INSTALLATION ADJUSTMENT SERVICE TM-1520A-DT, TM-2020A-DT PARALLEL SYSTEMS
|
|
- Justina Banks
- 5 years ago
- Views:
Transcription
1 ASSE 1 17 TERMOSTATI F 3 R ASSE 1 17 TERMOSTATI VALVE O. RANSTON RI USA TYP TM US. Patents 2.97, 3,61, , F 3 R VALVE O. RANSTON RI USA TYP TM US. Patents 2.97, 3,61, ,7 Bulletin G1N1 January 7 INSTALLATION ADJUSTMENT SERVIE TM-15A-DT, TM-A-DT PARALLEL SYSTEMS Note: Each individual valve assembly is ASSE 117 listed. IMPORTANT! Provide serial numbers for both valves when ordering parts!! INSTALLATION 43" 39" L 3" OT 33 1/2" OLD OT 28" OLD TM-A-DT TM-15A-DT 1. Type TM Parallel Systems are factory pre-assembled and tested and include large and small thermostatic water mixing valves which function as a system to meet both high and low demand for tempered water. 2. System should be installed at a location where it can easily be cleaned, adjusted or repaired. 3. System supplies must be connected as shown (ot-left, old-right). Exercise caution when soldering. 4. Flush pipes thoroughly after system has been connected. 5. Assemblies installed on a recirculated hot water system MUST be piped according to S REQUIRED PIPING METOD #5 (see page 4). 6. Refer to page 3 of this bulletin for correct Setup Instructions. Maximum Operating Pressure 125PSI (8 KPA) for ot and old Water. AUTION All thermostatic water-mixing valves have limitations. They will not provide the desired accuracy outside of their flow capacity range. onsult the capacity chart on page 12. Minimum flow must be no less than as shown. 13 Elmwood Avenue, ranston, RI 291 USA Phone: Fax: info@leonardvalve.com Web Site:
2 ADJUSTMENT AND SERVIE Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: Parallel Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and Record MGR-11 WARNING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 1 F (49 ) with an incoming hot water supply temperature of 15 F (65.5 ). If the hot water supply temperature of the job is greater than 15 F (65.5 ), the valves when turned to full OT will deliver water in excess of 1 F (49 ) and the limit stop MUST BE RESET BY TE INSTALLER! TO RESET ADJUSTABLE IG TEMPERATURE LIMIT : TM-B LARGE MIXING VALVES TM-B SMALL MIXING VALVES TERMOSTATI SREW D L LTR SET SREW FINE ADJUSTMENT SREW OT LTR SET SREW SNAP AP WEB RETAINING RING 1. Loosen LTR screw 2. Remove SNAP AP, SREW & WASER, Remove. 3. Temporarily place on the spline rod, turn RIGT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. Replace on the spline rod so that its RIGT edge is resting against the SREW located on the RIGT SIDE OF TE. 5. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. 1. Remove SNAP AP, SREW & WASER &. 2. Loosen LTR screw, and remove retaining ring and stop. 3. Temporarily place on the spline rod, adjust to desired temperature, and remove the pointer. 4. Push stop on rod so that its RIGT edge is resting against the fine adjustment screw on cover. 5. Turn, fine adjustment screw if necessary, (clockwise for slightly higher temperature, counter clockwise for slightly lower temperature). 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. IMPORTANT! ALL MIXING VALVES MUST BE SET AT TE SAME OPERATING TEMPERATURE. SEE PAGES: 6 & 7 FOR OMPLETE PARTS BREAKDOWN heck for significant variations in outlet flow. Thermostatic valves will NOT provide the desired accuracy outside of their flow capacity range. Minimum flows must be no less than shown (see Flow apacities, page 12). If installed on a recirculated hot water system, make certain the valve is piped according to Leonard s Required Piping Methods (see page 4). REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. (SEE MAINTENANE GUIDE AND REORD, MGR-11). 2
3 L D ADJUSTMENT AND SERVIE Leonard Type TM Thermostatic Water Mixing Valves are simple in design and may be easily cleaned, adjusted and repaired. If the installation is accessible, servicing may be completed without disconnecting the valves. NOTE: Parallel Systems include Thermostatic Water Mixing Valves, which must be regularly maintained to provide best performance. Frequency of cleaning depends on quality of local water conditions and usage. See Maintenance Guide and Record MGR-11 WARNING These mixing valves are equipped with an adjustable high temperature limit stop factory set at approximately 1 F (49 ) with an incoming hot water supply temperature of 15 F (65.5 ). If the hot water supply temperature of the job is greater than 15 F (65.5 ), the valves when turned to full OT will deliver water in excess of 1 F (49 ) and the limit stop MUST BE RESET BY TE INSTALLER! TO RESET ADJUSTABLE IG TEMPERATURE LIMIT : TM-15A LARGE MIXING VALVE TERMOSTATI SREW FINE ADJUSTMENT SREW TM-15A SMALL MIXING VALVE OT LTR SET SREW SNAP AP LTR SET SREW 1. Loosen LTR screw 2. Remove SNAP AP, SREW & WASER, Remove. 3. Temporarily place on the spline rod, turn RIGT for warmer temperature, turn LEFT for cooler temperature. When valve is delivering warmest temperature desired, remove the pointer. 4. Replace on the spline rod so that its RIGT edge is resting against the SREW located on the RIGT SIDE OF TE. 5. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. WEB RETAINING RING 1. Remove SNAP AP, SREW & WASER &. 2. Loosen LTR screw, and remove retaining ring and stop. 3. Temporarily place on the spline rod, adjust to desired temperature, and remove the pointer. 4. Push stop on rod so that its LEFT edge is resting against the fine adjustment screw on cover. 5. Turn, fine adjustment screw if necessary, (clockwise for slightly higher temperature, counter clockwise for slightly lower temperature). 6. The new maximum temperature has now been set. Test this temperature by holding a thermometer under the flow of water to be certain it is as desired. IMPORTANT! ALL MIXING VALVES MUST BE SET AT TE SAME OPERATING TEMPERATURE. SEE PAGES: 9 & 11 FOR OMPLETE PARTS BREAKDOWN heck for significant variations in outlet flow. Thermostatic valves will NOT provide the desired accuracy outside of their flow capacity range. Minimum flows must be no less than shown (see Flow apacities, page 12). If installed on a recirculated hot water system, make certain the valve is piped according to Leonard s Required Piping Methods (see page 4). REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. (SEE MAINTENANE GUIDE AND REORD, MGR-11). 3
