American National Standards

Transcription

1 PUBLISHED WEEKLY BY THE AMERICAN NATIONAL STANDARDS INSTITUTE 25 West 43rd Street, NY, NY VOL. 46, #42 October 16, 2015 Contents American National Standards Call for Comment on Standards Proposals... 2 Call for Members (ANS Consensus Bodies)... 9 Final Actions Project Initiation Notification System (PINS) ANS Maintained Under Continuous Maintenance ANSI-Accredited Standards Developers Contact Information International Standards ISO and IEC Draft Standards ISO and IEC Newly Published Standards Proposed Foreign Government Regulations Information Concerning American National Standards Call for comment on proposals listed This section solicits public comments on proposed draft new American National Standards, including the national adoption of ISO and IEC standards as American National Standards, and on proposals to revise, reaffirm or withdraw approval of existing American National Standards. A draft standard is listed in this section under the ANSI-accredited standards developer (ASD) that sponsors it and from whom a copy may be obtained. Comments in connection with a draft American National Standard must be submitted in writing to the ASD no later than the last day of the comment period specified herein. Such comments shall be specific to the section(s) of the standard under review and include sufficient detail so as to enable the reader to understand the commenter's position, concerns and suggested alternative language, if appropriate. Please note that the ANSI Executive Standards Council (ExSC) has determined that an ASD has the right to require that interested parties submit public review comments electronically, in accordance with the developer s procedures. Ordering Instructions for "Call-for-Comment" Listings 1. Order from the organization indicated for the specific proposal. 2. Use the full identification in your order, including the BSR prefix; for example, Electric Fuses BSR/SAE J Include remittance with all orders. 4. BSR proposals will not be available after the deadline of call for comment. Comments should be addressed to the organization indicated, with a copy to the Board of Standards Review, American National Standards Institute, 25 West 43rd Street, New York, NY Fax: ; psa@ansi.org * Standard for consumer products 2015 by American National Standards Institute, Inc. ISSN ANSI members may reproduce for internal distribution. Journals may excerpt items in their fields

2 Comment Deadline: November 15, 2015 ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda BSR/ASHRAE/ASHE Addendum 170ad-201x, Ventilation of Health Care Facilities (addenda to ANSI/ASHRAE Standard ) This proposed addendum subdivides examination rooms beyond the current division of emergency and non-emergency rooms and establishes air change rates commensurate with the risk within those specialized rooms. Administrative controls (such as assignment of patients to specialized rooms) are an important preventive strategy to supplement the benefit of environmental controls. As such, these administrative controls would be applied to people presenting with undiagnosed gastrointestinal, respiratory, or skin infection symptoms, e.g., phone triage, prompt triage to an area away from others, and assignment to a Special Examination Room. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Online Comment Database at ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda BSR/ASHRAE/ASHE Addendum 170c-201x, Ventilation of Health Care Facilities (addenda to ANSI/ASHRAE Standard ) This proposed addendum updates the terminology used for laboratories to align with FGI-2014 (reference ) and includes provisions to reduce air total change rates in these spaces in certain circumstances. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Online Comment Database at ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda BSR/ASHRAE/ASHE Addendum 170f-201x, Ventilation of Health Care Facilities (addenda to ANSI/ASHRAE Standard ) This proposed addenda clarifies requirements for the Primary Supply Diffuser Array. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Online Comment Database at ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda BSR/ASHRAE/ASHE Addendum 170h-201x, Ventilation of Health Care Facilities (addenda to ANSI/ASHRAE Standard ) Currently, in the industry there is a discrepancy in several requirements for environmental conditions in areas of the Sterile Processing Department (SPD) between ASHRAE standards and AAMI standards. ASHRAE standards guide the design of these areas, while AAMI standards guide the operation of these areas. Therefore, some amount of agreement is required between these two groups. In April of 2015 representatives of ASHRAE, AAMI, FGI, AORN, ASHE and APIC met to discuss these issues. This proposed addendum represents the recommendations for space temperature in several spaces from this group. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Online Comment Database at UL (Underwriters Laboratories, Inc.) Revision BSR/UL X, Standard for Safety for Alarm Valves for Fire-Protection Service (revision of ANSI/UL (R1013)) Revises the Hydrostatic Test Requirements in the Strength of Body Test, 28.1 and Bolt Strength, 10.13; Pressure Gauge Updates, Revised 26.2 and Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Linda Phinney, (408) , Linda.L.Phinney@ul.com UL (Underwriters Laboratories, Inc.) Revision BSR/UL x, Standard for Safety for Electric Fans (revision of ANSI/UL a) (9) Temperature Test Table 36.1; (11) New requirements for smart enabled fans. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Susan Malohn, (847) , Susan.P.Malohn@ul.com UL (Underwriters Laboratories, Inc.) Revision Standards Action - October 16, Page 2 of 43 Pages BSR/UL X, Reference Standard for Electrical Wires, Cables, and Flexible Cords (revision of ANSI/UL ) This proposal includes the following revisions: (1) Revision to Table 47.1 to add and correct references. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Ross Wilson, (919) , Ross.Wilson@ul.com

3 Standards Action - October 16, Page 3 of 43 Pages Comment Deadline: November 30, 2015 AAMI (Association for the Advancement of Medical Instrumentation) Reaffirmation BSR/AAMI/ISO x, Medical devices - Quality management - Medical device nomenclature data structure (reaffirmation of ANSI/AAMI/ISO ) This International Standard provides rules and guidelines for a medical device nomenclature data structure, in order to facilitate cooperation and exchange of data used by regulatory bodies on an international level between interested parties, e.g., regulatory authorities, manufacturers, suppliers, health care providers, and end users. Single copy price: Free Obtain an electronic copy from: org/kws/public/document?document_id=7247&wg_abbrev=public_rev Order from: document_id=7247&wg_abbrev=public_rev Send comments (with copy to psa@ansi.org) to: wvargas@aami.org ACCA (Air Conditioning Contractors of America) Revision BSR/ACCA 2 Manual J x, Residential Load Calculations (revision of ANSI/ACCA 2 Manual J-2011) The provisions of the revised standard apply to any dwelling unit that has its own heating-cooling-ventilating system and equipment, and its own exhaust air system(s). This includes: single-family detached structures, duplex structures, and triplex structures; single-family attached structures (row house or town house); the dwelling units in multi-family attached structures (condo units and apartment units); and energy-efficient homes. Single copy price: Free review copy Obtain an electronic copy from: and response form Order from: Luis Escobar, (703) , luis.escobar@acca.org ASABE (American Society of Agricultural and Biological Engineers) New Standard BSR/ASABE S629 MONYEAR-201x, Framework to Evaluate the Sustainability of Agricultural Production Systems (new standard) The Standard is intended to define frameworks for sustainability certification of all types of farming operations (which includes ranching) typically found in North America. It does not constitute a certification framework per se, but rather serves as a criterion for development of certification. KPI improvement in agricultural sustainability for this framework includes producers and processors from cradle to farm and/or factory gate, across the primary categories of sustainability (economic, ecological, and social). Sustainable Agriculture shall exclude the farm residence, except where it is not practical to separate baseline data. Single copy price: $58.00 Obtain an electronic copy from: walsh@asabe.org Order from: Jean Walsh, (269) , walsh@asabe.org BHMA (Builders Hardware Manufacturers Association) Revision BSR/BHMA A x, Architectural Door Trim (revision of ANSI/BHMA A ) This Standard contains requirements for door protection plates, door edgings, push plates, door pulls, push bars, and pull bars. Included are strength and finish tests, and dimensional and material criteria. Single copy price: $36.00 (Nonmembers)/$18.00 (BHMA members) Obtain an electronic copy from: mtierney@kellencompany.com Order from: Emily Brochstein, (212) , ebrochstein@kellencompany. com BHMA (Builders Hardware Manufacturers Association) Revision BSR/BHMA A x, Door Controls - Overhead Stops and Holders (revision of ANSI/BHMA A ) This Standard establishes requirements for overhead door stops and holders, and includes performance tests covering operational, cyclical, strength, and finish criteria. Single copy price: $36.00 (Nonmembers)/$18.00 (BHMA members) Obtain an electronic copy from: mtierney@kellencompany.com Order from: Emily Brochstein, (212) , ebrochstein@kellencompany. com Send comments (with copy to psa@ansi.org) to: Michael Tierney, (212) , mtierney@kellencompany.com BHMA (Builders Hardware Manufacturers Association) Revision BSR/BHMA A x, Release Devices - Closer Holder, Electromagentic and Electromechanical (revision of ANSI/BHMA A ) This Standard establishes requirements for door closers combined with holdopen devices or free-swinging door closers combined with releasing devices and includes performance tests covering operational, cyclical, and finish criteria. Single copy price: $36.00 (Nonmembers)/$18.00 (BHMA members) Obtain an electronic copy from: mtierney@kellencompany.com Order from: Emily Brochstein, (212) , ebrochstein@kellencompany. com Send comments (with copy to psa@ansi.org) to: Michael Tierney, (212) , mtierney@kellencompany.com CSA (CSA Group) Revision BSR LC 1-201x, Gas Piping Systems Using Corrugated Stainless Steel Tubing (CSST) (same as CSA x) (revision of ANSI LC ) This standard details test and examination criteria for fuel gas piping systems, using corrugated stainless steel tubing, intended for installation in residential or commercial buildings, and including all components supplied or specified by the manufacturer to convey and control fuel gas to all appliances served. This standard does not apply to gas connectors for appliances. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) x88321, cathy.rake@csagroup.org

