BeveLED Mini Trimless Acoustical - B3RDP

Transcription

1 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles Introducing Trimless Acoustical For the first time a sheetrock-looking solution for acoustical ceiling tiles. Perfectly centered fixtures, perfectly cut tiles Everytime. F E AT U R E S The clean, minimal trimless appearance of sheetrock in acoustical tiles. No cutting. No mess. No mistakes. And less labor. Proprietary tool-less mounting system. Trimless tile housings perfectly self-center in pre-cut tiles. NEC grid mount. No independent tie-in to structure required. Seismically rated. Trimless for acoustical ceiling tiles usailighting.com/trimlessacoustical D OW N L I G H T P E R FO R M A N C E DATA Shown with Beve Mini FT housing COLOR CHOICES Warm Glow Dimming Classic White Color Select D E L I V E R E D* PERFOR M ANCE: 9W 15W 20W 15W 20W 12W 18W Source Lumens: Lumens Per Watt: Delivered Lumens: *Based on 3000K, CRI. Performance varies for each specific beamspread and color temperature. See IES files for exact values at usailighting.com. C O R R E L AT E D C O L O R T E M P E R AT U R E M U LT I P L I E R Classic White - 9W and 15W 2700K 3000K Classic White - 20W 3500K 4000K 2700K 3000K 3500K 4000K Color Rendering Index: Multiplier for Lumen Color Select Warm Glow Dimming 2700K 3000K 3500K 2200K 2700K 3000K 3500K 4000K 5000K 6000K Color Rendering Index: Multiplier for Lumen Page 1 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

2 H OW T O S P E C I F Y Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles Specify fixture part number and options B3RDP Beve Trim Style Wattage Options Color Options Lens Beam Options Options Trim Finish Options Housing Options Voltage Options GW Armstrong Global White FT Flat Housing New Construction (3, 4, 6) UNV V Dimming Driver Options Accessories For use with Universal Voltage 120V - 277V CA2 Locking extendable channel bars for use with Armstrong pre-cut (provided standard) tiles from 24 to 30 wide Select one B3RDP Trimless Acoustical Classic White Light 09X1 9W 27KS 2700K, CRI 15X1 15W 27KH 2700K, CRI 20X3 20W 27KU 2700K, 95+ CRI (1) 30KS 3000K, CRI 30 30º beam (2) 40 40º beam (1) 45 45º beam (2) S Solite (provided standard) SF Solite Frosted BF Borosilicate Frosted ZW Armstrong Blizzard White AC Anodized Clear Matte SC Conduit Silver 30KH 3000K, CRI 55 55º beam (1) GR Grey 30KU 3000K, 95+ CRI (1) 65 65º beam BL Black No Additional Charge D2 TR 0-10V dim, 10% (5) NC1 New Construction All-in-One D6E Eldo 0-10V, 1% (7) NCCP Chicago Plenum (6) D4E 5 ECO, 5% (3, 4, 5, 7) D6B Eldo 0-10V, 0.1% (7) D7 Eldo DALI, 0.1% (7) 35KU 3500K, 95+ CRI (1) D18 Moons DMX, 0.1% (3, 4, 5, 7) 40KS 4000K, CRI 120V D19 Phase 2-wire, 1% (3, 4) 40KU 4000K, 95+ CRI (1) D3 2-wire, 1% (7) 347V Warm Glow Dimming 20WG2 20W (7) 2722KS 2700K-2200K, CRI 45 45º beam 2722KH 2700K-2200K, CRI 55 55º beam 3022KS 3000K-2200K, CRI 65 65º beam 3022KH 3000K-2200K, CRI Color Select Tunable White 18CS1 18W 6022KS 6000K-2200K, Tunable White Light CRI For use with 347V only D V dim, 1% 347V only (3, 4, 5, 6, 7) Notes: 1 Not available with X1 2 Not available with X3 3 Not available with Warm Glow 4 Not available with Color Select 3522KS 3500K-2200K, CRI 12CS1 12W For use with 120V only No Additional Charge 40KH 4000K, CRI 15WG2 15W EMW Emergency Battery Wet Location (8) D6A Eldo 0-10V, 0.1% (7) RAL Custom Color Specify RAL # 35KH 3500K, CRI EM Emergency Battery (8) D4H H ECO, 1% Fade (3, 4, 5, 7) BZ Bronze 35KS 3500K, CRI CA4 Locking extendable channel bars for use with Armstrong pre-cut tiles 48 wide D6F Eldo 0-10V, 1% (7) 5 Not available with 9W 6 Not available with EM 7 Not available with FT housing 8 Not available with 347V. NC1 housing only. Requires above ceiling access for service C O M P L E T E P R O D U C T FA M I LY 45 45º beam 55 55º beam 65 65º beam Adjustable - B3RAP Wall Wash - B3RWP Page 2 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

