Hot Melt Material Applicator MC 12 / MC 24
|
|
- Kory Dickerson
- 5 years ago
- Views:
Transcription
1 Hot Melt Material Applicator Manual P/N D English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY
2 Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected by copyright. Original copyright date No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Nordson Corporation. The information contained in this publication is subject to change without notice. Trademarks AccuJet, AquaGuard, Asymtek, Automove, Autotech, Blue Box, CF, CanWorks, Century, Clean Coat, CleanSleeve, CleanSpray, Compumelt, Control Coat, Cross-Cut, Cyclo-Kinetic, Dispensejet, DispenseMate, Durafiber, Durasystem, Easy Coat, Easymove Plus, Econo-Coat, EPREG, ETI, Excel 2000, Flex-O-Coat, FlexiCoat, Flexi-Spray, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Helix, Horizon, Hose Mole, Hot Shot, Hot Stitch, Isocoil, Isocore, Iso-Flo, JR, KB30, Little Squirt, Magnastatic, MEG, Meltex, MicroSet, Millenium, Mini Squirt, Moist-Cure, Mountaingate, MultiScan, Nordson, OmniScan, Opticoat, Package of Values, Pattern View, PluraFoam, Porous Coat, PowderGrid, Powderware, Pro-Flo, ProLink, Pro-Meter, Pro-Stream, PRX, RBX, Rhino, S. design stylized, Saturn, SC5, Select Charge, Select Coat, Select Cure, Slautterback, Smart-Coat, Spray Squirt, Spraymelt, Super Squirt, Sure Coat, System Sentry, Tela-Therm, Trends, Tribomatic, UniScan, UpTime, Veritec, Versa-Coat, Versa-Screen, Versa-Spray, Watermark, When you expect more. are registered trademarks of Nordson Corporation. ATS, Aerocharge, Auto-Flo, AutoScan, BetterBook, Chameleon, CanNeck, Check Mate, COLORMAX, Control Weave, Controlled Fiberization, CPX, E-Nordson, EasyClean, Eclipse, Equi=Bead, Fillmaster, Gluie, Ink-Dot, Iso-Flex, Kinetix, Maxima, MicroFin, Minimeter, Multifil, OptiMix, PluraMix, Primarc, Prism, Process Sentry, PurTech, Pulse Spray, Seal Sentry, Select Series, Sensomatic, Shaftshield, Spectral, Spectrum, Sure Brand, Swirl Coat, Vista, Walcom, 2 Rings (Design) are trademarks of Nordson Corporation. Designations and trademarks stated in this document may be brands that, when used by third parties for their own purposes, could lead to violation of the owners rights. COV_EN_403076D 2002 Nordson Corporation
3 Table of Contents I Table of Contents Section 1 Safety Separate document Section 2 Description 1. Intended Use Area of Use (EMC) Use Limitation Unintended Use Examples Residual Risks Operating Manual Series Overview Explanation of Unit Description Configuration Code Example Code and Keys Unit Components Options Functioning Melting Process and Hot Melt Material Supply Motor Gear Pump Shutoff Valve (Option) Mechanical Safety Valve (Standard) Pneumatic Safety Valve (Option) Level Control (Option) Heated Can Receptacle (Option for MC 12) Bar Graph (Option) Heating and Temperature Control Undertemperature Locking Device Overtemperature indication / shutdown Temperature Setback Inert Gas Equipment Nordson Corporation
4 II Table of Contents Section 2 Description (contd.) 9. Electrical Cabinet Front/Rear Side Pulling the Electrical Cabinet Forward Main Switch Turning Unit On Control System Channel Assignment for MC xx without Heated Can Receptacle Channel Assignment for MC 12 with Heated Can Receptacle Indicator Light Button Heating On/Off Button Purge Lighted Symbol Inert Gas Bottle Empty Lighted Symbol Inert Gas Supply Programmable Week Timer (Option) Electrical Cabinet Aeration Tach Generator Connection Socket XS 2 Interface Door Locks Protective Panels ID Plate Section 3 Installation 1. Transport Lifting (Unpacked Unit) Unpacking Removing Storage Disposal Setting Up Overview Mounting Indicator Light Exhausting Hot Melt Material Vapors Nordson Corporation
5 Table of Contents III Section 3 Installation (contd.) 10. Electrical Connections Laying Cables Line Voltage Tach Generator (Accessories) XS 2 Interface Installing Heated Hoses Connecting Disconnecting Relieving Pressure Second Open jawed Wrench Pneumatic Safety Valve (Option) Inert Gas Equipment Section 4 Operation 1. Filling the Tank Maximum Filling Level Tank with Optional Can Receptacle Opening and Closing Tank Opening tank Closing tank Tank Hood Switch Setting Temperatures General Values Setting Hot Melt Material Feed Quantity Motor/Pump Speeds Manual Operation Automatic Operation Initial Startup Daily Switch ON/OFF Daily Switch ON Daily Switch OFF (Inert Gas also Off) Daily Switch OFF (Inert Gas not Off) Emergency Switch OFF Settings Record Form Nordson Corporation
6 IV Table of Contents Section 5 Maintenance 1. Relieving Pressure Daily Maintenance Regular Maintenance External Cleaning Inspection for External Damage Electrical Cabinet Fan Maintenance Changing Hot Melt Material Type Flushing with a Cleaning Agent Maintenance Record Form Section 6 Troubleshooting 1. Control System Helpful Tips Indication Lamps and Indicator Light Troubleshooting Tables Only the White Indication Lamp is Lit Red Indication Lamp is Lit Unit does not Function One Channel (Heating Zone) does not Heat No Pilot Voltage No Hot Melt Material (Motor does not Rotate) No Hot Melt Material (Motor Rotating) Incorrect Motor Rotation in Automatic Operation Not Enough Hot Melt Material Hot Melt Material Pressure Too High Hot Melt Material Pressure Too Low Hot Melt Material Residues in Tank Hot Melt Material Hardens in Tank Section 7 Specifications 1. General Data Temperature Electrical Data Dimensions and Weights Section 8 Index Nordson Corporation
7 Section 1 Safety Observe and follow all safety instructions, the general safety instructions included as a separate document, as well as the specific safety instructions in all other related documentation Nordson Corporation
8 1-0 Safety 2002 Nordson Corporation
9 Section 2 Description 2002 Nordson Corporation
10 2-0 Description 2002 Nordson Corporation
11 Description 2-1 Section 2 Description 1. Intended Use Hot melt material applicators of the series MC 12 and MC 24 may only be used to melt and process polyurethane hot melt materials (PUR). Any other use is considered as not intended and is carried out at the operator s own risk. Nordson will not be responsible for personal or equipment damage resulting from unintended use. Intended use also includes the observance of Nordson safety instructions. Nordson recommends collecting detailed information about the materials to be used. Area of Use (EMC) The units are designed for use in industrial areas (see also included Declaration of Conformity). Use Limitation When used in residential and commercial areas, the units can cause interference in other appliances, e.g. radios. Unintended Use Examples The unit may not be used under the following conditions: In defective condition When unapproved changes or modifications have been made by the customer Without heat protection and protective panels With electrical cabinet door open With tank lid open With tank hood open In an explosive atmosphere When the values stated under Specifications are not complied with. The unit may not be used to melt and process the following materials: Explosive and flammable materials Erosive and corrosive materials Foodstuffs 2002 Nordson Corporation
12 2-2 Description 2. Residual Risks The unit is designed to protect operating personnel from possible risks. However, some residual risks cannot be avoided. Personnel must consider the following: Risk of burns from hot melt material Risk of burns on the tank lid after the tank hood has been opened Risk of burns when filling the tank Risk of burns from heated accessories such as heated hoses or hot melt application heads. Inhalation of potentially hazardous hot melt material vapors. 3. Operating Manual As an exampel for all units of series MC 12 and MC 24 the hot melt material applicator MC 12-1x1 will be described. The position numbers in the illustrations do not correspond to the position numbers in the technical drawings or spare parts lists. The safety valve is also referred to as bypass or bypass valve in Nordson manuals. The indicator light and the inert gas equipment, in the index sometimes referred to as an option, belongs as a standard equipment to this unit. 4. Series Overview Unit Motor(s) / Pump(s) Hose connections per pump MC 12-1x1 1 1 MC 12-1x2 1 2 MC 12-2x1 2 1 MC 24-1x1 1 1 MC 24-1x2 1 2 MC 24-2x1 2 1 MC 24-2x2 2 2 Explanation of Unit Description The description is illustrated by the example MC 12-1x1. MC 12-1x1 1 Hose connection per pump 1 Motor / pump Description of the series / 12 liter tank capacity Description Nordson units of the Meltex product line which process polyurethane hot melt material. M = Moisture C = Curing 2002 Nordson Corporation
