SECTION Power over Ethernet (PoE) Enabled Camera Housing Moog Videolarm SM5, ACH13, FDW75

Transcription

1 SECTION Power over Ethernet (PoE) Enabled Camera Housing Moog Videolarm SM5, ACH13, FDW75 DIVISION 28 ELECTRONIC SAFETY AND SECURITY ELECTRONIC SURVEILLANCE Video Surveillance Video Surveillance Remote Devices and Sensors [FILE NAME]

2 PART 1 GENERAL 1.01 SUMMARY A. Section Includes SECTION Power over Ethernet (PoE) Enabled Camera Housing Moog Videolarm SM5, ACH13, FDW75 1. Outdoor camera housing system with external Ethernet or Power over Ethernet (PoE) connection to allow power sourcing to all components within hosing, including camera and integral heater and blower. B. Related Requirements Electrical (Division 26) a Common Work Results for Electrical b Schedules for Electrical c Commissioning of Electrical Systems d Low Voltage Electrical Distribution e Electrical and Cathodic Protection Electronic Safety and Security (Division 28) a Common Work Results for Electronic Safety and Security b Schedules for Electronic Safety and Security c Commissioning of Electronic Safety and Security d Video Surveillance Systems Infrastructure 1.02 REFERENCES A. Abbreviations and Acronyms 1. CCTV Closed Circuit Television B. Reference Standards 1.03 SUBMITTALS 1. Federal Communications Commission (FCC), Code of Federal Regulations, Title 47, Part European Union - EN Safety of Information Technology Equipment (ITE) 3. IEC Classification of Environmental Conditions 4. IEC Environmental Testing 5. ANSI/ IEC Degrees of Protection Provided by Enclosures 6. International Electrotechnical Commission (IEC) - Ingress Protection Rating IP55 7. National Electrical Manufacturers Association (NEMA) - 4 Enclosure Rating 8. Institute of Electronic and Electrical Engineers (IEEE) standards C. Product Data 1. Manufacturer s printed or electronic data sheets 2. Manufacturer s installation and operation manuals 3. Warranty documentation [FILE NAME]

3 1.04 QUALITY ASSURANCE A. Qualifications 1. The system, including housing, shall be manufactured in the United States, using ISO 9001 certified procedures. 2. Manufacturer of system shall have a minimum of three years experience of successful manufacture and installation of systems equivalent in function to the system proposed herein. 3. Installation contractor shall be factory authorized to install, service and maintain the system by the system manufacturer DELIVERY, STORAGE AND HANDLING A. Delivery, storage, and handling of the system shall be in accordance with the manufacturer s recommendations. B. The manufacturer s ordering instructions and lead-time requirements shall be followed to avoid delivery and installation delays WARRANTY A. Manufacturer shall provide a limited warranty for the outdoor camera housing system to be free from defects in material or workmanship for a minimum period of five years. [FILE NAME]

4 PART 2 - PRODUCTS 2.01 EQUIPMENT A. Manufacturer: Moog Videolarm 2525 Park Central Blvd. Decatur, GA USA 1100 Abernathy Road Phone +1 (770) Fax +1 (770) B. Model: [ Compact surface-mount dome housing for PoE enabled fixed and PTZ cameras - SM5C8N, SM5C8NE or equivalent] [ Outdoor environmental housing for PoE fixed camera - ACH13HB8N, ACH13HB8NE or equivalent] [Outdoor wall-mount dome housing for PoE and PoE Plus enabled fixed cameras - FDW75CF8N, FDW75CF8NE or equivalent] [Outdoor wall-mount dome housing for PoE and PoE Plus enabled PTZ cameras - FDW75C8N, FDW75C8NE or equivalent] Note: Use E-suffix model numbers when mid-span injector is to be supplied as a separate unit. Models without the E-suffix include an internal mid-span injector supplied with the unit. C. Substitutions: Not Permitted D. All PoE housing units shall be supplied from a single manufacturer 2.02 DESCRIPTION A. The PoE enabled camera housing ( the PoE housing ) shall be an outdoor capable integrated camera housing system allowing the PoE camera to be powered directly via its Ethernet connection. B. Components - The PoE housing shall include the following primary components: C. Power 1. External housing 2. Heater assembly a. The heater shall activate at 60 F and deactivate at 80 F. 3. Blower assembly 4. Printed circuit (PC) board a. The PC board shall receive power from the PoE connection and provide appropriate power to the camera and heater and blower assemblies. 1. The PoE housing shall feature dynamic power allocation to apportion power among camera, heater, and blower. a. Both camera and heater shall run directly on PoE power. b. The PC board shall provide maximum power to the camera, with remaining power provided to the heater and blower for maximum operating temperature range 2. The PoE housing shall be PoE Plus (IEEE802.3at) compliant. a. [PoE power to the housing shall be from an IEEE 802.3at compliant mid-span injector or Ethernet PoE switch.] [PoE power to the housing shall be from the internal IEEE compliant mid-span injector.] Note: Insert the following when power is to be sourced from an external mid-span injector or PoE switch. b. [PoE power sourced to the surface-mount dome housing shall be a minimum of 30W over a distance not to exceed 328 feet (100m).] [PoE power sourced to the outdoor environmental housing for PoE fixed camera shall be a minimum of 30W over a distance not to exceed 328 feet (100m).] [PoE power sourced to the outdoor wall- [FILE NAME]

