- cooling operation - built-in heat meter - electronic circulating pumps

Transcription

1 -PN Brine to Water heat pump with domestic hot water tank 4,6-10,9 kw with R407c refrigerant The HAUTEC series may be used in conjunction with different heat sources such as geothermal probes or geothermal collector. The HAUTEC models are for space heating and hot water generating in residential and commercial buildings. The HAUTEC heat pumps are constructed to run especially quietly. All models may be delivered for cooling in summer as option. Besides optimum economic efficiency, a maximum in residential comfort, the heat pump incorporates the new HAUTEC heat pump controller especially developed for heat pump applications. The operator has full control of all functions of his heating system. The built-in ready for use HAUTEC source and heating kits and electric heating element reduce the on site assembly costs. Hot water generation is achieved into the hot water tank under the heat pump via an internal coil heat exchanger. The compact construction method has a small footprint, using very little floor space. The heat pump has a high efficiency compressor, suction gas cooled with 2 stainless steel plate heat exchangers, one for the heating circuit and one for the source circuit. It is built on a proven Hautec chassis in a sound insulated housing. The brine- and heating circulating pumps, the hot water priority switch and the electric heating element are built-in, ready for operation. The pre-wired heat pump is controlled with weather compensation and is supplied with a separate remote control. Configuration: - The integrated domestic hot water tank below the heat pump has a volume of 200 l capable of providing 340 l at 40 C (after blending) - built-in heat pump controller with plain text display - mixing circuit control ( temperature sensor must be ordered separately) - high efficiency - built-in electric heating element - easy assembly and easy operation - built-in hot water priority switch - easy transportation in two parts - built-in circulating pump for heat circuit - built-in circulating pump for brine circuit - built-in pressure transmitter (depending on the version) - flow temperature: R407c max 65 C Optional: - cooling operation - built-in heat meter - electronic circulating pumps HAUTEC comfort heat pump controller HSC1WPC, microprocessor controlled with weather compensation. It can control up to 2 heat generators for heating and domestic hot water and optional cooling, including 1 mixing circuit. Conditions: Output related switch of first heat generator (compressor), which can be operated in two power levels and additional 2nd heat generator ( e.g. electric heating element). Digital clock with perpetual calendar, clock change summer/winter time, several adjustable clocktimer programs, separate counting of operation hours and number of starts for every heat generator, plain text display. Showing the flow and return temperature of the heating system and source entrance and exit temperatures, outside and inside temperatures. Easy handling with two buttons and error diagnostics. With the master remote control it is possible to display up to 14 temperature values. Depending on the system configuration 4-8 of these will be available for use. Optional: Radio clock module, remote control with space temperature sensor, diagnostic module for data trasmission to a PC. HAUTEC digital remote control with plain text display and space temperature sensor to adjust the time, heating mode, automatic programs, holiday program or party mode. With the remote control the main values can be read out. A button for showing error messages, operation hours and number of starts for every heat generator, flow and return temperature of the heating system, source entrance and exit temperatures, outside and inside temperatures. The technican can use it as a master remote control to get other important information such as temperature and low and high pressure of the refrigerant circuit. Page 30 of 146