13 Description Configuration Code The configuration code is stamped into the ID plate. The code consists of all positions, whereby a function or component that is not available is replaced with an X (Refer to Example). Example Unit designation Configuration Options Position Code M C x 1 A A A 1 / X X X X T C X K X X X Code and Keys The chart shows all possible configurations. Unit des sign nation Co onfig gura ratio on Op ption ons Position Code Key Note 1 M Series or unit designation M = Moisture 2 C Series or unit designation C = Curing 3 1 / 2 Series or unit designation 12 = 12 liter tank capacity 24 = 24 liter tank capacity 4 2 / 4 Series or unit designation One pump 2 Two pumps 7 x 8 1 One hose connection per pump 2 Two hose connections per pump Available only for MC 24 when two pumps are used 9 G Operating voltage 3x230 V AC Temperature sensor Fe-CuNi Fe-CuNi = FE/KO C Operating voltage 3x400 V AC Temperature sensor Fe-CuNi (FE/KO) Fe-CuNi = FE/KO Y Operating voltage 3x230 V AC Temperature sensor Ni 120 V Operating voltage 3x400 V AC Temperature sensor Ni A Pump PR 2m1 with VX-non-stick coating 11 C Pump PR 4m1 with VX-non-stick coating D Pump PR 6m1 with VX-non-stick coating Standard with 2-pump units E Pump PR 12m1 with VX-non-stick coating F Pump PR 12m2 with VX-non-stick coating Standard with 1-pump units G Pump PR 25m2 with VX-non-stick coating 12 1 Hose connection 5 / 16 in. = 8 mm 2 Hose connection 5 / 8 in. = 16 mm 3 Hose connection 1 / 2 in. = 13 mm 13 / 14 B Bar graph See control system 15 F Shutoff valve See fig P Pneumatic safety valve See fig M Pressure indicator with sensor See fig T Programmable week timer See fig C Level control See fig A Additional heating channels for one hose / application head B Additional heating channels for two hoses / application heads 21 K Heated can receptacle Available only for MC X 23 X 24 S Special equipment 2002 Nordson Corporation
14 2-4 Description 6. Unit Components Figure A 2 1 shows the essential unit components. Details can be found in the technical drawings (Refer to Spare Parts Lists) Á MCSY351L168B0697 Fig Indicator light 2. Electrical cabinet 3. Motor cover 4. Motor 5. Actual value speed monitoring 6. Coupling 7. Gear pump 8. Inert gas equipment 9. Adhesive drain flange 10. Heat protection 11. Tank Feet 14. Flap 15. Hose connection fitting 16. Hose connection socket 17. Tank lid handle 18. Tank lid 19. Tank lid lock 20. Tank hood bracket 21. Tank hood switch 22. Tank hood 23. Tank hood handle Safety valve (35 bar) 27. Protective panels 28. Unit frame 29. ID plate 30. Tank lid detent 2002 Nordson Corporation
15 Description Options Figure 2-2 shows possible options AUTO Fig Level control: Switch amplifier / indicator light (yellow) 2. Pneumatic safety valve 3. Shut off valve 4. Week timer 5. Bar graph MCSY356L168B Pressure sensor 7. Can receptacle (only for MC 12) 2002 Nordson Corporation
16 2-6 Description 8. Functioning The functioning of the unit is described here. The operation of the individual components is described in the manual for the component (refer to Index of Documentation). Melting Process and Hot Melt Material Supply The adhesive is placed in the tank. There it is heated to the processing temperature stated by the manufacturer or to the temperature set by the user. The melted material flows to the gear pump. The gear pump driven by a motor feeds the material to the hose connection fitting. From here the material flows through the heated hose to the hot melt material application head or to the hot melt material handgun. Motor See also manual Motor. The electronically controlled motor drives the gear pump. The motor speed is indicated on a display. To set speed see manual Control System. NOTE: The motor is only then ready for operation when the undertemperature locking device has been released or when the unit has almost reached the set nominal value temperature. NOTE: Avoid a permanent motor/pump speed of less than 5 RPM and more than 80 RPM to prevent excessive wear. Gear Pump See also manual Gear Pump. The gear pump is driven by a motor and feeds the hot melt material to the hose connection fitting. The size and speed of the gear pump determine the material feed quantity. NOTE: Nordson gear pumps may not be operated without hot melt material. Before switching on the motor, make sure the tank is filled. NOTE: Avoid a permanent motor/pump speed of less than 5 RPM and more than 80 RPM to prevent excessive wear. Shut off Valve (Option) Fig XXSY036S050A0595 The shut off valve is located in the safety valve plate which is between the tank and gear pump. It serves to block the flow of hot melt material when the gear pump is to be replaced. It is activated with a hex spanner. Position 1: shutoff valve open Position 2: shutoff valve closed Nordson Corporation
17 Description 2-7 Mechanical Safety Valve (Standard) See also manual Safety Valve. The mechanical safety valve limits the hot melt material pressure produced by the gear pump and keeps it constant. It is factory set and lead sealed. When the factory set pressure is exceeded, the safety valve opens and the hot melt material circulates inside the safety valve plate. Pneumatic Safety Valve (Option) See also manual Safety Valve. The pneumatic safety valve has the same safety function as the mechanical safety valve. In addition, it offers the possibility to set the hot melt material pressure to a certain value or to control it dependant on the parent machine speed. Level Control (Option) See also manual Switch Amplifier CSV with Level Sensor. For level control purposes, two capacitive sensors are built into the wall of the tank and electrically connected to a switch amplifier. The lower tank level is shown by the indicator light (yellow). The potential free relay outputs Indication Fill and Indication Full (Interface XS 2) can be used e.g. to activate external signal transducers. Heated Can Receptacle (Option for MC 12) The heated can receptacle is built into the upper part of the tank and can accomodate 2.5 kg cans with a diameter up to 144 mm and height of up to 180 mm. The temperature of the can receptacle and the tank is controlled through separate heating channels. Bar Graph (Option) See also manual Control System. The bar graph simultaneously shows the range in which the temperature is for all channels that are switched on Nordson Corporation
18 2-8 Description Heating and Temperature Control The melting zone is heated with cast in heating elements. They provide optimal heat conduction and energy utilization. The temperature is measured by sensors and regulated electronically by the temperature controller. Undertemperature Locking Device The undertemperature locking device prevents the unit or system from starting up when the hot melt material is too cold. It is activated until the nominal temperature value minus undertemperature value has been exceeded. On initial heating of the unit, the locking device is first released when the actual temperature is 3 C below the nominal value temperature. The undertemperature locking device locks the motors, solenoid valves and, in some cases, other components of the hot melt material application system. Refer to the Wiring Diagram to determine which components are locked. Overtemperature indication / shutdown The independently operating overtemperature shutdown mechanisms protect the unit and adhesive from overheating. For overtemperature shutdown, the heating and motor are switched off. The red indication lamp collective fault lights up. Overtemperature indication through temperature controller: Switches relay output collective fault when setpoint temperature value plus overtemperature value has been reached and the red indication lamp lights up. The unit remains ready for operation. Overtemperature shutdown through temperature controller: The overtemperature shutdown value is set automatically 30 C above the highest temperature setpoint value. NOTE: Depending on the adhesive used, the overtemperature thermostats of the tank and possibly of the optional can receptacle may need to be adapted to the maximum processing temperature of the adhesive (This may mean that the overtemperature thermostats have need to be replaced). However, the switchoff value of the thermostat may not exceed the max. operating temperature of the unit! For thermostats see section Specifications. WARNING: When the overtemperature shutdown is triggered, there is either a fault in settings or unit malfunction. Switch off the unit and have the fault eliminated by qualified personnel. Temperature Setback Serves to protect the hot melt material and save energy during interruptions in production or work stoppages. Setback value and setback period are adjustable Nordson Corporation
