ENCLOSED PARTS WASHER WITH HEATING SYSTEM ---EPW160-H

Size: px

Start display at page:

Download "ENCLOSED PARTS WASHER WITH HEATING SYSTEM ---EPW160-H"

Bernice O’Neal’
5 years ago
Views:

1 Please read and save these instructions. Read through this owner s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property. Please retain instructions for future reference. ENCLOSED PARTS WASHER WITH HEATING SYSTEM ---EPW60-H EPW 60-H Description Parts washer in large enclosed cabinet with high protection from solvent, splash & odor. Pneumatic washing gun suitable for rapid cleaning. Auxiliary heating sytem supplying Max. 50 Celsius Degree solvent which highly increases cleaning efficiency. Flourescent lighting system for bright view. External air fan brings excellent ventilation. Washing pressure: 70-0 PSI Washing recirculate flux: 0.8 Liter/min. Working area: 9**7.8 inch. Solvent capacity: 8-4 L.

EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Air requirement: 70-0 PSI@5CFM. General Safety Information.. Keep the working bench horizontal deviation less than degree angle.. KEEP WORK AREA CLEAN.

2 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Air requirement: 70-0 General Safety Information.. Keep the working bench horizontal deviation less than degree angle.. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area. 4. USE THE RIGHT TOOL. Don t force parts washer or attachment to do a job for which it was not designed for 5. Equip with our authorized hose parts while using ORGANIC CLEANING SOLVENT. 6. USE PROTECTIVE GLOVES. Do not use broken gloves. 7. DISCONNECT PARTS WASHER before servicing and when changing accessories. 8. MAKE SURE HEATING SWITCH IS OFF before you start the machine. 9. DO NOT START HEATING when the volume of solvent is lower than 8 liters. 0. DO NOT OPERATE WHEN CABINET COVER IS OPEN.. DO NOT USE SOLVENT WHICH IGNITION TEMPERATURE IS LOWER THAN 0 DEGREE CELCIUS.. DO NOT SET OPERATING TEMPERATURE higher than 50 degree Celsius.

Controller Air Regulator Heating On/Off Switch Power

3 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Parts Washer Contents Air Pressure Gauge Digital Temperature Controller Air Regulator Heating On/Off Switch Power Supply On/Off Switch Cleaning Gun Switch Air On/Off Switch 3

4 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Solvent Hose Solvent Drainage Quick Plug Water Level Indicator Fixed Bolt Air Inlet 4

5 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Water Level Indicator: To observe whether or not more solvent is needed Power Supply On/Off Switch: Turn on the switch for LED light & Ventilated fan electric supply Heating On/Off Switch: Turn on the switch for solvent heating. Cleaning Gun Switch: Press cleaning gun switch to clean parts with water/solvent. Air On/Off Switch: Turn on the black switch for air drying. Solvent Drainage: Use water outlet to get dirty solvent out. Solvent Hose: Connect with cleaning gun and tank. Fixed Bolt: Fixes tank to the frame Air Inlet: To connect with air compressor using φ8 hose Air Regulator: Adjust appropriate air pressure based on the parts type you are washing. Digital Temperature Controller: Adjust the setting temperature. (Details in temperature control instruction). Air Pressure Gauge: Indicates air inlet pressure 5

EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Assembly Assembly Accessories:.. 4. 5.

Attach Leg Reinforcers () to support legs (3) using M0 Screws and Flat Washers.