2 Source -PN Brine to Water heat pump with domestic hot water tank4,6-10,9 kw with R407c refrigerant Top view Heating flow 2 Heating return 3 Source inflow 4 Source exit TS Transport bracket Front view Side view Back view Heat pump Heating 1 3 TS Heating flow Cold water Circulation Hot water Heating return PN Page 31 of 146

3 -PN Brine to Water heat pump with domestic hot water tank4,6-10,9 kw with R407c refrigerant Type PN 219K PN 225K Refrigerant R407c R407c R407c R407c R407c PN 232K PN 235K Refrigerant filling weight kg 1,05 1,15 1,25 1,40 1,50 Compressor Oil (Polyol-Ester SEZ 68) kg 0,9 1,5 1,5 1,5 1,5 Primary-source (Brine-water) x x x x x Setting-up inside / outside + / - + / - + / - + / - + / - HEATING capacity B5/W35 kw 5,6 7,6 9,5 10,7 12,8 Coefficient of performance B5/W35 5,0 5,3 5,4 5,0 5,2 HEATING capacity B0/W35 (EN 255) kw 4,7 6,4 8,1 9,1 11,1 Power consumption B0/W35 (EN 255) kw 1,04 1,38 1,70 2,00 2,39 Coefficient of performance B0/W35 (EN 255) 4,5 4,6 4,8 4,5 4,6 HEATING capacity B0/W35 (EN 14511) kw 4,6 6,3 7,9 8,9 10,9 Power consumption B0/W35 (EN 14511) kw 1,07 1,42 1,74 2,05 2,52 Coefficient of performance B0/W35 (EN 14511) 4,3 4,4 4,5 4,3 4,3 HEATING capacity B0/W50 (EN 255) kw 3,6 5,0 6,6 7,4 9,3 Coefficient of performance B0/W50 (EN 255) 3,4 3,5 3,7 3,5 3,6 Coefficient of performance B0/W50 (EN 14511) 3,3 3,3 3,5 3,3 3,4 COOLING capacity B20 (Flow16 C / Return 21 C) kw 4,6 6,6 7,9 9,8 10,7 Power consumption B20 (Flow16 C / Return 21 C) Coefficient of performance B20 (Flow 16 C / Return 21 C) EER 4,3 4,6 4,6 4,9 4,6 SOURCE minimal volume flow (at 5K) m³/h 0,73 1,01 1,30 1,44 1,75 SOURCE nominal volume flow (at 3K) m³/h 1,21 1,69 2,17 2,41 2,92 SOURCE internal pressure drop (at 3K) hpa SOURCE connection dimensions Inch SOURCE entrance brine minimal C SOURCE entrance brine maximal C SOURCE frost resistance brine C SOURCE volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 2,2 HEATING minimal volume flow (at 10K) m³/h 0,40 0,55 0,70 0,79 0,95 HEATING nominal volume flow (at 5K) m³/h 0,80 1,10 1,40 1,57 1,90 HEATING internal pressure drop (at 5K) hpa HEATING connection dimensions Inch HEATING flow temperature minimal C HEATING flow temperature temporary maximal C HEATING volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 2,2 Nominal voltage V Number of phases 1~ 3~ 3~ 3~ 3~ Frequency Hz Nominal current A 5,1 2,2 3,7 4,1 4,7 cos φ 0,9 0,9 0,7 0,7 0,7 Starting current A <30 <30 <30 <30 <30 Starting current (limited) Fuse (delay) A 20 3x16 3x16 3x16 3x20 Protection class IP 21 IP 21 IP 21 IP 21 IP 21 Sound power level (EN 12102) db(a) Measurement height mm Measurement width mm Measurement depth mm Weight kg A PN 242K All technical data were determined according to EN 255 and EN The electric heating element is to be secured depending on the power input. - 3 kw / 230V~/N/PE Fuse 1x16A - 9 kw / 400V~3/N/PE Fuse 3x16A - 18 kw / 400V~3/N/PE Fuse 3x35A As an antifreeze HAUTEC Frostcare is to be used. Other antifreezes and brines on inquiry. A change-over of the refrigerant circuit (heating / cooling) is available for all devices. Subject to technical modifications. Page 32 of 146