19 Description 2-9 Inert Gas Equipment See also manual Inert Gas Equipment and manual Control System, Operation of the Motor Section, Parameter Con, CoF and C1. NOTE: The parameters Co OFF and Co On (inert gas equipment) described in the manual Control System, section Operation of Temperature Part are not part of this system. CAUTION: Use only suitable inert gas. Refer to the Material Safety Data Sheet of the material or contact the material supplier. The inert gas prevents the material in the tank from reacting with humidity. It displaces the air in the tank and thus protects the material from an undesired reaction which may cause the material to harden sooner than it should. Inert gases are e.g. nitrogen (N) and carbon dioxide (CO 2 ). The advantage of carbon dioxide is that it is heavier than air and literally floats on top of the material in the tank. NOTE: A diaphragm compressed air dryer, including preceding high performance compressed air filter, for conditioning compressed air such that it can be used as inert gas, can be purchased from Nordson. The inert gas supply is carried out: Automatically during operation as set on the Control System (inert gas injection interval and duration of injection). Automatically after the tank hood is closed. The duration of injection can be set (Parameter C1). Manually by pressing the Purge button as an additional Inert gas flush, e.g. when the tank has been filled. When the inert gas pressure is too low, the illuminated symbol Inert gas bottle empty lights up. In addition, a potential free contact for connection of external indication devices is available (XS 2 Interface). CAUTION: When the main switch is set to 0/OFF, the inert gas equipment is turned off and the tank is deaerated. This can lead to hardening of the adhesive in the tank (Also refer to Daily Shutdown) Nordson Corporation
20 2-10 Description 9. Electrical Cabinet WARNING: Risk of electric shock. Failure to observe can result in personal injury, death and/or equipment damage. Front/Rear Side AUTO 8 13 MCPA041L143B1198 Fig Indicator light 2. Control system 3. Button Heating off 4. Button Heating on 5. Lighted symbol Inert gas supply 6. Button Purge (Inert gas flush) 7. Lighted symbol Inert gas bottle empty 8. Programmable week timer (Option) 9. Electrical cabinet fan with filter 10. Door locks 11. Air filter 12. Main switch 13. Connection socket Tach generator 14. XS 2 Interface 2002 Nordson Corporation
21 Description 2-11 Pulling the Electrical Cabinet Forward The electrical cabinet can be pulled forward for installation, maintenance and repairs. It must first be unlocked with the enclosed key. WARNING: Ensure that cables do not touch rotating or hot parts when the electrical cabinet is pushed back into place. Do not pinch cables. Fig. 2-5 MCSY357S070A0497 Main Switch (12, Fig. 2-4) Serves to switch the unit On/Off. Position 0/OFF = unit is switched off. Position I/ON = unit is switched on. The main switch can be secured with padlocks against unauthorized switching. CAUTION: When the main switch is set to 0/OFF, the inert gas equipment is turned off and the tank is deaerated. This could cause hardening of the adhesive in the tank (Refer also to Daily Shutdown). NOTE: When using a programmable week timer (option), the main switch must always be in position I/ON. Turning Unit On 1. Ensure that the contacts Release unit of the interface XS 2 are switched externally or as bridge circuits (Refer to Installation). 2. Set main switch to the position I/ON. 3. Press button Heating on Nordson Corporation
22 2-12 Description Control System (2, Fig. 2-4) For operation see manual Control System. Channel Assignment for MC xx without Heated Can Receptacle Channel 1 Tank (melt zone) Channel 2 Heated hose 1 Channel 3 Application head 1 Channel 4 Channel 5 Heated hose 2 Application head 2 Only with MC 12-1x2 MC 12-2x1 MC 24-1x2 MC 24-2x1 MC 24-2x2 Channel 6 Heated hose 3 Only with MC 24-2x2 Channel 7 Application head 3 Channel 8 Heated hose 4 Channel 9 Application head 4 Channel Assignment for MC 12 with Heated Can Receptacle Channel 1 Channel 2 Heated can receptacle Tank (melt zone) Channel 3 Heated hose 1 Channel 4 Application head 1 Channel 5 Heated hose 2 Only with MC 12-1x2 MC 12-2x1 Channel 6 Application head 2 Indicator Light (1, Fig. 2-4) Indicates except for the yellow light the same operating modes as the indication lamps of the control system (see also section Troubleshooting and manual Control System). White Green Yellow (only with option Level control) Red Unit turned on Unit ready for operation Lowest tank level Collective fault indication Button Heating On/Off (3 and 4, Fig. 2-4) The buttons switch the heating (load current circuit) on or off. (Also refer to Main Switch and Week Timer) Nordson Corporation
23 Description 2-13 Button Purge (6, Fig. 2-4) Pressing the button activates an additional Inert gas flush, e.g. after the tank has been filled. Lighted Symbol Inert Gas Bottle Empty (7, Fig. 2-4) Lights when the inert gas bottle is empty. The red indication lamp and the red lamp of the control system also light up. The error number 66 is also displayed. Lighted Symbol Inert Gas Supply (5, Fig. 2-4) Lights up when inert gas injection is forcibly actuated after the tank hood is closed (parameter C1) and when inert gas is injected by the inert gas control (parameter Con and CoF). Blinks when the button Purge is pressed. Programmable Week Timer (Option) (8, Fig. 2-4) Refer to manual Week Timer for operation. The week timer turns the load current circuit (heaters) on/off. The switching function of the week timer and of the buttons Heating on and Heating off are the same, meaning: A unit turned on with the week timer can be turned off with the button Heating off A unit turned on with the button Heating on can be turned off by the week timer. NOTE: When a week timer (option) is used, the main switch must always be in the position I/ON. Electrical Cabinet Aeration (9 and 11, Fig. 2-4) Serves to aerate the electrical cabinet, which reduces the inside temperature. The filter must be cleaned or replaced regularly (Refer to Section 5, Maintenance). Tach Generator Connection Socket (13, Fig. 2-4) Serves to connect a tach generator (Accessories). The tach generator is available from Nordson. If part of the shipment, refer also to operating manual Tach Generator. WARNING: When connecting to Nordson units of the Meltex product line, the pilot voltage may not exceed 160 V DC. Failure to observe can result in damage to electronic components. NOTE: The pilot voltage must be aligned (see manual Control System) Nordson Corporation
24 2-14 Description XS 2 Interface (14, Fig. 2-4) Serves as a connection between the unit and customer s external devices. For connection allocation see Sections Installation and Wiring Diagram. Door Locks (10, Fig. 2-4) The electrical cabinet can be opened with the aid of the included key. Store the key such that it is accessible only to qualified and authorized personnel. WARNING: Allow only qualified and authorized personnel to open the electrical cabinet. WARNING: Disconnect equipment from the line voltage. 10. Protective Panels WARNING: Do not operate the unit without protective panels. For installation, maintenance, etc. the side panels can be removed and the rear panel tilted outward. The panel fasteners can be unlocked with the square spanner supplied with the unit. CAUTION: Observe cable length limits between electrical cabinet and switch amplifier of the level control (option) when the protective cartridge holding the switch amplifier is removed. Fig. 2-6 MCSY354S050A0497X 2002 Nordson Corporation
25 Description ID Plate The ID plate contains the following information: Code Nordson Engineering GmbH D Lüneburg Germany R P/N Ser. U I A f V 50/60 Hz P W Pmax W XXSY015L034A0395 Fig. 2-7 Information Description Unit Code Unit description and configuration code P/N Article number Ser. Serial number U Operating voltage Volt I Fuse rating Ampere f Frequency of line voltage Hertz P Power consumption of the unit Watt P max Maximum power consumption of the unit and connected accessories Watt 2002 Nordson Corporation
26 2-16 Description 2002 Nordson Corporation
27 Section 3 Installation 2002 Nordson Corporation
28 3-0 Installation 2002 Nordson Corporation
29 Installation 3-1 Section 3 Installation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. 1. Transport See Section Overview for weight. Only use suitable methods of transport. Mount the unit to a special pallet (with rubber vibration absorbers) using angle brackets (Fig. 3-1). Pack with sturdy materials; fill the spaces between the unit and packing with suitable filling material. Protect the unit from humidity, excessive dust, impacts and vibrations. MCSY358S065A0497 Fig. 3-1 Lifting (Unpacked Unit) See section Specifications for weight. Lift at the unit frame using suitable lifting equipment or a forklift. 2. Unpacking Unpack the unit carefully and check for damage caused during transport. Save the special pallet and angle brackets for later use. Recycle packing materials or dispose of properly according to local regulations. 3. Removing Operate the unit until empty, separate all connections from the unit and allow the unit to cool down. 4. Storage Do not store the unit in the open! Protect the unit from humidity, excessive dust and great fluctuations in temperature (forming of condensation). 5. Disposal Ensure proper disposal of the unit according to local regulations Nordson Corporation
30 3-2 Installation 6. Setting Up Set up the unit only in surroundings which correspond to its Degree of Protection (see section Overview). Do not set up in explosive surroundings! Protect the unit against vibrations. Remove transport protections (if present). Check all plug and screw connections for tightness. Leave enough free space around the unit (Fig. 3-2). MCSY355S070A0497 Fig Overview NOTE: The overview does not replace the following description. Mount indicator light Exhaust hot melt material vapors if necessary (can only escape when the tank lid is open) Electrical connections Connect inert gas Install heated hose MCSY352L110B0697 Fig Nordson Corporation
