Safety guide. varioprint DP line

Transcription

1 Safety guide varioprint DP line

2 Copyright and Trademarks Copyright Copyright 2016 Océ. Illustrations and specifications do not necessarily apply to products and services offered in each local market. No part of this publication may be reproduced, copied, adapted or transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language in any form or by any means, electronic, mechanical, optical, chemical, manual, or otherwise, without the prior written permission of Océ. OCÉ MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THE CONTENTS OF THIS PUBLICATION, EITHER EXPRESS OR IMPLIED, EXCEPT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR NON-INFRINGEMENT. OCÉ SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THE CONTENTS OF THIS PUBLICATION. Océ reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes. Trademarks Océ, is a registered trademark of Océ-Technologies B.V. Océ is a Canon company. All other trademarks are the property of their respective owners. Edition US

3 Contents Contents Chapter 1 Safety information...5 Safety information (all countries)... 6 Chapter 2 Regulation notices Regulation notices...14 Chapter 3 General information General information Chapter 4 Miscellaneous...23 Online support for your product

4 Contents 4

5 Chapter 1 Safety information

6 Safety information (all countries) Safety information (all countries) Important Safety and Environment User Information Before using Your printing system, make sure that it is properly installed and that You have read and understand the User Documentation in order to operate the system safely and in accordance with its functional offerings. When using Your machine make sure to always comply with the User Documentation. Warning and caution indicators In order to warn and make aware all persons operating the machine of possible risks, dangers and/or hazards, safety warning labels have been applied where required. For safe operation it is important to understand the meaning of any label. Make sure you read and understand all label descriptions before you start operating the machine. In order to avoid potential hazards, make sure that preventive and remedial maintenance is executed by qualified and trained service technicians. Warning and caution indicators Before using Your printing system, make sure that it is properly installed and that You have read and understand the User Documentation in order to operate the system safely and in accordance with its functional offerings. When using Your machine make sure to always comply with the User Documentation. NOTE In some regions where this product is sold the following name(s) may be registered as a model number (). Canon varioprint DP line (Océ 01038) Depending on the context, the terms system, machine, and equipment used in the User Documentation mean the Océ printing system for which this User Documentation shall apply. Some consumables and materials designated to be used by this machine are accompanied with Safety Data Sheets. Please refer to the corresponding Safety Data Sheets for specific Safety and Environment Information and operating instructions. You may download the actual Safety Data Sheets from the support site of your product at " The machine bears the CE-mark to show conformance with applicable legal requirements. The relevant CE Declaration of Conformity is part of the User Documentation. You may also download it from the support site of your product at " Océ shall not be liable for damages from: Failure to comply with the User Documentation Work performed incorrectly on the machine Unauthorized modifications While every precaution has been taken in the preparation of this documentation Océ assumes no responsibility for errors or omissions contained herein. Océ reserves the right to revise this documentation and to make changes from time to time. Warning and caution indicators (manual) The following indicators are used in the manuals to categorize the level of the seriousness of hazard: 6 Chapter 1 - Safety information

7 Safety information (all countries) WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the machine safely, always pay attention to these warnings. CAUTION Indicates a caution concerning operations that may lead to injury to persons if not performed correctly. To use the machine safely, always pay attention to these cautions. IMPORTANT Indicates operational requirements and restrictions. Be sure to read these items carefully to operate the machine correctly, and avoid damage to the machine or property. NOTE Indicates a clarification of an operation or contains additional explanations for a procedure. Reading these notes is highly recommended. NOTICE: Indicates an operation that must not be performed. Read these items carefully, and make sure not to perform the described operations Warning and caution indicators (machine) The following indicators are used in the machine to warn the user of possible safety risks: WARNING Whenever this label is affixed to parts of the machine that are accessible to the user, a remark can be found in the user documentation, explaining the potential hazard for which the user is warned or cautioned. The user is urged to consult the user documentation in order to understand the safety risk and learn how to avoid damage or injury. CAUTION Ignoring this Caution Hot symbol could cause injury to skin; see also the Actions in response to troubles section. Persons Ordinary person This safety manual describes safeguards for the protection of an ordinary person. Ordinary person is the term applied to all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the equipment, but also all persons who may have access to the equipment or who may be in the vicinity of the equipment. Chapter 1 - Safety information 7