4 Standards Action - October 16, Page 4 of 43 Pages CSA (CSA Group) Revision BSR Z x, Standard for Commercial Dishwashers (same as UL 921) (revision of ANSI Z83.21/CSA C22.2 No. 168/UL (R2010)) Details for test and examination of commercial gas-fired and electric dishwashers for use with natural, manufactured and mixed, and liquefied petroleum gases, and LP gas-air mixtures. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) x88321, cathy.rake@csagroup.org ISA (International Society of Automation) Revision BSR/ISA x, Face-to-Centerline Dimensions for Flanged Globe- Style Angle Control Valve Bodies (Classes 150, 300, and 600) (revision of ANSI/ISA (R2007)) This standard aids users in their piping design by providing Classes 150, 300, and 600 raised-face flanged globe-style angle control valve face-tocenterline dimensions without giving special considerations to the equipment manufacturer to be used. Single copy price: $40.00 Obtain an electronic copy from: ebrazda@isa.org Order from: Eliana Brazda, (919) , ebrazda@isa.org NASBLA (National Association of State Boating Law Administrators) New Standard BSR/NASBLA X, Basic Boating Knowledge - Human Propelled Boats (new standard) This is the minimum standard that applies to all human-propelled boating courses in the U.S. states and territories and District of Columbia. Its purpose is to establish the national standard for use by course providers to meet the needs of recreational boaters for human-propelled boating knowledge in order to identify and reduce primary risk factors and mitigate their effects on recreational boating. Single copy price: Free Obtain an electronic copy from: pam@nasbla.org Order from: Pamela Dillon, (859) , pam@nasbla.org NEMA (ASC C12) (National Electrical Manufacturers Association) Revision BSR C x, Code for Electricity Metering (revision of ANSI C ) Establishes acceptable performance criteria for new types of ac watthour meters, demand meters, demand registers, pulse devices, and auxiliary devices. Describes acceptable in-service performance levels for meters and devices used in revenue metering. Single copy price: $ Order from: NEMA Send comments (with copy to psa@ansi.org) to: Paul Orr, (703) , Pau_orr@nema.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), High-Pressure Sodium Lamps (reaffirmation and redesignation of ANSI ANSLG C ) This standard sets forth the physical and electrical requirements for HPS lamps, to ensure performance and interchangeability. The data given also provide the basis for the electrical requirements for ballasts and ignitors, as well as the lamp-related requirements for luminaires. This standard covers only single-ended HPS lamps. Lamps with internal starting devices are not covered. This standard does include improved color HPS lamps (those lamps that have a color-rendering index 60 and that operate on the same ballasts as the conventional lamps that they are intended to replace). However, color is not a standardized parameter. Luminous flux is not a standardized parameter either. This standard covers only 60 Hz operation of HPS lamps, on ballasts designed for HPS lamps. Single copy price: $ Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), Dimensions for Projection Lamps - Double-Contact, Medium Ring (Special B), Base-up Type (reaffirmation of ANSI C (R2009)) This standard establishes the dimensions essential to the interchangeability of lamps of the double-contact, medium-ring (Special B), base-up type. It is not intended to prescribe either operating characteristics or details of design, such as the shape of the ventilation ports or the method of attachment of the prefocus ring to the base. Single copy price: $50.00 Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), High Intensity Discharge Lamps - Methods of Measuring Characteristics (reaffirmation of ANSI C (R2009)) This standard describes the procedures to be followed and the precautions to be observed in measuring the electrical characteristics of high intensity discharge lamps as specified in the American National Standard Specifications for Mercury (Hg), High-pressure Sodium (HPS) and Metal Halide (MH) Lamps, as referenced in clause 2, Normative references. It is the purpose of this standard to outline methods of measurement that will make it possible to obtain reproducible and accurate measurements of High- Intensity Discharge lamp characteristics. Deviations from the procedures given in this standard are permissible for production or other testing, provided that the methods used give results in substantial agreement with the methods given herein. In cases of doubt, reference shall be made to the methods specified in the appropriate American National Standard, referenced in clause 2, to establish the validity of the results obtained by any alternate procedure. Single copy price: $ Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org