3 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles B E L OW C E I L I N G A P P E A R A N C E A N D T R I M D I M E N S I O N S In 24 X 24 Ceiling Tile P R E - C U T AC O U S T I C A L T I L E S F O R B E V E L E D M I N I R O U N D ORDER FROM AR MSTRONG CEILING SOLUTIONS 24 TILE SIZE 24 X Ø Nominal ARMSTRONG TILE STYLE PRE-CUT TILE PART NUMBER Calla 8935C35 Ultima 8936C35 Ultima High NRC 8938C35 Lyra PB 8941C35 Optima PB 8944C35 Compatible Grid Styles: Silhouette Suprafine Interlude Sonata Pre-cut Trimless Acoustical panel provided by Armstrong Contact Armstrong for custom colors and RAL s In 30 X 30 Ceiling Tile P R E - C U T AC O U S T I C A L T I L E S F O R B E V E L E D M I N I R O U N D ORDER FROM AR MSTRONG CEILING SOLUTIONS 30 TILE SIZE 30 X Ø Nominal ARMSTRONG TILE STYLE PRE-CUT TILE PART NUMBER Ultima 8937C35 Ultima High NRC 8939C35 Lyra PB 8942C35 Optima PB 8946C35 Compatible Grid Styles: Silhouette Suprafine Interlude Sonata Pre-cut Trimless Acoustical panel provided by Armstrong Contact Armstrong for custom colors and RAL s In 48 X 48 Ceiling Tile P R E - C U T AC O U S T I C A L T I L E S F O R B E V E L E D M I N I R O U N D ORDER FROM AR MSTRONG CEILING SOLUTIONS 48 TILE SIZE 48 X 48 ARMSTRONG TILE STYLE PRE-CUT TILE PART NUMBER Lyra PB 8943C35 Optima PB 8949C35 Compatible Grid Styles: Silhouette Suprafine Interlude Sonata 48 3 Ø Nominal Pre-cut Trimless Acoustical panel provided by Armstrong Contact Armstrong for custom colors and RAL s Contact Armstrong Ceiling Solutions for other tile sizes and shapes. Page 3 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

4 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles S H A L L OW P R O FI L E H O U S I N G S FO R : N E W C O N S T RU C T I O N - F T 24 X 24 Tile / /8 125/8 43/ /8 33/8 30 X 30 Tile / / /8 8 15/8 33/8 73/16 48 X 48 Tile / /8 125/8 8 15/8 33/8 163/16 Page 4 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

5 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles U N I V E R SA L A L L- I N - O N E H O US I N GS FO R : N E W C O N S T RU C T I O N - N C1 C H I C AG O P L E N U M R AT E D - N C C P 24 X 24 Tile /8 51/8 11/2 163/4 111/ /4 51/ /8 30 X 30 Tile /8 51/8 11/ /4 163/4 111/8 51/4 7 43/8 48 X 48 Tile /8 51/8 11/ /4 163/4 111/8 51/ /8 Page 5 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

