CYNEMA SOUNDFIELD '~ SOUNDBAR SYSTEM BLENDING HIGH FIDELITY AND ARCHITECTURE

Transcription

1 CYNEMA SOUNDFIELD '~ SOUNDBAR SYSTEM BLENDING HIGH FIDELITY AND ARCHITECTURE

2 CONGRATULATIONS I Thank you for choosing Niles Cynema Soundfield, a unique and powerful solution for modern installations. Like all Niles products, Cynema Soundfield is built to the highest standards of quality and reliability. With proper installation and operation, you will experience years of high-performance, trouble-free use. For information on the complete line of innovative Niles products, please visit us at: TABLE OF CONTENTS INTRODUCTION 4 FEATURES AND BENEFITS 5 SPECIFICATIONS 6 PARTS GUIDE 7 INSTALLATION CONSIDERATIONS 9 INSTALLING THE SYSTEM 15 SYSTEM APPLICATIONS 24 OPERATION POWERED SYSTEMS 28 OPERATION PASSIVE SYSTEMS 31 WARRANTY

3 I CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus. 16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. 17. The power supply cord (sometimes referred to as the "Mains Plug") is used as the disconnect device and shall remain accessible and operable at all times. 18. Do not expose batteries to excessive heat such as sunshine, fire or the like. 19. Open flame sources, such as lighted candles, should NOT be placed on the apparatus. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. A The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. FCC Required Text: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate, radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/tv technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NILES AUDIO CORPORATION BUY-HIFI

4 INTRODUCTION Cynema Soundfield delivers both unobtrusive appearance and high performance. We created the new term Cynema Soundfield to describe the system because it is more than just a soundbar or a collection of independent speakers. Much more versatile than a traditional soundbar, speakers can be placed in a variety of configurations to optimize audio performance. Aesthetically, the Cynema Soundfield's virtually flat appearance complements the latest flat panel displays perfectly. Its unique in-wall mounting system dramatically improves the ease of installation and contributes to dynamic audio reproduction. Thin flat panel televisions must use thin speakers. Thin speakers fall short of our standards for high fidelity. Niles Cynema Soundfield is the solution that brings the aspects people appreciate most about flat panel TVs, unobtrusive appearance and high performance, to the world of installed audio products. : ~~~~).1 """"'""' I ~~~ ; CSF-~5 J

5 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS FEATURES AND BENEFITS SUPERIOR SOUND TO TYPICAL SOUNDBARS AND VASTLY SUPERIOR TO THE SPEAKERS BUILT INTO FLAT PANELS The Cynema Soundfield system is designed to utilize enclosures built into component speaker modules that tuck down and into the wall for outstanding performance in any wall environment. In powered models, a fully optimized, 30W x 3 Channel Amplifier Module with Dolby Digital processing powers the system's LCR speakers that feature a D'Appolito array configuration. UNOBTRUSIVE APPEARANCE Magnetically attached MicroPerf grill provides a low profile aesthetic look. The grille is paintable and adds more positioning flexibility during installation. EASY 'fo INSTALL The flexible and unique In-wall Mounting System makes for a straight forward install (no cutting of studs, wiring runs through rail system), and you can hang components while waiting for final placement. You can configure the mounting positions of each speaker module and the amplifier around existing studs with ease. NO HIGH VOLTAGE WIRING IN THE WALL DC power supply mounted separately sends low voltage DC power through wall to amplifier module allowing for wiring without the need for an electrician. OPTIMAL SPEAKER PLACEMENT Mounting System allows for ideal placement of LCR speakers in any existing stud configuration. SEAMLESS, SIMPLE OPERATION FOR END.USER System's Amplifier Module can learn remote functions for seamless integration. Amplifier auto-senses input and functions as seamless extension of TV control. COMPATIBLE WITH THE NILES WIRELESS SUBWOOFER SYSTEM (SW-T & SW-R) Easily connect a wireless SW-T and send audio signals wirelessly to any subwoofer equipped with an SW-R Wireless Receiver. VERSATILE APPLICATIONS The-cynema Soundfield Powered System incorporates versatile design features that enable it to work seamlessly as part of a Whole House Distributed Audio System. Simply connect a Distributed Audio System and it is automatically selected while the TV is powered OFF and the Djstributed Audio is ON. TV sound always takes priority when the TV is turned ON, even while the Whole House Audio is ON, greatly simplifying user operation. NILES AUDIO CORPORATION BUY-HIFI

6 SPECIFICATIONS LOUDSPEAKER MODULE SPEC DESCRIPTION Overall Dimension 9-5/8" L x 4" D x 6-1 /2" H (24.4cm L x 1 0.2cm D x 16.5cm H) Wiring Impedance- Nominal 60 Sensitivity Max SPL Frequency Response Power Handling Capability 86 db, 1kHz@ 1W/1 m 105dB (LCR system) 65Hz- 25kHz 100 Watts AMPLIFIER MODULE PART NO. CSFAMP (FOR MODELS CSF48A, CSF55A, AND CSF65A) SPEC DESCRIPTION Output Power 30W RMS x 3 Frequency response Channel Separation Signal to Noise: 1OOHz to 20kHz, +0dB/-3dB or better (channel to channel 1kHz > 70dB or better 1OOHz to 20kHz un-weighted > 75dB or better based on Rated Power POWER SUPPLY (FOR MODELS CSF48A, CSF55A, AND CSF65A) SPEC AC Input DC Output DESCRIPTION V-2.5A, 50-60Hz 24V = 5A Max. & 120W Max. BOX CONTENTS: All Models (3) Speaker Modules (1) In-Wall Mounting System with Grille (1) Cutout Template for In-Wall Mounting System (1) Warranty Card Powered Models Only (1) Amplifier Module (1) In-Wall Power Supply Box with AC power cord (1) Cutout Template for In-Wall Power Supply Box (1) Niles SWT Bracket (1) Toslink Optical Cable 3m (1) Stereo 3.5mm to dual RCA Cable (1) DC power cable for wireless transmitter 1.5m (3) Speaker Wires for Left, Center, and Right