4 ASSE 117 TERMOSTATI F R ASSE 117 TERMOSTATI SETUP INSTRUTIONS TERMOMETER V1L V2L LVL V2R V1R LVR SVL SVR OT INLET OLD INLET 1. The Parallel Unit MUST be piped according to a Leonard Required Piping Method 5 (see page 4). 2. Make sure full hot and cold supplies to this assembly are operating. The temperature of the hot water source must be properly set and maintained. 3. The circulator (if used) must be turned OFF before setup. 4. Turn on enough fixtures for a flow of at least 3 GPM (114 l/min.) downstream from this system. Make sure each fixture is set to deliver full "OT" water. 5. lose outlet ball valves V1R,V2R, V1L. 6. Make sure ball valve V2L is in the full open position. 7. Set outlet temperature of the mixing valve LVL to the required level. 8. Open ball valve V2R and shut ball valve V2L at the mixing valve. 9. Set outlet temperature of the mixing valve LVR to the same temperature as STEP Turn off enough fixtures for a flow of at least 2 GPM (7.6 l/min) downstream from this system. Make sure each fixture is set to deliver full "OT" water. 11. Open V1L, shut off ball valve V2R. 12. Set outlet temperature of mixing valve SVL to the same temperature as Step Open V1R and shut V1L, set outlet temperature of SVR mixing valve to the same temperature as STEP Open all outlets. System is operational. To balance circulation system temperature, see page 5. NOTE! FOR OPTIONAL OUTLET SETUP PIPING ARRANGEMENT, SEE PAGE 12 4
5 REQUIRED PIPING METOD #5 IG TEMPERATURE FIXTURES SYSTEM FIXTURES BALL VALVE FOR SETUP (OPTIONAL) FULL RETURN LINE SIZE OT WATER SOURE EAT TRAP BALANING VALVE #2 WIT EK TEMPERED IRULATOR EK VALVE ISOLATION VALVE T AQUASTAT OLD SUPPLY EK VALVE BALANING VALVE #1 IG TEMPERATURE RETURN IRULATOR TEMPERED RETURN PROEDURE TO BALANE IRULATION SYSTEM 1. MAKE SURE NO WATER IS BEING DRAWN IN TE BUILDING. OPEN BALANING VALVE #1 APPROXIMATELY ALF WAY AND START IRULATOR. KEEP BALANE VALVE #2 LOSED AT TIS TIME. 2. OBSERVE TEMPERATURE UNTIL IT STABILIZES. 3. LOSE BALANING VALVE #1 SLIGTLY IF TEMPERATURE IS TOO OT, OR OPEN IT SLIGTLY IF TEMPERATURE IS TOO OLD. ALLOW TEMPERATURE TO STABILIZE, REPEAT UNTIL DESIRED IRULATION TEMPERATURE IS SET. 4. IF UNABLE TO REA DESIRED TEMPERATURE WIT VALVE #1 IN TE FULL OPEN POSITION, OPEN BALANE VALVE #2 IN SMALL INREMENTS (i.e. 1/8, ¼, 3/8, ET) UNTIL DESIRED TEMPERATURE IS AIEVED. REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD, MGR-11). 5
6 INSTRUTIONS FOR SERVIING LARGER TMA VALVE INSTRUTIONS FOR SERVIING SMALLER TMA VALVE 1. Loosen LTR set screw 2. Remove snap cap, screw and washer, friction spring and pointer. 3. Turn off hot and cold supplies at checkstops. Remove TM-16 cover screws to release cover and thermostatic control assembly. 4. To clean port sleeve assembly, (the thimble must move freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into the base. The port sleeve and thimble may be lifted out. SEE DWG BELOW 5. lean in a non-corrosive cleaning solution. DO NOT USE ABRASIVES! The port sleeve should be reassembled in the valve. TIMBLE 1. Remove screw, snap cap, and handle. 2. Loosen LTR set screw. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove M-2 (P) cover screws to release cover and thermostatic control assembly. 4. To remove bridge assembly, TM B, remove pointer rod nut (MU-1B) and pull bridge assembly off control rod. 5. To clean submerge bridge assembly in clean water or noncorrosive cleaning solution. DO NOT USE ABRASIVES! Be certain thimble moves freely on port sleeve. Note! Driving ball on thimble must engage coil bracket in assembling. TM B BRIDGE ASSY EK NUT PORT SLEEVE PORT SLEEVE NUT 6. To clean thermostat group, remove coil sleeve stud and take off thermostat group. 7. lean in a non-corrosive cleaning solution. 8. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. MU-1B ROD NUT 6. To disassemble bridge assembly, see drawing next page (remove TM25-3A holder nuts with screwdriver in slots provided). 7. Remove thermostat group from bridge assembly, and soak in a non-corrosive cleaning solution. TROUBLESOOTING INSTRUTIONS Note: Provide serial number when ordering parts for each valve! LARGE VALVE SMALL VALVE PAKING & S 1. Leaks at stem. 2. Leak between valve cover and base. Repair Kit # 1/Y Repair Kit # 1/28Y (Packings & Gaskets) /BRIDGE ASSEMBLY 3. Valve delivers either all hot or all cold water, or will not mix consistently. Repair Kit # R/N Repair Kit #R/28 (Rebuilding Kit) or TM28-1-8B Bridge Assembly TERMOSTAT GROUP 4. After cleaning or replacing port sleeve/ bridge assembly, valve performance is not consistent. Repair Kit # R/N Repair Kit #R/28 (Rebuilding Kit) or TM-28-G2 Thermostat Group EKS 5. ot water by-pass into cold line(or cold into hot). 6. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. Repair Kit #2/Y Repair Kit #2/28Y (heckstop Kit) 6
