, and this problem is removed by adding an activated carbon filter to the line. The filters coarser than 5µm are often used for garden ponds, outside water taps and other less demanding residential applications. Pleated Polyester 0,5 µm Meltblown Polypropylene 5-50 µm Sleeve Nylon µm Activated Carbon Application Drinking and bathing water 50 µm UP µm UP111 5 µm UP110 0,5 µm Pleat2 - Ochre - Bad taste / odour WC and washing machines Gardening water AK 86

87 ULTRA-PURE SLIM FILTER HOUSINGS A Polypropylene & SAN 28 l/min 8 bar 5-50 C B 3/4 5 93/4 191/2 DOE EPDM In Denmark the waterworks are traditionally very efficient at cleaning and filtering our tap water, to a degree that gives us some of the purest water in the world, but despite this, there may be loose particles in the water. The particles often come from old water pipes, private wells and sometimes from water pumps in tall buildings and the like. The Ultra-Pure water filtration series consists of high quality filter housings and elements at competitive prices. The AQ2 water filter housing in strong plastic with brass threads is available in three versions: SINGLE: Is a single filter that can be used for applications where there is only used a filtration step, such as filtering for sand or removing particles from garden water. DUPLEX: Is a two-step filter solution for removal of smaller particles like ochre. TRIPLEX: Consists of three filter housings and is mostly used when to resolve issues with both ochre and taste / smell. Model Flow l/min Connection in/out Element QTY Dimensions (mm) AQ2 Mini 15 3/4 1 x AQ2 Single 28 3/4 1 x 9 3/ AQ2 Duplex 28 3/4 2 x 9 3/ AQ2 Triplex 28 3/4 3 x 9 3/ A B 87

88 ULTRA-PURE JUMBO FILTER Polypropylene or Polyester 75 l/min pr. 10 0, AC 90% 80 C mm DOE Jumbo filter elements have a much larger diameter than the standard range of elements. This gives them a large capacity of 75 l/min pr. 10. The filter elements are available in pleated polyester, meltblown polypropylene, wound polypropylene and activated carbon. Standard water filtration is done with a 5 µm filter. If you need to remove metallic particles such as ochre, we recommed to use the pleated polyester 0,5 µm filter element. For issues with taste and odour, for example from chlorine, an activated carbon filter can be used to solve the problem. Be aware that the activated carbon is more effective the longer contact time it has. Meaning that the recommended flow rate is lower. Pleated Polyester 0,5 µm Meltblown Polypropylene 5-50 µm Wound Polypropylene µm Activated Carbon Drinking and bathing water - Ochre - Bad taste / odour WC and washing machines Gardening water 88

89 ULTRA-PURE JUMBO HOUSING A Polypropylene l/min 6,2 bar 5-50 C B DOE Buna-N Sometimes 28 l/min is not enough. The standard AQ2 filter is great for single households and smaller companies, but if you have a large family or more than one house on the water line from your private well, then you might find 28 l/min insufficient. For this reason, we have the Ultra-Pure Jumbo filter housing. Available in two sizes, the Jumbo housing can handle flows from 80 l/ min to 150 l/min. Model Flow l/min Connection in/out Element qty A Dimensions (mm) Jumbo x Jumbo 9 3/ Jumbo /2 1 x Jumbo B 89

90 SCALE FILTER FOR MACHINES 3M ScaleGard Pro 38 C Sanitary Quick Change 3/8 BSPT or 10mm Push-in At Ultrafilter we conduct a range of cartridges from 3M developed specifically for café and restaurant industry. These cartridges filter particles from the water before coffee machines, soft drinks machines and ice machines. The ScaleGard Pro range is a disposable scale control system designed to protect coffee and vending equipment from scale build up. Designed to prevent hard scale formation in the heating coils that results in energy inefficiency, downtime and expensive service calls. Most sizes are available in a bypass and non-bypass version. The bypass version lets 25% of pass around the filter so you keep some minerals in the water which can provide great taste. We recommend the bypass versions for applications where the water quality is good, but you want to improve the quality of your coffee. The no bypass version is recommended for applications where there are unwanted particles in the water. Model Capacity (liters) 25% Bypass Flow Rate (l/min) P115-E 600 1,9 Applications Coffee Vending Combi Ovens Steamers P124-BNE ,9 P145-E ,9 P145-BNE ,9 P165-E ,9 P165-BNE ,9 P195-E ,8 P195-BNE ,8 P1175-E ,8 P1175-BNE ,8 90