7 CYNEMA SOUNDFIELDTM SOUNDBAR SYSTEMS SYSTEM PARTS GUIDE SPEAKER FRONT VIEW SPEAKER REAR VIEW Gold Plated Binding Posts AMPLIFIER FRONT VIEW Rear Wave Enclosure "L'' Hanging Bracket CYNEMA'" (-;;::-::_:;-\ " !-----#--, ""' -~':::~/ c::::j c:::j 1! J ~---.. Power LED Indicator L..fi---- Status LED Indicator L...ft Source LED Indicator L---f Source Input Selector L !---- Master Volume Control Master Power Switch.. Audio Mute ' Remote Control Sensor r++---tt----- UC/R Channel Balance Control AMPLIFIER REAR VIEW ~=:;:...=~ UC/R Speaker Output Amplifier Power 24V DC Subwoofer Output Toslink Optical Input r Stereo Input ~ Subwoofer Transmitter Power 0<5V...-H Aux Stereo Input -~~ :.;~+--~!!.!!..--r-ttt-t---- HDMI Output (Pass-through) ~, HDMIInput ~:::::::rr -!:''' '''"'''= ":'''' " ''''''' '1'''':::::.~~~~ External IR Receiver Input NILES AUDIO CORPORATION BUY HIFI

8 SYSTEM PARTS GUIDE CONTINUED... IN-WALL POWER SUPPLY BOX (POWERED MODELS) Removable IEC Power Cord V AC, 50/60Hz 24V DC Power Cable Mounting Clamps IN-WALL MOUNTING SYSTEM AND GRILL Niles SW-T Bracket (For powered models only, optional wireless subwoofer system from Niles) In-Between Cover IJ In-Between Joiner ~ClampDown lj End Bracket Screw Down Slide Bracket

9 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLATION CONSIDERATIONS RECOMMENDED TOOLS FOR INSTALLATION: Cordless screwdriver Level One inch #2 Phillips tip Measuring tape 1/8" Drill bit Drop cloth Stud finder Painters tape Drywall saw. Spackle Small Slotted Screw Driver Rubber gloves Fish Tape Push/Pull Rod Cable ties Wire stripper 12" -14" Coat hanger wire Pencil SPEAKER WIRE Three 2 conductor 18 gauge speaker wires are included with all powered models (CSF48A, CSF55A and CSF65A) to connect the amplifier module to the three speaker modules. The passive model (CSF48P) requires a two-conductor wire of sufficient gauge for each of the three speaker modules. The actual gauge required depends on the length of the wire. For recommendations, please refer to the chart below: LENGTH OF WIRE FROM SPEAKER TO AMPLIFIER WIRE GAUGE Less Then 80 Feet Feet 16 More than 200 feet 14 When running loudspeaker wire inside walls or ceilings, use special jacketed cable (CL -2 or CL -3 rating) to protect the wire and to provide fire prevention. In some municipalities, conduit is required. For a trouble-free installation, low voltage wire such as loudspeaker wire must be in accordance with the National Electrical Code and any applicable provisions of the local building code. If you are unsure of the correct installation techniques, wire jacket, or type of conduit to use, consult a professional audio/video installer, building contractor, or the local building and inspection department. NILES AUDIO CORPORATION BUY HIFI

10 INSTALLATION CONSIDERATIONS CONTINUED... IN-WALL MOUNTING SYSTEM Note: Be very careful when locating the IN-WALL MOUNTING SYSTEM. Verify all locations behind the wall are clear of obstructions before cutting into the drywall. The speaker mounting system requires a rectangular opening in the drywall. See below for dimensions: MODEL CUTOUT DIMENSIONS ( H x W ) /; CSF48P 3-3/4" X 45-1/4" CSF48A 3-3/4 11 X 45-1/4 11 CSF55A 3-3/4" X 52-1/4" CSF65A 3-3/4" X 62-1/4 11 A minimum of 3-1 /2" depth inside the wall, when measured from the interior face of the drywall, plus 3" of clearance inside the wall below the top edge of the bottom mounting rail is required for proper clearance of the Speaker Module's Rear Wave Control enclosure 3" (7.6cm) IN-WALL MOUNTING SYSTEM The Cynema Soundfield's In-wall Mountirl{) System is uniquely designed to install as a single unit across multiple 16" centered wall studs while being located below, and centered with, a wall mounted flat panel TV. Figure 1: 55" Wall Mounting System centered below a TV and shown with Grille '( Grille

11 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLATION CONSIDERATIONS CONTINUED... IN-WALL MOUNTING SYSTEM Screw down slide brackets and clamp down end brackets enable proper installation of the movable speaker and amplifier modules in most installations regardless of the TV's relative position to the wall studs (see page 12 for installation exceptions that are affected by the relative position of the wall studs). Figure 2: 55" Wall Mounting System centered below a TV and shown without Grille Studs ~H-i Hioi Screw Down Brackets Clamp Down End Bracket MODEL CSF48P CSF48A CSF55A CSF65A GRILLE DIMENSIONS ( H x W ) 5-1/4 11 X /4 11 x /4 11 X /4 11 X NILES AUDIO CORPORATION BUY-HIFI