8 Safety information (all countries) Disassemble and modification WARNING Do not remove covers and panels which are fixed to the machine. Some machines have a high-voltage component or a laser beam source inside that could cause an electrical shock or blindness. Do not modify this machine, because this could cause a fire, electrical shock or breakdown. If the machine contains a laser, the laser beam source could cause blindness. Do not carry out maintenance activities for other components and maintenance materials than the components and materials that are mentioned in the user manual. To avoid any risk, only properly qualified and trained service technicians are allowed to modify the machine. Do not bridge or disable any safety interlock devices. IMPORTANT Do not open any door while the machine starts up or runs, unless the operator panel displays a message that asks you to open one or more doors. Do not bridge any mechanical or electrical circuit breakers. Power cord WARNING Do not scratch, abrade, heat, twist, bend, place a heavy object on or cause any other damage to the power cord. The use of a damaged power cord (exposed core wire, broken wire, for example) could result in a fire or breakdown. If you find any of these conditions, immediately turn OFF the power switch and unplug the power cord from the power outlet. Then call your authorized service representative. Do not use an extension lead to connect the machine. Do not use any power cable other than the one provided. Never use the power cable with any other electrical device. Only use a power cord that is fitted with a protective earth conductor. Power source WARNING Put the power plug directly into a wall socket that has the same configuration as the plug. The use of an adapter leads can result in an inadequate power supply. If a proper wall outlet is not available, ask a qualified electrician to carry out the installation. Do not use a multiple outlet adapter or an extension lead. Contact your authorized service representative if an extension lead is required. The use of an extension cord may result in fire or electrical shock. IMPORTANT Consult your authorized service representative before you connect other equipment to the same wall outlet. Do not connect the machine to a mains voltage that differs from the value as stated on the power marking label. 8 Chapter 1 - Safety information

9 Safety information (all countries) NOTE If connection to a different mains voltage is required, contact your authorized service representative. Power plug WARNING For machines that are connected via a wall socket: Place the machine close to a wall socket that is easily accessible. The power plug is intended to serve as a disconnect device. Grounding WARNING Connect the power cord to an electrical outlet (wall socket) that is equipped with a grounding terminal. This equipment has not been designed for connection to an IT power system. An IT power system is a voltage network in which the neutral wire is not connected to ground. Installation WARNING We recommend that you only connect copy-control products (or other products) that meet (inter)national product safety and radio frequency interference standards. Only use an attachment cable as specified by the manufacturer. Make sure that the machine is placed on a level, horizontal surface of sufficient strength. Do not place this machine on an unstable or tilted surface. Do not place this machine in a location that is subject to lots of vibrations and shocks. Do not use flammable sprays, liquids or gases near this product, because this could cause a fire. Ventilation WARNING The machine can produce odors of exhaust air when you: 1. Use this machine in a poorly ventilated room for a long time. 2. Produce large amounts of copies or prints. Therefore, make sure that you ventilate this room well. Do not place the machine in rooms which are too small and insufficiently ventilated. See the Product Safety Data Sheet of the machine for the ventilation requirements. IMPORTANT Do not block the ventilation openings of the machine. Be sure to allow a clearance of 100mm or more at the back of this machine for the ventilation duct. Chapter 1 - Safety information 9