91

92 FINDING THE RIGHT SIZE DRYER The flows mentioned in the dryer tables are based on specific operating conditions. To calculate the right size dryer you should use the correction factors below. Refrigeration Dryers The formular below can be used to calculate the correct capacity of both the UD 50Hz and UD 60Hz. Flow x K1 x K2 x K3 x K4 Operating Pressure bar (g) Compressed Air Inlet Temperature Correction factor K1 0,71 0,82 0,90 0,96 1,00 1,04 1,07 1,09 1,11 1,13 1,15 1,16 1,18 1, Correction factor K2 1,23 1,00 0,81 0,66 0,57 0,52 0,48 0,44 0,40 Ambient Temperature Correction factor K3 1,05 1,00 0,95 0,89 0,84 0,78 0,72 Dewpoint Correction factor K4 1,00 1,24 1,38 1,40 High Pressure Refrigeration The formular below can be used to calculate the correct capacity of both the UD 50Hz and UD 60Hz. Flow x K1 x K2 x K3 x K4 Operating Pressure bar (g) Correction factor K1 0,94 0,97 0,99 1,00 1,01 1,01 Compressed Air Inlet Temperature Correction factor K2 1 0,77 0,46 Ambient Temperature Correction factor K3 1,05 1,00 0,90 0,90 0,84 0,79 0,73 Dewpoint Correction factor K4 1,00 1,12 1,25 1,41 92

93 FINDING THE RIGHT SIZE DRYER Membrane Dryer The formular below can be used to calculate the correct capacity of both the UD 50Hz and UD 60Hz. Flow x K1 Operating Pressure bar (g) Correction factor K1 0,41 0,56 0,76 1,0 1,22 1,48 1,76 1,86 2,22 HeatLess HL For calculating capacity on our HeatLess HL adsorption dryer, use the correction factor below. Flow x K1 Correction factor K1 Operating Pressure (bar g) ,63 0,75 0,88 1,00 1,13 1,25 1,38 1,50 1,55 1,60 1,65 1,70 1,76 Inlet 40 0,55 0,66 0,77 0,88 0,99 1,10 1,21 1,32 1,43 1,54 1,65 1,70 1,76 temp. ( C) 45 * 0,42 0,50 0,59 0,67 0,76 0,84 0,92 1,01 1,09 1,17 1,26 1,34 1,42 50 ** 0,35 0,41 0,48 0,55 0,62 0,69 0,76 0,83 0,90 0,96 1,03 1,10 1,17 * PDP -25 C **PDP -20 C VarioBlo The capacity of the VarioBlo heat regnerated adsorption dryer can be calculated with the formular below. Flow x K1 (x K2 - For PDP -70 C) Correction factor K1 Operating Pressure (bar g) ,71 0,86 1,00 1,15 1,18 1,25 1,37 Inlet 35 0,62 0,75 0,87 1 1,12 1,25 1,37 temp. ( C) 40 0,38 0,54 0,67 0,82 0,92 1,07 1, ,33* 0,45** 0,54** 0,61*** 0,72 0,80 * PDP -20 C **PDP -25 C ***PDP -30 C Correction factor K2 Inlet temp. ( C) Operating Pressure (bar g) ,90 0,90 0,80 0,80 0,80 0, ,80 0,80 0,80 0,80 0,80 0, ,70 0,70 93