12 NILES Centerline I INSTALLATION CONSIDERATIONS CONTINUED... IMPORTANT INSTALLATION CONSIDERATION FOR 48" AND 55" MODELS: When installing the 48" model the TV's center must be at least 3 3/4" to the right or left of the wall stud center. When installing the 55" model the TV's center must be at least 1 /4" to the right or left of the wall stud. This allows for proper installation of all three speaker modules into the In-Wall Mounting System. (See Figure 3 & 4) The 65" model does not require this consideration due to its larger size. Figure 3: 48" System with the TV center 3 3/4" from the center of a wall stud Minimum Offset from Stud's Centerline \ TV relative to Flatpanel's Centerline and still I. I being able to center Grille with Flatpanel... I /4" -1 Figure 4: 55" System with the TV center 1/4" from the center of the a stud -~ e 1V Centerline i I II l f--- 1/4" I I I 1 - Minimum Offset from Stud's Centerline relative to Flatpanel's Centerline and still being able to center Grille with Flatpanel I II I II I ~ ~ m~ e ~ [J I e l :rm~!j ~ 1~"-~~!J 0::. * ~ (!) I L i _:rg_!j l I I I

13 CYNEMA SOUNDFIELDT~ SOUNDBAR SYSTEMS INSTALLATION CONSIDERATIONS CONTINUED... IN-WALL MOUNTING SYSTEM The Cynema Soundfield In-Wall Mounting System includes two rails that are connected together using up to four Screw Down Slide Brackets as shown in Figure 2 on page 11. There will be installations where the right and left end of the rails do not fall directly on a stud. Two Clamp Down End Brackets are included to secure rail ends that fall 3 or more inches from the nearest Screw Down Sliding Bracket by clamping the drywall as shown in Figure 2 on page 11. SPECIAL INSTALLATION NOTE: In some installations the ends of the top and bottom rails will fall too close to the side of a stud to provide the Clamp Down End Bracket with enough drywall for clamping and, at the same time, not fall close enough to the stud to use the Screw Down Sliding Bracket (Figure 5, A.). When this occurs, attach a wood furring strip flush on the side of that stud (Figure 5, B.) and use the Screw Down Slide Brackets screwed into these furring strips to secure the ends of the rails (Figure 5, C.). Figure 5: Stud with a furring strip and Screw Down Sliding Bracket v - T J A...t::;...>.. T "'\;}'\_ B '- L J ~ 1 $ T c f1 '-::::::::::.. $ I~ ~ NILES AUDIO CORPORATION BUY-HIFI

14 INSTALLATION CONSIDERATIONS CONTINUED... IN-WALL POWER SUPPLY BOX (POWERED MODELS ONLY) All Powered Cynema Soundfield models (CSF48A, CSF55A and CSF65A) include one In-Wall Power Supply Box. The In-Wall Power Supply Box incorporates the Amplifier Module power supply in a flush mounted electrical box. It includes a removable AC power cord on the front face plate, outside the wall, that plugs into a standard AC wall outlet. A 24V DC cable on the rear side, inside the wall, connects to the Amplifier Module that installs in the In-Wall Mounting System with the Speaker Modules. The In-Wall Power Supply Box is installed below or directly behind a wall mounted TV next to an AC outlet (Figure 6 A, B). Figure 6: In-Wall Power Supply Box J loy I~ A: Located Below the TV B: Located Behind the TV IMPORTANT INSTALLTION NOTE: Because the 24V DC cable provided is limited in length and cannot be spliced or extended, you must locate the In-Wall Power Supply Box as close as possible to the Amplifier Module. In some municipalities, conduit is required. For a trouble-free installation, low voltage wire must be in accordance with the National Electrical Code and any applicable provisions of the local building code. If you ore unsure of the correct installation techniques, wire jacket, or type of conduit to use, consult a professional audio/video installer, building contractor, or the local building and inspection department

15 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLING THE SYSTEM Niles Cynema Soundfield Speaker Systems are designed for installation in existing walls built using standard construction (drywall attached to wood studs spaced 16" on center). NOTE: Walls constructed with studs that are not accurately spaced 16" on center may prevent proper installation of the three Speaker Modules and the Amplifier Module. Install the included In-Wall Mounting System below and centered with a wall mounted Flat Panel TV. Wall cutout templates are supplied to mark the drywall and cut the proper size rectangular holes which accommodate the Cynema Soundfield In-Wall Mounting System and In-Wall Power Supply Box. Use the outside dimensions of the included Speaker Grille to determine the final location of the Cynema Soundfield Speaker System (see Page 11 Figure 2 for dimensions). The design of the magnetically attached Speaker Grill provides plus or minus 1" of left and right fine position adjustment after it is attached to the In-Wall Mounting System for precise center alignment with the TV. NOTE: Create o rough sketch that diagrams the exact position of the wall studs, TV and proposed speaker location to identify any unforeseen installation issues before cutting the drywall (see Page 12 Figure 3 & 4 ). CUT THE DRY WALL OPENING FOR THE IN-WALL MOUNTING SYSTEM (ALL MODELS) 1. Locate all of the studs in the wall below the lv location using a stud sensor or by hand-knocking. 2. Drill a 1/8" pilot hole just barely through the wallboard or dry wall (1/2" to 5/8" deep in most homes) in the vertical center of your proposed speaker location and the horizontal center of each stud bay the mounting system will cover. NOTE: BE VERY CAREFUL NOT TO DRILL THROUGH EXISTING WIRES, PIPES, OR STRUCTURE. IF YOU FEEL ANY EXTRA RESISTANCE AS YOU ARE DRILLING, STOP. 3. Cut a piece of coat hanger equal to the width of the stud bays. Bend the wire in half creating a right angle. Poke the "L shaped" wire into the pilot hole and turn it in a complete circle. If it turns freely in all directions, repeat the procedure for each stud bay of your proposed speaker location (See below). If the coat hanger wire movement is obstructed by a pipe or cable, fill the hole(s) with spackle or other patching compound and consider a different location. 4. Once you have determined the correct position for the speaker grille, center the supplied In-Wall Mounting System cutout template vertically and horizontally with the proposed grill location. Tape it to the wall surface making sure it is level with the lv and trace it using a pencil. Drill the four corners of the trace with a 1 /4" drill bit. 5.1f you are cutting a painted or wall papered drywall, use a sheetrock or keyhole saw. NOTE: BE VERY CAREFUL NOT TO SAW THROUGH EXISTING WIRES, PIPES, OR STRUCTURE. IF YOU FEEL ANY EXTRA RESISTANCE AS YOU ARE CUTTING, STOP. NILES AUDIO CORPORATION BUY-HIFI