31 Installation Mounting Indicator Light The indicator lamp must be mounted to the electrical cabinet (it was removed for transport). 9. Exhausting Hot Melt Material Vapors Make sure that hot melt material vapors do not exceed the prescribed limits. Exhaust the vapors if necessary. Provide sufficient ventilation in the area where the machine is set up. 10. Electrical Connections WARNING: Risk of electrical shock. Failure to observe can result in personal injury, death or equipment damage. Laying Cables Make sure that cables do not come into contact with any rotating and/or heated unit components. Do not pinch cables and check regularly for damage. Replace damaged cables immediately! Line Voltage WARNING: The unit may only be operated with the line voltage indicated on the ID plate. NOTE: Permissible tolerances regarding the rated line voltage are +5% / 10%. NOTE: The mains connection cable must have a cross section matching the rated power consumption. See ID plate for rated current. The mains terminals are located in the electrical cabinet. See Wiring Diagram for connection allocation. Tach Generator (Accessories) The tach generator is connected at the connection socket (13, Fig. 2-4). See Wiring Diagram for connection allocation. The tach generator is available from Nordson. If it is a part of the shipment, refer also to the manual Tach Generator. WARNING: When connecting Nordson units of the Meltex product line, the pilot voltage may not exceed 160 V DC. Failure to observe can result in damage to electronic components. NOTE: The pilot voltage produced by the tach generator must be aligned (see Control System) Nordson Corporation
32 3-4 Installation XS 2 Interface Serves as a connection between the unit and the customer s external devices. In special versions of the unit, the connection allocation may differ from the one described here. Refer to the Wiring Diagram for the actual connection allocation of such units. NOTE: Use only shielded cables/lines. Connect the shielding to ground according to EMC requirements. NOTE: Inductive loads (e.g. solenoid valves) connected to the unit must be equipped with a protective device (e.g. recovery diode) that deactivates the resulting induction voltage when an inductive load is turned off. Standard connection allocation XS 2 Interface (see also Wiring Diagram) Pin Function Notes Input Output Potential free 1 24 V DC 1 / 2, 5, 10, 11 factory bridged 2 Motor 1 on / off 1 / 2 factory bridged 3 Valve control 1 3 / 4 factory bridged 4 24 V DC 5 Motor 2 on / off 1 / 5 factory bridged 6 Valve control 2 6 / 7 factory bridged 7 24 V DC 8 Temperature setback External on/off 9 Not allocated 10 Release Unit (Main contactor activated) 1 / 10 factory bridged 11 Release All motors 1 / 11 factory bridged 12 External supply voltage for outputs pins 13, 14 and Message Ready for operation Supplied by external voltage at pin Message Collective fault Supplied by external voltage at pin External supply voltage for output pin Release Control unit (ES...) Supplied by external voltage at pin Not allocated 18 Valve control 3 18 / 19 factory bridged V DC 20 Not allocated 21 Valve control 4 21 / 22 factory bridged V DC 23 Not allocated 24 Not allocated 25 External supply voltage for output pin Level control (option) indication Full Supplied by external voltage (Not assigned for option Can receptacle) at pin External supply voltage for output pin Level control (option) indication Fill Supplied by external voltage at pin Not allocated 30 Not allocated 31 Not allocated 32 Indication Inert gas empty Supplied by external voltage at pin Nordson Corporation
33 Installation Installing Heated Hoses WARNING: Hot! Risk of burns. Wear heat protective gloves. Connecting If cold hot melt material can be found in the hose connection fitting (1) and/or hose connection (2), these components must be heated until the material softens (approx. 80 C, 176 F). 1. First connect the hose (3) electrically to the unit. For more than one hose: every hose connection fitting is allocated to a corresponding connection socket. Do not mistakenly exchange! NOTE: For units with recirculation hoses: do not mistake recirculation hoses for feed hoses. 2. Heat the unit and hose to approx. 80 C (176 F). Fig. 3-4 Principle drawing MXHH001S050A Screw the hose onto the unit. NOTE: Close unused hose connection fittings with Nordson screw caps. Disconnecting WARNING: System and hot melt material pressurized. Relieve pressure before disconnecting heated hoses. Failure to observe can result in serious burns. Relieving Pressure 1. Set motor speed to 0 RPM; switch off motor(s). 2. Place a reservoir under the nozzle(s) of the application head/hot melt handgun. 3. Activate the solenoid valve(s) electrically or manually; or, pull the trigger of the hot melt handgun. Repeat this procedure until no more hot melt material flows out. 4. Re use the hot melt material or dispose of properly according to local regulations. Second Open jawed Wrench Using a second open jawed wrench prevents the hose connection fitting on the unit from turning. MXHH002S033A0295 Fig. 3-5 Principle drawing 2002 Nordson Corporation
34 3-6 Installation 12. Pneumatic Safety Valve (Option) See manual Safety Valve. 13. Inert Gas Equipment See manual Inert Gas Equipment Nordson Corporation
35 Section 4 Operation 2002 Nordson Corporation
36 4-0 Operation 2002 Nordson Corporation
37 Operation 4-1 Section 4 Operation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. 1. Filling the Tank WARNING: Hot! Risk of burns. Wera safety goggles and heat-protective gloves. Risk of burns from the tank lid when the tank hood has been opened. Hot adhesive can splash out of the tank when it is being filled. Insert the adhesive carefully. Before filling the tank, make sure the tank and hot melt material are clean and free of foreign substances. Foreign substances can damage the unit and accessories. Also ensure that the inert gas inlet hole and the tank deaeration hole are not plugged with adhesive. NOTE: Do not completely empty the tank. If there is too little adhesive in the tank, the adhesive can overheat. This can cause adhesive residue and hardening, resulting in malfunctioning. Maximum Filling Level Ensure that the melted adhesive can not reach the inert gas inlet hole and the tank deaeration hole. Tank with Optional Can Receptacle Carefully insert the open can with the opening down. If necessary, use a thorn to punch a hole in the bottom of the can. This avoids formation of a vacuum in the can; a vacuum could prevent the adhesive from flowing out. MCTK030S050A01998 Fig Nordson Corporation
38 4-2 Operation Opening and Closing Tank WARNING: Hot! Risk of burns on the tank lid after opening the tank hood. Wear heat protective gloves. WARNING: Do not operate the unit when the tank lid is open. Hot melt material vapors which may contain hazardous substances can escape. 1 WARNING: The tank lid may not be opened until the quick dearation procedure is audibly completed CAUTION: Do not operate unit when tank hood is open. When the hood is open the tank is relieved of inert gas pressure, and no inert gas pressurization occurs. This can result in the adhesive hardening in the tank. Opening tank 1. Open the tank hood (1) (Also refer to Tank Hood Switch). 2. Open the tank lid lock (3) Pull the tank lid open with the aid of the tank lid handle (2) until the tank lid detent (5) locks into place. Closing tank 1. Hold on to the tank lid with the aid of the tank lid handle (2). Pull the tank lid detent (5) back and close the tank lid. 2. Lock the tank lid lock (3). 3. Close the tank hood (1) (Also refer to the Tank Hood Switch). Tank Hood Switch The tank hood switch (4) activates the following functions on opening and closing the tank hood (1): 5 Tank hood is opened Tank is relieved of inert gas pressure (quick deaeration). Tank hood is closed The tank is pressurized with inert gas for the length of time set on the control system (parameter C1) After the time set in parameter C1 has expired, the tank is pressurized with inert gas at regular intervals as set on the control system (parameters Con and CoF). 6 MCSY335S220B0697 Fig Nordson Corporation
39 Operation Setting Temperatures The setting of temperatures as well as all other functions of the control system are described in detail in manual Control System. NOTE: Processing temperature is also referred to in the description of the Control System as nominal value temperature. NOTE: The temperature setting is determined by the processing temperature prescribed by the hot melt material supplier. Do not exceed the maximum operating temperature of the unit or heated system components. Nordson assumes no guarantee and/or liability for damage caused by incorrect temperature settings. NOTE: Depending on the adhesive used, the overtemperature thermostats of the tank and possibly of the optional can receptacle may need to be adapted to the maximum processing temperature of the adhesive (This may mean that the overtemperature thermostats have need to be replaced). The switchoff value of the thermostat may not exceed the max. operating temperature of the unit! For thermostats see section Specifications. General Values Heating zone / Temperature / Time The values in the table are general values for temperature settings. Setting Heated can receptacle (Option) 20 C (68 F) below prescribed processing temperature Tank 10 C (50 F) below prescribed processing temperature Undertemperature value 10 C (50 F) below set processing temperature Overtemperature value 10 to 30 C (50 86 F) above set processing temperature Setback temperature Setback period As required As required Application head (Accessories) Prescribed processing temperature(s) Heated hose (Accessories) Prescribed processing temperature 2002 Nordson Corporation