4 -PN Brine to Water heat pump with domestic hot water tank4,6-10,9 kw with R407c refrigerant -PN R407c with 3 years cooling circle material warranty 1 product code WP order number heating capacity [kw] -PN -PN -PN -PN -PN B5/W35 B0/W35 219K 225K 232K 235K 242K -PN-219K² 88SV219AHBPN5 5,6 4, ,- -PN-225K² 88SV2251HBPN5 7,6 6, ,- -PN-232K 88SV2321HBPN5 9,5 7, ,- -PN-235K² 88SV2361HBPN5 10,7 8, ,- -PN-242K 88SV2431HBPN5 12,8 10, ,- heat pump controller 5 and remote control ready for operation, urgent neccessary and pre-programmed heat pump controller with remote control 1.302, , , , ,- Total with controller 7.000, , , , ,- The obstructed kits for the Brine and heating circles can be equipped against surcharge with electronic pumps (see page 135/136). Surcharge for exchange of multi-level source pump against electronic source pump 270,- 270,- 270,- 270,- 270,- Surcharge for exchange of multi-level circulating heating pump against electronic circulating heating pump 270,- 270,- 270,- 270,- 270,- Accessories - (optional). Further information in the accessories list connecting kit with reinforced hoses (supplied as separate unit) HWAS01L 89WA00100H0ND 148,- 148,- 148,- 148,- 148,- Heating-cooling, refrigerant circuit switching to active cooling, inclusive controller modification (built-in and ready for operation) HWU-HK01 89HK00100H0ND 1.695, , , , ,- HWU-HK02 89HK00200H0ND HAUTEC heat exchanger for passive cooling inclusive product modification (supplied as separate unit) HPK01 89PK00100H0ND 1.477, , , , ,- HPK02 89PK00200H0ND HAUTEC heat-meter (supplied as separate unit) HWME01 89WME0100H0ND 175,- 175,- 175,- 175,- 175,- HAUTEC temperature sensor for mixing circuit control (supplied as separate unit) HMKF01 89MKF0001H0ND 25,- 25,- 25,- 25,- 25,- When ordering please use product code e.g.: -PN-235K with order number. 1) The warranty for parts of refrigerant circuit comes into effect only if the equipment is used for its intended purpose and the installation and commisioning have been examinated and approved of an authorized HAUTEC customer service technician. An extended warranty of 2 years is available (refrigerant circuit) for a surcharge of 2% on the selected equipment price. 2) Also available in 230V AC. See separate price list. Please check delivery time when ordering. 3) Source circulating pump is sufficient for e.g. HAUTEC double U pipe probes of maximum length of 50 m (each); mind the maximum pressure head. 4) For use with HELN - mind the maximum pressure head 5) The Hautec Heat Pump controller must be used with these models. More accessories may be found in the accessory section page 118 onwards. Page 33 of 146

5 HCW-PN Water to Water heat pump with domestic hot water tank 6,1 11,9 kw with R407c refrigerant The HAUTEC series may be used in conjunction with underground water as heat source. The HAUTEC models are for space heating and hot water generating in residential and commercial buildings. The HAUTEC heat pumps are constructed to run especially quietly. All models may be delivered for cooling in summer as option. Besides optimum economic efficiency, a maximum in residential comfort, the heat pump incorporates the new HAUTEC heat pump controller especially developed for heat pump applications. The operator has full control of all functions of his heating system. The built-in ready for use HAUTEC source and heating kits and electric heating element reduce the on site assembly costs. Hot water generation is achieved into the hot water tank under the heat pump via an internal coil heat exchanger. The compact construction method has a small footprint, using very little floor space. The heat pump has a high efficiency compressor, suction gas cooled with 2 stainless steel plate heat exchangers, one for the heating circuit and one for the source circuit. It is built on a proven Hautec chassis in a sound insulated housing. The brine- and heating circulating pumps, the hot water priority switch and the electric heating element are built-in, ready for operation. The pre-wired heat pump is controlled