7 TERMOSTATI 57-L SNAP AP TM-B LARGE VALVE PARTS TM-25 TM-15B/ TM-25D TGM-2/125 TERMOSTAT GROUP TM-8 OIL SLEEVE STUD TERMOSTATI TM-3 FRITION TM-28A ROD TM-29/29A SREW W/WASER TM-16A DIAL PLATE TM-16 SREWS TM-21/125 FLANGE PAKING TGM-1/ ASSY TM-3/ NUT ASSY TM-16 DIAL PLATE EK PARTS REPAIR KITS 477 SWIVEL NUT 4733 & PAKING/ 474 SWIVEL YELLOW 4727 UPPER STEM 313 S (2) 4728 AP WASER 4723 AP KIT 1/Y * PAKINGS & S **=2 EA YELLOW ** & PAKING ** 313 UPPER STEM (4) KIT R/N * REBUILDING KIT TM-3/ NUT ASSY. TM-21/125 FLANGE PKG SREEN ** TM-28A ROD ROD 4728 AP WASER** TM-21/125 FLANGE PKG. LOK-TYPE TM-36 SET SREW TM-8 OIL SLEEVE STUD KIT 2/Y * EK KIT 2 EA: 4733 & PAKING TGM-1/ ASSY. 313 STEM (4) 4742 YELLOW 4724 SREEN TGM-2/125 TERMOSTAT GROUP 4728 AP WASER REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD) NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT ON EA VALVE (SEE PAGE 2). 7
8 TMA SMALL VALVE PARTS 57-L SNAP AP MU-13D RETAINING RING TM-36 SREW 57-D RF GLAND NUT 334 DIAL PLATE 214 M-3 TM-29/29A SREW W/WASER MU-5D MU-9D TM B BRIDGE ASSEMBLY MU-4 MU-1B GLAND PAKING ROD NUT TM25-3 TM-25-3A P.S. OLDER P.S. OLDER NUT TGM-1/28 TM-28-6B ASSEMBLY OLDER NUT TM25-5 BRIDGE TM28-G2 TERMOSTAT GROUP TM25-3B P.S. PAKING EK PARTS REPAIR KITS 3 & PAKING 4519 YELLOW 4 SWIVEL 9 SWIVEL NUT UPPER STEM 1 RF 13 SREEN 5 PAKING 14 AP PAKING 6 STRAINER AP TM-2 BONNET KIT 1/28Y PAKINGS & S 4519 YELLOW MU-4 GLAND PKG. 5 BONNET PKG. KIT R/28 REBUILDING KIT M-3 14 AP PAKING M-3 13 SREEN TM-28-6B OLDER NUT 3 & PKG. TM B TERMOSTATI ONTROL ASSEMBLY LOK-TYPE KIT 2/28Y EK KIT 2 EA: 3 & PAKING UPPER STEM 4519 YELLOW 14 AP PAKING 13 SREEN 5 BONNET PKG. REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS (SEE MAINTENANE GUIDE AND REORD, MGR-11). NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT ON EA VALVE (SEE PAGE 2). 8
9 INSTRUTIONS FOR SERVIING LARGER TM15A VALVE INSTRUTIONS FOR SERVIING SMALLER TM15A VALVE DRIVING BALL BALL SOKET SREW W/WASER SREWS (4 REQ'D) LTR SREW M-2 (P) SREWS TERMOSTAT GROUP FLANGE PAKING 1. Remove screw, snap cap, and pointer. 2. Loosen LTR set screw. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove cover screws to release cover and thermostat group. TIMBLE EK NUT SNAP AP TM B TERMOSTATI ONTROL ASSEMBLY M-3 1. Remove screw, snap cap, and pointer. 2. Loosen LTR set screw. 3. Turn off hot and cold supplies at screwdriver checkstops. Remove M-2(P) cover screws to release cover and thermostatic control assembly. 4. To remove bridge assembly, M-1-8B, remove pointer rod nut (MU-1B) and pull bridge assembly off control rod. M-1-8B BRIDGE ASSY PORT SLEEVE PORT SLEEVE NUT TIMBLE M-5B P.S. OLDER NUT 4. To clean, port sleeve assembly (the thimble must slide freely on the port sleeve): unscrew the check nut as far as it will go, then screw the port sleeve nut into base. The port sleeve and thimble may then be lifted out. 5. To clean thermostat coil, remove coil sleeve stud and take off thermostat group. 6. lean with a non-corrosive cleaning solution. DO NOT USE ABRASIVES! 7. When reassembling, make sure driving ball of thermostat group engages the ball socket of the port sleeve assembly. MU-1B ROD NUT 5. To clean, submerge bridge in clean water or non-corrosive cleaning solution. DO NOT USE ABRASIVES! Be certain thimble moves freely on the port sleeve. Note! Driving stud (M-14B) must engage slot in thimble when reassembling. 6. To clean thermostat coil, remove retaining ring and stop, loosen gland nut. Push rod through cover. Be careful not to pull coil out of shape. 7. lean with a non-corrosive cleaning solution. DO NOT USE ABRASIVES! TROUBLESOOTING INSTRUTIIONS Note: Provide valve serial number when ordering parts for each valve! Large Valve Small Valve PAKING & S 1. Leak at stem 2. Leak between valve cover and base. Repair Kit 1/125Y Repair Kit 1/M (Packings & Gaskets) /BRIDGE ASSEMBLY 3. Valve delivers either all hot or all cold water, or will not mix consistently. Repair Kit R/125 Repair Kit R/M TM- (Rebuilding Kit) or M- 1-8B Bridge Assembly TERMOSTAT GROUP 4. After cleaning or replacing port sleeve/bridge assembly, valve performance is not consistent. Repair Kit R/125 or TGM- 125 Repair Kit R/M (Rebuilding Kit) or M- G2 Thermostat Group EKS 5. ot water by-pass into cold line (or cold into hot). 6. Supplies cannot be shut off completely. Supplies leak at checkstop bonnets. Repair Kit 2/5Y Repair Kit 4/M (heckstop Kit) See pages 1 & 11 for parts Breakdowns 9
10 TM15A LARGE VALVE PARTS 57-L RF/P SNAP AP TM-25 RF/P TM-15B/125 (152) Serial No's RF/P TM-25D RF/P TGM-2/125 (152) Serial No's TERMOSTAT GROUP TM-8 OIL SLEEVE STUD TERMOSTATI TM-29/29A SREW W/WASER 3 FRITION TM-16 SREWS TM-28A ROD TM-16A/125 (152) Serial No's DIAL PLATE TM21/125 (152) Serial No's FLANGE PAKING TGM-1/125 (152) Serial No's ASSY TM-3/125 (152) Serial No's NUT ASSY EK PARTS REPAIR KITS REPAIR KIT 1/125Y PAKINGS & S 3 & PAKING UPPER STEM 1 RF/P 5 PAKING **=2 EA. ** TM21/125 (152) Serial No's FLANGE PKG 13** SREEN 5** BONNET PKG YELLOW 13 SREEN 4/125 RF/P (152) Serial #'s SWIVEL TM-2 RF/P BONNET 14 AP PAKING 1529 ** 3** YELLOW & PAKING 14** AP PAKING 9/125 RF/P (152) Serial #'s 6 RF/P STRAINER AP REPAIR KIT R/125 TM-15A REBUILDING KIT LOK-TYPE TM-3/125 (152) Serial No's NUT ASSY. TM-28A ROD TM21/125 (152) Serial No's FLANGE PKG TM-36 SET SREW TGM-1/125 (152) Serial No's ASSY TGM-2/125 (152) Serial No's TERMOSTAT GROUP TM-8 OIL SLEEVE STUD REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. SEE MAINTENANE GUIDE AND REORD MGR-11. NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT ON EA VALVE (SEE PAGE 8). REPAIR KIT 2/5Y EK KIT 2 EA: 3 & PAKING 13 SREEN AP PAKING YELLOW 5 BONNET PKG. 1
11 TM15A SMALL VALVE PARTS 57-L(P) SNAP AP MU-13D RETAINING RING 57-D(RF) GLAND NUT M-1(RF)(P) M-3 57-M SREW W/WASER MU-5D MU-9D M-14B DRIVING STUD M--1-8B BRIDGE ASSEMBLY MU-4 GLAND PAKING M-5B P.S. OLDER NUT M-6B OLDER NUT M-1B BRIDGE M-G2 TERMOSTAT GROUP R DURA-trol MU-1B ROD NUT M-4B P.S. OLDER M-G1 ASSEMBLY M-3B P.S. PAKING M-14B DRIVING STUD EKS EK PARTS M-3A BONNET PAKING LOK-TYPE TM-36 SET SREW M-9A EK M-6A LOWER STEM & PAKING MU-4A RF UPPER STEM AND PAKING UPPER STEM PKG. M-2A RF EK BONNET REMEMBER! TIS IS A ONTROL DEVIE WI MUST BE LEANED AND MAINTAINED ON A REGULAR BASIS. SEE MAINTENANE GUIDE AND REORD MGR-11. NOTE: AFTER INSTALLING NEW PARTS IT WILL BE NEESSARY TO RESET TE ADJUSTABLE IG TEMPERATURE LIMIT ON EA VALVE (SEE PAGE 8). MU-4 GLAND PKG. REPAIR KITS REPAIR KIT 1/M PAKINGS & S REPAIR KIT R/M REBUILDING KIT M-3 M-1-12B TERMOSTATI ONTROL ASSEMBLY REPAIR KIT 2/M KIT M-6B OLDER NUT REPAIR KIT 4/M EK KIT M-9A EK M-9A EK M-3A BONNET PKG. M-3B P.S. PAKING M-6A & PKG. M-3 M-6A & PKG. M-G1 PORT SLEEVE ASSY. M-6B OLDER NUT M-3A BONNET PKG. 11
