3M Detection System Model 9100

Transcription

1 3M Detection System Model 9100 Training Guide Welcome and thank you for choosing the 3M Model 9100 Detection system. This training guide is a review of the basics of operating the 3M detection system. For more detailed information about the system, see Additional information sources. Turn the system on and off Verify the system operation Check the patron count Reset the patron counter Adjust alarm volume Clean lattices Additional information sources 3M Command Center 3M Detection System Model 9100 Training Guide, Rev A.

2 Turn the system on and off 1. Locate the key switch, which controls power to the system, on an end lattice. 2. Use the key to power the system on and off. Note: The key can be inserted and removed in either the OFF (0) or ON (1) positions. Turn the key to the 0 position for OFF 1 position for ON

3 Verify the system operation The system can be configured to alarm when exiting only, entering only, exiting and entering, or for whenever it detects a secured tag. Verify the system is alarming for the way it is configured by walking through the corridor with an item that is known to be in a secured state. Note: The alarming option is configurable at installation by the installing technician or anytime by library staff using the optional 3M Command Center software. Check the patron count Patron counter The patron counter tracks the number of patrons entering and exiting through all corridors. It also keeps a total count. The patron counter display is located on one of the lattices as shown. and arrows indicate the direction for the count (in or out of the library). The = sign indicates the total for both directions. The display automatically cycles through the three counts. Optional 3M Command Center software collects patron count statistics that can be viewed by staff using a web interface.

4 Reset the patron counter 1. Record the total patron count before resetting the counter (in order to track totals). 2. Locate the patron count access hole beneath the patron count display. 3. Reset the counter by inserting the pointed end of a bent paper clip into the access hole and pressing the reset button. You will know the reset operation was successful when the count is zeroed out. Patron Counter Access hole Paper clip Note: Optional 3M Command Center software collects patron count statistics that can be reset by staff using the web interface. DT_9100_patron_count_reset

5 Adjust alarm volume 1. Locate the alarm adjustment mechanism, which is near the alarm speaker and on the same lattice as the patron counter. 2. Adjust the alarm volume by doing the following: (a) Have someone stand in a detection system corridor with a secured RFID tag so that the alarm sounds continually. (b) Insert a paper clip or small screw driver through the alarm adjustment opening and move the adjustment mechanism back and forth until you find the right volume. Paper clip Note: Optional 3M Command Center software can be used to adjust the light flashing and beep duration and to choose the alarm light color. The installing technician will set these parameters initially during installation. DT_9100_Lattice_alarm_adjust

6 Clean lattices Notice! Turn off the detection system before cleaning. Do not allow liquid into the lattice base because this can damage electronics. Do not use harsh chemicals, cleaning solvents, window cleaning sprays, kitchen scouring compounds, or strong detergents, which can damage lattices. Cleaning instructions Use a soft, clean, damp cloth or chamois to gently clean lattices. A 3M Scotch-Brite lens cleaning cloth is included with the system for this purpose. If required, clean an area with a cloth moistened with a solution of mild soap or detergent and lukewarm water. Rinse with clean water and dry residual moisture with a clean, soft, cloth or towel. Use an antistatic cleaner for acrylic to reduce static electricity and dust attraction.

7 Additional information sources Additional detailed information can be found in your User Instructions packaged with the product or by calling the 3M Library Systems Support at The 3M Detection System Model 9100 Owner s Manual is included on the 3M RFID Systems User Documentation CD-ROM that was supplied with your equipment. It can also be downloaded from the 3M website: (Locate the Resources heading in the left-hand column and click User Manuals, Guides & Training.)

8 3M Command Center Help enhance the productivity and performance of your library staff and equipment with the 3M Command Center. The 3M Command Center works with currently available 3M self-service systems and automated materials handling (AMH) systems, and with some 3M RFID Detection Systems. Your library will have real-time access to statistics and hardware status that will help save your staff valuable time and effort and improve the satisfaction of your library s patrons by optimizing the performance of your library equipment.