5 Standards Action - October 16, Page 5 of 43 Pages NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), Characteristics of Subminiature Lamps of T1 and T1-3/4 Shapes (reaffirmation of ANSI C ) This standard sets forth the physical and electrical characteristics of those groups of subminiature incandescent lamps with T1 and T1-3/4 bulb shapes. Lamps with various base or termination configurations are included. Single copy price: $75.00 Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org PLATO (Portable Lights American Trade Organization) Revision BSR/PLATO FL 1-201x, Flashlight Basic Performance Standard (revision of ANSI/NEMA FL1-2009) This Standards Publication covers basic performance of hand-held/portable flashlights, spotlights, and headlamps providing directional lighting. Single copy price: Free Obtain an electronic copy from: mtierney@kellencompany.com Order from: mtierney@kellencompany.com Send comments (with copy to psa@ansi.org) to: peter@plato-usa.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), Slide Projector Lamps, Condensing, Dichroic, 1.65-in. (42 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GX5.3 Bases (reaffirmation of ANSI C (R2009)) This standard consolidates the lamps commonly used for slide projectors into a single standard. The lamps contained in this standard are not to be considered as interchangeable, although physically they will all fit the common GX5.3 sockets. The photometry of each lamp is dependent upon the system for which it was designed and on the system in which it is used. A sample system and representative photometric values are found in the Annex. Single copy price: $50.00 Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), Slide Projector Lamps, Condensing, Dichroic, Two-Inch {51 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GV 5.3 Bases (reaffirmation of ANSI C (R2009)) This standard consolidates the lamps commonly used for slide projectors into a single standard. The lamps contained in this standard are not to be considered as interchangeable. Physically, they will all fit the common socket used for these lamps. The photometry of each lamp is dependent upon the system for which it was designed and on the system in which it is used. A sample system and representative photometric values are found in the Annex. Single copy price: $50.00 Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org NEMA (ASC C78) (National Electrical Manufacturers Association) Reaffirmation BSR C (R201x), Discharge Lamps (Excluding Fluorescent Lamps) - Safety Specifications (reaffirmation and redesignation of ANSI/IEC C (R2009)) This standard specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes. Single copy price: $50.00 Order from: Michael Erbesfeld, , Michael.Erbesfeld@nema.org SPRI (Single Ply Roofing Institute) Revision BSR/VF-1-201x, External Fire Design Standard for Vegetative Roof Systems (revision of ANSI/SPRI VF ) This design standard provides a method for designing external fire resistance for vegetative roofing systems. It is intended to provide a minimum design and installation reference for those individuals who design, specify, and install vegetative roofing systems. It shall be used in conjunction with the installation specifications and requirements of the manufacturer of the specific products used in the vegetative roofing system. Single copy price: Free Obtain an electronic copy from: Linda King, info@spri.org Order from: Linda King, (781) , info@spri.org TAPPI (Technical Association of the Pulp and Paper Industry) New Standard BSR/TAPPI T 556 om x, Bending resistance of paper and paperboard by single-point bending methods (new standard) This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mn of a 38 mm (1.5 in.) wide vertically clamped sample, at 15 or 7.5 deflection. For this method, the standard bending angle is 15 ± 0.1. For specimens that break or are otherwise unsuitable at 15, a bending angle of 7.5 ± 0.1 shall be used. Single copy price: Free Obtain an electronic copy from: standards@tappi.org Order from: Laurence Womack, (770) , standards@tappi.org UL (Underwriters Laboratories, Inc.) Reaffirmation BSR/UL x, Standard for Safety for Automatically Operated Roof Vents for Smoke and Heat (reaffirmation of ANSI/UL ) (1) Reaffirmation and continuance of the third edition of the Standard for Automatically Operated Roof Vents for Smoke and Heat, UL 793, as an American National Standard. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: comm2000 Send comments (with copy to psa@ansi.org) to: Amy Walker, (847) , Amy.K.Walker@ul.com

6 Standards Action - October 16, Page 6 of 43 Pages UL (Underwriters Laboratories, Inc.) Reaffirmation BSR/UL 2017, Standard for Safety for General-Purpose Signaling Devices and Systems (reaffirmation of ANSI/UL ) (1) Reaffirmation and continuance of the second edition of the Standard for General-Purpose Signaling Devices and Systems, UL 2017, as an American National Standard. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: comm2000 Send comments (with copy to psa@ansi.org) to: Amy Walker, (847) , Amy.K.Walker@ul.com UL (Underwriters Laboratories, Inc.) Revision BSR/UL x, Standard for Safety for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances (revision of ANSI/UL ) The following changes in UL 94 are being proposed: (1) Addition of Carbon Black (as colorant) to overlooked paragraphs 9.3.4, , and Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: Raymond Suga, (631) , raymond.m.suga@ul.com UL (Underwriters Laboratories, Inc.) Revision BSR/UL X, Standard for Safety for Attachment Plugs and Receptacles (Proposal dated ) (revision of ANSI/UL a) This proposal includes: (1) Addition of insertion testing for 5-15R and 5-20R normal household receptacles; (2) Receptacles identified for use with 75 C insulated conductors; and (3) Editorial correction to specify the pin material for test pin B of the grounding contact test. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: Casey Granata, (919) , Casey.Granata@UL.Com UL (Underwriters Laboratories, Inc.) Revision BSR/UL 773A-201x, Standard for Safety for Nonindustrial Photoelectric Switches for Lighting Control (revision of ANSI/UL 773A-2006 (R2011)) Requirements cover controls of the light or presence-sensitive types, or both; for indoor or outdoor service; intended for the control of loads up to a maximum of 20 A and maximum 347 V; installations on 50-Hz or 60-Hz systems or DC up to 60 V; and intended to be installed in accordance with the NEC, NFPA 70, the CEC Part I, CSA C22.2 No. 0, and NOM 001 SEDE. These requirements do not cover devices: that are locking type, used for area or roadway lighting fixtures; that monitor or control safety critical loads or personal protection circuits; intended to be installed in areas designated hazardous locations; or intended to be installed for manufacturing process control. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: Anne Marie Jacobs, (919) , annemarie.jacobs@ul.com Comment Deadline: December 15, 2015 ITI (INCITS) (InterNational Committee for Information Technology Standards) New Standard BSR/INCITS x, Information technology - Security Features for SCSI Commands (SFSC) (new standard) The set of SCSI standards specifies the interfaces, functions, and operations necessary to ensure interoperability between conforming SCSI implementations. This standard is a functional description. Conforming implementations may employ any design technique that does not violate interoperability. This standard defines security features for use by all SCSI devices. This standard defines the security model that is basic to every device model and the parameter data that may apply to any device model. Single copy price: $60.00 Obtain an electronic copy from: Order from: Rachel Porter, (202) , comments@itic.org ITI (INCITS) (InterNational Committee for Information Technology Standards) New Standard BSR/INCITS x, Information Technology - Fibre Channel - Switch Fabric - 6 (FC-SW-6) (new standard) FC-SW-6 describes the requirements for an interconnecting Fabric consisting of multiple Fabric Switch elements to support the INCITS Fibre Channel - Framing and Signaling (FC-FS-2) and INCITS Fibre Channel - Physical Interface (FC-PI-4) standards. Single copy price: $60.00 Obtain an electronic copy from: Order from: Rachel Porter, (202) , comments@itic.org ITI (INCITS) (InterNational Committee for Information Technology Standards) New Standard BSR/INCITS x, Information technology - Fibre Channel - Physical Interfaces - 6P 128GFC Four Lane Parallel (FC-PI-6P) (new standard) This standard will define the requirements for new physical layer variants that operate at FC-PI-6 line rate on a four lane physical variant. It is desirable that new variants operate at similar distances as those of the corresponding variants specified in FC-PI-6. This standard will consider all aspects of transmit, receive, and cable-plant performance requirements for optical and electrical links. The standard will enable interoperability of transmitter devices, receiver devices, interconnects, and components among different manufacturers. Single copy price: $60.00 Obtain an electronic copy from: Order from: Rachel Porter, (202) , comments@itic.org

7 Technical Reports Registered with ANSI Technical Reports Registered with ANSI are not consensus documents. Rather, all material contained in Technical Reports Registered with ANSI is informational in nature. Technical reports may include, for example, reports of technical research, tutorials, factual data obtained from a survey carried out among standards developers and/or national bodies, or information on the "state of the art" in relation to standards of national or international bodies on a particular subject. Immediately following the end of a 30-day announcement period in Standards Action, the Technical Report will be registered by ANSI. Please submit any comments regarding this registration to the organization indicated, with a copy to the PSA Center, American National Standards Institute, 25 West 43rd Street, New York, NY or to psa@ansi.org. Standards Action - October 16, Page 7 of 43 Pages ITI (INCITS) (InterNational Committee for Information Technology Standards) INCITS/ISO/IEC TR :2011, Information technology - Fibre Channel Methodologies for Interconnects - 2 (FC-MI-2) (technical report) ISO/IEC :2011(E) is intended to document interoperability behavior for Fabric elements (i.e., E_Port, F_Port, FL_Port). It includes a wide range of issues such as link initialization, error detection, error recovery, fabric operation, management capabilities, and zoning. It serves as an implementation guide, whose primary objective is to maximize the likelihood of interoperability between conforming implementations. It specifies common methodologies for both Arbitrated Loop and Switched environments. The goal of this technical report is to facilitate interoperability between devices whether they are connected in a Loop or Fabric topology. Single copy price: $ Obtain an electronic copy from: Order from: Send comments (with copy to psa@ansi.org) to: comments@itic.org Correction Public Review Announced in Error The following standard was announced as available for public comment in the October 2, 2015 issue of Standards Action in error: BSR/ASTM WK51504 ANSI/IEEE/ASTM SI 10, Standard for Metric Practice