94 WATER CONTENT IN AIR The table below shows the water content in compressed air at different temperatures. This is useful for calculating the capacity of dryers. Dew Point C g/nm³ ppm , , , , , , ,0027 2, , ,7-55 0, ,6-50 0, ,4-48 0, ,6-46 0, ,0-44 0, ,1-42 0, ,5-40 0, ,9-38 0, , ,8-34 0, , , , , , , , , , , , , , , , , , , , , , , , , , , Dew Point C g/nm³ ppm 0 4, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

95 COMPRESSOR CAPACITY You can use this table to find the compressor capacity and size the filtration accordingly. m³/h m³/min l/sek cfm kw HP 5 0,08 1,39 2,9 0,5 0,7 10 0,17 2,78 5,9 1,1 1,5 15 0,25 4,17 8,8 1,5 2,0 20 0,33 5,56 11,8 2,2 3,0 25 0,42 6,94 14,7 3,0 4,0 35 0,58 9,72 20,6 4,0 5,5 50 0,83 13,89 29,4 5,5 7,5 65 1,08 18,06 38,3 7, ,33 22,22 47,1 9, ,67 27,78 58,9 11, ,08 34,72 73,6 13, ,50 41,67 88,3 15, ,92 48,61 103,0 15, ,75 62,50 132,4 22, ,00 83,33 176,6 30, ,25 104,17 220,7 37, ,50 125,00 264,9 45, ,17 152,78 323,7 55, ,83 180,56 382,6 65, ,50 208,33 441,4 75, ,17 236,11 500,3 90, ,67 277,78 588,6 90, ,58 326,39 691,6 110, ,50 375,00 794,6 132, ,00 416,67 882,9 160, ,50 458,33 971,2 160, ,50 541, ,7 200, ,50 625, ,3 200, ,83 763, ,6 250, ,33 972, ,0 315, , , ,3 400,

96 COMPRESSED AIR FILTRATION 96

97 LIQUID FILTRATION 97

98 END CAP CONFIGURATIONS Our proces filter elements are available with a wide range of different end cap configurations. This ensures compatibility with nearly any filter housing and lets us replace elements from other brands. ULTRAFILTER STANDARD END CAPS Code Flat Code Fin ADITIONAL END CAPS Configuration name Top End Outlet End End Fitting Seal Quantity End Fitting Seal Quantity Code 2 Flat None Open with lugs O-ring Code 3 Flat None Open O-ring Code 7 Fin None Open with lugs O-ring Code 8 Fin None Open O-ring Code 9 Recess None Flat open O-ring Code 18 (retro fit) Flat None Open O-ring Code 28 (S) Fin None Open with 3 lugs O-ring Code Y (UF) Flat None Open O-ring BS832 2 N SOE Recess None Flat open O-ring G SOE Flat None Flat open O-ring BS118 2 G DOE 10 Flat open Flat gasket 1 Flat open Flat gasket 1 DOE 93/4 Flat open Flat gasket 1 Flat open Flat gasket 1 If you don t find your desired end cap configuration, contact Ultrafilter for availability. 98

99 SHOP ONLINE At you will find a wide selection of filtration products ready for you to order. ABOUT US Ultrafilter Scandinavia offers a wide selection of filtration products for compressed air, liquids and gas. We have stock in Denmark and from here we distribute all of our products to Scandinavia and the Baltic countries. Ultrafilter Scandinavia is a part of the Ultrafilter group. Our production facility is in Germany and we have several subsidiaries in Europe and the United States. You can buy our products on local websites. Information about our products as well as brochures and manuals can be found on our website ( We can adapt all of our filtration products to your needs, and we offer visits from our consultants in order to find the right solution for you. We also offer on going service on our products once they are installed. FILTRATION OF ULTRAFILTER SKANDINAVIEN APS Sunekær Søndersø Denmark info@ultra-filter.com