16 INSTALLING THE SYSTEM CONTINUED... INSTALL THE IN-WALL POWER SUPPLY BOX (POWERED MODELS ONLY) 1. Choose a location to install the In-Wall Mount Power Supply that is either behind or below the TV and adjacent to an existing AC outlet (page 14 Figure 6), Perform the steps listed on page 15 at the proposed power supply location. Use the supplied In-Wall Power Supply Box cutout template to mark the wall for cutting if there are no obstructions found. Power Supply Cutout Dimensions (HxW): 3-11 /16" X 8-3/8" 9.4cm x 21.3cm 2. Route the 24V AC power wire on the rear of the power supply into this wall cutout and then out of the wall at the speaker cutout location. 3. Fold in each of the four mounting clamps and insert the Power Supply Box into the wall cutout. Tighten each of the four wall clamp screws inside the front edge of the power supply box to secure it in the wall. DO NOT OVERTIGHTEN. 4. Screw the supplied finish faceplate on to the In-Wall Power Supply Box. Important: Do not plug in the AC power cord until all other system connections are complete. ASSEMBLE AND INSTALL THE IN-WALL MOUNTING SYSTEM (ALL MODELS) 1. Determine the number of Screw Down Slide Brackets needed for In-Wall Mounting System by counting the number of wall studs that are exposed within the drywall cutout. 2. Slide the Screw Down Slide Brackets onto the Top and Bottom Rails as shown in Figure 7 and position them to align with the exposed wall studs within the drywall cutout. 3. Insert a Clamp Down End Bracket, as shown in Figure 7, on the ends of the Mounting Rails that fall more than 3" from a Screw Down Slide Bracket. See page 13 Figure 5 when the left or the right end of the Mounting Rail falls too close to the side of a wall stud to provide the Clamp Down End Bracket with enough drywall for clamping. Figure 7: In-Wall Mounting System 4. Align with and place the assembled In-Wall Mounting System into the wall cutout and loosely screw the Screw Down Slide Brackets to the wall studs with the screws provided. Final tightening of these screws will occur later in the installation procedure. Clamp Down End Bracket Screw Down Slide Bracket

17 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLING THE SYSTEM CONTINUED... INSTALL WIRES (PASSIVE MODELS) Speaker Wires: Route (3) two conductor speaker wires from the AV receiver into the wall and then to each speaker location utilizing the space between the Screw Down Slide Brackets and the wall stud to route the wire from one stud bay in the wall into another (see Figure 8). INSTALL WIRES (POWERED MODELS) Speaker Wires: Route each of the three supplied two conductor speaker wires from the amplifier module to the three Speaker Module locations. Utilize the space between the Screw Down Slide Brackets and the wall stud to route the wires from one to another (see Figure 8). Use the black/red pair for the right speaker, the black/white pair for the left speaker and the black/green pair for the center speaker. Power Supply Cable: Route the 24V AC power supply wire inside the wall from the rear of the In-Wall Power Supply to the Amplifier Module location using a fish tape or push/pull rod. If necessary, utilize the space between the Screw Down Slide Brackets and the wall stud to route the wire from one to another (see Figure 8). Figure 8: Routing Wire Between Stud Bays -~ :: TV Connection: Route the supplied Toslink Optical cable or the Stereo 3.5mm to dual RCA Cable or HDMI cables from the TV to the Amplifier Module. If necessary, utilize the space between the Screw Down Slide Brackets and the wall stud to route the wires from one stud to another (see Figure 8). ExternaiiR Receiver: In the event that the IR signal to the amplifier module itself is being obstructed or interfered with, the use of an externaiir receiver may be necessary. Route the IR receiver's wire and 3.5 mm plug to the Amplifier Module location. If necessary, utilize the space between the Screw Down Slide Brackets and the wall stud to route from one stud to another (see Figure 8). Auxiliary Audio Source : Route the supplied Stereo 3.5mm to dual RCA Cable to connect an auxiliary audio source. If necessary, utilize the space between the Screw Down Slide Brackets and the wall stud to route the wire from one stud bay in the wall into another (see Figure 8). Niles Wireless Subwoofer Transmitter (Optional): Route the supplied DC power cable for the wireless transmitter and a mono RCA audio cable (not supplied) from the Niles SWT location to the Amplifier Module location. If necessary, utilize the space between the Screw Down Slide Brackets and the wall stud to route the wire from one stud bay to another (see Figure 8). NILES AUDIO CORPORATION BUY HIFI