8 Standards Action - October 16, Page 8 of 43 Pages Clarification of INCITS documents announced for comment in the August 28, 2015 issue of Standards Action Please see the clarifications below. As originally published, the comment period for these documents closes on October 27, INCITS/ISO/IEC :1994/TC1:1996[R2010] is listed as (stabilized maintenance of INCITS/ISO/IEC :1994 [S2015]) Technical Corrigendum 1 to ISO/IEC :1994; it should be (stabilized maintenance of INCITS/ISO/IEC :1994/TC 1:1996 [R2010]) INCITS/ISO/IEC 17913:2000[2010] is listed as (reaffirmation of INCITS/ISO/IEC 17913:2000 [2000]); this should be (reaffirmation of INCITS/ISO/IEC 17913:2000[2010]) INCITS/ISO/IEC :2005/COR 1:2009[2010] this is edition one of two editions that are being carried in both SC 37 and INCITS; this should be (reaffirmation of INCITS/ISO/IEC :2005/COR 1:2009 [2010]) INCITS/ISO/IEC :2007[2010] is listed as (reaffirmation of INCITS/ISO/IEC :2007 [2009]); should be (reaffirmation of INCITS/ISO/IEC :2009 [2010]) INCITS/ISO/IEC 10747:1994[2010] - scope in ANSI Standards Action is listed as Technical Corrigendum 1 and should be the base standard; this should be, This standard specifies a protocol to be used by boundary intermediate systems to acquire and maintain information for the purpose of routeing NPDUs between different routeing domains. Lays down the procedures for the exchange of inter-domain reachability and path information between BISs, the procedures for maintaining inter-domain routeing information bases within a BIS, the encoding of protocol data units used to distribute inter-domain routeing information between BISs, the functional requirements for implementations that claim conformance to this standard. The protocol described operates at the level of individual routeing domains. Does not cover the establishment of administrative domains. INCITS/ISO/IEC 2382:2015 [2015] is listed as ((identical national adoption of and revision of INCITS/ISO/IEC :1999 [R2014]); this should be (identical national adoption of and revision of INCITS/ISO/IEC :1993[R2013], -2:1976[R2013], -4:1999[R2014], -5:1999[R2014], - 7:2000[R2014], -9:1995[R2013], -10:1979[R2013], -12:1988[R2013], -13:1996[R2011], - 17:1999[2013], -20:1990[R2011], -23:1994[R2011], -24:1995[R2011], -25:1992[R2011], - 26:1993[R2011], -27:1994[R2011], -28:1995[R2011], -37:2012[2013], -22:1986[R2011], INCITS/ISO :1987[R2013], -6:1987[2010], -19:1989[S2011], -21:1985[S2011]

9 Standards Action - October 16, Page 9 of 43 Pages Call for Members (ANS Consensus Bodies) Directly and materially affected parties who are interested in participating as a member of an ANS consensus body for the standards listed below are requested to contact the sponsoring standards developer directly and in a timely manner. BHMA (Builders Hardware Manufacturers Association) Office: Phone: Fax: 355 Lexington Avenue 15th Floor New York, NY Emily Brochstein (212) (212) ebrochstein@kellencompany.com BSR/BHMA A x, Architectural Door Trim (revision of ANSI/BHMA A ) Obtain an electronic copy from: mtierney@kellencompany.com BSR/BHMA A x, Door Controls - Overhead Stops and Holders (revision of ANSI/BHMA A ) Obtain an electronic copy from: mtierney@kellencompany.com BSR/BHMA A x, Release Devices - Closer Holder, Electromagnetic and Electromechanical (revision of ANSI/BHMA A ) Obtain an electronic copy from: mtierney@kellencompany.com ECIA (Electronic Components Industry Association) Office: Phone: Fax: 2214 Rock Hill Road Suite 265 Herndon, VA Laura Donohoe (571) (571) ldonohoe@ecianow.org BSR/EIA x, Thermal Shock for Hermetic Electrical Connectors and Sockets (new standard) ISA (International Society of Automation) Office: Phone: Fax: 67 Alexander Drive Research Triangle Park, NC Eliana Brazda (919) (919) ebrazda@isa.org BSR/ISA x, Face-to-Centerline Dimensions for Flanged Globe-Style Angle Control Valve Bodies (Classes 150, 300, and 600) (revision of ANSI/ISA (R2007)) Obtain an electronic copy from: ebrazda@isa.org ITI (INCITS) (InterNational Committee for Information Technology Standards) Office: 1101 K Street NW Suite 610 Washington, DC Phone: Fax: Rachel Porter (202) comments@itic.org BSR/INCITS x, Information technology - Security Features for SCSI Commands (SFSC) (new standard) Obtain an electronic copy from: BSR/INCITS x, Information Technology - Fibre Channel - Switch Fabric - 6 (Fc-Sw-6) (new standard) Obtain an electronic copy from: BSR/INCITS x, Information technology - Fibre Channel - Physical Interfaces - 6P 128GFC Four Lane Parallel (FC-PI-6P) (new standard) Obtain an electronic copy from: NEMA (ASC C78) (National Electrical Manufacturers Association) Office: Phone: 1300 N 17th St Rosslyn, VA Michael Erbesfeld Michael.Erbesfeld@nema.org BSR C (R201x), High-Pressure Sodium Lamps (reaffirmation and redesignation of ANSI ANSLG C ) BSR C (R201x), Dimensions for Projection Lamps - Double- Contact, Medium Ring (Special B), Base-up Type (reaffirmation of ANSI C (R2009)) BSR C (R201x), High Intensity Discharge Lamps - Methods of Measuring Characteristics (reaffirmation of ANSI C (R2009)) BSR C (R201x), Characteristics of Subminiature Lamps of T1 and T1-3/4 Shapes (reaffirmation of ANSI C ) BSR C (R201x), Slide Projector Lamps, Condensing, Dichroic, 1.65-in. (42 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GX5.3 Bases (reaffirmation of ANSI C (R2009)) BSR C (R201x), Slide Projector Lamps, Condensing, Dichroic, Two-inch {51 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GV 5.3 Bases (reaffirmation of ANSI C (R2009))

