MOBILE LAB UNITS 4111, 4121, 4222, 4342, 4332, 4352, 4101, 4401, 4751, 4901, 5201, 4741, 4701, 5301 SERIES (OAK OR MAPLE) ASSEMBLY INSTRUCTIONS

Transcription

1 4111, 4121, 4222, 4342, 4332, 4352, 4101, 4401, 4751, 4901, 5201, 4741, 4701, 5301 SERIES (OK OR MPLE) 1. MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: SCLE: 1 OF 5 REV K:\DIVERSIFIED\\CD\MOBILE LBS.dwg, 11/22/2016 1:56:26 PM, DWG To PDF.pc3

2 TOOLS REQUIRED 1 2 " WRENCH DJUSTBLE PLIERS SCREW DRIVER SSEMBLY COMPONE ITEMS INCLUDED PRT # PRT QTY CSTERS CSTER,4IN SWIVEL TOP PLTE, W/BRKE 4 CSTER HRDWRE KIT CSTER,SSY,HDWRE,16SCREWS, 16NUTS EXTENSION CORD ELECTRICL EXTENSION CORD 1 HND PUMP PUMP,ROCKET HND RP800 1 TUBING TUBING, 3 8 FOR HND PUMP 2.5 CROSS BR ROD,CROSSBR 1 2 DI.X 40L 1 UPRIGHTS ROD,UPRIGHT 3 4 DI.X 40L 2 CLMPS ROD CLMP 1 2X 3 4 SSY 2 WTER JUGS WTER JUG,2 1/2 GL RECTNGULR 2 GOOSE NECK FIXTURE FIXTURE,L08155WS GSNCK W/ FLNGE COMPONE VRY WITH STYLE OF MOBILE CBINET PURCHSED. : : TOOLS ND SSEMBLY COMPONE CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: SCLE: 2 OF 5 REV K:\DIVERSIFIED\\CD\MOBILE LBS.dwg, 11/22/2016 1:56:34 PM, DWG To PDF.pc3

3 GOOSE NECK FIXTURE HND PUMP DOORS ND BOTTOM DRWER REMOVED TO SHOW CLRITY 4332 UNIT SHOWN WITH HND PUMP DOORS REMOVED TO SHOW CLRITY 4352 UNIT SHOWN WITH GOOSE NECK FIXTURE DOORS REMOVED TO SHOW CLRITY STEP 1: LY CBINET ON BCK. REMOVE BOTTOM DRWER (IF NECESSRY). TTCH CSTERS FROM INSIDE OF THE CBINET USING THE HRDWRE PROVIDED. IF YOUR CBINET DOES NOT HVE HND PUMP, WTER FIXTURE, OR UPRIGHTS ND CROSSBR, SKIP TO STEP 6. STEP 2: SCREW THE HND PUMP OR WTER FIXTURE TO THE TOP OF LB USING THE PILOT HOLES IN THE TOP WITH SCREWS PROVIDED. TTCH ONE END OF THE 3 8" TUBING TO THE PUMP OR WTER FIXTURE ND INSERT THE OTHER END IN THE FRESH WTER CONTINER (NOT SHOWN). REMOVE SINK STOPPER FROM THE BOTTOM OF THE PLSTIC SINK DRIN HOSE ND PUT INTO THE SINK DRIN. INSERT THE END OF THE HOSE INTO THE WSTE WTER CONTINER (NOT SHOWN). 1. TO REMOVE SLIDING DOORS SLIDE DOORS TO ONE SIDE. REMOVE EXPOSED SCREWS FROM TOP RIL. SLIDE DOORS TO OPPOSITE SIDE ND REMOVE REMINING SCREWS. TILT DOORS ND RIL OUT. REPET STEPS BOVE IN REVERSE TO PUT DOORS BCK ON. CRETED NME : : THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: SCLE: 3 OF 5 REV K:\DIVERSIFIED\\CD\MOBILE LBS.dwg, 11/22/2016 1:56:39 PM, DWG To PDF.pc3