6 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Assembly Assembly Accessories: Lay down cabinet and connect support legs (3) with cabinet using 4 M Screws and Flat Washers. Attach Leg Reinforcers () to support legs (3) using M0 Screws and Flat Washers. Attach 4 foot pads (4) to the bottom of support legs (3). Turn the machine over and adjust the height of foot pad Tighten all fasteners. 6

7 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Operation Notice.. 4. Adding Solvent: Open cabinet cover, add solvent through the web. Minimum 8L, maximum 4 liters. Observe the water level indicator. Compressed Air Connect: Connect the air compressor φ8 hose with the quick fitting at the bottom of the cabinet. Adjust appropriate air pressure based on the parts type you are washing. LED light & ventilated fan: Plug parts washer into an electric power supply, turn on Power Supply On/Off Switch for LED light & ventilated fan. Adjust the setting temperature. Solvent Temperature Setting: Set Digital Temperature Controller for solvent heating. (Details in temperature control instruction) Cleaning: Put parts into the machine and close the door, using cleaning gun to wash and air drying. Finishing: Make sure to turn off Heating On/Off Switch, also Power Supply On/Off Switch after finished. Maintenance NOTE: Disconnect power and air before the maintenance. Replace the solvent when needed. Cleaning: Clean the solvent filter screen (7) regularly in case of clogging. Solvent Changing: Use water outlet to get dirty solvent out from tank. Twist φ Water Suction Faucet and fixed bolt off to take out tank for cleaning. Wiring Diagram 7

8 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Troubleshooting Chart Symptom (s) Cleaning gun only works with air, no solvent usage Possible Causes(s). Cleaning switch is OFF. Inadequate solvent Absorption pipe is blocked Corrective Action(s). Turn it on. Add more solvent into the tank. Check and clean the absorption pipe. Light doesn t work but fan still works. Light is broken. Replace bulb Fan doesn t work but light still works. Fan is broken. Temperature controller display abnormal. Possible loose connection. Pull out waterproof plug and replace with new fan Double check the connection.. Inadequate solvent Heating On/Off Switch is OFF.. Heating tube is broken Temperature cannot reach to what you set If washer does not remain on and heating. Factory reset is required 8 Add more solvent Turn on the Heating On/Off Switch Replace with new heating tube. Make sure F8: is set to off then hold Set button until it beeps

9 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Explosive View 9

10 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H Parts Part No Description Front Panel Pin Hinge Axis Cleaning Tank Cabinet Holder Web Filter Screen LED Light Light Hoop Cabinet Cover Gloves Gloves Hoop Back Door Rod Fan Cover Front Door Rod Ventilated Fan Cleaning Gun Cabinet Back Protective Shield Side Support Side Protective Shield Leg Reinforces Support Leg Foot Pad 0 Qty. pair 4 4

c. Press OK, Done. How to set Heating & Freezing? Our parts washer is only available with heating function, so this step is normally no use. a. Long press Set, b.

11 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H THERMOSTAT INSTRUCTION. Press ON, turn on the digital meter indicating real-time temperature.. How to set heating temperature? a. Short press Set, the temperature number starts blinking. b. Press, Up / Increase Temperature & Down / Decrease Temperature. c. Press OK, Done. How to set Heating & Freezing? Our parts washer is only available with heating function, so this step is normally no use. a. Long press Set, b. Short press Set, c. Press F0 indicate, C or H indicate, choose C or H C means freezing. d. Press OK, Done. H means heating 4. Code Reference:

12 EPW 60-H ENCLOSED PARTS WASHER EPW 60-H a. Long press Set F0 indicate, b. Long press Set Again to F c. Press choose F0 -- F8 d. Press OK CODE F0 F F F3 F4 F5 F6 F7 F8 FUNCTION HEATING SET TEMPERATURE RETURN DIFFERENCE N/A N/A TEMPERATURE CALIBRATION DELAY STARTING OVERHEATING ALARM DATA LOCK DEFAULT SET RANGE H/C N/A N/A -0~ +0 0~0 Mins -55~0 ON/OFF ON/OFF

BOTTOM MOUNT REFRIGERATORS & FREEZERS Installation, Operation and Maintenance Instructions

BOTTOM MOUNT REFRIGERATORS & FREEZERS Installation, Operation and Maintenance Instructions INSPECTION When the equipment is received, all items should be carefully checked against the Bill of Lading to