10 Standards Action - October 16, Page 10 of 43 Pages BSR C (R201x), Discharge Lamps (Excluding Fluorescent Lamps) - Safety Specifications (reaffirmation and redesignation of ANSI/IEC C (R2009)) NEMA (ASC C82) (National Electrical Manufacturers Association) Office: Phone: 1300 N 17th St Rosslyn, VA Michael Erbesfeld Michael.Erbesfeld@nema.org BSR C X, Lamp Ballasts - Reference Ballasts for Fluorescent Lamps (revision of ANSI C (R2010)) NEMA (National Electrical Manufacturers Association) Office: Phone: Fax: 1300 North 17th Street Suite 900 Rosslyn, VA Michael Leibowitz (703) (703) mik_leibowitz@nema.org UL (Underwriters Laboratories, Inc.) Office: Phone: 12 Laboratory Drive Research Triangle Park, NC Casey Granata (919) Casey.Granata@UL.Com BSR/UL X, Standard for Safety for Attachment Plugs and Receptacles (Proposal dated ) (revision of ANSI/UL a) Obtain an electronic copy from: BSR/UL 773A-201x, Standard for Safety for Nonindustrial Photoelectric Switches for Lighting Control (revision of ANSI/UL 773A-2006 (R2011)) Obtain an electronic copy from: BSR/UL X, Reference Standard for Electrical Wires, Cables, and Flexible Cords (revision of ANSI/UL ) Obtain an electronic copy from: BSR/MW , Magnet Wire (revision and redesignation of ANSI/NEMA MW ) PLATO (Portable Lights American Trade Organization) Office: Phone: P.O. Box 107 Marblehead, MA Michael Tierney (440) mtierney@kellencompany.com BSR/PLATO FL 1-201x, Flashlight Basic Performance Standard (revision of ANSI/NEMA FL1-2009) Obtain an electronic copy from: mtierney@kellencompany.com TAPPI (Technical Association of the Pulp and Paper Industry) Office: Phone: Fax: 15 Technology Parkway South Peachtree Corners, GA Laurence Womack (770) (770) standards@tappi.org BSR/TAPPI T 476 om-2011 (R201x), Abrasion loss of paper and paperboard (Taber-type method) (reaffirmation and redesignation of ANSI/TAPPI T 476 om-2011) BSR/TAPPI T 578 sp-201x-2011 (R201x), Accelerated light aging of printing and writing paper by xenon-arc exposure apparatus (reaffirmation and redesignation of ANSI/TAPPI T 578 sp-2011)

11 Standards Action - October 16, Page 11 of 43 Pages Final Actions on American National Standards The standards actions listed below have been approved by the ANSI Board of Standards Review (BSR) or by an ANSI-Audited Designator, as applicable. ACCA (Air Conditioning Contractors of America) New Standard ANSI/ACCA 14 QMref-2015, Quality Maintenance of Commercial Refrigeration Systems (new standard): 10/14/2015 ASB (ASC Z50) (American Society of Baking) Revision ANSI/ASB Z , Bakery Equipment - Sanitation Standards (revision of ANSI ASB Z ): 10/12/2015 AWWA (American Water Works Association) Revision ANSI/AWWA B , Powdered Activated Carbon (revision of ANSI/AWWA B ): 10/12/2015 * BHMA (Builders Hardware Manufacturers Association) Revision ANSI/BHMA A , Cabinet Hardware (revision of ANSI/BHMA A ): 10/14/2015 MHI (Material Handling Industry) New Standard ANSI/MH , Specification for the Design, Testing and Utilization of Industrial Steel Cantilevered Storage Racks (new standard): 10/8/2015 MSS (Manufacturers Standardization Society) New Standard ANSI/MSS SP , Valves for Cryogenic Service, including Requirements for Body/Bonnet Extensions (new standard): 10/12/2015 ANSI/MSS SP , Pressure Seal Bonnet Valves (new standard): 10/12/2015 PLASA (PLASA North America) Withdrawal ANSI/PLASA E , Unidirectional Transport of IEEE 802 data frames over ANSI E1.11 (DMX512-A) (withdrawal of ANSI/PLASA E ): 10/8/2015 UL (Underwriters Laboratories, Inc.) New Standard ANSI/UL , Standard for Safety for Solar Trackers (new standard): 10/8/2015 ANSI/UL a, Standard for Safety for Solar Trackers (new standard): 10/8/2015 Reaffirmation ANSI/UL (R2015), Standard for Safety for Gas-Tube-Sign Cable (Proposal dated 8/21/15) (reaffirmation of ANSI/UL ): 10/8/2015 Revision ANSI/UL , Standard for Flat-Plate Photovoltaic Modules and Panels (revision of ANSI/UL ): 10/12/2015

12 Project Initiation Notification System (PINS) Standards Action - October 16, Page 12 of 43 Pages ANSI Procedures require notification of ANSI by ANSI-accredited standards developers (ASD) of the initiation and scope of activities expected to result in new or revised American National Standards (ANS). Early notification of activity intended to reaffirm or withdraw an ANS and in some instances a PINS related to a national adoption is optional. The mechanism by which such notification is given is referred to as the PINS process. For additional information, see clause 2.4 of the ANSI Essential Requirements: Due Process Requirements for American National Standards. Following is a list of proposed actions and new ANS that have been received recently from ASDs. Please also review the section in Standards Action entitled "American National Standards Maintained Under Continuous Maintenance" for additional or comparable information with regard to standards maintained under the continuous maintenance option. To view information about additional standards for which a PINS has been submitted and to search approved ANS, please visit which is a database of standards information. Note that this database is not exhaustive. Directly and materially affected interests wishing to receive more information or to submit comments are requested to contact the standards developer directly within 30 days of the publication of this announcement. ANS (American Nuclear Society) Office: Fax: 555 North Kensington Avenue La Grange Park, IL Kathryn Murdoch (708) kmurdoch@ans.org BSR/ANS x, Nuclear Criticality Safety Training for Fissionable Materials Operations Outside Reactors (revision of ANSI/ANS (R2015)) Stakeholders: USDOE, USDOE contractors, USNRC, USNRC licensees, universities, organizations engaged in manufacturing and handling of nuclear fuel, American Nuclear Insurers, and international counterparts. Project Need: A revised standard is needed to update the appropriate nuclear criticality safety training for fissionable materials operations outside nuclear reactors. This standard provides criteria for nuclear criticality safety training for operations with fissionable materials outside reactors. ASC X9 (Accredited Standards Committee X9, Incorporated) Office: Fax: 1212 West Street Suite 200 Annapolis, MD Janet Busch (410) janet.busch@x9.org BSR X x, Balance and Transaction Reporting Standard (BTRS) (Fomerly Cash Management Reporting Specification Version 2) (revision of ANSI X ) Stakeholders: Financial institutions, corporations, industry associations and vendors from financial institutions, stakeholders will include staff from their information reporting, product management and operations areas. The participants must be knowledgeable of existing reporting practices in the areas of wires, check, lock box, deposits, adjustments, ACH, concentration accounts, international transactions, messaging etc. Project Need: The Codes need to be updated and presented as a formal X9 standard. The BAI Codes Type 2 has been in use in the United States and elsewhere for a period of time. BAI has legally transferred the copyright to X9. These codes are widely used in the area of cash management reporting by banks and corporations. The project will convert the existing codes into a formal cash reporting standard and update all relevant areas. Given the widespread international use of the BAI codes, the final work product will consider the needs of a broader community, including ISO ASME (American Society of Mechanical Engineers) Office: Fax: Two Park Avenue New York, NY Mayra Santiago (212) ansibox@asme.org BSR/ASME MFC x, Measurement of Fluid Flow in Closed Conduits by Means of Coriolis Mass Flowmeters (revision and redesignation of ANSI/ASME MFC-11M-2006 (R2014)) Stakeholders: Manufacturers and users of Coriolis mass flowmeters. Project Need: Revised to reflect the state of the art. This Standard establishes common terminology, gives guidelines for the selection, installation, calibration, and operation of Coriolis flowmeters for the measurement of mass flow rate, density of fluids and determination of volume flow rate. The content of this Standard is applied to the flow measurement of liquids, gases, mixtures of gases, multiphase flows, and miscible and immiscible mixtures of liquids. AWWA (American Water Works Association) Office: Fax: 6666 W. Quincy Ave. Denver, CO Paul Olson (303) polson@awwa.org; vdavid@awwa.org BSR/AWWA C x, Fabricated Stainless Steel Slide Gates (revision of ANSI/AWWA C ) Stakeholders: Water supply and wastewater treatment industry, wastewater and water utilities, consulting engineers, water treatment equipment manufacturers. Project Need: To provide the minimum requirements for fabricated stainless-steel slide gates for water and wastewater service, including material, design, inspection, testing, and handling. This standard describes vertically mounted, fabricated, stainless-steel slide gates with full-aperture closure, designed for either seating head or unseating head or both, in ordinary water supply and wastewater service. The gates are primarily used to shut off or throttle water or wastewater flow through a rectangular or round orifice, end of channel, or in-channel opening.