6 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles S P E C I FI C AT I O N S F I E L D R E P L AC E A B L E L E D L I G H T E N G I N E is serviceable through the aperture without tools or with a Philips screwdriver. All light engines feature industry-leading color consistency. FI E L D R E P L AC E A B L E D R I V E R Unless otherwise specified, a 0-10V, 100%-10% solid state electronic constant current integral D2 dimming driver with a high power factor is provided standard and sources 2mA. All integral dimming drivers are located within the fixture housing and are serviceable from below the ceiling through the aperture. Some ontime delay may be experienced depending on control system used. All dimming drivers comply with IEEE C62.41 surge protection. E M E R G E N C Y BAT T E RY IOTA emergency battery provides backup power for 90 minutes. NC1 fixtures are provided with an integral emergency battery that requires above ceiling access for service, and a remote test switch, which comes with a 24 lead length for location of the test switch. Remote EM test switch is dry/damp only; select EMW emergency option for a wet location-rated EM test switch. Fixtures that have no EM option may be connected to an inverter (by others) for emergency lighting. Battery is not available with 347V. Remote Emergency Test Switch included. Above ceiling access required for service. HOUSING Housings are fabricated of 20 ga. steel construction with thru wire J-box, 4 in 4 out at min. 90 C, #12 AWG thru branch circuit wiring. Housing is provided with locking extendable channel bar accessory appropriately sized for tile size (must be specified when ordering). MOUNTING B3RDP fixtures are specifically designed for use with pre-cut ceiling panels by Armstrong Ceiling Solutions. fixture housing with integral spring clips snaps directly to Armstrong s tee-grid ceiling suspension system. Specify CA2 locking extendable channel bars for installation with ceiling panels, or CA4 locking extendable channel bars for installation with 48 ceiling panels. No cutting or field modifications are required. Seismically rated. Consult local codes for independent tie-ins. FI X T U R E W E I G H T FT housing weighs 4 lbs. NC1 and NCCP housings weigh 11 lbs. NC1 with EM weighs 14 lbs. WA R R A N T Y Based on IESNA LM , Beve has a 50,000 hour rated life at 70% lumen maintenance (L70). Warranty covers replacement parts for 5 years from date of shipment. Ambient temperatures at fixture location should not exceed 40 C during normal operation. For further information please refer to our website. C E I L I N G T I L E P R E - C U T O P E N I N G ( T I L E P R OV I D E D BY A R M S T RO N G) Acoustical Tile for B3RDP Trimless light - nominal 3.5 opening; specifically designed to fit B3RDP fixture. For full ceiling tile selection go to L I S T I N GS Dry/Damp/Wet location. UL2043 rated for use in air handling plenums. EM fixture is dry/damp only, specify EMW for wet listed remote test switch. NRTL/CSA-US tested to UL standards. IBEW union made. NOTES For use only with pre-cut ceiling panels by Armstrong Ceiling Solutions. Not for use in corrosive environment Use of pressure washer voids warranty PHOTOMETRICS Consult factory or website for IES files. Tested in accordance with IESNA LM79. Page 6 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

7 Beve Mini Trimless Acoustical - B3RDP 3 Round Downlight For Use With 3.5 Pre-cut Ceiling Tiles COLOR OPTIONS Classic White Light Our proprietary light engines achieve a 2-step MacAdam ellipse along the black body locus, resulting in reliable and uniform color from fixture to fixture. You ll see the results in consistently beautiful light throughout your space, whichever product you specify. Warm Glow Dimming Warm Glow Dimming provides warmth and glow once possible only in dimmed incandescent sources. Utilizing our patented proprietary algorithm and circuitry, Warm Glow Dimming technologies precisely mimic the black body curve of a standard 100W A19 lamp by gradually transitioning from 2700K, 3000K or 3500K down to 2200K. The result is virtually indistinguishable from an incandescent light source. Color Select Tunable White Color Select represents the next innovation in color temperature control for advanced recessed downlighting. Color Select products allow users to adjust color temperature from 6000K down to 2200K while independently adjusting intensity to achieve ultimate control over the quality of light in a space with a single fixture type. Color Select interfaces with standard dimming and control systems. Page 7 LIGHTING COLLABORATORY 13 Crosby Street New York, NY showroom@usailighting.com LIGHTING HEADQUARTERS , LLC. All rights reserved. All designs protected by copyright. Covered by US Patents: 8,581,520, 8,456,109, 8,742,695, 9,671,091 and 7,832,889. Patents pending., Beve, Warm Glow Dimming and Color Select are registered trademarks of, LLC. Revised 12/212018