10 Safety information (all countries) Actions in response to troubles WARNING When a piece of metal, water or any other similar foreign matter gets inside the machine, immediately turn OFF the power switch and unplug the power cord from the power outlet. Then call your authorized service representative. Immediately stop using the machine if the machine becomes excessively hot, emits smoke, or produces unusual odors or noises. Immediately turn OFF the power switch and unplug the power cord from the power outlet. Then call your authorized service representative. Stop using the machine if the machine was dropped or a cover was damaged. Immediately turn OFF the power switch and unplug the power cord from the power outlet. Then call your authorized service representative. CAUTION Some areas inside the machine become hot. Do not touch the locations which are labeled with the CAUTION HOT symbol. Touching these areas could cause burns. LCD display. Do not rub, press or touch the display surface with hard material, because the polarizer at the surface can be easily scratched. The LCD module consists of glass. Therefore, the LCD module can damage when you drop, pinch strongly or punch the module. When glass breaks, be careful that you do not get injured by glass pieces. Call Customer Service. Consumables, supplies and maintenance materials WARNING Do not throw contaminated parts or parts containing toner or ink into an open flame. Do not leave toner or ink containing or contaminated parts within reach of children. Keep maintenance materials away from children. CAUTION Always use the materials which the manufacturer recommended and which are developed for this machine. Materials not approved by the manufacturer may result in faults in your machine. Use maintenance materials or other materials for their intended purpose only. Do not dispose additive residues, their mixture with water, and empty additive containers with domestic waste but observe the manufacturer's stipulation. IMPORTANT Do not place any liquids on the machine. 10 Chapter 1 - Safety information

11 Safety information (all countries) Moving the machine WARNING Make sure that you disconnect the power cord and other cables before you move the machine. Make sure that you check the documentation for the correct machine location before you move the machine. Make sure that whenever the machine is moved, this is done by properly qualified people who have received adequate instructions. General use WARNING Do not lean, lie or stand on any part of the machine, including any unit that can be pulled outward (e.g. paper drawers). To prevent overbalance of the machine, only one drawer should be opened at the same time. Do not touch or ingest fluids from a broken LCD; Liquid Crystal Display. When clothes or skin come into contact with the fluid, immediately clean the clothes and skin with soap or alcohol. After eye contact, immediately wash the eyes with a washing lotion for at least 15 minutes and consult a physician. IMPORTANT Unplug the product when you will not use it for a long period of time. Chapter 1 - Safety information 11

12 Safety information (all countries) 12 Chapter 1 - Safety information

13 Chapter 2 Regulation notices

14 Regulation notices Regulation notices Grounding (Finland; FI, Norway; NO, Sweden; SE and Denmark; DK) FI: Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan. NO: Apparatet må tilkoples jordet stikkontact. SE: Apparaten skall anslutas till jordat uttag. DK: Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. Translation: The machine must be connected to a grounded power outlet. Radio Interference suppression (all countries except USA) Warning: This equipment is compliant with Class A. In residential environments this equipment may cause radio interference. Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. Warning: Operation of this equipment in a residential environment could cause radio interference. FCC approval (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Operator's Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If you make such changes or modifications, you could be required to stop operation of the equipment. ICES-003; Interference-causing equipment (Canada) CAN ICES-3 (A)/NMB-3(A) VCCI (Japan) Class A ITE 14 Chapter 2 - Regulation notices

15 Regulation notices Translation: This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur. In such cases, the user may be required to take corrective action. EAC (Russia, Kazakhstan and Belarus) The following information about this product can be found on the rear side of the machine: Model number Mains specifications Manufacturer Country of origin Production date <YYYY-MM-DD> EAC Marking Laser Safety (all countries) Laser safety This is a digital machine which operates using a laser. There is no possibility of danger from the laser provided the machine is operated according to the instructions in this manual. Since radiation emitted by the laser is completely confined within the protective housing, the laser beam cannot escape from the machine during any phase of user operation. This machine is certified as a Class 1 laser product according to IEC : This means the machine does not produce hazardous laser radiation. CDRH regulations This machine is certified as a Class 1 Laser product under Radiation Performance Standard according to the Food, Drug and Cosmetic Act of Compliance is mandatory for Laser products marketed in the United States and is reported to the Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration of the U.S. Department of Health and Human Services (DHHS). This means that the device does not produce hazardous laser radiation. The related label indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. CAUTION Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 0.39mW. Battery labeling (EEA and Switzerland) This product contains a battery. Please do not remove the battery. If the battery needs replacement, this should be done only by skilled service technicians who are aware of the removal instructions provided by Canon. This product contains (a) Button Cell(s). It (They) is (are) located in (a) printed circuit board(s) that is (are) essential for the continuous error-free functioning of the product. The button cell(s) Chapter 2 - Regulation notices 15