12 R F OPTIONAL OUTLET SETUP PIPING (BY OTERS) The addition of this piping arrangement (extra tee and ball valve) eliminates the need to turn fixtures on and off throughout the building at setup. The flows required in the setup instructions (page 3) are set by using Ball Valve A. (make sure main outlet ball valve is closed). MAIN OUTLET BALL VALVE TEMPERED WATER TO BUILDING BALL VALVE A AUTION! ALL TERMOSTATI WATER MIXING VALVES AND SYSTEMS AVE LIMITATIONS! TEY WILL NOT PROVIDE TE DESIRED PERFORMANE OUTSIDE OF TEIR FLOW APAITY RANGE! ONSULT TE APAITY ART BELOW AND OBSERVE MINIMUM FLOWS SOWN. FLOW APAITIES TM-15A-DT PARALLEL MINIMUM FLOW (GPM) (l/min) SYSTEM PRESSURE DROP (PSIG) PSI BAR GPM l/min TM-A-DT PARALLEL MINIMUM FLOW (GPM) (l/min) SYSTEM PRESSURE DROP (PSIG) PSI BAR GPM l/min LIMITED WARRANTY Leonard Valve ompany warrants the original purchaser that products manufactured by them (not by others) will be free from defects in materials and workmanship under normal conditions of use, when properly installed and maintained in accordance with Leonard Valve ompany's instructions, for a period of one year from date of shipment. During this period the Leonard Valve ompany will at its option repair or replace any product, or part thereof, which shall be returned, freight prepaid, to the Leonard factory and determined by Leonard to be defective in materials or workmanship. There are no warranties, express or implied, which extend beyond the description contained herein. There are no implied warranties of merchantability or of fitness for a particular purpose. In no event will Leonard be liable for labor or incidental or consequential damages. Any alteration or improper installation or use of the product will void this limited warranty. 12 Printed in USA
INSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD TM-2020B
2 4 1 11 7 6 8 2 3 4 5-1 6 F 14 TERMOSTATI 1 12 2 ASSE 117 6 4 1 8 2 3 4 5-1 6 F 14 TERMOSTATI 1 12 Bulletin G-11E June 29 INSTALLATION ADJUSTMENT SERVIE IG-LOW MANIFOLD TM-22B Valve assembly is ASSE 117
More informationINSTALLATION ADJUSTMENT SERVICE 2P TM-2020B-2P, TM2020B-2P-LF PARALLEL SYSTEMS
OT ASSE 117 4 2 1-1 2 3 R F 8 14 4 5 1 12 ASSE 117 VALVE O. RANSTON RI USA AS SE 117 TYP TM US. Patents 2.97, 3,61,195 3.152,7 4 2 1-1 2 F 3 R 8 5 14 4 1 12 VALVE O. RANSTON RI USA ASSE 117 U S. Pate nt
More informationINSTALLATION ADJUSTMENT SERVICE 2PS TM-2020B-2P, TM2020B-2PS-LF PARALLEL SYSTEMS
OT ASSE 117 TERMOSTATI 4 2 1-1 2 3 R F 8 14 4 5 1 12 ASSE 117 TERMOSTATI LF VALVE O. RANSTON RI USA TYP TM LF 4 2 1-1 2 F 3 8 5 14 4 1 12 LF VALVE O. RANSTON RI USA TYP TM LF Bulletin G11N5 March 215 INSTALLATION
More informationINSTALLATION ADJUSTMENT SERVICE TM-1520A-2P, TM-1520A-2P-LF TM-2020B-2P, TM2020B-2P-LF PARALLEL SYSTEMS
OT ASSE 117 4 2 1-1 2 3 R F 8 14 4 5 1 12 ASSE 117 VALVE O. RANSTON RI USA AS SE 117 TYP TM US. Patents 2.97, 3,61,195 3.152,7 4 2 1-1 2 F 3 R 8 5 14 4 1 12 VALVE O. RANSTON RI USA A SSE 117 TYP TM U S.
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD TM-2020B, TM-2020B-LF
1 ASSE 117 3-1 F 8 5 1 TERMOSTATI 1 1 ASSE 117 1-1 F 8 3 5 1 TERMOSTATI 1 1 Bulletin G-11E August, 18 INSTALLATION ADJUSTMENT SERVIE IG-LOW MANIFOLD TM-B, TM-B-LF IMPORTANT! Provide serial numbers for
More informationINSTALLATION ADJUSTMENT SERVICE MEGATRON MODEL 8N-LF. Valve assemblies are ASSE 1017 listed
4 6 2 8 6 4 8 kg/cm 2 11 psi 1 1 6 1 1 4 1 4 6 4 1-1 6 3 8 14 6 1-1 4 5 1 1 6 3 8 14 4 5 1 1 TERMOSTATI 4 6 1-1 6 3 8 14 4 5 1 1 TERMOSTATI 4 6 1-1 6 3 8 14 4 5 1 1 4 6 1-1 LE ON ARD 6 3 8 14 4 5 1 1 EO-MIX
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD TM-2020B, TM-2020B-LF
2 4 1 11 7 8 2 3 4 5-1 F 14 1 12 2 4 1 ASSE 117 2 3 4 5-1 F 8 14 1 12 Bulletin G-11E April 214 INSTALLATION ADJUSTMENT SERVIE IG-LOW MANIFOLD TM-22B, TM-22B-LF IMPORTANT! Provide serial numbers for both
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD TM-2020B, TM-2020B-LF
2 1 ASSE 117 2 3-1 F 8 5 1 TERMOSTATI 1 12 2 ASSE 117 1 2 3-1 F 8 5 1 TERMOSTATI 1 12 Bulletin G-11E April 217 INSTALLATION ADJUSTMENT SERVIE IG-LOW MANIFOLD TM-22B, TM-22B-LF IMPORTANT! Provide serial
More informationINSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE TM-200 (NEW STYLE) TMS-200 (VALVE ONLY)
Bulletin G-2D-1 September 2008 INSTALLATION ADJUSTMENT SERVIE TERMOSTATI WATER MIXING VALVE TM-200 (NEW STYLE) TMS-200 (VALVE ONLY) IMPORTANT! This Bulletin covers valves built after June 2001, starting
More informationINSTALLATION ADJUSTMENT SERVICE NEXT-GENERATION MANIFOLD SYSTEMS TM-520B-LF, TM-820B-LF, TM-920B-LF, TM-1520B-LF
2 6 4 1 O. RANSTON RI USA TYP TM U S. Pat en ts 2. 97, 3, 6 1,1 95 3.15 2,76 8 2 3 R 4 5-1 6 F 14 1 12 Bulletin G-12 August, 218 INSTALLATION ADJUSTMENT SERVIE NEXT-GENERATION MANIFOLD SYSTEMS TM-52B-,
More informationDOMESTIC OUTLET. kg/cm 2 11 psi LEONARD LEONARD -10 C F LEONARD R THERMOSTATIC LEONARD LEONARD C F C F 60 COLD INLET HOT INLET
4 1-1 3 R 8 14 4 5 4 1 2 1 4 8 6 kg/cm 2 11 psi 8 1 1 1 14 1 4 ASSE 117 1-1 3 R 8 14 4 5 THERMOSTATI H 1 1 4 1-1 3 R 8 14 4 5 1 1 4 1-1 3 R 8 14 4 5 1 1 M-122Z September 1 MEGATRON MODEL 6N INSTALLATION
More informationLEONARD -10 LEONARD VALVE CO. CRANSTON RI USA. TYP TM US. P aten ts 2.970, 3,06 1, , " Maximum Operating Pressure 125PSI (8.6 Bar).