18 INSTALLING THE SYSTEM CONTINUED... POSITION THE SPEAKER MODULES IN THE IN-WALL MOUNTING SYSTEM (ALL MODELS) The Speaker Modules have small "L" shaped brackets on each side for you to use as an installation aid. These "L'' brackets enable you to temporarily "hang" the Speaker Modules on the In-Wall Mounting System making the speaker connection terminals easy to see and connect. Working within the wall stud placement, position the center speaker's centerline as close to the TV centerline as possible, the right speaker as far to the right as possible and the left speaker as far to left as possible. 1. Rotate the left and right "L'' brackets out to serve as hangers from the In-Wall Mounting System. Hang the Speaker Modules in the position that they will be inserted as shown in Figure 9. Speaker Module Amplifier Module Left "L'' Bracket Figure 9: Speaker and Amplifier Module CONNECT THE SPEAKER MODULES (ALL MODELS) 1. Prepare the speaker wire by stripping 1 /4" -1 /2" from each conductor (see Figure 10). Twist the strands or tin the leads with solder to ensure there are no stray strands that could short and possibly harm the amplifier. 2. Attach the stripped wire to the speaker wire terminals of the Speaker Module observing proper positive and negative polarity. Figure 10: Preparing the speaker wire for connection

19 CYNEMA SOUNDFIELDTM SOUNDBAR SYSTEMS INSTALLING THE SYSTEM CONTINUED... POSITION THE AMPLIFIER MODULE AND OPTIONAL SW-T IN THE IN-WALL MOUNTING SYSTEM (POWERED MODELS) Small "L" shaped brackets mounted on the sides of the Amplifier Module (identical to the "L'' brackets on the Speaker Modules) are an installation aid that allows you to "hang" the Amplifier Module on the In-Wall Mounting System making all connection terminals easy to see and connect. Working within the wall stud placement and the Speaker Module positions, place the Amplifier Module in a position that first works best with the optimal positioning of the Speaker Modules. Note: For installation in walls with vapor barriers and/or insulation, it is recommended to provide a minimum of 1" (25 mm) clearance between the vapor barrier/insulation and the housing of the amplifier. 1. Rotate the left and right "L" brackets out to serve as hangers from the In-Wall Mounting System. Hang the Amplifier Module in the position it will be inserted as shown in Figure Affix the Niles SWT to the backside of the SWT Bracket with the supplied double sided tape (see Figure 11 A) 3. Identify a location for the SWT Bracket that does not interfere with other devices to be installed in the mounting system (e.g. Amplifier/Speaker Modules and In Between Covers). 4. Rotate the SWT Subwoofer Transmitter Bracket into In-Wall Mounting System as shown in Figure 11 B, C and D. Figure 11: Installing the Niles SWT Bracket Niles SWT Adhered to Bracket (Shown from rear) A B c D NILES AUDIO CORPORATION BUY-HIFI

20 INSTALLING THE SYSTEM CONTINUED... CONNECT THE AMPLIFIER MODULE AND NILES SWT (POWERED MODELS) 1. Prepare the speaker wire by stripping 1/4" from each conductor (see Figure 10 on page 18). Twist the strands or tin the leads with solder to ensure there are no stray strands that could short and possibly harm the amplifier. 2. Connect the speaker wires and the Amplifier Module power cable to the Amplifier Module using the supplied two phoenix connectors and a small screw slotted screw driver making sure to connect in the proper order and polarity. 3. Connect all the other wires and cables routed to the Amplifier Module and SW-T as depicted in the system diagrams starting on page 24, that best matches your configuration. Important: Do not plug in the AC power cord until all other system connections are complete. NOTE: After ensuring all the connections ore mode correctly, plug in the AC power cord and test the operation of the system before completing the installation in the next steps and snapping the modules into the roils. INSTALL THE IN BETWEEN COVERS AND JOINERS (ALL MODELS) The empty spaces that are created in the In-Wall Mounting System "in between" the installed Speaker Modules and Amplifier Module are filled by the supplied In Between Covers and Joiners. In Between Covers are pre-scored and designed to be broken into the sizes needed to fill these variably sized spaces. In Between Joiners are designed to cover the seams of adjacent In between Covers. A 3/8" overhang is included on both sides of the Amplifier and Speaker Modules to make sizing the In Between Covers easier. 1. Identify and measure all of the spaces left in between the Speaker and Amplifier Modules. 2. Run a razor knife along a pre-scored marking on the back of the In Between Covers and break those into the sizes needed (see Figure 12). Figure 12: Sizing the In Between Covers NOTE: You must include a space of 3/8" to 1 /2" between any two In Between Covers that will be installed adjacent to each other. This will allow room for on In Between Joiner to be installed and to hide the seam. 3. Install the sized In Between Covers by snapping them into their respective empty spaces (see page 21 Figure 13). 4. Install an In Between Joiner by snapping it into the 3/8" to 1/2" space left between any two In Between Covers (see page 21 Figure 13)

21 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLING THE SYSTEM CONTINUED... In Between Joiner Figure 13: Install In Between Covers and Joiners INSTALL THE SPEAKER MODULES (ALL MODELS) The Speaker Modules snap into the In-Wall Mounting Systems and are held securely in the rails using spring clips built into the Speaker Module enclosure. 1. Lift the Speaker Module hanging from the In-Wall Mounting System and rotate the "L'' brackets on the left and right back into their original position being careful to make sure they are snapped over the retention pin to prevent audible vibration. 2. Insert the Speaker Module into the Wall Mounting System by inserting, rotating, and then snapping it in place as shown in Figure 14. Figure 14: Installing the Speaker Module A: Insert B: Rotate C: Snap In Rails INSTALL THE AMPLIFIER MODULES (POWERED MODELS) The Amplifier Module snaps into the In-Wall Mounting System and is held securely in the rails using spring clips built into the Amplifier Module enclosure. 1. Lift the Amplifier Module hanging from the In-Wall Mounting System and rotate the "L'' brackets on the left and right back into their original position being careful to make sure they are snapped over the retention pin to prevent audible vibration. 2. Insert the Amplifier Module into the Wall Mounting System by inserting, rotating, and then snapping it in place exactly the same way as the Speaker Module is shown in Figure Plug the AC Power cord into the face plate of the In-Wall Power Supply Box and into an AC outlet. NILES AUDIO CORPORATION BUY-HIFI