16 Regulation notices should be removed only by skilled service technicians who are aware of the removal instructions provided by Canon. Button cell location Button Cell Capacity [Ah] Contains the following substances (if applicable) Controller 0.2 Ah Lithium CAUTION Canon does not accept any liability for any damage or consequences, if the batteries are removed by persons other than Canon service personnel. Battery labeling (Taiwan) Translation: Waste Batteries, Please Recycle End of Life; WEEE (EEA and Switzerland) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be handed over to a designated collection point, e.g. on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service. For more information regarding return and recycling of WEEE products, please visit " Reference: Directive 2012/19/EU. 16 Chapter 2 - Regulation notices

17 Regulation notices End of Life; WEEE (India) This product is not to be disposed of with your household waste, according to the E-Waste (Management) Rules, This product should be handed over to a designated collection point, e.g. to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information regarding return and recycling of WEEE products, please visit " or write to us at customer.delight@canon.co.in. Also, this product complies with the "E-Waste (Management) Rules, 2016" and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 % by weight and 0.01 % by weight for Cadmium, except for the exemptions set in Schedule II of the Rule. RoHS (China) The Environmental Protection Use Period (EPUP) applicable for the printing system designated for deliveries to the Peoples Republic of China is 20years. This EPUP, which does not include consumables or expendables, does not affect any warranty that is provided for the system and may not be construed or interpreted as a separate guarantee for the printing system. 20 RoHS (Vietnam) Canon and Océ brand products sold in Vietnam market comply with following Circular and Decision -"Circular No.30/1011/TT-BCT dated August 10,2011 of the Ministry of Industry and Trade stipulating temporarily the permissible content limitation of some toxic chemicals in the electronic, electrical products" -Decision No.4693/QD-BCT correcting Circular 30/2011/TT-BCT Chapter 2 - Regulation notices 17

18 Regulation notices For the statement on Canon Marketing Vietnam website, please see the last paragraph on the web page of the following URL: " ENERGY STAR (all countries) Canon has joined the ENERGY STAR Program of the United States Environmental Protection Agency (EPA). The purpose of the ENERGY STAR program is to promote the manufacturing and marketing of energy-efficient equipment, thereby potentially reducing combustion-related pollution. Using the energy management features outlined below prevents unnecessary power consumption, which helps to prevent air pollution from electricity generating plants and saves money on your utility bills. As an ENERGY STAR Partner, Canon has determined that the varioprint DP line meets the ENERGY STAR criteria for energy efficiency laid down in the ENERGY STAR Program Requirements for Imaging Equipment (Version 2.0). Energy consumption (all countries) The energy consumption of Imaging Equipment can be determined using the TEC procedure. This procedure was developed under the supervision of the United States Environmental Protection Agency. TEC stands for Typical Electricity Consumption. The TEC value of a product represents the energy consumed in a week under standardized conditions. For the varioprint DP line the TEC-value is listed in the Product Safety Data Sheet. In order to limit energy consumption during times of non-use the varioprint DP line has a Sleep mode during which the power level is reduced. The value for the Sleep mode is listed in the Product Safety Data Sheet. Power Modes and Delay Times The energy consumption and efficiency are influenced both by the product technology and by the settings chosen by the user, especially the delay times that are selected to enter reduced power states. The following delay times have been pre-set. Operational mode Low Power Sleep Default Delay Time [minutes] 20 minutes (range 5-30 minutes) 40 minutes (range minutes) The modes above are automatically entered after the Default Delay Time has elapsed; counting from the moment the last print has been produced. These settings are recommended and for most users ensure both ease of use and low energy consumption. Between brackets are the minimum and maximum values. The Delay Times can be changed. Shorter delay times will reduce energy consumption even further, but may cause longer recovery times. In some cases longer delay times may prove to be more convenient, but it should be noted that this may cause an increase in energy consumption. Therefore, from an energy preservation point-ofview, longer delay times are not recommended. Automatic duplex Using both sides of paper reduces paper costs, energy consumption and the amount of paper in the waste disposal process. Therefore, the varioprint DP line is default set for automatic duplex copying and printing. 18 Chapter 2 - Regulation notices