40 4-4 Operation 3. Setting Hot Melt Material Feed Quantity Setting the hot melt material feed quantity, as well as all other functions of the control system, are described in detail in the manual Control System. Motor/Pump Speeds The motor/pump speed described here is the speed measured on the output shaft. The actual motor speed is much higher. NOTE: Avoid a permanent motor/pump speed of less than 5 RPM and more than 80 RPM to prevent excessive wear. Manual Operation The motor/pump speed corresponds to a set value and does not change. It can also not be controlled synchronous to a parent machine. Automatic Operation The motor/pump speed is controlled synchronous to parent machine speed. Parameters can be set. NOTE: Automatic operation is only possible if pilot voltage is present. NOTE: The pilot voltage must be aligned (see manual Control System) Nordson Corporation
41 Operation Initial Startup After the unit has been properly installed, initial startup can take place. NOTE: The unit was subjected to extensive functional tests prior to shipment. In doing so, the tank was filled with a special test material. Residues of this material may still be present in the unit. To remove these residues, melt and feed several kilograms of hot melt material before starting production. NOTE: The temperature setting is determined by the processing temperature prescribed by the hot melt material supplier. Do not exceed the maximum operating temperature of the unit or heated system components. Nordson assumes no guarantee and/or liability for damage caused by incorrect temperature settings. NOTE: Nordson gear pumps may not be operated without hot melt material. Before switching on the motor, make sure the tank is filled. NOTE: Avoid a permanent motor/pump speed of less than 5 RPM and more than 80 RPM to prevent excessive wear. NOTE: The operator must make himself familiar with the manual Control System before carrying out the following steps. 1. Ensure that the contacts Release unit of the interface XS 2 are switched externally or as bridge circuits (See Installation). 2. Ensure that the tank is pressurized with inert gas. 3. Set main switch to position I/ON. 4. If part of this unit (option) set week timer (see operating manual Programmable week timer). 5. Activate button Heating on. 6. If available, calibrate the optional level control (refer to manual Switch Amplifier CSV with Level Sensor). 7. Fill the tank. 8. Close tank lid and tank hood. 9. Carry out all settings on the Control System. 10. Wait until the unit is ready for operation (green lamp is lit). 11. Pre select the motor. 12. Switch on the motor. 13. Set motor/pump speed according to the desired material amount Nordson Corporation
42 4-6 Operation 5. Daily Switch ON/OFF Daily Switch ON/OFF has the same meaning as the terms starting and stopping. Daily Switch ON NOTE: Nordson gear pumps may not be operated without hot melt material. Before switching on the motor, make sure the tank is filled. NOTE: Avoid a permanent motor/pump speed of less than 5 RPM and more than 80 RPM to prevent excessive wear. 1. Ensure that the tank is pressurized with inert gas. 2. Set main switch to position I/ON. 3. Activate button Heating on. 4. Fill hot melt material if necessary. 5. Wait unil the unit is ready for operation (green lamp is on). 6. Pre select motor(s). 7. Switch on the motor. Daily Switch OFF (Inert Gas also Off) 1. Switch off the motor. 2. Set main switch to position 0/OFF. 3. Secure main switch with padlocks if necessary to prevent unauthorized operation. CAUTION: When the main switch is set to 0/Off, the inert gas equipment is turned off and the tank is deaerated. This could cause hardening of the adhesive in the tank. Daily Switch OFF (Inert Gas not Off) 1. Switch off the motor. 2. Activate button Heating Off. 6. Emergency Switch OFF WARNING: Switch off the unit immediately in any emergency situation. 1. Set main switch to 0/OFF. 2. After standstill and before switching the unit on again, have the malfunction eliminated by qualified personnel Nordson Corporation
43 Operation Settings Record Form Make a copy of the form before filling it out. Production information: Hot melt material: Supplier Processing temperature Viscosity Cleaning agent: Supplier Flash point Leading channel: Tank (factory-set) Processing temperatures (nominal value temperatures): Heated can receptacle (Option) Tank Heated hose (Accessories) 1) 2) 3) 4) Application head (Accessories) 1) 2) 3) 4) Air heater (Accessories) 1) 2) 3) 4) Motor /pump speed: Motor/Pump 1) 2) Air pressure at application head (Accessories): Control air 1) 2) 3) 4) Spray air 1) 2) 3) 4) Notes: Name Date 2002 Nordson Corporation
44 4-8 Operation 2002 Nordson Corporation
45 Section 5 Maintenance 2002 Nordson Corporation
46 5-0 Maintenance 2002 Nordson Corporation
47 Maintenance 5-1 Section 5 Maintenance WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. NOTE: Maintenance is an important preventative measure for maintaining operational safety and extending the lifetime of the unit. It should not be neglected under any circumstances. 1. Relieving Pressure WARNING: System and hot melt material under pressure. Before removing heated hoses, application heads or hot melt handguns, relieve system pressure. Failure to observe can result in serious burns. WARNING: Hot! Risk of burns. Wear heat-protective gloves. 1. Set motor speed to 0 RPM; switch off motor(s). 2. Place a reservoir under the nozzle(s) of the application head/hot melt handgun. 3. Trigger the solenoid valve(s) electrically or manually; or, pull the trigger of the hot melt handgun. Repeat this procedure until no more hot melt material flows out. 4. Re use hot melt material or dispose of properly according to local regulations Nordson Corporation
48 5-2 Maintenance 2. Daily Maintenance The stated intervals are general guidelines based on experience. Depending on the location of the unit, production conditions and operating time of the unit, other maintenance intervals may prove necessary. Unit part Activity Interval Refer to Entire unit External cleaning Daily Page 5-3 Tank Inspection for external damage Daily Page 5-3 Visual inspection for impurities in Before every tank filling the tank Visual inspection of holes for inert gas supply, air exhaust, etc. to check whether they are clogged with adhesive; clean if necessary 3. Regular Maintenance The stated intervals are general guidelines based on experience. Depending on the location of the unit, production conditions and operating time of the unit, other maintenance intervals may prove necessary. Unit part Activity Interval Refer to Electrical cabinet fan Check filter, clean or replace if Depending on dust Page 5-3 necessary accumulation; daily if necessary Power cable Inspection for damage Every time the unit is serviced Air hoses Inspection for damage Every time the unit is serviced Gear pump Refer to separate manual Motor / gear box Refer to separate manual Tank Refer to separate manual Safety valve Refer to separate manual Inert gas equipment Refer to separate manual Air dryer with compressed air filter (Special equipment) Refer to separate manual 2002 Nordson Corporation
Hot Melt Material Applicator MC 6
Hot Melt Material Applicator Manual P/N 403 022 D English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice
More informationHot Melt Applicator MC 405 for Foil Bags
Hot Melt Applicator for Foil Bags Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY NOTE This manual is for products with the following P/N: 8015767 8022490 8027924 8037680 8018042 8023117 8031127
More informationElectropneumatic Hot Melt Application Heads EP 34 / EP 34 S / EP 34 SD
Electropneumatic Hot Melt Application Heads Manual P/N 409 090 A English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson
More informationDrum Melters DG 21 / DG 201
Drum Melters DG 21 / DG 201 Manual P/N 464 839 A - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products
More informationBulk Melters BM 200 with Gear/Gerotor Pump for 200 l Drums
Bulk Melters BM 200 with Gear/Gerotor Pump for 200 l Drums Manual P/N 464 958 C - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order
More informationBulk Melters BM 200 with Piston Pump for 200 l Drums
Bulk Melters BM 200 with Piston Pump for 200 l Drums Manual P/N 464 937 B - English - NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number
More informationHot Melt Application Head Series PW...