13 Standards Action - October 16, Page 13 of 43 Pages BSR/AWWA C x, Fabricated Aluminum Slide Gates (revision of ANSI/AWWA C ) Stakeholders: Water supply and wastewater treatment industry, wastewater and water utilities, consulting engineers, water treatment equipment manufacturers. Project Need: To provide the minimum requirements for fabricated aluminum slide gates for water and wastewater service, including material, design, inspection, testing, and handling. This standard describes vertically mounted, fabricated, aluminum slide gates with full-aperture closure, designed for either seating head or unseating head or both, in ordinary water supply and wastewater service. The gates are primarily used to shut off or throttle water or wastewater flow through a rectangular or round orifice, end of channel, or in-channel opening. They may be of either conventional-closure or flush-bottom-closure type and may be opened upward or downward. BSR/AWWA C x, Fabricated Composite Slide Gates (revision of ANSI/AWWA C ) Stakeholders: Water supply and wastewater treatment industry, wastewater and water utilities, consulting engineers, water treatment equipment manufacturers. Project Need: To provide the minimum requirements for fabricated composite slide gates for water and wastewater service, including material, design, inspection, testing, and handling. This standard describes vertically mounted, fabricated, composite, resilient-seated slide gates with full-aperture closure, designed for either seating head or unseating head or both, in ordinary water supply and wastewater service. The gates are primarily used to shut off or throttle water and wastewater flow through a rectangular or round orifice, end of channel, or in-channel opening. They may be of either conventional-closure or flush-bottom-closure type and may be opened either upward or downward. BICSI (Building Industry Consulting Service International) Office: Fax: 8610 Hidden River Parkway Tampa, FL Jeff Silveira (813) jsilveira@bicsi.org BSR/BICSI X, Electronic Safety and Security (ESS) System Design and Implementation Best Practices (revision of ANSI/BICSI ) Stakeholders: ICT system designers, IT professionals, security industry professionals. Project Need: Updates to keep standard current with industry and system requirements and trends. This standard is written for use in the design and implementation of the structured cabling systems used within electronic safety and security systems. This standard provides a reference of common technology and design practices and is not intended to be used by architects and engineers as their sole reference or as a step-by-step design guide. This standard may also be used to determine design requirements in conjunction with the system owner, occupant, or safety and security consultant. BSR/BICSI X, Information Communication Technology Design and Implementation Practices for Intelligent Buildings and Premises (new standard) Stakeholders: ICT system designers, building system designers, IT professionals, building and facility managers. Project Need: With the increase of building systems requiring network capability to interact with other systems, there currently is not a standard focused on the infrastructure and integration of different systems onto a common ICT infrastructure. This standard will cover the design and implementation of the information communication technology systems required to support an intelligent building/premise integrated design. Systems that are expected to be covered, include, but are not limited to: building automation/management, utility utilization, lighting, signage and wayfinding, sound and acoustical services, location, and asset tracking. BSR/BICSI X, In-Building and Campus Wireless LAN Systems Design and Implementation Best Practices (new standard) Stakeholders: ICT designers, providers, installers; wireless system manufacturers, all industries utilizing style wireless communication protocols. Project Need: The public has come to assume WLAN coverage for their handheld devices will be available practically everywhere they go. This explosion in demand; multiple orders of magnitude increases in data rates; and systems increasingly crowding each other is pushing the limits of the technology. Systems must now be carefully designed and implemented by highly knowledgeable personnel using the latest test equipment to ensure a fully operational system that does not interfere with other networks. The standards includes material for the design and implantation of a inbuilding/campus wireless network (WLAN), including, but not limited to: Required infrastructure, distribution technology types, location technologies, compliance and legal issues. design coordination, wireless design, telecommunication infrastructure, installation & commissioning, specific locations and situations. BSR/BICSI X, Data Center Operations and Maintenance Best Practices (new standard) Stakeholders: Data-center managers; operation and maintenance engineers and technicians; ICT, electrical and mechanical contractors providing managed services. Project Need: Questions have arisen from data-center owners, their representatives, and other interested parties concerning standards (or the lack thereof) for data-center operations. At the current time, there are no approved and recognized open standards for data-center operations and maintenance within the United States. The scope of the project would be to develop operations and maintenance standards for data center managers, technicians, and contractors providing data-center managed services. The standard would also provide guidance for professionals responsible for maintaining the data-center ICT infrastructure, and also the facility infrastructure. ECIA (Electronic Components Industry Association) Office: Fax: 2214 Rock Hill Road Suite 265 Herndon, VA Laura Donohoe (571) ldonohoe@ecianow.org BSR/EIA x, Thermal Shock for Hermetic Electrical Connectors and Sockets (new standard) Stakeholders: Electrical, electronics, and telecommunication industry. Project Need: New standard. This standard is intended to develop test standards used in military standards not presently covered by an EIA-364 Test Procedure.