19 Regulation notices Standby Power (Federal Energy Management Program) (all countries) This product meets the following criteria for the United States Federal Energy Management Program (FEMP): In Standby this product consumes < 1 W. After shutting down all systems properly, the Standby-mode as defined by FEMP is reached by switching the Main Switch to "0". This product has a hard-off switch. This product meets the ENERGY STAR Guidelines for energy efficiency. Electronic Product Environmental Assessment Tool (EPEAT) (all countries) This machine is not designed to prevent the use of toner manufactured by other companies than Canon. Product performance related to use of toner is the responsibility of toner brand owner. Recycled paper (all countries) The use of recycled paper benefits the environment. The varioprint DP line is designed to use recycled paper, including chlorine free paper, which complies with the requirements of EN12281:2002. Lamps (all countries) This product may contain lamps that are only intended for use in combination with and for this specific product (and related equipment) and such lamps are not intended for use in other applications. End of Life; Handling of disposal of parts (Japan only) 廃棄物の取り扱いについて使用済みの消耗品と消耗部品は 法令 条例に従って 産業廃棄物としてお客様が処理処分をお願い致します Translation: Handling of disposals Used consumables and expendables must be discarded by the customer as industrial waste in accordance with the laws as well the regulations of local government. Chapter 2 - Regulation notices 19

20 Regulation notices 20 Chapter 2 - Regulation notices

21 Chapter 3 General information

22 General information General information Caution labels and notations (all countries) The power-marking label is located near the mains entrance. If connection to a different mains voltage is required, contact Customer Service. Do not remove caution labels or caution notations. If a label or notation is soiled, please clean the label or notation. If you cannot make label or notation legible, or if the label or notation is damaged, please contact your service representative. Space requirements and operation precautions (all countries) The required operating space of this product will be communicated to each customer by the local sales representative during the Site Survey. Please refer to the corresponding Safety Data Sheets for specific safety information, including the dimensions of the product, the recommended room volume and ventilation rate. You can download the Safety Data Sheets from the support site of your product at " downloads.oce.com". Operating environment (all countries) The environmental requirements for correct operation of the machine are as follows: Operating temperature (T): 17 C (62.6 F) C (90.5 F) Relative Humidity (RH): 20% - 80% Operating altitude: below 2000m Deployment area: below 2000 m (approx ft) altitude and non tropical (China): Translation: Can only be safely used at altitudes below 2000 meters (approx feet). Translation: Can only be safely used in non tropical weather. Noise (all countries) Sound pressure (LpA = 66 db(a)): is used to characterize the sound level that will be experienced at operator position (in front of the product at a distance of 25 cm and a height of 150 cm) and is defined as the dynamic variation of the static pressure of air measured in force per unit area. Sound pressure is normally represented in decibels [db]. Typical values are a sound pressure level of 0 db, which is the average threshold of human hearing, and 60 to 70 db for normal conversation, 110 db at an extremely loud music concert, and 150 db for the noise of a jet engine at close range. 22 Chapter 3 - General information

23 Chapter 4 Miscellaneous

24 Online support for your product Online support for your product Downloads: User guides, printer drivers and other resources can change without prior notice. To stay up-todate, you are advised to download the latest resources from: " Before you use your product, you must always download the latest safety information for your product: make sure that you read and understand all safety information in the manual entitled 'Safety Guide'. Support For support information please contact your Canon local representative. Find your local contact for support from: " 24 Chapter 4 - Miscellaneous

25

26 CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo , Japan CANON U.S.A., INC. One Canon Park, Melville, NY 11747, U.S.A. CANON CANADA INC Mississauga Road Brampton, ON L6Y 5Z7, Canada CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands CANON AUSTRALIA PTY. LTD Building A, The Park Estate, 5 Talavera Road, Macquarie Park, NSW 2113, Australia CANON CHINA CO., LTD 2F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing , China CANON SINGAPORE PTE. LTD 1 Fusionopolis Place, #15-10, Galaxis, Singapore CANON INC. 2016