8 DIMMING COMPATIBILITY SELECTION GUIDE D2 / DIML2 DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D2 / DIML2 : 0-10V Dimming Driver Wiring (Dims down to 10%) 120V / 277V Leviton Lightolier (Philips) D2 / DIML2 Dimmer Compatibility Chart Dimmed Light Part Number Output Range ilux dimmer expansion module DIN Rail dimmer DIN Rail analog output module 8 Channel dimmer module 8 Channel dimmer module IllumaTech dimmer Vega Diva S-EXP-DIMFLV DIN-4DIMFLV4 DIN-A08 GLX-DIMFLV8 GLXP-DIMFLV8 IP710-DLX V2000FAMU DVTXX Qty Fixtures Per Dimmer* Use source current per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating. * NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details. D2 / DIML2 0-10V DIMMING W/RELAY TO SWITCH POWER DIMMER: 0-10V 0-10V (-) GRAY 0-10V (+) PURPLE NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together. ASS 2 CONTROL WIRES RELAY DIMMER: 0-10V w/ POWER SWITCHING D2 / DIML2 0-10V DIMMING (NO RELAY) 0-10V (-) GRAY 0-10V (+) PURPLE NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together. GROUND T F , LLC. All rights reserved. All designs protected by copyright. I Revised 03/22/2017

9 DIMMING COMPATIBILITY SELECTION GUIDE D3 / DIML3 DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D3 / DIML3 : Hi-Lume A-Series 2 Wire Fwd Phase (with neutral) / Dimming Driver Wiring (Dims down to 1%) 120V D3 / DIML3 Dimmer Compatibility Chart 120V Only ETC ETC Part Number Dimmed Light Output Range Sensor+ Cabinet Unison DRd Cabinet Maestro Wireless 600W dimmer Maestro Wireless 1000W dimmer HomeWorks QS adaptive dimmer HomeWorks QS 600W dimmer HomeWorks QS 1000 W dimmer Caseta Wireless Pro 1000W dimmer Stanza dimmer RadioRA 2 adaptive dimmer RadioRA W dimmer myroom DIN power module HomeWorks QS wallbox power module Homeworks DIN power module HomeWorks wallbox power module GRAFIK Eye QS control unit GRAFIK Eye 3000 control unit RPM-4U module RPM-4A module GP dimming panels Ariadni 250W dimmer Diva 250W dimmer Grafik T or RF dimmer Nova T 250W dimmer ELV10 ELV10 MRF2-6ND-120MRF2-10ND-120HQRD-6NAHQRD-6NDHQRD-10NDPD-10NXDSZ-6NDRRD-6NARRD-10NDMQSE-4A1-D HQRJ-WPM-6D-120LQSE-4A1-D HWI-WPM-6D-120 QSGR-, QSGRJGRX-3100-, GRX-3500HW-RPM-4U-120, LP-RPM-4U-120 HW-RPM-4A-120, LP-RPM-4A-120 Various AY-253PD253P-, DVSC-253PGT-250M-, GTJ-250MNT %-1% 100%-1% 100%-1% 100%-1% Qty Fixtures Per Dimmer* Fixture Wattage 39W and Less 40W - 80W * NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details. D3 / DIML3 2 WIRE PHASE DIMMING DIMMER: 2 WIRE PHASE GROUND ONLY FOR SWITCHES WITH T F , LLC. All rights reserved. All designs protected by copyright. I Revised 03/22/2017

