The Arden Oscillating Floor Fan

Transcription

1 The Arden Oscillating Floor Fan Net Weight 6kg. (13.10lbs) Model No. FP8014**-220 OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS

2 Important Safety Instructions WARNING: To avoid fire, shock and serious personal injury, follow these instructions. 1. Read your owner s manual and safety information before installing your new fan. Review the accompanying assembly diagrams. 2. Before servicing or cleaning unit, unplug unit from power outlet. 3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always unplug the fan before servicing. 4. Do not insert anything into the fan blades while the fan is operating. 5. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 6. Children should be supervised to ensure that they do not play with the appliance. 7. Ensure that the fan is switched off from the supply mains before removing the guard. 8. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. Additional Safety Instructions 1. To avoid possible shock, do not operate fan without blades. 2. The fan must be connected to a grounded electrical supply as a precaution against possible electrical shock. 3. Follow the recommended instructions for the proper method of operating your fan. WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for use with this product. Using parts and/or accessories not designated for use with this product will void your warranty and could result in personal injury or property damage. WARNING: Do not insert foreign objects in between rotating fan blades. WARNING: For indoor use only. Table of Contents Unpacking Instructions Electrical and Structural Requirements How to Assemble Your Floor Fan Maintenance Parts List

3 This Manual is Designed to Make it as Easy as Possible for You To Install, Operate, and Maintain Your Fan Unpacking Instructions WARNING Do not install or use fan if any part is damaged or missing. This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Fanimation. Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. Check to see that you have received the following parts: Motor assembly Timber tripod legs Hardware Bag Motor Assembly Timber Tripod Legs Hardware bag NOTE: The illustration shown is not to scale. Actual configuration or finishes may vary. Electrical and Structural Requirements ELECTRICAL REQUIREMENTS This fan requires a grounded electrical supply line of 220 volts AC, 50 Hz, 10 amp circuit. 2.4m power cord included. NOT for Damp Location Use. WARNING To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done by a licensed electrician. WARNING To Avoid Fire Or Electrical Shock, Do NOT Use This Fan With Any Solid-State Speed Control Device And Do NOT Use By Open Window. 3

4 How to Assemble Your Floor Fan 1. Attach the timber tripod legs to the motor assembly using 3/16-24 x 22 mm screws. Use the supplied T-wrench to tighten the screws to ensure the legs are securely attached to the motor assembly. Ensure legs are positioned with the sticker side facing inwards towards the mounting brackets. Do not over-tighten the screws. (Figure 1) Motor Assembly T-Wrench Leg Figure 1 HARDWARE USED: 3/16-24 x 22 mm CAP HEAD WITH SPRING WASHER x Assemble the rubber caps on to the screws of each leg. (Figure 2) Rubber Cap Figure 2 3. You have now completed the assemby of your fan. Plug cord directly into the wall socket and turn on the power supply. (Figure 3) Figure 3 4. Select the desired airflow, located on back of motor assembly by rotating switch clockwise. (Figure 4) 0 = OFF 1 = HIGH 2 = MEDIUM 3 = LOW Rotating Switch Figure 4 4

5 Maintenance Periodic cleaning of your fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive and/or non-abrasive cleaning agents are not required and should be avoided to prevent damage to finish. CAUTION Do not use water when cleaning your fan. It could damage the motor or the finish and create the possibility of electrical shock. FP8014**-220 Exploded-View 1 Parts List Model #FP8014**-220 Ref. # Description Part # 1 Motor Assembly AMA8014** Timber Tripod Legs AP801420** 3 Hardware Bags Containing: 3/16-24x22 mm Screw Rubber Cap T-Wrench HDWFP8014** 2 How To Order Parts When ordering repair parts, always give the following information. Part Number Part Description Fan Model Number For repair parts: Phone au 3 NOTE: The illustration shown is not to scale. Actual configuration or finishes may vary. 5

6

7 Distributed in Australia by MyFan Pty Ltd Copyright 2012 Fanimation /03 V.01