SVENSK STANDARD SS-EN ISO 15973

Size: px

Start display at page:

Download "SVENSK STANDARD SS-EN ISO 15973"

Gordon Joseph
5 years ago
Views:

SVENSK STANDARD SS-EN ISO 15973 Fastställd Utgåva Sida 2000-12-29 1 1 (1+8) Copyright SIS. Reproduction in any form without permission is prohibited.

1 SVENSK STANDARD SS-EN ISO Fastställd Utgåva Sida (1+8) Copyright SIS. Reproduction in any form without permission is prohibited. Closed end blind rivets with break pull mandrel and protruding head AIA/St (ISO 15973:2000) Fästelement Blindnitar av splinttyp med kullrigt huvud AlA/St (ISO 15973:2000) The European Standard EN ISO 15973:2000 has the status of a Swedish Standard. This document contains the official English version of EN ISO 15973: Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden EN ISO 15973:2000 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN ISO 15973:2000. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, STOCKHOLM Telefon: Telefax: E-post: sis.sales@sis.se. Internet: Upplysningar om sakinnehållet i standarden lämnas av SIS (SMS). Telefon: Telefax: E-post: info@sms-standard.se Tryckt i maj 2001

3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO December 2000 ICS English version Closed end blind rivets with break pull mandrel and protruding head - AlA/St (ISO 15973:2000) Rivets aveugles à rupture de tige à corps fermé, à tête bombée - AlA/St (ISO 15973:2000) Geschlossene Blindniete mit Sollbruchdorn und Flachkopf - AlA/St (ISO 15973:2000) This European Standard was approved by CEN on 15 December CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15973:2000 E

4 Page 2 EN ISO 15973:2000 Provläsningsexemplar / Preview Foreword Corrected The text of the International Standard ISO 15973:2000 has been prepared by Technical Committee ISO/TC 2 "Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2001, and conflicting national standards shall be withdrawn at the latest by June According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 15973:2000 was approved by CEN as a European Standard without any modification. NOTE: Normative references to International Standards are listed in annex ZA (normative).

5 Page 3 EN ISO 15973:2000 Closed end blind rivets with break pull mandrel and protruding head AIA/St 1 Scope This International Standard specifies dimensional and mechanical characteristics and application data for closed end blind rivets with break pull mandrel and protruding head, with an aluminium alloy body (AlA) and a steel mandrel (St) and with nominal diameters from 3,2 mm up to and including 6,4 mm. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 3269:2000, Fasteners Acceptation inspection. ISO 14588:2000, Blind rivets Terminology and definitions. ISO 14589:2000, Blind rivets Mechanical testing. 3 Dimensions NOTE Symbols and designations of dimensions are specified in ISO Rivet dimensions See Figure 1 and Table 1. Figure 1 Rivet dimensions

6 Page 4 EN ISO 15973:2000 Provläsningsexemplar / Preview Table 1 Rivet dimensions Dimensions in millimetres Rivet nom. 3,2 4 4,8 6,4 d max. 3,28 4,08 4,88 6,48 min. 3,05 3,85 4,65 6,25 d k max. 6,7 8,4 10,1 13,4 min. 5,8 6,9 8,3 11,6 k max. 1,3 1,7 2 2,7 d m max. 1,85 2,35 2,77 3,71 Mandrel p min l nom. = min. max. Recommended grip ranges a 6,5 7,5 0,5 to 2, ,0to3,5 0,5to3,5 8,5 9,5 0,5 to 3,5 9,5 10,5 3,5 to 5,0 3,5 to 5,0 3,5 to 5, ,0to6,5 5,0to6,5 5,0to6,5 12,5 13,5 6,5 to 8,0 6,5 to 8,0 1,5 to 6, ,5 to 8,0 14,5 15,5 8 to 10 8,0 to 9,5 15,5 16,5 6,5 to 9, ,5 to 11, to to 16 NOTE The rivet body dimensions are generated from the design formulae specified in annex A (informative). a The grip ranges of rivets with dimensions as given in this table and with the material combination as given in clause 4 are specified by the minimum and maximum grip lengths. The minimum grip lengths are given as a recommendation only. It may be possible to apply lower minimum values in certain cases. 3.2 Clearance hole diameters The clearance hole (d h1 ) to accommodate the rivet in the components to be fastened is shown in Figure 2 and its diameters are given in Table 2. Nonconformance to the values in Table 2 may result in assembly difficulties and/or reduction in the shear and tensile loads specified in Table 3. If necessary, to facilitate alignment, only the component on the access side may have a clearance hole larger than specified in Table 2, see Figure 2. This may also result in a reduction of the shear and tensile loads specified in Table 3.

Fästelement Blindnitar av splinttyp med genomgående hål och sänkhuvud AIA/St (ISO 15978:2002)

SVENSK STANDARD SS-EN ISO 15978 Fastställd 2002-11-22 Utgåva 1 Fästelement Blindnitar av splinttyp med genomgående hål och sänkhuvud AIA/St (ISO 15978:2002) Open end blind rivets with break pull mandrel