22 INSTALLING THE SYSTEM CONTINUED... SECURE THE IN-WALL MOUNTING SYSTEM (ALL MODELS) 1. Use a cordless screwdriver to firmly tighten the screws on the Screw Down Slide Brackets as shown in Figure 30 being careful to maintain proper level and alignment and that cabling is not being pinched. 2. Use a handheld screwdriver and tighten the Clamp Down End Brackets as shown in Figure 15 being careful not to over tighten. Clamp Down End Bracket Screw Down Slide Bracket PAINTING THE GRILLE (ALL MODELS) Figure 15: Secure the In-Wall Mounting System The grille can be painted without priming, but the fabric scrim on the back side must first be removed. Use several light coats sprayed from different sides and angles to cover all surfaces and not fill in any holes. If you do fill some holes, use compressed air to open them before the paint dries. It may be helpful to dilute the paint. INSTALLING THE GRILLE (ALL MODELS) The Speaker Grille magnetically attaches to the In-Wall Mounting System. Once in place, the grille can be adjusted 1" to either the left or right to achieve an exact centered position relative to the TV. 1. Place the Speaker Grill on to the In-Wall Mounting System and it will magnetically attach. 2. Slide the grille as much as 1" to the left or right to center it perfectly with the TV (see Figure 16). 1" 1" Figure 16: Centering the Speaker Grille with the TV

23 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS INSTALLING THE SYSTEM CONTINUED... REMOVING THE SPEAKER AND AMPLIFIER MODULES (ALL MODELS) The Speaker and Amplifier Modules are easily removed for service if required. 1. Gently pry out the In Between Joiners and Covers adjacent to the module requiring service using a small slotted screw driver. NOTE: To remove a Speaker and Amplifier Module installed in the same stud bay remove the Screw Down Slide Bracket from an adjacent stud. 2. Grasp the side(s) of the Speaker or Amplifier Module and pull it forward and out of the In-Wall Mounting System. NILES AUDIO CORPORATION BUY-HIFI

24 SYSTEM APPLICATIONS POWERED SYSTEM WITH OPTICAL AUDIO CONNECTION The AV system shown in Figure 17 depicts a complete Powered Cynema Soundfield System installation utilizing the TV's optical audio output to provide Dolby Digital audio. The In-Wall Power Supply Box connects to the Amplifier Module's DC main power input. AV components like Bluray and HD Satellite/Cable Boxes connect to the TV with HDMI. An auxiliary stereo input on the Amplifier Module is used for music players such as ipods and Smart Phones or the connection of a whole house audio system. The Niles SWT/SWR Wireless Subwoofer system has dedicated connections on the Amplifier Module for audio signal and DC power. Figure 17: Powered Cynema Soundfield System with Optical Audio Connection Note: For MS220 Microsensor, A 3.5mm stereo jock must be used. Optical Out Blu-ray Player (O ) wwwwnwrww < w MS220 MicroSensorTM I I L Cable Box HDMI w~~lfilllllil!liiiiigi1i'!lliilllm OUT SW6.S Compact Powered Subwoofer Important Note: Always use a fixed level audio out when connecting a Whole House Audio System or a Local Audio Source (e.g. ipod). This will simplify operation and enable the Cynomo Soundfield Amplifier Module to always be your primary volume control

25 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS SYSTEM APPLICATIONS CONTINUED... POWERED SYSTEM WITH ANALOG AUDIO CONNECTION The AV system shown in Figure 18 depicts a complete Powered Cynema Soundfield System installation utilizing the TV's analog audio output to provide a simulated 3-channel sound field. The In-Wall Power Supply Box connects to the Amplifier Module's DC main power input. AV components like Bluray and HD Satellite/ Cable Boxes connect to the TV with HDMI. An auxiliary stereo input on the Amplifier Module is used for music players such as ipods and Smart Phones or the connection of a whole house audio system. The Niles SWT/ SWR Wireless Subwoofer system has dedicated connections on the Amplifier Module for audio signal and DC power. Figure 18: Powered Cynema Soundfield System with Analog Audio Connection r _iijltfmiiq.ii&qijilij.ji;fi Note: For MS220 Microsensor, o 3.5mm stereo jock must be used. N :E :E ~ ~ Blu-ray Player Cable Box Whole-House Audio System OR SW6.5 Compact Powered Subwoofer lmportont Note: Always use o fixed level audio out when connecting o Whole House Audio System or o Local Audio Source (e.g. ipod). This will simplify operation and enable the Cynomo Soundfield Amplifier Module to always be your primary volume control. NILES AUDIO CORPORATION BUY-HIFI