14 Standards Action - October 16, Page 14 of 43 Pages NEMA (ASC C119) (National Electrical Manufacturers Association) Office: Fax: 1300 North 17th Street Suite 900 Rosslyn, VA Paul Orr (703) Pau_orr@nema.org BSR C , Connectors for Use between Aluminum-to- Aluminum and Aluminum-to-Copper Conductors Designed for Normal Operation at or Below 93 C and Copper-to-Copper Conductors Designed for Normal Operation at or Below 100 C (revision of ANSI C ) Stakeholders: Electric utilities, connector manufacturers. Project Need: Project is to revise ANSI C119.4 to remove common tests that are now contained in the separate test document ANSI C This standard covers connectors used for making electrical connections between aluminum-to-aluminum or aluminum-to-copper or copper-to-copper conductors used on distribution and transmission lines for electric utilities. This standard establishes the electrical and mechanical test requirements for electrical connectors. Additional optional tests are shown in the annexes. This standard is not intended to recommend operating conditions or temperatures. NEMA (ASC C82) (National Electrical Manufacturers Association) Office: 1300 N 17th St Rosslyn, VA Michael Erbesfeld Michael.Erbesfeld@nema.org BSR C X, Lamp Ballasts - Reference Ballasts for Fluorescent Lamps (revision of ANSI C (R2010)) Stakeholders: Manufacturers, users, test labs, lighting specifiers. Project Need: This project is needed to align High Frequency reference ballast sections with most recent revisions of ANSI C and ANSI C82.11 This standard describes the essential design features and operating characteristics of reference ballasts for fluorescent lamps. The items specified are those that have been found necessary to ensure accurate and reproducible results when either lamps or ballasts are being tested. It includes requirements for both line-frequency and high-frequency circuits. The specific values of rated input voltage and impedance for each size of lamp are listed in the applicable ANSI C78 lamp standard. NEMA (National Electrical Manufacturers Association) Office: Fax: 1300 North 17th Street Suite 900 Rosslyn, VA Michael Leibowitz (703) mik_leibowitz@nema.org BSR/MW , Magnet Wire (revision and redesignation of ANSI/NEMA MW ) Stakeholders: Revisions to be proposed are necessary to have dimensional requirements for rectangular wire to encourage standard requirements and to introduce new specifications for class 120 polyvinyl acetal enamelled wire. Project Need: To revise MW MW 1000 presents in concise and convenient form all existing NEMA standards for round, rectangular, and square film-insulated and/or fibrous-covered copper and aluminum magnet wire for use in electrical apparatus. Included are the definitions, type designations, dimensions, constructions, performance, and test methods for magnet wire generally used in the winding of coils for electrical apparatus. TAPPI (Technical Association of the Pulp and Paper Industry) Office: Fax: 15 Technology Parkway South Peachtree Corners, GA Laurence Womack (770) standards@tappi.org BSR/TAPPI T 476 om-2011 (R201x), Abrasion loss of paper and paperboard (Taber-type method) (reaffirmation and redesignation of ANSI/TAPPI T 476 om-2011) Stakeholders: Manufacturers of pulp, paper, packaging, or related products; consumers or converters of such products; and suppliers of equipment, supplies, or raw materials for the manufacture of such products. Project Need: To conduct required five-year review of an existing TAPPI/ANSI standard in order to revise if needed to address new technology or correct errors. This method determines the resistance of surfaces of paper and paperboard to the action of abrasion, either wet or dry, by measuring abrasion loss. This test is not applicable to the surfaces treated with wax or similar materials which would fill in the pores of the abrasive wheels. BSR/TAPPI T 578 sp-201x-2011 (R201x), Accelerated light aging of printing and writing paper by xenon-arc exposure apparatus (reaffirmation and redesignation of ANSI/TAPPI T 578 sp-2011) Stakeholders: Manufacturers of pulp, paper, packaging, or related products; consumers or converters of such products; and suppliers of equipment, supplies, or raw materials for the manufacture of such products. Project Need: To conduct required five-year review of an existing TAPPI/ANSI standard in order to revise if needed to address new technology or correct errors. This standard practice describes a laboratory procedure for the exposure of printing and writing paper to xenon-arc light at elevated levels of light flux to permit accelerated aging of that type of paper. This standard practice specifies the sample preparation and conditions of exposure required to obtain information on the relative stability of paper with regard to change in optical properties brought about by exposure of such paper to light. UL (Underwriters Laboratories, Inc.) Office: Fax: 12 Laboratory Dr. Research Triangle Park, NC Nicolette Allen (919) Nicolette.Allen@ul.com BSR/UL X, Standard for Safety for Air Dispersion System Materials (new standard) Stakeholders: Manufacturers and users of air-dispersion system materials. Project Need: To obtain national recognition of a standard covering airdispersion system materials. These requirements apply to air dispersion system materials for use in accordance with the following Codes: Installation of Air-Conditioning and Ventilating Systems, NFPA No. 90A; Installation of Warm Air Heating and Air-Conditioning Systems, NFPA No. 90B; International Mechanical Code (IMC); and CBO Uniform Mechanical Code (UMC). These requirements include preformed lengths of fabric or non-fabric products intended to convey and distribute air. They are intended to be limited for use in air handling systems in exposed locations operating under positive pressure. These do not address the joints between sections of air dispersion system materials or end connections

15 Standards Action - October 16, Page 15 of 43 Pages UL (Underwriters Laboratories, Inc.) Office: Fax: 12 Laboratory Drive Research Triangle Park, NC Valara Davis (919) Valara.Davis@ul.com BSR/UL 1008R-201X, Standard for Refurbished Transfer Switch Equipment (new standard) Stakeholders: Manufacturers of transfer switches, consumers, retailers, electrical inspectors, electricians, electrician labor unions, building owners, fire department personnel. Project Need: There are currently no nationally recognized requirements for refurbished transfer switches. Refurbished equipment needs to be evaluated for safety. This standard applies to refurbished automatic transfer switches; manual or non-automatic transfer switches; closed transition transfer switches; hybrid transfer switches; transfer switches for fire pumps; bypass/isolating switches; softload transfer switches; transfer switches intended for use as service equipment; and branch circuit emergency lighting transfer switches (BCELTS), that have a maximum rating of 1000 volts for use in non-hazardous locations.

16 Standards Action - October 16, Page 16 of 43 Pages American National Standards Maintained Under Continuous Maintenance The ANSI Essential Requirements: Due Process Requirements for American National Standards provides two options for the maintenance of American National Standards (ANS): periodic maintenance (see clause 4.7.1) and continuous maintenance (see clause 4.7.2). Continuous maintenance is defined as follows: The standard shall be maintained by an accredited standards developer. A documented program for periodic publication of revisions shall be established by the standards developer. Processing of these revisions shall be in accordance with these procedures. The published standard shall include a clear statement of the intent to consider requests for change and information on the submittal of such requests. Procedures shall be established for timely, documented consensus action on each request for change and no portion of the standard shall be excluded from the revision process. In the event that no revisions are issued for a period of four years, action to reaffirm or withdraw the standard shall be taken in accordance with the procedures contained in the ANSI Essential Requirements. The Executive Standards Council (ExSC) has determined that for standards maintained under the Continuous Maintenance option, separate PINS announcements are not required. The following ANSI Accredited Standards Developers have formally registered standards under the Continuous Maintenance option. - AAMI (Association for the Advancement of Medical Instrumentation) - AAMVA (American Association of Motor Vehicle Administrators) - AGA (American Gas Association) - AGSC (Auto Glass Safety Council) - ASC X9 (Accredited Standards Committee X9, Incorporated) - ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) - ASME (American Society of Mechanical Engineers) - ASTM (ASTM International) - GBI (The Green Building Initiative) - GEIA (Greenguard Environmental Institute) - HL7 (Health Level Seven) - IESNA (The Illuminating Engineering Society of North America) - MHI (ASC MH10) (Material Handling Industry) - NAHBRC (NAHB Research Center, Inc.) - NBBPVI (National Board of Boiler and Pressure Vessel Inspectors) - NCPDP (National Council for Prescription Drug Programs) - NISO (National Information Standards Organization) - NSF (NSF International) - PRCA (Professional Ropes Course Association) - RESNET (Residential Energy Services Network) - TIA (Telecommunications Industry Association) - UL (Underwriters Laboratories, Inc.) To obtain additional information with regard to these standards, including contact information at the ANSI Accredited Standards Developer, please visit ANSI Online at select Standards Activities, click on Public Review and Comment and American National Standards Maintained Under Continuous Maintenance. This information is also available directly at Alternatively, you may contact the Procedures & Standards Administration department (PSA) at psa@ansi.org or via fax at If you request that information be provided via , please include your address; if you request that information be provided via fax, please include your fax number. Thank you.