with weather compensation and is supplied with a separate remote control. Configuration: - The integrated domestic hot water tank below the heat pump has a volume of 200 l capable of providing 340 l at 40 C (after blending) - built-in heat pump controller with plain text display - mixing circuit control ( temperature sensor must be ordered separately) - high efficiency - built-in electric heating element - easy assembly and easy operation - built-in hot water priority switch - easy transportation in two parts - built-in circulating pump for heat circuit - built-in pressure transmitter (depending on the version) - flow temperature: R407c max 65 C Optional: - cooling operation - built-in heat meter - well pump wiring - electronic circulating pump HAUTEC comfort heat pump controller HSC1WPC, microprocessor controlled with weather compensation. It can control up to 2 heat generators for heating and domestic hot water and optional cooling, including 1 mixing circuit. Conditions: Output related switch of first heat generator (compressor), which can be operated in two power levels and additional 2nd heat generator ( e.g. electric heating element). Digital clock with perpetual calendar, clock change summer/winter time, several adjustable clocktimer programs, separate counting of operation hours and number of starts for every heat generator, plain text display. Showing the flow and return temperature of the heating system and source entrance and exit temperatures, outside and inside temperatures. Easy handling with two buttons and error diagnostics. With the master remote control it is possible to display up to 14 temperature values. Depending on the system configuration 4-8 of these will be available for use. Optional: Radio clock module, remote control with space temperature sensor, diagnostic module for data trasmission to a PC. HAUTEC digital remote control with plain text display and space temperature sensor to adjust the time, heating mode, automatic programs, holiday program or party mode. With the remote control the main values can be read out. A button for showing error messages, operation hours and number of starts for every heat generator, flow and return temperature of the heating system, source entrance and exit temperatures, outside and inside temperatures. The technican can use it as a master remote control to get other important information such as temperature and low and high pressure of the refrigerant circuit. Page 34 of 146

6 Source HCW-PN Water to Water heat pump with domestic hot water tank6,1 11,9 kw with R407c refrigerant Top view Heating flow 2 Heating return 3 Source inflow 4 Source exit TS Transport bracket Front view Side view Back view Heat pump Heating 1 3 TS Heating flow Cold water Circulation Hot water Heating return HCW-PN Page 35 of 146

7 HCW-PN Water to Water heat pump with domestic hot water tank6,1 11,9 kw with R407c refrigerant Type HCW PN 219K HCW PN 225K HCW PN 232K HCW PN 235K Refrigerant R407c R407c R407c R407c Refrigerant filling weight kg 1,10 1,20 1,30 1,45 Compressor Oil (Polyol-Ester SEZ 68) kg 0,9 1,5 1,5 1,5 Primary-source (Water-water) x x x x Setting-up inside / outside + / - + / - + / - + / - HEATING capacity W10/W35 (EN 255) kw 6,2 8,3 10,3 12,1 Power consumption W10/W35 (EN 255) kw 1,15 1,47 1,83 2,13 Coefficient of performance W10/W35 (EN 255) 5,4 5,6 5,6 5,7 HEATING capacity W10/W35 (EN 14511) kw 6,1 8,1 10,1 11,9 Power consumption W10/W35 (EN 14511) kw 1,16 1,50 1,87 2,20 Coefficient of performance W10/W35 (EN 14511) 5,3 5,4 5,4 5,4 HEATING capacity W10/W50 (EN 255) kw 5,4 7,0 8,8 10,2 Coefficient of performance W10/W50 (EN 255) 3,8 4,0 4,0 4,0 Coefficient of performance W10/W50 (EN 14511) 3,6 3,8 3,8 3,8 COOLING capacity W10 (Flow16 C / Return 21 C) kw 4,8 8,1 8,7 11,4 Power consumption W10 (Flow16 C / Return 21 C) Coefficient of performance W10 (Flow 16 C / Return 21 C) EER 5,2 6,6 5,4 6,4 SOURCE minimal volume flow (at 5K) m³/h 0,87 1,17 1,46 1,71 SOURCE nominal volume flow (at 3K) m³/h 1,45 1,96 2,44 2,85 SOURCE internal pressure drop (at 3K) hpa SOURCE connection dimensions Inch SOURCE entrance minimal C SOURCE entrance maximal C SOURCE volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 HEATING minimal volume flow (at 10K) m³/h 0,53 0,71 0,89 1,04 HEATING nominal volume flow (at 5K) m³/h 1,07 1,42 1,77 2,07 HEATING internal pressure drop (at 5K) hpa HEATING connection dimensions Inch HEATING flow temperature minimal C HEATING flow temperature temporary maximal C HEATING volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 Nominal voltage V Number of phases 1~ 3~ 3~ 3~ Frequency Hz Nominal current A 5,7 2,5 3,9 4,0 cos φ 0,9 0,8 0,7 0,8 Starting current A <30 <30 <30 <30 Starting current (limited) Fuse (delay) A 20 3x16 3x16 3x16 Protection class IP 21 IP 21 IP 21 IP 21 Sound power level (EN 12102) db(a) Measurement height mm Measurement width mm Measurement depth mm Weight kg A All technical data were determined according to EN 255 and EN The electric heating element is to be secured depending on the power input. - 3 kw / 230V~/N/PE Fuse 1x16A - 9 kw / 400V~3/N/PE Fuse 3x16A - 18 kw / 400V~3/N/PE Fuse 3x35A A change-over of the refrigerant circuit (heating / cooling) is available for all devices. With water-water heat pumps a water analysis is inevitably to make sure that the limit values are kept for the heat exchangers or to ascertain the necessity of an evaporator with higher resistance. The limit values are to be requested from HAUTEC. Subject to technical modifications. Page 36 of 146

8 HCW-PN Water to Water heat pump with domestic hot water tank6,1 11,9 kw with R407c refrigerant HCW-PN R407c with 3 years cooling circle material warranty 1 product code WP order number heating capacity W10/W35 [kw] HCW-PN 219K HCW-PN 225K HCW-PN 232K HCW-PN 235K HCW-PN-219K² 88WV219AHBPN5 6, ,- HCW-PN-225K² 88WV2251HBPN5 8, ,- HCW-PN-232K 88WV2321HBPN5 10, ,- HCW-PN-235K² 88WV2361HBPN5 11, ,- heat pump controller 5 and remote control ready for operation, urgent neccessary and pre-programmed heat pump controller with remote control 1.302, , , ,- Total with controller 6.761, , , ,- The obstructed kits for the Brine and heating circles can be equipped against surcharge with electronic pumps (see page 135/136). Surcharge for exchange of multi-level circulating heating pump against electronic circulating heating pump 270,- 270,- 270,- 270,- Accessories - (optional). Further information in the accessories list Connecting kit with reinforced hoses (supplied as separate unit) HWAS01L 89WA00100H0ND 148,- 148,- 148,- 148,- Well pump switch. It refers to the submersible pump (connected and ready for operation) 3) HBPA01 89BP00100H0ND 293,- 293,- 293,- 293,- Heating-cooling, refrigerant circuit switching to active cooling, inclusive controller modification (built-in and ready for operation) HWU-HK01 89HK00100H0ND 1.695, , , ,- HWU-HK02 89HK00200H0ND HAUTEC heat exchanger for passive cooling inclusive product modification (supplied as separate unit) HPK01 89PK00100H0ND 1.477, , , ,- HPK02 89PK00200H0ND HAUTEC heat-meter (supplied as separate unit) HWME01 89WME0100H0ND 175,- 175,- 175,- 175,- HAUTEC temperature sensor for mixing circuit control (supplied as separate unit) HMKF01 89MKF0001H0ND 25,- 25,- 25,- 25,- When ordering please use product code e.g.: -PN-235K with order number. 