10 DIMMING COMPATIBILITY SELECTION GUIDE D4E / DIML4E and D4H /DIML4H DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D4E / DIML4E : 5 Series EcoSystem Driver / Dimming Driver Wiring (Dims down to 5%) 120V / 277V D4E / DIML4E EcoSystem Dimmer Compatibility Chart Dimmed Light Part Number Output Range PowPak dimming module Energi Savr Node GRAFIK Eye QS (120V ONLY) Quantum RMJ-ECO32-DB QSN-1ECO-S, QSN-2ECO-S QSGRJ-_E, QSGR-_E Various 100% 5% 100% 5% 100% 5% 100% 5% Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W * NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details. D4H / DIML4H : H Series EcoSystem Driver with Fade to Black (dims down to 1%) 120V / 277V D4H / DIML4H EcoSystem Dimmer Compatibility Chart Dimmed Light Part Number Output Range PowPak dimming module Energi Savr Node GRAFIK Eye QS (120V ONLY) Quantum RMJ-ECO32-DB QSN-1ECO-S, QSN-2ECO-S QSGRJ-_E, QSGR-_E Various 100% 1% 100% 1% 100% 1% 100% 1% Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W * NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details. D4E / DIML4E and D4H / DIML 4H EcoSystem CONTROLS ECOSYS BUS E2 E1 E2 E1 WALL CONTROL PURPLE GRAY PURPLE T F , LLC. All rights reserved. All designs protected by copyright. I EH Revised 03/22/2017

11 DIMMING COMPATIBILITY SELECTION GUIDE D6A / DIML6A and D6E / DIML6E D6B / DIML6B and D6F / DIML6F IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D6A / DIML6A and D6E / DIML6E Dimming Compatibility Table D6A / DIML6A and D6E / DIML6E are linearly programmed dimming drivers for use with logarithmic-style dimming controls (e.g., and others listed in the table below) D6A / DIML6A = Eldo SOLOdrive 0-10V control dims from 100% to 0.1% D6E / DIML6E = Eldo ECOdrive 0-10V control dims from 100% to 1% D6A / DIML6A and D6E / DIML6E Dimmer Compatibility Chart 120V & 277V Sensor Switch enlighted Part Number Diva Nova T Energi Savr Node GP Dimming Panels Interfaces nio Control Unit DVTV/NFTV with PP-20 NTFTV with PP-20 QSN-4T16-S TVM2 Module GRX-TVI w/ GRX3503 nio EZ CU-3E-1R Dimmed Light Output Range DIML6A 6E 99% - 0.1% 1% 99% - 0.1% 1% 99% - 0.1% 1% Qty Fixtures Per Dimmer* Refer to manufacturer's dimmer load rating for maximum and minimum fixture quantities per dimmer. Enlighted compatible. D6B / DIML6B and D6F / DIML6F Dimming Compatibility Table D6B / DIML6B and D6F / DIML6F are logarithmic-programmed dimming drivers for use with linear-style dimming controls (e.g.,, non- and others listed below) D6B / DIML6B = Eldo SOLOdrive 0-10V control dims from 100% to 0.1% D6F / DIML6F = Eldo ECOdrive 0-10V control dims from 100% to 1% D6B / DIML6B and D6F / DIML6F Dimmer Compatibility Chart 120V & 277V Bush-Jaeger Jung Leviton Lightolier (Philips) Merten Pass & Seymour Watt Stopper Synergy ABB enlighted Part Number Electronic potentiometer Electronic potentiometer Iluma Tech dimmer Momentum (120V ONLY) Electronic potentiometer Titan Miro Wallbox Dimmers i-bus Modules Green Light Green Light Power Pack DIN Rail Analog Output Module DIN Rail 0-10V Fluorescent Dimmer ilux 0-10V Dimmer Expansion Module Control Unit 2112U IP710-DLX ZP600FAM CD4FB-W DV1 ISD BC SD/S GLX-DIMFLV8, GLXP-DIMFLV8 GLPAC-DIMFLV4-, GLPAC-DIMFLV8GLPP-DIMFLVEX-PM, GLPP-1DIMFLV2EX-PM, GLPP-1DIMFLV3EX-PM DIN-A08 DIN-4DIMFLV4 S-EXP-DIMFLV CU-3E-1R Dimmed Light Output Range DIML6B 6F Qty Fixtures Per Dimmer* Refer to manufacturer's dimmer load rating for maximum and minimum fixture quantities per dimmer. Enlighted compatible. DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. D6 / DIML6 0-10V DIMMING W/RELAY TO SWITCH POWER 0-10V (-) GRAY 0-10V (+) PURPLE D6 / DIML6 0-10V DIMMING (NO RELAY) DIMMER: 0-10V GROUND ASS 2 CONTROL WIRES DIMMER: 0-10V w/ POWER SWITCHING 0-10V (-) GRAY 0-10V (+) PURPLE RELAY DIML6A, 6B 0-10V DIMMING (NO RELAY) DIMMER: 0-10V w/ POWER SWITCHING T F , LLC. All rights reserved. All designs protected by copyright. I Revised 08/14/2017