Hot Melt Application Head Series... Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This
More informationHot Melt Material Applicator MC 4420
Hot Melt Material Applicator Manual English NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This is
More informationSponge Cleaner. Manual P/N A English. Issued 05/03 NORDSON (UK) LTD STOCKPORT
Sponge Cleaner Manual P/N 768 651 A English Issued 05/03 NORDSON (UK) LTD STOCKPORT Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected
More informationFill Sentry. Automated Fill System. Customer Product Manual Part A. NORDSON CORPORATION
Fill Sentry Automated Fill System Customer Product Manual Part NORDSON CORPORATION www.nordson.com CAUTION: If this equipment is used with other Nordson equipment, refer to the manuals provided with that
More informationU7698E Flame Detector
U7698E Flame Detector Customer Product Manual Issued 3/02 NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General
More informationEnvirocoat Twin Cyclone Powder Coating Booth
Envirocoat Twin Cyclone Powder Coating Booth Manual P/N 779166 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue
More informationSeal Sentry Series 10 Bead Detection System
Seal Sentry Series 10 Bead Detection System Customer Product Manual P/N 321 289D02 This equipment is regulated by the European Union under WEEE Directive 2002/96/EC). See www.nordson.com for information
More informationBulk Melters BM 200 with Piston Pump - EASY Pneumatics -
Bulk Melters BM 200 with Piston Pump - EASY Pneumatics - Manual - English - Issued 05/06 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note After approx. December 2003, this manual applies to the entire series.
More informationPowder Conditioning System
Powder Conditioning System Manual P/N 779168 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Table I Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue Box, CF,
More informationLevel Monitor LA 100
Level Monitor LA 100 Manual English NORDSON BENELUX MAASTRICHT THE NETHERLANDS www.nordson.com Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which
More informationFluidking. Manual P/N A English NORDSON (UK) LIMITED STOCKPORT UK
Manual P/N 768 643 A English NORDSON (UK) LIMITED STOCKPORT UK Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected by copyright. Original
More informationFixed Reclaim System
Fixed Reclaim System Manual P/N 779163 --English-- Keep for Future Reference Nordson China Sourcing - Shanghai Trademarks AccuJet, Aquaguard, Asymtek, Automotive, Autotech, Blue Box, CF, Can Works, Century,
More informationHot-melt adhesive extruder EEX40
Hot-melt adhesive extruder EEX40 Manual 110900563/001 - English - Nordson Deutschland GmbH Buchholz-Mendt GERMANY Note This manual applies to the entire series. Part number P/N = 7549584 Notice This is
More informationDuraDrum Bulk Melters DD200
DuraDrum Bulk Melters Manual English Issued 11/07 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This manual applies to the entire series. Order number P/N = Order number for Nordson products Notice This
More informationHot Melt Material Applicator MC 7
Hot Melt Material Applicator MC 7 Parts List P/N 735003A English Issued 2/06 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation
More informationLA 820 / LA 820 RC Liquid Adhesive Gun
Liquid Adhesive Gun Manual English NORDSON BENELUX MAASTRICHT THE NETHERLANDS Order number P/N = Order number for Nordson products Notice This is a Nordson Corporation publication which is protected by
More informationHot Melt Applicators SB60 BoD
Hot Melt Applicators Manual - English - Edition 06/14 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This document applies to the entire series. Order number P/N = Order number for Nordson articles Note
More informationLiquid Adhesive Detection System Alarm Box
Liquid Adhesive Detection System Alarm Box Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.
More informationSeries AD-31 and Series L4 Extrusion Handguns
Series AD-31 and Series L4 Extrusion Handguns Customer Product Manual Issued 5/05 NORDSON CORPORATION DULUTH, GEORGIA USA www.nordson.com For CE Declaration, refer to melter documentation. Nordson Corporation
More informationGD-500 Bead Detection System
GD-500 Bead Detection System Customer Product Manual Issued 4/08 NORDSON CORPORATION DULUTH, GEORGIA USA www.nordson.com Nordson Corporation welcomes requests for information, comments, and inquiries about
More informationAutomatic Hot Melt Melter/Feeder Retrofit Kit Mechanical Float Model. Part104506A
Automatic Hot Melt Melter/Feeder Retrofit Kit Mechanical Float Model Part456A NORDSON CORPORATION. AMHERST, OHIO USA Corporation welcomes requests for information, comments and inquiries about its products.
More informationFillEasy C Adhesive Feed System
FillEasy C Adhesive Feed System Customer Product Manual Issued 5/10 This document contains important safety information Be sure to read and follow all safety information in this document and any other
More informationAltaSpray Plus Applicators
AltaSpray Plus Applicators Customer Product Manual Issued 5/3 This document contains important safety information Be sure to read and follow all safety information in this document and any other related
More informationBulk Melters AltaPail
Bulk Melters AltaPail Manual - English - Edition 02/12 NORDSON ENGINEERING GMBH LÜNEBURG GERMANY Note This document is for products with the following P/N: 7165698 7157455 7157502 7157503 Order number
More informationOK, OKA, OKAF; ELD; ELDM; ELH; OKC; SC; SCA; SCAF; OK-LN; OKA-LN; OKAF-LN.
INSTALLATION, OPERATION & SERVICE MANUAL FOR COOLER TYPES OK, OKA, OKAF; ELD; ELDM; ELH; OKC; SC; SCA; SCAF; OK-LN; OKA-LN; OKAF-LN. 1. Introduction This manual is a guide for the installation, maintenance
More informationHot-melt adhesive extruder EEX100
Hot-melt adhesive extruder EEX100 Manual 111121287/001 -- English -- NordsonDeutschlandGmbHBuchholz--MendtGERMANY Note This manual applies to the entire series. Part number P/N = 7552471 Notice This is
More informationCleanSpray System Operation
Nordson Corporation OPERATOR S CARD P/N 108684C CleanSpray System Operation Introduction The individual manuals for the CleanSpray Gun, CleanSpray Controller and Model 25B Pump are included with each component.
More informationNon-RTD Hot Melt Hose Replacement
Instruction Sheet P/N 7C 0 Safety WARNING: System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection or seal. Failure to relieve the system hydraulic pressure can result
More informationReplacing a Gun Thermostat
Instruction Sheet Replacing a Gun Thermostat WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.
More informationFC-2200 Flame Detector
FC-2200 Flame Detector Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all correspondence
More informationOriginal operating instructions Safety switch with guard locking AC901S AC902S
Original operating instructions Safety switch with guard locking AC901S AC902S 7390914/03 01/2017 Contents 1 Preliminary note...4 1.1 Explanation of symbols...4 2 Safety instructions...4 3 Items supplied...5
More informationTTV 1500 / TTV 3000 OPERATING MANUAL CONVEYING FAN TRT-BA-TTV TC EN
TTV 1500 / TTV 3000 EN OPERATING MANUAL CONVEYING FAN TRT-BA-TTV1500-3000-TC2016-26-004-EN Table of contents Notes regarding the operating manual... 2 You can download the current version of the operating
More informationInstruction Manual. Automatic fuel oil de-aerator SMART-FLO 3/K B100 COMPATIBLE
Sid Harvey s 605 Locust Street Garden City, NY 11530 Instruction Manual Automatic fuel oil de-aerator SMART-FLO 3/K Read manual before use! Observe all safety information! Keep manual for future use! 05.2015
More informationDC200 Digital Dispenser Operating Manual
DC200 Digital Dispenser Operating Manual 2015 Fisnar Phone: (973) 646-5044 E-mail: info@fisnar.com Table of Contents Product Safety Statements 4 Specifications 6 Accessories 6 External Controls 7 Machine
More informationUSER MANUAL. Version: 1.0. ROBE Show Lighting s.r.o. Czech Republic
USER MANUAL Version: 1.0 ROBE Show Lighting s.r.o. Czech Republic www.robe.cz Table of contents 1.Introduction 4 2.Cautions 4 3. Unpacking & Inspection 5 4. Setup 5 5. Operation 5 5.1.Control Module Operation
More informationInstallation and Operating Instructions DÜRR Regeneration Unit for X-ray developers XR 24, XR24 II, XR 24 Nova, XR 24 Pro
Installation and Operating Instructions DÜRR Regeneration Unit for X-ray developers XR 24, XR24 II, XR 24 Nova, XR 24 Pro 2006/01 Content Important Information 1. Notes... 3 1.1 CE - Labeling... 3 1.2
More informationOperational Instructions. Glue Applicator MS Translation from German to English
Operational Instructions Glue Applicator MS 200 Translation from German to English Table of Contents Product Description 1 General Safety Instructions 2 Safety Measures to be taken during Operation 3 Start-up
More informationInstruction Manual. Alarm Unit For Low Gas Level # Read manual before use! Observe all safety information! Keep manual for future use!