26 !'_'. Fixed SYSTEM APPLICATIONS CONTINUED... POWERED SYSTEM WITH HDMI CONNECTION The AV system shown in Figure 19 depicts a complete Powered Cynema Soundfield System installation utilizing an HDMI switching matrix output to provide Dolby Digital sound quality. The In-Wall Power Supply Box connects to the Amplifier Module's DC main power input. AV components like Bluray and HD Satellite/Cable Boxes connect with HDMI to the switching matrix, which connects with HDMI to the Amplifier Module, which then connects with HDMI to a TV. An auxiliary stereo input on the Amplifier Module is used for music players such as ipods and Smart Phones or the connection of a whole house audio system. The Niles SWT/SWR Wireless Subwoofer system has dedicated connections on the Amplifier Module for audio signal and DC power. Figure 19: Powered Cynema Soundfield System with HDMI Connection Note: For MS220 Microsensor, A 3.5mm stereo jack must be used. ' ~ = = = = = = = =F- ::::::::::::::::.::::-.::::-~- -@Miii@f.iliijW.i.+Hi$.!4-, HDMil I... Blu-ray Player MS220 MicroSensor'M I HDMI OUT L - I SW-T Wireless Transmitter Cable Box HDMI OUT [ ~.. ~ ~. r-. Whole-House Audio System ~-- or...,... ~ ~. ~ ~ - tiiiiiiiiiii] ~. Audio j ~~ - s:j::; Q: z~-~-~- 0~~ SW6.5 Compact Powered Subwoofer Important Note: Always use a fixed level audio out when connecting a Whole House Audio System or a local Audio Source (e.g. ipod). This will simplify operation and enable the Cynama Soundfield Amplifier Module to always be your primary volume control

27 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS SYSTEM APPLICATIONS CONTINUED... PASSIVE SYSTEM The AV system shown in Figure 20 depicts a complete Passive In-Wall Modular Sound bar installation utilizing an AV receiver to provide source selection, signal decoding, volume control, and amplification. AV components like Bluray and HD Satellite/Cable Boxes connect with HDMI to the AV receiver which connects with HDMI to the TV. Audio source components and audio accessories, such as ipods, smart phones and subwoofers are included for added listening options. Figure 20: Passive Cynema Soundfield System In-Wall Mounted System SW6.5 Compact Powered Subwoofer NILES AUDIO CORPORATION BUY-HIFI

28 OPERATION POWERED SYSTEMS POWERED CYNEMA SOUNDFIELD SYSTEMS The Amplifier Module included with Powered Cynema Soundfield Systems amplifies the sound for the Speaker Modules. Signal activation and priority input switching automatically turn the Amplifier Module on and select a prioritized input for simple operation. Push buttons provide manual control from the front panel and a built in infrared receiver provides control from a learning IR remote control or the remote control included with the Flat Panel TV. LED INDICATORS LED indicators located on the Amplifier Module's front panel are included to provide useful real time operational feedback (see Figure 21). The LED indicators illuminate only when the Amplifier Module signal activates or when it automatically switches input. In addition, using an IR remote control or the front panel buttons will cause the LED indicators to illuminate. NOTE: All of the LED indicators turn completely off after three seconds of operational inactivity to prevent distraction while viewing TV. Figure 21: LED Indicator Descriptions NAME DESCRIPTION A solid green Power LED indicates the Amplifier Module is "ON". A solid red Power LED indicates the Amplifier Module is "OFF". Power LED A flashing red Power LED indicates the amplifier is in a fault condition and the protection circuit has activated. A rapidly blinking green Power LED indicates a valid IR command is being received by the built in IR receiver. A solid green Status LED indicates that Wide Audio Mode is off. Status LED A solid red Status LED indicates that Wide Audio Mode is On. See page 30, Figure 23 for more details regarding Wide Audio Mode. A solid green Source LED indicates the optical I HDMI source input is active and selected. Source LED A solid red Source LED indicates the analog AUXIn source is active and selected. A solid orange Source LED indicates the analog Line In source is selected

29 CYNEMA SOUNDFIELDTM SOUNDBAR SYSTEMS OPERATION POWERED SYSTEMS CONTINUED... AUTOMATIC CONTROL Automatic System Activation The Amplifier Module automatically powers on when an audio signal is present at the Optical, HOM I, Line or Aux inputs. The Amplifier Module subsequently powers off in the absence of an audio signal at all inputs after 3 minutes. Automatic System Input Selection The Amplifier Module automatically selects a source when an audio signal becomes present at the input connections. In the event audio is present at both the Video (Optical, HDMI, or Line) and Aux Inputs simultaneously, automatic priority input selection is given to the Video Input. NOTE: When a source is connected to the line or oux input, the muting of that source may result in the automatic system input selection feature searching for the next active input before sound is restored. Automatic Sound Mode Selection The Amplifier Module automatically selects the appropriate surround sound mode for the currently selected input as shown in Figure 22 below. NAME DESCRIPTION Optical/HOM I Dolby Digital Line Dolby Pro Logic Aux Music Mode Figure 22: Surround Sound Modes MANUAL CONTROL Power Button The Power Button toggles the Amplifier Module on and off. NOTE: The Amplifier Module will also always turn on when on active input signal is detected. Source Selection Button The Source Button provides sequential selection of the Video Input (Opticai/HDMI/Line) or the Aux Input. Manual selection of input using the Source Buttons overrides the Amplifier Module's automatic input selection. Volume Up/Down Buttons The Volume Up/Down Buttons control the Main Volume Up and Down. Mute Button The Mute Button mutes or unmutes the Main Volume. Left/Center/Right Level Buttons The Left/Center/Right Level Buttons balance the individual level of each speaker module to compensate for asymmetrical speaker placement in the In-Wall Mounting System. NILES AUDIO CORPORATION BUY-HIFI