4 ROD SOCKETS THUMB SCREW CROSS BR ROD CLMP DOORS ND BOTTOM DRWER REMOVED TO SHOW CLRITY RIGHT UPRIGHT SHOWN, LEFT UPRIGHT NOT SHOWN COMPLETE UNIT SHOWN STEP 3: STEP 4: STEP 5: STEP 6: INSERT THE TPERED END OF THE TWO UPRIGHTS INTO THE ROD SOCKETS IN THE LB TOP. SLIDE THE ROD CLMPS OVER ONE OF THE UPRIGHTS ND TIGHTEN IN DESIRED LOCTION USING THUMB SCREWS PROVIDED ON CLMPS. REPET ON OTHER UPRIGHT. SLIDE CROSS BR THROUGH ONE OF THE CLMPS. POSITION OTHER SIDE THROUGH THE OTHER CLMP. SOME ROD CLMP DJUSTME MY BE REQUIRED. IF YOU HVE MIRROR/MRKER BORD, SEE MIRROR/MRKER BORD FOR PROPER INSTLLMENT. PUT DRWERS BCK IN ND PLCE CBINET IN DESIRED LOCTION. 1. RECOMMENDED CLENING INSTRUCTIONS FTER EVERY USE : EMPTY CLEN ND WSTE JUGS. RINSE WITH MILD NTI BCTERIL SOP. RUN MILD NTI BCTERIL SOP THROUGH WTER LINES ND HND PUMP TO INSURE NO BCTERIL BUILD UP. CRETED NME : : THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT DRWING NUMBER: SCLE: 4 OF 5 REV K:\DIVERSIFIED\\CD\MOBILE LBS.dwg, 11/22/2016 1:56:44 PM, DWG To PDF.pc3

5 TROUBLESHOOTING YOUR GFCI ELECTRICL RECEPTCLE: PLESE THROUGHOUT NY OF THE FOLLOWING STEPS (PROCEDURES); IF YOU RE NOT SURE YOU CN DO THIS JOB SFELY, ND COMPETENTLY, REFER THIS WORK TO QULIFIED PROFESSIONL! If your unit comes equipped with a GFCI (Ground Fault Circuit Interrupter) electrical receptacle, and there is no power in the receptacle please consider/check the following: The extension cord (if being used) is working properly. The breaker hasn t been tripped, or turned off. This type of GFCI has two testingrelated buttons on it. One button is appropriately labeled TEST, and the other button is labeled RESET. To test the GFCI receptacle follow these steps: Plug in an appliance (lamp or night light) into the outlet. The light should now be on. Then press the TEST button on the GFCI. The GFCI RESET button should pop out, and the light should go out. If the RESET button pops out, but the light doesn t go out, the GFCI has been improperly wired. In this case please contact a certified professional. There may also be a problem with other wiring in the same circuit. If the RESET button doesn t pop out, the GFCI is defective, or malfunctioned, and should be replaced. If the GFCI is functioning properly, and the lamp goes out, press the RESET button to restore power to the outlet. Conversely, if you have a GFI that has tripped (which is common) and it will not reset, you may have a wiring short in the circuit, a defective appliance on the circuit, or the GFI itself has become defective. To test a tripping GFCI follow these steps: Remove every appliance connected to the GFCI's circuit and reset it. If it doesn't reset there may either be a wiring fault behind a socket outlet, or your GFCI itself has become faulty. Make sure whatever you are plugging into to the GFCI is dry and not damaged. Only plug in one item at a time. If you are plugging in a defective item it will cause the GFCI to trip, and that item therefore should be replaced. If you are still having difficulty the easiest way to troubleshoot a GFI is to obtain a GFI tester, which is available at most hardware stores. It plugs into the GFI outlet, and will supply you with a "snapshot" of your connections, indicating wiring problems and/or the condition of the GFI. nother way to troubleshoot is to simply purchase a new GFI and install it.