2 0 2 4 6 80 kg/cm psi 2 11 LEO NARD 8 10 1 10 0 1 TERMOSTATI 1 10 0-10 0 R F VALVE O. RANSTON RI USA TYP TM US. P aten ts 2.970, 3,06 1,195 3.152,76 0 30 80 1 50 100 1 Bulletin G18E May 08 INSTALLATION
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD SYSTEMS TM-520, TM-820, TM-920, TM-1520A TM-520-LF TM-820-LF, TM-920-LF, TM-1520A-LF
LEO ASSE R US. Patent 770 & 3,061,195 3.152,760 O. PE TM RAN STON R.I. Bulletin G11D April 2014 INSTALLATION ADJUSTMENT SERVIE HIGH-LOW MANIFOLD SYSTEMS TM-520, TM-820, TM-920, TM-1520A TM-520-LF TM-820-LF,
More informationOUTLET LEONARDH THERMOSTATIC INSTALLATION
Bulletin G-AT June 2012 INSTALLATION ADJUSTMENT SERVIE ALLTERNATIVE TEMPERATURE TERMOSTATI WATER MIXING VALVES TYPE TM-50-AT, 80-AT, 150-AT, 200-AT IMPORTANT! Provide valve serial number, (stamped on cover
More informationINSTALLATION ADJUSTMENT SERVICE TYPE TM-15, TM-20 (As furnished with models TM-554, TM-356, TM-356-W/HA, TM PRV, 8015, 12520, 15020)
OT BULLETIN P-15 June, 2006 INSTALLATION ADJUSTMENT SERVIE TYPE TM-15, TM-20 (As furnished with models TM-554, TM-356, TM-356-W/HA, TM-186-5015-PRV, 8015, 12520, 15020) IMPORTANT! Provide valve serial
More informationINSTALLATION SETUP AND OPERATING INSTRUCTIONS THERMOSTATIC WATER MIXING VALVE SYSTEMS TYPE *TM-600, TM-650, *TM-800, *TM-850, TM-5100, TM-5125
EMERGENY VALVE F EMERGENY VALVE INSTALLATION SETUP AND OPERATING INSTRUTIONS WATER SYSTEMS TYPE *TM-600, TM-650, *TM-800, *TM-850, TM-5100, TM-5125 IMPORTANT! Provide valve serial number, (stamped on valve
More informationHOT INLET COLD INLET INSTALLATION
EMERGENY VALVE F EMERGENY VALVE Bulletin G-4 INSTALLATION SETUP AND OPERATING INSTRUTIONS WATER SYSTEMS TYPE TM-600, TM-600-LF, TM-650, TM-800, TM-800-LF, TM-850, TM-850-LF TM-5100, TM-5100-LF, TM-5125,
More informationOUTLET LEONARD THERMOSTATIC INSTALLATION
BULLETIN G-2B-TMS August, 2018 INSTALLATION ADJUSTMENT SERVIE STEAM AND WATER MIXING VALVE TYPE TMS-25, 50, 80, 125, 150 IMPORTANT! Provide valve serial number (stamped on cover of valve) when ordering
More informationMEGATRON MODEL 2, 3, 4, and 5
MEGATRON MODEL 2, 3, 4, and 5 BULLETIN M-1020A 2/02 INSTALLATION ADJUSTMENT SERVICE COMPLETE WATER TEMPERATURE CONTROL STATION DOMESTIC OUTLET TEST/SETUP CONNETION RETURN LINE FROM BUILDING RETURN LINE
More informationMODEL 210, 210-LF THERMOSTATIC WATER MIXING VALVES INSTALLATION SETUP AND OPERATING INSTRUCTIONS
Bulletin G-210 January, 2014, 210-LF TERMOSTATI WATER MIXING VALVES INSTALLATION SETUP AND OPERATING INSTRUTIONS IMPORTANT! Provide valve serial number (begins with serial no. -1000) when ordering parts!!
More informationINSTALLATION ADJUSTMENT SERVICE TYPE TM-15, TM-20, TM-20-LF (As furnished with models TM-554, TM-356, TM-356-W/HA)
ASSE 1017 INSTALLATION ADJUSTMENT SERVICE TYPE TM-15, TM-20, TM-20-LF (As furnished with models TM-554, TM-356, TM-356-W/HA) BULLETIN P-15A January, 2014 IMPORTANT! Provide valve serial number when ordering
More informationOUTLET HOT INLET COLD INLET INSTALLATION
Bulletin G-29 December 2007 INSTALLATION ADJUSTMENT SERVICE TYPE TM-28 IMPORTANT! Provide valve serial number (stamped on cover of valve) when ordering parts!! Valve manufactured after July 2007 starting
More informationINSTALLATION SETUP AND OPERATING INSTRUCTIONS THERMOSTATIC WATER MIXING VALVE SYSTEM TM-500, TM-550
C BULLETIN G-6A January 2012 INSTALLATION SETUP AND OPERATING INSTRUCTIONS WATER SYSTEM TM-500, TM-550 IMPORTANT! Provide valve serial number (located on valve body) when ordering parts!! Starting with
More informationINSTALLATION ADJUSTMENT SERVICE
ASSE 1017 INSTALLATION ADJUSTMENT SERVICE TYPE TM-26, TM-26-LF BULLETIN G-26 January 2014 IMPORTANT! Provide valve serial number (stamped on cover of valve) when ordering parts!! Valve manufactured after
More informationINSTALLATION ADJUSTMENT SERVICE TYPE TM-15, TM-20* (As furnished with models TM-554, TM-356, TM-356-W/HA Valve is ASSE 1017 listed
ASSE 1017 INSTALLATION ADJUSTMENT SERVICE TYPE TM-15, TM-20* (As furnished with models TM-554, TM-356, TM-356-W/HA Valve is ASSE 1017 listed *Valve is CUPC listed IMPORTANT! Provide valve serial number
More informationINSTALLATION SETUP AND OPERATING INSTRUCTIONS THERMOSTATIC WATER MIXING VALVE SYSTEM * TM-500A, TM-550A
C ASSE 1017 BULLETIN G-6B March 2009 INSTALLATION SETUP AND OPERATING INSTRUCTIONS WATER SYSTEM * TM-500A, TM-550A IMPORTANT! Provide valve serial number (located on valve body) when ordering parts!! *ASSE
More informationInstallation, Operation and Maintenance Guide AP3900 Series Thermostatic Mixing Valves
Note: Please provide valve serial number (stamped on cover of valve) when ordering parts. Hot Water Tempered Water Outlet Cold Water Tempered Water Outlet Redundant Thermostatic Mixing Valve Hot Water
More informationMEGATRON MODEL 2NB-LF, 3NB-LF, 4NB-LF, 5NB-LF NEXT GENERATION MANIFOLD SYSTEMS TM-520B-LF, 820B-LF, 920B-LF, 1520B-LF
6 1-1 3 8 5 6 1 6 2 1 4 1 8 6 8 kg/cm2 11 psi 1 16 1 1 1 6 1 ASSE 117 VAL VE -1 CO. 3 6 8 5 1 THEMOSTATIC T YPE TM AN STON 1 1.I. U.S.A. 6 1-1 6 3 8 1 5 1 1 6 1-1 6 3 8 5 1 1 1 H C Bulletin M-115Z August,
More informationNote: Please provide valve serial number (stamped on cover of valve) when ordering parts. Tempered Water Outlet. Hot Water Inlet.
Note: Please provide valve serial number (stamped on cover of valve) when ordering parts. Tempered Water Outlet Angle Checkstop Angle Checkstop Hot Water Inlet G3700LF Cold Water Inlet Installation 1.