Mess-, Regel- und Überwachungsgeräte für Haustechnik, Industrie und Umweltschutz Lindenstraße 20 74363 Güglingen Telefon +49 7135-102-0 Service +49 7135-102-211 Telefax +49 7135-102-147 info@afriso.de
More informationTIH 300 S / TIH 400 S / TIH 500 S / TIH 700 S / TIH 900 S / TIH 1100 S
TIH 300 S / TIH 400 S / TIH 500 S / TIH 700 S / TIH 900 S / TIH 1100 S EN OPERATING MANUAL INFRARED HEATING PANEL TRT-BA-TIH300S-TIH400S-TIH500S-TIH700S-TIH900S-TIH1100S-TC-002-EN Table of contents Notes
More informationOperating manual. a Look Solutions 1 product
Operating manual a Look Solutions 1 product Set of Equipment supplied 1 Unique 2 1 tank lid with quick connector, silicon tube and air valve filter 1 canister of UNIQUE-fluid, 2l 1 manual As an option:
More informationOperating instructions Page 12
Operating instructions Page 12 Refrigerator with explosion-proof interior container Read the operating instructions before switching on for the first time 7082 271-00 LKEXv 910 Disposal notes The appliance
More informationAirUnit. Operating manual. mfh systems modern floor heating. Decentralised domestic ventilation
mfh systems modern floor heating AirUnit Decentralised domestic ventilation Operating manual List of contents, Operating manual Page 1. General information... 02 2. Device description... 03 3. Adjustment
More informationInstruction Manual Suppository Penetration Tester. Type PM 30
Instruction Manual Suppository Penetration Tester Type PM 30 ERWEKA GmbH * Ottostr. 20 22 * 63150 Heusenstamm * Germany * Tel: +49 (0) 6104 6903-0 Fax: +49 (0) 6104 6903-40 * E-mail: info@erweka.com *
More informationResidential Gas Condensing Boiler Greenstar ZBR16/21/28/35/42-3A... ZWB28/35/42-3A...
70 80 99-00-O Residential Gas Condensing Boiler ZBR//8/35/4-3A... ZWB8/35/4-3A... 70 80 993 (03/03) CA/US Operating Instructions Contents Contents Key to symbols and safety instructions............................
More informationBench-Top Vacuum Oven with 28 segments programmable controller
Bench-Top Vacuum Oven with 28 segments programmable controller DZF-6000F Series Vacuum Oven MTI Corporation www.mtixtl.com 1 Safety notes DZF Vacuum Oven Please read the following safety notes carefully
More informationOperating Instructions for Reka Hot-Melt Glue Applicators
Operating Instructions for Reka Hot-Melt Glue Applicators TR 700 TR 70 TR 80 TR 60 TR 50.4 TR 55 Table of Contents 1. Product Description 3 2. General Safety Instructions 4 3. Safety Measures to be taken
More informationULTRA LOW TEMPERATURE FREEZER. User Manual
ULTRA LOW TEMPERATURE FREEZER User Manual Note:Kaltis reserves the right to modify any parts of this manual without prior notice. 1. No part of this manual may be reproduced in any form, or translated
More informationInstructions manual DEHUMID HP50
Instructions manual DEHUMID HP50 Table of contents 1. Unpacking 3 2. Intended use 3 3. Disposal 3 4. Safety instructions 3 5. Functional principle 4 6. Automatic defrosting system 4 7. Set up and transportation
More informationInstallation and operating instructions. Temperature difference controller 6 inputs, 3 outputs, integrated data logger for SD card
SOLARTHERMIE - SOLAR THERMAL - SOLAR TÉRMICO - SOLAIRE THERMIQUE - SOLARE TERMICO Installation and operating instructions Temperature difference controller 6 inputs, 3 outputs, integrated data logger for
More informationAIRGOCLEAN 10 E OPERATING MANUAL AIR CLEANER TRT-BA-AIRGOCLEAN10E-TC-001-EN
AIRGOCLEAN 10 E EN OPERATING MANUAL AIR CLEANER TRT-BA-AIRGOCLEAN10E-TC-001-EN Table of contents Notes regarding the operating manual... 1 You can download the current version of the operating manual and
More informationRefrigerant Recovery Machine. Model No Operating Manual
Refrigerant Recovery Machine Model No. 25700 Operating Manual Safety Precautions WARNING : TO PREVENT PERSONAL INJURY AND / OR EQUIPMENT DAMAGE, CAUTION - Risk of injury. This equipment should only be
More informationProduct Manual Glue Applicators MS 80 and MS 200
Product Manual www.pakarte.com Glue Applicators MS 80 and MS 00 Translation from German to English Table of Contents Product Description General Safety Instructions Safety Measures to be taken during Operation
More informationKM300 Carbon Monoxide Detection System Installation Manual
GE Security KM300 Carbon Monoxide Detection System Installation Manual P/N 1068922 REV 2.0 16SEP09 Copyright Copyright 2009 GE Security, Inc. All rights reserved. This document may not be copied in whole
More informationHTD. High Temperature Non-Cycling Refrigerated Compressed Air Dryers. Operation & Maintenance Manual. MODELS HTD 21 thru HTD 100
HTD High Temperature Non-Cycling Refrigerated Compressed Air Dryers Operation & Maintenance Manual MODELS HTD 21 thru HTD 100 - TABLE OF CONTENTS - 1.0 GENERAL 2 1.1 How to use this manual 1.2 Symbols
More informationUV Flame Supervision System
7 783 UV Flame Supervision System DETACTOGYR LFE50 Series 02 ISO 9001 The LFE50 is a self-checking UV flame supervision system designed for use with continuously operating burners or for burners running
More informationPOLYMIX PX-IG 2000 Operating Instructions
POLYMIX PX-IG 2000 Operating Instructions Voltage D 100-120V, 50/60 Hz D 210-250V, 50/60 Hz Please check that the voltage is correct and corresponds with the nameplate on the back of the machine. Manual
More informationUser manual UV Flash Dry C1
HENSEL-VISIT GmbH & Co. KG 1 HENSEL-VISIT GmbH & Co. KG Robert-Bunsen-Str. 3 D-97076 Würzburg GERMANY Tel. +49 (0) 931 27881-0 Fax: +49 (0) 931 27881-50 Email: info@hensel.de Internet: http://www.hensel.de
More informationLaboport Chemically-resistant Laboratory Pumps and Systems
Operating Instructions Read and observe these Operating Instructions! Laboport Chemically-resistant Laboratory Pumps and Systems N 810 FT.18 N 820 FT.18 N 840 FT.18 N 840.1.2 FT.18 N 810.3 FT.18 N 820.3
More informationOperating instructions
The energy you need Operating instructions Betacom 3 24c -A (H-GB) 30c -A (H-GB) GB, IE Contents Contents 1 Safety... 3 1.1 Action-related warnings... 3 1.2 Intended use... 3 1.3 General safety information...
More informationFlopurge TS. Operation Manual
Flopurge TS Operation Manual Part Number 079-0204 Spectron Gas Control Systems United Kingdom Unit 4, Herald Court, University of Warwick Science Park, Coventry, CV4 7EZ +44 (0)24 7641 6234 sales@spectron-gcs.com
More information30 Misting/Oscillating Fan Model Number 01030
30 Misting/Oscillating Fan Model Number 01030 READ AND SAVE THESE INSTRUCTIONS CAUTION: Before using this product read this manual and follow all safety rules and operating instructions. Failure to comply
More informationSteam Trap BK 45 BK 45-U BK 45-LT BK 46
Steam Trap BK 45 BK 45-U BK 45-LT BK 46 Original Installation Instructions 810437-08 Contents Foreword... 3 Availability... 3 Formatting features in the document... 3 Safety... 3 Use for the intended purpose...
More informationEnergy management function at adsorption dryer PDAD
Application note Energy management function at adsorption dryer PDAD Application note for use of the energy management function at adsorption dryer PDAD. Explanation, use and layout of purge air regulation
More informationOperating instructions
Operating instructions for Winterhalter Gastronom dishwasher GS 502 and GS 515 Contents Page 1 Intended use... 1 2 Installation and commissioning... 1 3 Safety instructions... 2 4 Operating panel... 3
More informationResidential Gas Condensing Boiler Greenstar combi 100 p / 151 p ZWB28-3A... ZWB42-3A...
Residential Gas Condensing Boiler Greenstar combi 00 p / 5 p ZWB8-3A... ZWB4-3A... Operating Instructions 708733 (07/04) US/CA Contents Contents Explanation of symbols and safety instructions.......................