1) The warranty for parts of refrigerant circuit comes into effect only if the equipment is used for its intended purpose and the installation and commisioning have been examinated and approved of an authorized HAUTEC customer service technician. An extended warranty of 2 years is available (refrigerant circuit) for a surcharge of 2% on the selected equipment price. 2) Also available in 230V AC. See separate price list. Please check delivery time when ordering. 3) With water-water heat pumps a water analysis is neccessary. 4) For use with HELN - mind the maximum pressure head 5) The Hautec Heat Pump controller must be used with these models. More accessories may be found in the accessory section page 118 onwards. Page 37 of 146

9 -PK Brine to Water heat pump 4,6 14,0 kw with R407c refrigerant with an underbuilt domestic hot water tank and flanged separate hot water heat pump. The HAUTEC series may be used in conjunction with different heat sources such as geothermal probes or geothermal collector. The HAUTEC models are for space heating and hot water generating in residential and commercial buildings. The HAUTEC heat pumps are constructed to run especially quietly. All models may be delivered for cooling in summer as option. Besides optimum economic efficiency, a maximum in residential comfort, the heat pump incorporates the new HAUTEC heat pump controller especially developed for heat pump applications. The operator has full control of all functions of his heating system. The built-in ready for use HAUTEC source and heating kits and electric heating element reduce the on site assembly costs. Hot water generation is achieved into the hot water tank under the heat pump via a flange connected hot water heat pump HWBW K. The compact construction method has a small footprint, using very little floor space. The heat pump has a high efficiency compressor, suction gas cooled with 2 stainless steel plate heat exchangers, one for the heating circuit and one for the source circuit. It is built on a proven Hautec chassis in a sound insulated housing. The brine- and heating circulating pumps, the hot water priority switch and the electric heating element are built-in, ready for operation. The pre-wired heat pump is controlled with weather compensation and is supplied with a separate remote control. Configuration: - The integrated domestic hot water tank below the heat pump has a volume of 200 l capable of providing 340 l at 40 C (after blending) - built-in heat pump controller with plain text display - mixing circuit control ( temperature sensor must be ordered separately) - high efficiency - built-in electric heating element - easy assembly and easy operation - separate hot water heat pump - easy transportation in two parts - built-in soft starter (only type 260) - built-in circulating pump for heat circuit - built-in circulating pump for brine circuit - built-in pressure transmitter (depending on the version) - flow temperature: R407c max 65 C Optional: - cooling operation - built-in heat meter - electronic circulating pumps HAUTEC comfort heat pump controller HSC1WPC, microprocessor controlled with weather compensation. It can control up to 2 heat generators for heating and domestic hot water and optional cooling, including 1 mixing circuit. Conditions: Output related switch of first heat generator (compressor), which can be operated in two power levels and additional 2nd heat generator ( e.g. electric heating element). Digital clock with perpetual calendar, clock change summer/winter time, several adjustable clocktimer programs, separate counting of operation hours and number of starts for every heat generator, plain text display. Showing the flow and return temperature of the heating system and source entrance and exit temperatures, outside and inside temperatures. Easy handling with two buttons and error diagnostics. With the master remote control