30 OPERATION POWERED SYSTEMS CONTINUED... INFRARED REMOTE CONTROL Infrared remote control commands that operate the Amplifier Module are available for download at These remote control commands are available in formats compatible with most learning remote controls. Refer to Figure 23 for a list of the remote control commands and a description of their Amplifier Module function. Figure 23: IR Remote Control Commands IR COMMAND AMPLIFIER MODULE FUNCTION Power Toggles Amplifier Module on and off Source Cycles through each input selection Main Volume Up Raises the Main volume Main Volume Down Lowers the Main volume Main Volume Mute Mutes and un-mutes the Main volume Left Volume Up Raises the Left speaker volume Left Volume Down Lowers the Left speaker volume Center Volume Up Raises the Center speaker volume Center Volume Down Lowers the Center speaker volume Right Volume Up Raises the Right speaker volume Right Volume Down Lowers the Right speaker volume Aux Selects the Aux Input Hotel/Night Sound Volume is limited to 70 /o of maximum and bass response is reduced Wide Audio Mode Creates perception of wider sound field A Xantech IR Receiver's 3.5mm, 3-conductor plug can be connected directly to the Amplifier Module and located for convenient operation from an IR remote control (see Figure 17). IR Input Contact Configuration: Tip = IR signal; Ring = Ground for power and IR signal; Sleeve = 12V to power an IR receiver. Important Note: You must use o three conductor mini-plug (Tip/Ring/Sleeve) and connect only the Tip and Ring if you ore connecting the IR control output of on RF to IR bose station or AV control system rather than connecting on IR receiver. The use of a two conductor mini-plug (Tip/Sleeve) in this instance will short 12V to Ground and may cause damage to the Amplifier Module

31 CYNEMA SOUNDFIELD SOUNDBAR SYSTEMS OPERATION POWERED SYSTEMS CONTINUED... LEARNING INFRARED COMMANDS In addition to the infrared control available from the remote control commands in Figure 23, the Amplifier Module can learn the power, volume and mute command from any infrared remote control for control from one hand held remote. Steps for learning Infrared commands into the Amplifier Module 1. Press the Power button and Volume+ (Vol+) button simultaneously until the Power LED blinks orange. 2. The Power, Vol+, Vol-, and Mute functions can be learned by the Cynema Soundfield Amplifier Module. As an example, let's start with the Vol+ command. Press the Vol+ button on the Amplifier Module. The Power LED will light constant orange. 3. Aim the TV remote at the Amplifier Module's built in IR receiver from about 1 ft (30 em) and press the corresponding Vol+ button 4 times until the Power LED lights green. This indicates that the Amplifier Module has learned the command. 4. Repeat steps 1 to 4 to teach commands to the remaining functions. Note for cable/satellite users: If you plan to use the universal remote supplied with your cable/satellite box to operate your Cynema Soundfield System, that universal remote itself may not be able to properly program the Cynema Soundfield System. Instead, use the original remote control supplied with the television: Following programming with the television's remote, the Cynema Soundfield System will respond appropriately to the cable/satellite box universal remote. OPERATION PASSIVE SYSTEMS PASSIVE CYNEMA SOUNDFIELD SYSTEMS Refer to the operating instructions of the AV receiver connected to the Speaker Modules when using a passive Cynema Soundfield System. NILES AUDIO CORPORATION BUY-HIFI

32 LIMITED WARRANTY Niles Audio, a division of Core Brands, ("NILES") warrants to the original retail purchaser only that this product will be free of manufacturing defects in material and workmanship for the following periods and subject to the limitations and exclusions set forth below: Lifetime Warranty All Passive Amplifier Products (those not requiring AC or battery power). Ten years from the date of purchase All Other Passive Products (those not requiring AC or battery power). Two years from the date of purchase All Active Products (those requiring AC or battery power). This warranty is not transferable to subsequent purchasers of the product. To obtain warranty service, contact the authorized dealer where you purchased your product or take the unit to the nearest authorized NILES dealer (with proof of purchase- claims made without proof of purchase will be denied) who will test the product and if necessary, forward it to NILES for service. If there are no authorized NILES dealers in your area, you must contact NILES to receive a factory Return Authorization Number. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITIEN AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES. Upon examination, NILES will, at its sole option and expense, repair or replace any product found to be defective. NILES will return the repaired or replaced unit to you via its usual shipping method from the factory to your address in the United States of America or Canada only. Any shipping costs for addresses outside of the United States or Canada shall be the responsibility of the purchaser. In the event that this model is no longer available and cannot be repaired effectively, NILES, at its sole option, may replace it with a different model of equal or greater value, or refund the original purchase price paid. THE FOREGOING ARE YOUR EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY. This Warranty does not include service or parts to repair damage caused by improper use or handling, including but not limited to damage caused by accident, mishandling, improper installation, commercial use, abuse, negligence, or any defect caused by repair to the product by anyone other than NILES. This warranty does not cover reimbursement for your costs of removing and transporting the product for warranty service evaluation, or installation of any replacement product provided under this warranty. This Warranty will be void if: the Serial Number on the product has been removed, tampered with or defaced. the product was not purchased from an authorized dealer or reseller. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. NILES EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, WITH RESPECT TO THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW, EVEN IF NILES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Notwithstanding the above, if you qualify as a "consumer" under the Magnuson-Moss Warranty Act, or applicable state laws, then you may be entitled to any implied warranties allowed by law for the Warranty Period. Further, some states do not allow limitations on how long an implied warranty lasts or allow the exclusion or limitation of consequential damages, so such limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. For the name of your nearest authorized NILES dealer, contact: NILES AUDIO, 1800 South McDowell Blvd, Petaluma, California 94954, or call , Please be advised that NILES only sells its products via the Internet through a select group of authorized Internet dealers. These are listed on our website at Products offered on the Internet through unauthorized Internet dealers are not covered by the NILES warranty and may be either: 1) goods acquired on a secondary or grey market 2) counterfeit or stolen goods 3) damaged, or defective goods Please fill in your product information and retain for your records. Model Serial No. Purchase Date ATTENTION: TO OUR VALUED CONSUMERS: To insure that consumers obtain quality pre-sale and after-sale support and service, NILES products are sold exclusively through authorized dealers. This warranty is VOID if the products have been purchased from an unauthorized dealer