12 DIMMING COMPATIBILITY SELECTION GUIDE D7 / DIML7 and D7E DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D7 / DIML7 and D7E Dimming Driver Wiring D7 / DIML7 and D7E are linearly programmed dimming drivers. D7 / DIML7 = Eldo SOLOdrive DALI control dims from 100% to 0.1% D7E = Eldo ECOdrive DALI control dims from 100% to 1% D7 / DIML7 / D7E DALI CONTROLS DALI BUS DA DA WALL CONTROL ORANGE (-) ORANGE/ (+) T F , LLC. All rights reserved. All designs protected by copyright. I Revised 08/14/2017

13 DIMMING COMPATIBILITY SELECTION GUIDE D15 / DIML15 DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D15 / DIML15 : 0-10V, 347V Dimming Driver Wiring (Dims down to 1%) 347V Only 347 Acuity Douglas Hubbell Leviton Leviton D15 / DIML15 Dimmer Compatibility Chart Dimmed Light Output Range Synergy ISD-BC WPN-5721, WPN-5822 Light Hawk2 LHD-IRS3-N347-xx Illumatech IP710-DLZ with 347V relay Centura Fluorescent Control System Nova NFT* dimmer plus 347V relay Diva DVT* dimmer plus 347V relay Qty Fixtures Per Dimmer* Use source current per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating. * NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details. D15 / DIML V DIMMING W/RELAY TO SWITCH POWER DIMMER: 0-10V 0-10V (-) GRAY 0-10V (+) PURPLE NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together. ASS 2 CONTROL WIRES RELAY DIML2 0-10V DIMMING (NO RELAY) DIMMER: 0-10V w/ POWER SWITCHING 0-10V (-) GRAY 0-10V (+) PURPLE GROUND T F NOTE: Quickship fixtures are shipped prewired for 0-10V dimming controls. If switched, nondimming operation is desired, cap off purple and gray wires separately at installation. Do NOT cap purple and gray wires together , LLC. All rights reserved. All designs protected by copyright. I Revised 03/22/2017

14 DIMMING COMPATIBILITY SELECTION GUIDE D19 / DIML19 DIMMING WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together). D19 / DIML19 : Hatch XTC series or equivalent - Forward and Reverse Phase Dimming Driver. Dims down to 1% contingent upon dimmer specification and load. 120V only. D19 / DIML19 2 WIRE PHASE DIMMING DIMMER: 2 WIRE PHASE GROUND ONLY FOR SWITCHES WITH D19 / DIML19 Dimmer Compatibility Chart 120V ONLY Forward Phase / TRIAC Dimming Qty Fixtures Per Dimmer Leviton IPL06-10Z Use fixture wattage per 6613-xxx fixture specification S-600P sheet to determine S-603P number of fixtures D600P per dimmer. Max number D603P of fixtures is limited by DVSC-603P dimmer load rating. CT-600P CT-603P 120V ONLY Reverse Phase / ELV Dimming Leviton 6615 IPE04-xxx NTEL300 NTEL600 SEL300P SEL303P DVEL300P DVEL303P Qty Fixtures Per Dimmer Use fixture wattage per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating. T F , LLC. All rights reserved. All designs protected by copyright. I Revised 03/22/2017