More informationOperation Manual for Drying Storage Cabinet with Drying Unit U-5002
Operation Manual for Drying Storage Cabinet with Drying Unit U-5002 (software version 4-09 and above) Aplicable to the following cabinets: MSD-601-52, MSD-1202-52, MSD-1222-52 HSD-241-52, HSD-351-52, HSD-472-52,
More informationPDA20DX Air Purifying Dehumdifier Manual
PDA20DX Air Purifying Dehumdifier Manual Index Important Safe Guards Ambient Environment For Operating Components Diagrams---Parts Names Operating Introduction---How to operate - Functions of Control Panel
More informationSilent V4 Nr
Silent V4 Nr. 2933 0000 DE FR IT ES 21-6669 12052014 / A Made in Germany Ideas for dental technology Silent V4 Nr. 2933 0000 GLISH 1. Introduction... 2 1.1 Symbols... 2 2. Safety... 3 2.1 Intended Use...
More informationMillo / Millo pro. Nr x000 / 1805-x000. Ideen für die Dentaltechnik A
Millo / Millo pro Nr. 1804-x000 / 1805-x000 0609 21-6543 A Ideen für die Dentaltechnik 1 2 3 4 5 6 7 8 9 10 11 12 Millo / Millo pro No. 1804-x000 / 1805-x000 ENGLISH Content Introduction... 15 Symbols...
More informationSILENT V4 TRANSLATION OF THE ORIGINAL INSTRUCTIONS FOR USE. Made in Germany
SILT V4 TRANSLATI OF THE ORIGINAL INSTRUCTIS FOR USE Made in Germany 21-6669 26092016 1. Introduction... 2 1.1 Symbols... 2 2. Safety... 3 2.1 Intended Use... 3 2.2 Improper Use... 3 2.3 Ambient Conditions
More informationGEMINI TM DYNACONTROL TM HOSES Automatic & Manual Versions FOR DYNAMELT & DYNAMINI TM ADHESIVE APPLICATION SYSTEMS
ITW Dynatec c. 2006 Page 1 Revised 4/20/07 Description GEMINI TM DYNACONTROL TM HOSES Automatic & Manual Versions FOR DYNAMELT & DYNAMINI TM ADHESIVE APPLICATION SYSTEMS Adhesive supply hoses are electrically-heated,
More informationHot -melt adhesive extruder EEX100 -F5B2X2TWXMQXS
Hot -melt adhesive extruder EEX100 -F5B2X2TWXMQX Manual 110717869/001 -- English -- Nordson Deutschland GmbH D Buchholz--Mendt D GERMANY Note This manual applies to the entire series. erial no. 110717869/001
More informationInstruction Manual. Electronic gas and smoke detector GRM
Mess-, Regel- und Überwachungsgeräte für Haustechnik, Industrie und Umweltschutz Lindenstraße 20 DE-74363 Güglingen Telefon +49(0)7135-102-0 Service +49(0)7135-102-211 Telefax +49(0)7135-102-147 E-Mail
More informationINSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS FOR 870 SERIES INDUSTRIAL CONTROL PANELS
INSTALLATION, OPERATING & MAINTENANCE INSTRUCTIONS FOR 870 SERIES INDUSTRIAL CONTROL PANELS GENERAL INDEECO Industrial Control Panels are designed to provide years of trouble free operation if properly
More informationM-Sens 2. Online moisture measurement for solids. Operating Instructions. SWR engineering Messtechnik GmbH PART OF THE ENVEA GROUP
EN M-Sens 2 Operating Instructions Online moisture measurement for solids SWR engineering Messtechnik GmbH PART OF THE ENVEA GROUP CONTENTS Page 1. System overview.............................................
More informationUser instructions DHP-AT
User instructions DHP-AT VUGFC202 If these instructions are not followed during installation and service, Danfoss A/S liability according to the applicable warranty is not binding. Danfoss A/S retains
More informationProduct Manual for Pneumatic Reka Glue Guns
Product Manual for Pneumatic Reka Glue Guns www.pakarte.com TR 60 LCD TR 70 LCD Translation from German to English TR 80 LCD TR 55 LCD TR 700 TR 50.4 TR 50.4 25 TR 55 LCD TR 60 LCD TR 700 TR 70 LCD TR
More informationOperating Instructions. PowerFill. Automatic Granulate Conveyor for perfectmelt SE
Operating Instructions PowerFill Automatic Granulate Conveyor for perfectmelt SE - 020100 - 2 Contents Introduction 4 Safety instructions 5 Safety measures with respect to the adhesive 5 Safety measures
More informationCAUTION. Installation Manual
System Controller SC-301-6M CAUTION Installation Manual In order to use this product safely, read this installation manual carefully and follow the installation instructions. Potential dangers from accidents
More informationSection 11. Electrical System. 42--CF200--MA--08 (formerly 42-65) Issued 5/96 P/N B. E 1996 Nordson Corporation All rights reserved
ection 11 Electrical ystem 11-0 Electrical ystem Table of Contents i Table of Contents ection 11 Electrical ystem 1. Introduction... 11-1 Electrical Operation... 11-1 Heating Zones... 11-2 2. Electrical
More informationPropane Flame Projector Safety instructions and operating manual
Bigflame Propane Flame Projector Safety instructions and operating manual 1 Flame projector Bigflame Safety instructions Caution The directions in this manual must be followed strictly. It is imperative
More informationOperating instructions
Operating instructions Capriz 2 24c 28c GB, IE Contents Contents 1 Safety... 3 1.1 Action-related warnings... 3 1.2 Intended use... 3 1.3 General safety information... 4 2 Notes on the documentation...
More informationInstruction Manual. Bucket Oil Pump
Instruction Manual Bucket Oil Pump 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2016 Gold Medal Products Co. Part No. 79064E SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent
More informationUSER'S INFORMATION MANUAL
USER'S INFORMATION MANUAL : If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Do not store or use gasoline
More informationCRU-S Series Stainless Steel Condensate Recovery Unit
IM-UK-CRU-S UK Issue 1 CRU-S Series Stainless Steel Condensate Recovery Unit 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Storage, shutdown and equipment protection
More informationOwner s Manual. Model AC375C Refrigerant Recovery, Recycle, and Recharge Unit
Owner s Manual Model AC375C Refrigerant Recovery, Recycle, and Recharge Unit Model AC375C Recover, Recycle, and Recharge Unit for R-12 or R-134a Refrigerant Voltage: 220 230; 50 60 Hz SAFETY DEFINITIONS:
More informationPRESSURE WASHER MODEL NO: JETSTAR 1750 OPERATION & MAINTENANCE INSTRUCTIONS. WARNING Read the instructions before using the machine PART NO:
WARNING Read the instructions before using the machine PRESSURE WASHER MODEL NO: JETSTAR 1750 PART NO: 7333230 OPERATION & MAINTENANCE INSTRUCTIONS LS0711 INTRODUCTION Thank you for purchasing this CLARKE
More informationOPERATING INSTRUCTIONS FOR THE TP18SX-HP
OPERATING INSTRUCTIONS FOR THE TP18SX-HP PLEASE READ THIS INSTRUCTION MANUAL PRIOR TO USING THE MACHINE Version 07/11 OVERVIEW The TP18SX-HP is a professional carpet extractor, with excellent performance.
More informationOperating instructions Page 14. Refrigerator Read the operating instructions before switching on for the first time
Operating instructions Page 14 Refrigerator Read the operating instructions before switching on for the first time 7085 039-00 LKv 5710 Content Disposal notes... 14 Description of the appliance... 14 Safety
More informationHD 525 S 06/03 A ! 5.960
HD 525 S 5 960 845 A2005225 06/03! Please read these operating instructions before starting and strictly observe the Safety Instructions for High Pressure Cleaners (5.951-949). WARNING DO NOT SPRAY ELECTRICAL
More informationAcross-the-Line SERIES MP300 Combined Manual and Automatic
Across-the-Line SERIES MP300 Combined Manual and Automatic Metron Fire Pump Controllers conform to the latest requirements of National Fire Protection Association s Standard for Centrifugal Fire Pumps
More informationTECHNOSKLO Ltd. Držkov
TECHNOSKLO Ltd. Držkov Distillation apparatus for producing of distilled water TYPE DP 4000 Operating manual TECHNOSKLO Ltd. 468 24 Držkov 135 Czech Republic tel.: 00420 483 346 403 fax: 00420 483 385
More informationPage 1 of 18. Part# /5/2013
Part# 1002655-06 8/5/2013 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS
More informationEcono-Coat RCM 8000 Powder Spray Booth Installation Guide
Installation Guide P/N 1028657A Econo-Coat RCM 8000 Powder Spray Booth Installation Guide WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this
More information