it is possible to display up to 14 temperature values. Depending on the system configuration 4-8 of these will be available for use. Optional: Radio clock module, remote control with space temperature sensor, diagnostic module for data trasmission to a PC. HAUTEC digital remote control with plain text display and space temperature sensor to adjust the time, heating mode, automatic programs, holiday program or party mode. With the remote control the main values can be read out. A button for showing error messages, operation hours and number of starts for every heat generator, flow and return temperature of the heating system, source entrance and exit temperatures, outside and inside temperatures. The technican can use it as a master remote control to get other important information such as temperature and low and high pressure of the refrigerant circuit. Page 38 of 146

10 Source -PK Brine to Water heat pump 4,6 14,0 kw with R407c refrigerant with an underbuilt domestic hot water tank and flanged separate hot water heat pump. Top view Front view Side view 1 Heating flow 2 Heating return 3 Source inflow 4 Source exit TS Transport bracket Back view Heat pump 900 TS Heating Heating flow Cold water Circulation Hot water Heating return HCW-PK Page 39 of 146

11 -PK Brine to Water heat pump 4,6 14,0 kw with R407c refrigerant with an underbuilt domestic hot water tank and flanged separate hot water heat pump. Type PK 219K PK 225K PK 232K PK 235K PK 242K PK 248K PK 260K Refrigerant R407c R407c R407c R407c R407c R407c R407c Refrigerant filling weight kg 1,05 1,15 1,25 1,40 1,50 1,55 1,65 Compressor Oil (Polyol-Ester SEZ 68) kg 0,9 1,5 1,5 1,5 1,5 1,5 2,2 Primary-source (Brine-water) x x x x x x x Setting-up inside / outside + / - + / - + / - + / - + / - + / - + / - HEATING capacity B5/W35 kw 5,6 7,6 9,5 10,7 12,8 13,7 15,9 Coefficient of performance B5/W35 5,0 5,3 5,4 5,0 5,2 5,3 5,1 HEATING capacity B0/W35 (EN 255) kw 4,7 6,4 8,1 9,1 11,1 11,9 14,3 Power consumption B0/W35 (EN 255) kw 1,04 1,38 1,70 2,00 2,39 2,46 3,14 Coefficient of performance B0/W35 (EN 255) 4,5 4,6 4,8 4,5 4,6 4,8 4,6 HEATING capacity B0/W35 (EN 14511) kw 4,6 6,3 7,9 8,9 10,9 11,6 14,0 Power consumption B0/W35 (EN 14511) kw 1,07 1,42 1,74 2,05 2,52 2,51 3,18 Coefficient of performance B0/W35 (EN 14511) 4,3 4,4 4,5 4,3 4,3 4,6 4,4 HEATING capacity B0/W50 (EN 255) kw 3,6 5,0 6,6 7,4 9,3 10,0 13,3 Coefficient of performance B0/W50 (EN 255) 3,4 3,5 3,7 3,5 3,6 3,6 3,3 Coefficient of performance B0/W50 (EN 14511) 3,3 3,3 3,5 3,3 3,4 3,4 3,1 Heating capacity HWBW-K W20/W45 kw 1,6 1,6 1,6 1,6 1,6 1,6 1,6 Coefficient of performance COP >4 >4 >4 >4 >4 >4 >4 COOLING capacity B20 (Flow16 C / Return 21 C) kw 4,6 6,6 7,9 9,8 10,7 11,5 15,2 Power consumption B20 (Flow16 C / Return 21 C) Coefficient of performance B20 (Flow 16 C / Return 21 C) EER 4,3 4,6 4,6 4,9 4,6 4,6 4,8 SOURCE minimal volume flow (at 5K) m³/h 0,73 1,01 1,30 1,44 1,75 1,90 2,28 SOURCE nominal volume flow (at 3K) m³/h 1,21 1,69 2,17 2,41 2,92 3,17 3,76 SOURCE internal pressure drop (at 3K) hpa SOURCE connection dimensions Inch SOURCE entrance brine minimal C SOURCE entrance brine maximal C SOURCE frost resistance brine C SOURCE volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 2,2 2,5 2,5 HEATING minimal volume flow (at 10K) m³/h 0,40 0,55 0,70 0,79 0,95 1,02 1,23 HEATING nominal volume flow (at 5K) m³/h 0,80 1,10 1,40 1,57 1,90 2,04 2,46 HEATING internal pressure drop (at 5K) hpa HEATING connection dimensions Inch HEATING flow temperature minimal C HEATING flow temperature temporary maximal C HEATING volume heat exchanger (water-side) l 1,1 1,3 1,7 1,9 2,2 2,2 2,5 Nominal voltage V Number of phases 1~ 3~ 3~ 3~ 3~ 3~ 3~ Frequency Hz Nominal current A 5,1 2,2 3,7 