More informationMODEL TA. TA-SB 117.5mm mm HOT INLET. TA mm mm mm mm
WATER MIXER WATER MIXER TRERMOSTATIC WATER MIXER TRERMOSTATIC C TRERMOS TA TIC WA TER MIXER MODEL TA Bulletin P-7A-4 May 2011 (NEW STYLE) THERMOSTATIC WATER MIXING VALVES INSTALLATION SETUP AND OPERATING
More informationINSTALLATION ADJUSTMENT SERVICE
Bulletin XL-670 July 201 INSTALLATION ADJUSTMENT SERVICE HIGHLOW THERMOSTATIC WATER MIXING VALVE MODEL XL-670-LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!! ECO-MIX
More informationINSTALLATION ADJUSTMENT SERVICE HIGHLOW THERMOSTATIC WATER MIXING VALVE SERIES XL-32, XL-82
Bulletin XL-38 March 00 INSTALLATION ADJUSTMENT SERVICE HIGHLOW THERMOSTATIC WATER MIXING VALVE SERIES XL-3, XL-8 IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!!
More informationINSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE SERIES LV-981 & LV-982
Bulletin LV-98 March 010 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE SERIES & LV-98 IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!! ASSE 1017
More informationTA-300, TA-300-LF, TA-350, TA-350-LF
Bulletin G-5 INSTALLATION SETUP AND OPERATING INSTRUCTIONS EMERGENCY MIXING VALVE SYSTEM TA-300, TA-300-LF, TA-350, TA-350-LF IMPORTANT! Provide valve serial number (located on valve body) when ordering
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin 82 August, 208 INSTALLATION ADJUSTMENT SERVICE HIGHLOW THERMOSTATIC WATER MIXING VALVE SERIES, -LF,, -LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!!!
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin GLV-98 Old Rev. LV-98 February 1 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE SERIES, LV981-LF &, -LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD SYSTEMS TM-420A Valve assemblies are ASSE 1017 listed
4 2 AS SE 1 17 6 8 2 3 1 LEONAD 4 5-1 6 C F 14 1 12 4 2 1 17 6 8 2 3 1 LEONAD 4 5-1 6 C F 14 1 12 BULLETIN G-11F February 29 INSTALLATION ADJUSTMENT SEVICE HIGH-LOW MANIFOLD SYSTEMS TM-42A Valve assemblies
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin XL-150 February 2015 INSTALLATION ADJUSTMENT SERVICE HIGHLOW THERMOSTATIC WATER MIXING VALVE SERIES XL-150, XL-150-LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
. Bulletin XL-200 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE SERIES XL-200, XL-200-LF, XL-200-SW, XL-200-SW-LF IMPORTANT! Provide valve serial number, (located on valve cover) when
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin GLV-101 Old Rev. LV-101 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE SERIES LV-983, LV-983-LF & LV-984, LV-984 -LF IMPORTANT! Provide valve serial number, (located on valve
More informationINSTALLATION ADJUSTMENT SERVICE HIGH-LOW MANIFOLD SYSTEMS TM-420A Valve assemblies are ASSE 1017 listed
4 AS SE 1 17 6 1-1 3 LEONAD C F 6 8 14 4 5 1 1 4 1 17 6 1-1 F 3 LEONAD C 6 8 14 4 5 1 1 INSTALLATION ADJUSTMENT SEVICE HIGH-LOW MANIFOLD SYSTEMS TM-4A Valve assemblies are 117 listed Valve assemblies are
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin GLV-0 September 01 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE LV-0, LV-0-LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!! INSTALLATION
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin GLV-99 July, 01 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE LV-981A, LV-981A-LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!! INSTALLATION
More informationINSTALLATION 125 PSI (8.6 BAR) MAXIMUM OPERATING PRESSURE
Bulletin GLV- January 014 INSTALLATION ADJUSTMENT SERVICE THERMOSTATIC WATER MIXING VALVE LV-, LV--LF IMPORTANT! Provide valve serial number, (located on valve cover) when ordering parts!! INSTALLATION
More informationInstallation, Operation and Maintenance Guide G3600 Series Thermostatic Mixing Valves
Note: Please provide valve serial number (stamped on cover of valve) when ordering parts. Tempered Water Outlet Cold Water Thermometer Hot Water Inline Check Redundant Thermostatic Mixing Valve Angle Checkstops
More informationSS-7600 THERMOSTATIC MODEL INSTALLATION INSTRUCTIONS
LEONARD SS-7600 THERMOSTATIC MODEL ½ top inlets Valve is ASSE 06 Listed INSTALLATION INSTRUCTIONS Bulletin 7600-SS March 06 SHOWER HEAD O'RING (TM-6B) 6 8 0 HOT COLD 7 9. Remove item (), - #/-0 X / long
More informationNote: Please provide valve serial number (stamped on cover of valve) when ordering parts. Thermometer. Hot Water Inlet. Cold Water Inlet G3600LF
Note: Please provide valve serial number (stamped on cover of valve) when ordering parts. Thermometer 1/2" OD Copper Tube Inlets Hot Water Inlet Cold Water Inlet G3600LF Installation 1. Install valve in
More information30 R -10 C F H C INSTALLATION. Maximum Operating Pressure 125PSI (860 KPA) for Hot and Cold Water. CAUTION
ASSE 117 1-1 2 6 3 4 5 4 1-1 2 6 3 4 5 BULLETIN G-26-34 January 216 INSTALLATION ADJUSTMENT SEVICE TYPE TM-26-F-DT-34, TM-26-LF-F-DT-34 IMPOTANT! Provide valve serial number (stamped on cover of valve)
More informationMEGATRON MODEL 2N, 3N, 4N, 5N HIGH-LOW MANIFOLD SYSTEMS TM-520, TM-820, TM-920, TM-1520A TM-520-LF, TM-820-LF, TM-920-LF, TM-1520A-LF
5-1 8 1 1 2 4 8 6 8 kg/cm 2 11 psi 1 1 1 LEO NAD 17 VAL VE - C O. THEMOSTATIC PE TM 8 5 1 CAN STON 1.I. U.S.A. - 8 1 5 1-8 5 1 1 H C Bulletin M-11Z January 14 MEGATON MODEL 2N, 3N, 4N, 5N HIGH-LOW MANIFOLD
More informationMEGATRON MODEL TA, TA-LF
6 1-1 2 LEONAD 6 3 8 6 C H LEONAD 116 LEONAD VALVE CO. CANSTON I 291 8 2 3 1 LEONAD -1 6 MODEL 21 Water Mixer 117 1 6-1 2 3 LEONAD 6 8 6 8 2 3 1 LEONAD -1 6 MEGATON MODEL TA, TA-LF Bulletin G-1L August,
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION MEGATRON MODEL 10NB-LF 4 HOT & COLD INLETS 4 MIXED OUTLET 2 RETURN PIPING
4 4 5-4 3 8 4 4 5-3 8 4 TERMOSTATI 4 3 4 5-8 4 TERMO STATI TERMOSTATI 4 4 5-3 8 4 4-3 8 4 4 5 OMPLETE WATER TEMPERATURE ONTROL STATION EO-MIX Valve assemblies are ASSE 7 listed Submittal S-596Z-LF August,
More informationMODEL 270-LF ECO-MIX THERMOSTATIC MIXING LEAD FREE THERMOSTATIC POINT OF USE MIXING VALVE. Submittal Data Sheet S-827-LF February 2013
TERMOSTATI MIXING VALVE 5-1/2" 140mm EO-MIX Submittal Data Sheet S-827-LF February 2013 MODEL 270-LF LEAD FREE TERMOSTATI POINT OF USE MIXING VALVE MODEL ½ inlets, ½ outlet, (MIPS connections) MATERIALS:
More informationCLASSIC HIGH LOW MANIFOLD SYSTEMS
LASSI HIGH LOW MANIOLD SYSTEMS LEONARD LASSI HIGH LOW MANIOLD SYSTEMS control water temperature for domestic hot water systems, shower rooms and other commercial, institutional and industrial applications
More informationCOMPLETE WATER TEMPERATURE CONTROL SYSTEM
OMPLETE WATE TEMPEATUE ONTOL SYSTEM MEGATON omplete Water Temperature ontrol Systems regulate water temperature for building hot water systems and other commercial, institutional and industrial applications.