5 D. Cameras mount dome housing for PoE and PoE Plus enabled PTZ cameras shall be a minimum of 60W over a distance not to exceed 262 feet (80m).] 1. Acceptable cameras: Note: Use the following for SM5 series surface-mount dome housing. a. Arecont: AV13**/21**/28**/31**/51**/10005 b. Axis: M10**, 212,216 c. IQivision (IQeye): 5xx/7xx series d. Panasonic: BB-HCM381/280, WV-NF284/302, WV-NS202, WV-SC385 e. Sony: SNC-DH140/240 f. Toshiba: IKWB21A Note: Use the following for ACH13 outdoor environmental housing for PoE fixed camera. a. Standard fixed camera body with camera and lens combinations up to 10.5" long and 3.6" wide Note: Use the following for FDW75 outdoor environmental housing for outdoor wall-mount dome housing for PoE and PoE Plus enabled PTZ cameras.. E. Accessories a. Sony: SNC-RH124, RS44, RS46 1. Brackets for wall, corner, and pole mount 2. Sunshields 2.03 SPECIFICATIONS A. Materials 1. Body Extruded aluminum polycarbonate 2. Trim ring/end caps Polycarbonate 3. Window dome Polycarbonate B. Electrical 1. External Voltage a. Internal PoE 100/240 VAC (50-60 Hz) b. External PoE VDC (from PoE switch or mid-span injector) 30 W minimum for surface mount fixed/ptz dome (SM5) 30 W minimum for wall/pole mount fixed (ACH13) 60 W minimum for wall mount fixed/ptz dome (FDW75) Note: Recommended mid-span injectors are: PowerDsine: 9000G, 9001G, 9501G Philong: PoE36*, PoE125*, PoE30*, PoE75* (+60 watt models needed for FDW75 series) C. Mechanical 1. Weight (subtract 1 lb. (.5 kg) when PoE is sourced externally) a. Surface mount fixed/ptz dome (SM5) 3 lbs. (1.4 kg) b. Wall/pole mount fixed (ACH13) 4 lbs. (1.8 kg) [FILE NAME]

6 c. Wall mount fixed/ptz dome (FDW75) 10 lbs. (4.6 kg) 2. Dimensions D. Environmental a. Surface mount fixed/ptz dome (SM5) 8.6" x 8.6" x 8.4" (21.8cm x 21.8cm x 21.3cm) b. Wall/pole mount fixed (ACH13) 15.4" x 5.7" x 15.3" (39.1cm x 14.5cm x 38.9cm) c. Wall mount fixed/ptz dome (FDW75) 14.5" x 10.3" x 14.8" (36.8 cm x 26.2cm x 37.6cm) 1. Temperature a. Operating Temperature: -20 F to 120 F (-29 C to + 49 C) b. Heater Operation 1) Activation 60 F +/-8 (15 C, +/-8 ) 2) De-activation 80 F +/-8 (27 C, +/-8 ) 2. Certifications and Ratings (IP/NEMA Rating) 2.05 SOURCE QUALITY CONTROL a. Surface mount fixed/ptz dome (SM5) IP66/4X b. Wall/pole mount fixed (ACH13) IP55/3R c. Wall mount fixed/ptz dome (FDW75) IP66/4X A. Tests and Inspections 1. A test report shall be submitted to indicate that each system was tested successfully in a factory system test to meet manufacturer s published specifications. PART 3 - EXECUTION 3.01 INSTALLERS A. Installation should be performed by qualified service personnel only in accordance with the National Electrical Code and applicable local codes. B. The Contractor s installers and technicians shall be factory trained and certified to install, service and maintain the system INSTALLATION A. The system shall ship from the factory fully assembled, tested and ready for installation and use. B. Care shall be exercised to select suitable hardware to install the unit, taking into account both the composition of the mounting surface and the weight of the unit SUPPORT A. The camera shall be supported by U.S. technical assistance program from the manufacturer and local technical assistance program from a certified and trained professional services company in the country in which the system is installed. END OF SECTION [FILE NAME]