17 Standards Action - October 16, Page 17 of 43 Pages ANSI-Accredited Standards Developers Contact Information The addresses listed in this section are to be used in conjunction with standards listed in PINS, Call for Comment and Final Actions. This section is a list of developers who have submitted standards for this issue of Standards Action it is not intended to be a list of all ANSI-Accredited Standards Developers. Please send all address corrections to Standards Action Editor at standact@ansi.org. AAMI Association for the Advancement of Medical Instrumentation 4301 N Fairfax Drive Suite 301 Arlington, VA Phone: (703) Web: ACCA Air Conditioning Contractors of America 2800 Shirlington Road Suite 300 Arlington, VA Phone: (703) Web: ANS American Nuclear Society 555 North Kensington Avenue La Grange Park, IL Phone: (708) Fax: (708) Web: ASABE American Society of Agricultural and Biological Engineers 2950 Niles Road St Joseph, MI Phone: (269) Fax: (269) Web: ASB (ASC Z50) American Society of Baking 243 Reade Drive Cogan Station, PA Phone: (570) Fax: (570) Web: ASC X9 Accredited Standards Committee X9, Incorporated 1212 West Street Suite 200 Annapolis, MD Phone: (410) Fax: (410) Web: ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc Tullie Circle, NE Atlanta, GA Phone: (678) Fax: (678) Web: ASME American Society of Mechanical Engineers Two Park Avenue New York, NY Phone: (212) Fax: (212) Web: AWWA American Water Works Association 6666 W. Quincy Ave. Denver, CO Phone: (303) Fax: (303) Web: BHMA Builders Hardware Manufacturers Association 355 Lexington Avenue 15th Floor New York, NY Phone: (212) Fax: (212) Web: BICSI Building Industry Consulting Service International 8610 Hidden River Parkway Tampa, FL Phone: (813) Fax: (813) Web: CSA CSA Group 8501 East Pleasant Valley Rd. Cleveland, OH Phone: (216) x88321 Fax: (216) Web: ECIA Electronic Components Industry Association 2214 Rock Hill Road Suite 265 Herndon, VA Phone: (571) Fax: (571) Web: ISA (Organization) International Society of Automation 67 Alexander Drive Research Triangle Park, NC Phone: (919) Fax: (919) Web: ITI (INCITS) InterNational Committee for Information Technology Standards 1101 K Street NW Suite 610 Washington, DC Phone: (202) Fax: Web: MHI Material Handling Industry 8720 Red Oak Blvd. - Ste. 201 Suite 201 Charlotte, NC Phone: (704) Fax: (704) Web: MSS Manufacturers Standardization Society 127 Park Street, NE Vienna, VA Phone: (703) Fax: (703) Web: NASBLA National Association of State Boating Law Administrators 1648 McGrathiana Parkway Suite 360 Lexington, KY Phone: (859) Web: NEMA (ASC C12) National Electrical Manufacturers Association 1300 North 17th Street Suite 900 Rosslyn, VA Phone: (703) Fax: (703) Web: NEMA (ASC C78) National Electrical Manufacturers Association 1300 N 17th St Rosslyn, VA Phone: Web: NEMA (Canvass) National Electrical Manufacturers Association 1300 North 17th Street Suite 900 Rosslyn, VA Phone: (703) Fax: (703) Web: PLASA PLASA North America 630 Ninth Avenue Suite 609 New York, NY Phone: (212) Fax: (212) Web: PLATO Portable Lights American Trade Organization P.O. Box 107 Marblehead, MA Phone: (440) Web: SPRI Single Ply Roofing Institute 411 Waverley Oaks Road Suite 331B Waltham, MA Phone: (781) Fax: (781) Web: TAPPI Technical Association of the Pulp and Paper Industry 15 Technology Parkway South Peachtree Corners, GA Phone: (770) Fax: (770) Web: UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL Phone: (847) Web:

18 Standards Action - October 16, Page 18 of 43 Pages ISO & IEC Draft International Standards This section lists proposed standards that the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC) are considering for approval. The proposals have received substantial support within the technical committees or subcommittees that developed them and are now being circulated to ISO and IEC members for comment and vote. Standards Action readers interested in reviewing and commenting on these documents should order copies from ANSI. Comments Comments regarding ISO documents should be sent to ANSI s ISO Team (isot@ansi.org); those regarding IEC documents should be sent to Charles T. Zegers, General Secretary of the USNC (czegers@ansi. org). The final date for offering comments is listed after each draft. Ordering Instructions ISO and IEC Drafts can be made available by contacting ANSI s Customer Service department. Please your request for an ISO or IEC Draft to Customer Service at sales@ansi.org. When making your request, please provide the date of the Standards Action issue in which the draft document you are requesting appears. ISO Standards AGRICULTURAL FOOD PRODUCTS (TC 34) ISO/DIS 18862, Analysis of coffee and coffee products - Determination of acrylamide - Methods using HPLC-MS/MS and GC-MS after derivatisation - 11/7/2015, $77.00 AIR QUALITY (TC 146) ISO/DIS 20581, Workplace air - General requirements for the performance of procedures for the measurement of chemical agents - 1/10/2016, $77.00 AIRCRAFT AND SPACE VEHICLES (TC 20) ISO/DIS 17770, Space systems - Cube satellites (CubeSats) - 1/9/2016, $58.00 ISO/DIS 21076, Space data and information transfer systems - Space communications cross support - Architecture requirements document (based on CCSDS M-1) - 1/9/2016, $ ISO/DIS 21077, Space data and information transfer systems - Digital motion imagery (based on CCSDS B-1) - 1/16/2016 ISO/DIS 21080, Space data and information transfer systems - Licklider transmission protocol (LTP) for CCSDS (based on CCSDS B-1) - 1/9/2016 ISO/DIS 21082, Mission operations - Mal space packet transport binding and binary encoding - 1/9/2016, $ DENTISTRY (TC 106) ISO/DIS , Dentistry - Laboratory cutters - Part 3: Tungsten carbide cutters for milling machines - 1/16/2016, $33.00 FREIGHT CONTAINERS (TC 104) ISO/DIS 1161, Series 1 freight containers - Corner and intermediate fittings - Specification - 11/7/2015, $82.00 MATERIALS, EQUIPMENT AND OFFSHORE STRUCTURES FOR PETROLEUM AND NATURAL GAS INDUSTRIES (TC 67) ISO/DIS , Offshore containers and associated lifting sets - Part 2: Lifting sets - Design, manufacture and marking - 1/9/2016, $58.00 ISO/DIS , Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 3: Floating unit - 1/10/2016, $93.00 MECHANICAL CONTRACEPTIVES (TC 157) ISO/DIS 19671, Additional Lubricants for Condoms - Effect on Condom Strength - 11/8/2015, $46.00 ROAD VEHICLES (TC 22) ISO 16380/DAmd1, Road vehicles - Blended fuels refuelling connector - Amendment 1-1/14/2016, FREE ISO/DIS 2698, Diesel engines - Clamp-mounted fuel injectors, types 7 and 28-11/7/2015, $40.00 ISO/DIS 2974, Diesel engines - 60 degree female cones for highpressure fuel injection components - 11/8/2015, $58.00 ISO/DIS , Road vehicles - Controller area network (CAN) - Part 2: High-speed medium access unit - 1/16/2016, $93.00 ISO/DIS , Diesel engines - Fuel injection pumps and fuel injector low-pressure connections - Part 2: Non-threaded (push-on) connections - 11/8/2015, $58.00 SOLID BIOFUELS (TC 238) ISO/DIS 14780, Solid biofuels - Sample preparation - 3/18/2016, $88.00 TRANSPORT INFORMATION AND CONTROL SYSTEMS (TC 204) ISO/DIS 19079, Intelligent Transport Systems - Communications access for land mobiles (CALM) - 6LoWPAN networking - 11/8/2015, $93.00 ISO/DIS 19080, Intelligent Transport Systems - Communications access for land mobiles (CALM) - CoAP facility - 11/7/2015, $71.00 ISO/IEC JTC 1, Information Technology ISO/IEC DIS 20919, Information technology - Linear tape file system (LTFS) format specification - 11/8/2015, $ ISO/IEC DIS 20922, Information technology - Message Queuing Telemetry Transport (MQTT) v /8/2015, $ ISO/IEC DIS , Information technology - Multimedia service platform technologies - Part 2: MPEG extensible middleware (MXM) API - 11/6/2015, $112.00