More informationInstallation S
Installation S59-2025 Thermostatic Mixing Valve (TMV25) with Optional Cabinet S59-2025RE (with Recess-Mounted Enamel Cabinet) S59-2025RS (with Recess-Mounted Stainless Steel Cabinet) S59-2025SE (with Surface-Mounted
More informationInstallation S
Installation S59-3080 Thermostatic Mixing Valve with Optional Cabinet S59-3080RE (with Recess-Mounted Enamel Cabinet) S59-3080RS (with Recess-Mounted Stainless Steel Cabinet) S59-3080SE (with Surface-
More informationInstallation S
Installation S59-3080 Thermostatic High-Low Mixing Valve (HL80) with Optional Cabinet S59-3080RE (with Recess-Mounted Enamel Cabinet) S59-3080RS (with Recess-Mounted Stainless Steel Cabinet) S59-3080SE
More informationInstallation S
Installation S59-3045 Thermostatic High-Low Mixing Valve (HL45) with Optional Cabinet S59-3045 (Valve Only) S59-3045RE (with Recess-Mounted Enamel Cabinet) S59-3045RS (with Recess-Mounted Stainless Steel
More informationInstallation S
Installation S59-3200 Thermostatic Mixing Valve (HL200) with Optional Cabinet S59-3200RE (with Recess-Mounted Enamel Cabinet) S59-3200RS (with Recess-Mounted Stainless Steel Cabinet) S59-3200SE (with Surface-Mounted
More informationInstallation S HL2X2 High Capacity Manifold System. Table of Contents Rev. B; ECN Bradley Page 1 of 8 11/10/2014
Installation S59-3400 HL2X2 High Capacity Manifold System Table of Contents Supplies Required... 3 Rough-Ins... 3 Connect Supply Lines and Install Thermometer... 4 Adjust Temperature and Test Unit... 5
More informationNEW GENERATION HIGH LOW SYSTEMS
NEW GENEATION HIGH LOW SYSTEMS NEW GENEATION TM-52-DT HIGH LOW SYSTEMS control water temperature for domestic hot water systems, shower rooms and other commercial, institutional and industrial applications
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION
- 3 5 ps i kg/cm ASSE 7 VAL VE - CO. 3 5 THEMOSTATIC TYPE TM US. Patent 77 & 3,,95 3.5,7.I. - 3 5-3 5 Submittal Data Sheet S-533Z-LF April, COMPLETE WATE TEMPEATUE CONTOL STATION ECO-MIX MEGATON LEAD FEE
More informationTMV45 & TMV80 Standard Thermostatic Mixing Valves
Reliable liquid-filled thermostat Integral strainer checkstops on inlets Adjustable set point within temperature range Accurate temperature control Positive shutoff of hot supply when cold supply is lost
More informationInstallation Instructions / Warranty. Metris 31060XX XX XX1
Installation Instructions / Warranty Metris 31060XX1 31020XX1 31261XX1 Metris Single Control Lavatory Mixer 31060XX1 Tall Lavatory Mixer 31020XX1 Single Control Bidet Mixer 31261XX1 31060XX1 31020XX1 31261XX1
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION
- 3 5 kg/cm C AS SE 7-3 5 THEMOSTATIC H - 3 5 3 5 - COMPLETE WATE TEMPEATUE CONTOL STATION ECO-MIX Submittal Data Sheet S-5Z-LF August, MEGATON LEAD FEE MODEL NB-LF HOT & COLD INLETS MIXED OUTLET ¼ ETUN
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION
- 3 5 kg/cm ASSE 7 - CO. 3 5 THEMOSTATIC TYPE TM US. Patent 77 & 3,,95 3.5,7.I. - 3 5-3 5 COMPLETE WATE TEMPEATUE CONTOL STATION ECO-MIX Submittal Data Sheet S-5Z-LF August, MEGATON LEAD FEE MODEL 3NB-LF
More informationAM Series Proportional Thermostatic Mixing Valve
AM-1 1070 Series Proportional Thermostatic Mixing Valve PATENTED, WIT DUAL ASSE 1070 AND 1017 ERTIFIATION, IAPMO AND SA LISTING IN ONE VALVE PRODUT DATA PRODUT INFORMATION SPEIFIATIONS Media Temperature
More informationInstallation Instructions / Warranty
Installation Instructions / Warranty Metris 31063XX1 Metris 31263XX1 Talis 32310XX1 Focus 31730001 Metris Widespread Lavatory Faucet Metris Widespread Bidet Faucet Talis S Widespread Lavatory Faucet Focus
More informationInstallation Instructions / Warranty
Installation Instructions / Warranty IP C 04210000 04211000 04212000 IP S 04203000 04204000 04205000 IP E 04199000 04200000 04201000 IP Trim Sets Valve trim only IP C 04212000 IP E 04201000 IP S 04205000
More information1. Connect Hose Attach a garden hose to the swivel nut hose fitting.
INSTRUCTIONS Congratulations on purchasing the BLASTER 1000 TM Automatic Filter Cleaner. Cleaning your dirty pool filter will now be a whole lot easier. Taking just a few minutes, the BLASTER 1000 TM will
More informationInstallation Instructions / Warranty. Starck 10111XX XX XX1
Installation Instructions / Warranty Starck 10111XX1 10120XX1 10211XX1 90502203 1/2005 Starck single control lavatory faucet 10111XX1 Starck tall single control lavatory faucet 10120XX1 Starck single control
More informationInstruction Manual. Cheese Warmer with Pump
Instruction Manual Cheese Warmer with Pump 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2013 Gold Medal Products Co. Part No. 38298 SAFETY PRECAUTIONS Page 2 INSTALLATION INSTRUCTIONS Inspection
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION
- 5 kg/cm 7 7-5 - 5-5 Submittal Data Sheet S-5Z-LF April, COMPLETE WATE TEMPEATUE CONTOL STATION ECO-MIX MEGATON LEAD FEE MODEL NB-LF ¾ HOT & COLD INLETS MIXED OUTLET ¾ ETUN PIPING. to GPM(.7 to 7 l/min)
More informationHL45, HL80 Thermostatic High-Low Valves
Lead-Free Brass Design Reliable Liquid-Filled Thermostat with 10 year warranty Integral Strainer Checkstops on Inlets Adjustable Set Point within Temperature Range Accurate Temperature Control to within
More informationTWIN-FLOIII HEATER INSPECT THE SHIPMENT IMMEDIATELY WHEN RECEIVED TO DETERMINE IF ANY DAMAGE HAS OCCURRED DURING SHIPMENT.
TFII-11 Beacon/Morris TWIN-FLOIII HEATER INSTALLATION INSTRUCTIONS TYPES K, W, & F ATTENTION: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE, OR SERVICE THE BEACON MORRIS TWIN-FLO
More informationCooler Mounted Bottle Fillers
BF Series Bottle Filler, Sensor Operated TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:.800.9.960 Technical Assistance Fax:.66.8.89 NOTES TO INSTALLER:. Please leave this documentation with the owner
More informationA152.8 Series Barrier Free, Bi-Level, Wall Mounted Drinking Fountain
Series Barrier Free, Bi-Level, Wall Mounted Drinking Fountain A52408S / A52408S-SO TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:.800.59.9360 Technical Assistance Fax:.626.855.4894 NOTES TO INSTALLER:.
More informationInstallation S IMPORTANT! Bradley Thermostatic Mixing Valve for Individual Showers. Table of Contents
Installation S59-2006 Bradley Thermostatic Mixing Valve for Individual Showers Table of Contents Supplies Required................. 2 Installation Instructions.............. 2 Valve Adjustments.................
More informationINSTALLATION, OPERATION AND MAINTENANCE
INLINE HEATER INSTALLATION, OPERATION AND MAINTENANCE MODELS: ILS SERIES 1.5kW 120V SINGLE PHASE BEFORE YOU BEGIN CHECK ALL ELECTRICAL CONNECTIONS TO ALL COMPONENTS WITHIN THE HEATER FOR TIGHTNESS. CONNECTIONS
More informationInstallation Manual. Models 99168, 99169, 99170
Wet-Rated Globe Fitter Installation Manual Compatible with: 2xxxx Types A - Z 51000-58999 fan series 59500-59999 fan series Select Casablanca Fans Models 99168, 99169, 99170 BEFORE YOU BEGIN Read entire
More informationInstallation Instructions
IMPORTANT Installation and final temperature adjustment are the responsibility of the installer. Installation Instructions Thermostatic Mixing Valve for Sinks/Faucets Inlet Outlet Model Connection Connection
More informationCOMPRESSED AIR DRYER. SAFETY... Page 2 MAINTENANCE... Page 5. INSTALLATION... Page 3 PARTS AND KITS... Page 6
OWNERS MANUAL BOSS COMPRESSED AIR DRYER Distributed by Air & Vacuum Process, Inc. Phone: 281-866-9700 Fax: 281-866-9717 Email: sales@airvacuumprocess.com SAFETY... Page 2 MAINTENANCE... Page 5 INSTALLATION...
More informationSubmittal S-NV-150-LF-M November, 2018 MEGATRON MODEL NV-150-LF DIGITAL TEMPERATURE CONTROL STATION
! APPROXIMATE DIMENSIONS A = 3-3 B = 3-10-1/2 C = 4 D = 9-1/2 *Image not to scale* WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer.
More informationECO-MIX COMPLETE WATER TEMPERATURE CONTROL STATION
1-1 3 1 5 1 kg/cm 11 1 1 1 1 1 1-1 3 1 5 1 1-1 3 1 5 1 1-1 3 5 1 COMPLETE WATE TEMPEATUE CONTOL STATION ECO-MIX Valve is ASSE 117 Certified Submittal S-11-1-LF August, 1 MEGATON LEAD FEE MODEL XLLF 1 HOT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 5000 700069 50055 MODEL: Dillon 5000 (RH-600) 50055 (RH-600X) 700069 (TRRH-600) REV D Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size
More informationWATER TEMPERATURE CONTROL SYSTEMS
Mixing Safety & Performance for Over 100 Years WATER TEMPERATURE CONTROL SYSTEMS TM-2020B-LF-DT TM-2020B-2PS-LF MEGATRON 6NB-LF ASSE 1017 LOW LEAD CERTIFIED Made in the USA with Domestic and Imported Parts
More information1. Connect Hose Attach a garden hose to the swivel nut hose fitting.
INSTRUCTIONS Congratulations on purchasing the BLASTER 1000 TM Automatic Filter Cleaner. Cleaning your dirty pool filter will now be a whole lot easier. Taking just a few minutes, the BLASTER 1000 TM will
More informationFFP S700 SERIES. Pull-Out Spray Faucet. Installation guide
FFP S700 SERIES Pull-Out Spray Faucet Installation guide G 1782 G 1748.XX G 29016 G 1156 G R0239.XX G 13396.XX G R0637 G R1664 G 1636 G 1463 TECHNICAL DATA Minimum working pressure 0,5 bar Maximum working
More informationA112408B/S-VR-UBL TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: Technical Assistance Fax:
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Vandal Resistant Refrigerated Universal Bi-Level AquaAccess Barrier Free, Wall Mounted Water Cooler OR Alternate Configuration A112408B/S-VR-UBL TECHNICAL
More informationInstallation Instructions / Warranty
Installation Instructions / Warranty Citterio M 34133XX1 Citterio M 34213XX1 Axor Citterio M widespread lavatory faucet 34133XX1 Axor Citterio M widespread bidet faucet 34213XX1 34213XX1 34133XX1 Technical
More informationSubmittal S-NV-200-LF-M DIGITAL TEMPERATURE CONTROL STATION. Valve assembly is ASSE 1017 Certified. Valve assembly is cupc Certified
! APPROXIMATE DIMENSIONS A = 3-11 B = 3-9 C = 4-1/2 D = 1-1 *Image not to scale* WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer.
More informationModel H1011.8/H1011.8HPS Water Cooler
455 Kleppe Lane Sparks, NV 8943-6467 (775) 359-472 Fax (775) 359-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model H0.8/H0.8HPS Water Cooler INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
More informationA910.8A Remote Water Chiller, 8 GPH A A / A A-220V TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
Remote Water Chiller, 8 GPH A9100080-A / A9100080-A-220V TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: 1.800.591.9360 Technical Assistance Fax: 1.626.855.4894 NOTES TO INSTALLER: 1. Please leave this
More informationINSTALLATION INSTRUCTIONS. Cubix Widespread Faucet Part #: 3204, 5204, 3304, 5304 HANDLE STYLES
INSTALLATION INSTRUCTIONS Cubix Widespread Faucet Part #: 04, 04, 04, 04 Confidence from start to finish. HANDLE STYLES 04 04 jaclo industries Dermody Street Cranford, NJ 001 p 0..44 00..0 f 0..11 00..4..1
More information52 SAN LUCAS CEILING FAN
52 SAN LUCAS CEILING FAN Owner s Manual Models #20551 If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9 a.m.-
More informationInstallation & Operation Manual
Installation & Operation Manual Table of Contents Pre-Installation Information...2 Physical Dimensions...4 Rough-In Dimensions...5 Hardware Identification Chart...6 Installation Instructions...7 Step 1:
More informationInstruction Manual. Astro Staging Cabinet
Instruction Manual Astro Staging Cabinet 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2017 Gold Medal Products Co. Part No. 40269 SAFETY PRECAUTIONS DANGER Machine must be properly grounded to
More informationSeries 1140 and 1141 Temperature Regulators
Hoffman Specialty Installation & Maintenance Instructions HS-504(E) Series 1140 and 1141 Temperature Regulators! CAUTION FOLLOW ALL INSTALLATION AND OPERATING INSTRUCTIONS. TURN OFF WATER OR STEAM BEFORE
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS AquaArctic Remote Water Chiller A9100080 -A TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: 1.800.591.9360 Technical Assistance Fax: 1.626.855.4894
More informationInstallation Instructions / Warranty. Massaud
Installation Instructions / Warranty Massaud 18450001 Axor Massaud Free-Standing Tub Filler 18450001 Technical Information Max. incoming water pressure 145 psi Recommended water pressure 14.5-72 psi Max.
More information