4,1 4,7 4,8 6,5 cos φ 0,9 0,9 0,7 0,7 0,7 0,7 0,7 Starting current A <30 <30 <30 <30 < Starting current (limited) A 19 Fuse (delay) A 20 3x16 3x16 3x16 3x20 3x20 3x25 Protection class IP 21 IP 21 IP 21 IP 21 IP 21 IP 21 IP 21 Sound power level (EN 12102) db(a) Measurement height mm Measurement width mm Measurement depth mm Weight kg All technical data were determined according to EN 255 and EN The electric heating element is to be secured depending on the power input. - 3 kw / 230V~/N/PE Fuse 1x16A - 9 kw / 400V~3/N/PE Fuse 3x16A - 18 kw / 400V~3/N/PE Fuse 3x35A As an antifreeze HAUTEC Frostcare is to be used. Other antifreezes and brines on inquiry. A change-over of the refrigerant circuit (heating / cooling) is available for all devices. Subject to technical modifications. Page 40 of 146

12 -PK Brine to Water heat pump 4,6 14,0 kw with R407c refrigerant with an underbuilt domestic hot water tank and flanged separate hot water heat pump. -PK R407c for heating with 3 years cooling circle material warranty 1 with separate hot water heat pump flange connected HWBW K with refrigeration R134a ready for operate with 2 years cooling circle material warranty 1 hot water temperature temporarly up to 65 C product code WP order number heating capacity [kw] B5/W35 B0/W35 -PK 219K -PK 225K -PK 232K -PK 235K -PK 242K -PK 248K -PK 260K -PK-219K² 88SU219AHBPN5 5,6 4,6 1, ,- -PK-225K² 88SU2251HBPN5 7,6 6,3 1, ,- -PK-232K 88SU2321HBPN5 9,5 7,9 1, ,- -PK-235K² 88SU2361HBPN5 10,7 8,9 1, ,- -PK-242K 88SU2431HBPN5 12,8 10,9 1, ,- -PK-248K² 88SU2491HBPN5 13,7 11,6 1, ,- -PK-260K² 88SU2601SBPN5 15,9 14,0 1, ,- heat pump controller 5 and remote control ready for operation, urgent neccessary and pre-programmed heat pump controller with remote control 1.302, , , , , , ,- Total with Controller 8.385, , , , , , ,- The obstructed kits for the Brine and heating circles can be equipped against surcharge with electronic pumps (see page 135/136). Surcharge for exchange of multi-level source pump against electronic source pump 270,- 270,- 270,- 270,- 270,- 320,- 320,- Surcharge for exchange of multi-level circulating heating pump against electronic circulating heating pump 270,- 270,- 270,- 270,- 270,- 320,- 320,- Accessories - (optional). Further information in the accessories list Kit for integration an hot water generating modul in the underfloor heating return (Supplied as separate unit) HEQ01 89EQ00100H0ND 108,- 108,- 108,- 108,- 108,- 108,- 108,- connecting kit with reinforced hoses (supplied as separate unit) HWAS01L 89WA00100H0ND 148,- 148,- 148,- 148,- 148,- 148,- 148,- Heating-cooling, refrigerant circuit switching to active cooling, inclusive controller modification (built-in and ready for operation) HWU-HK01 89HK00100H0ND 1.695, , , , ,- HWU-HK02 89HK00200H0ND 1.861, ,- HAUTEC heat exchanger for passive cooling inclusive product modification (supplied as separate unit) HPK01 89PK00100H0ND 1.477, , , , ,- HPK02 89PK00200H0ND 1.855, ,- HAUTEC heat-meter (supplied as separate unit) HWME01 89WME0100H0ND 175,- 175,- 175,- 175,- 175,- 175,- 175,- HAUTEC temperature sensor for mixing circuit control (supplied as separate unit) HMKF01 89MKF0001H0ND 25,- 25,- 25,- 25,- 25,- 25,- 25,- When ordering please use product code e.g.: -PN-235K with order number. 1) The warranty for parts of refrigerant circuit comes into effect only if the equipment is used for its intended purpose and the installation and commisioning have been examinated and approved of an authorized HAUTEC customer service technician. An extended warranty of 2 years is available (refrigerant circuit) for a surcharge of 2% on the selected equipment price. 2) Also available in 230V AC. See separate price list. Please check delivery time when ordering. 3) Source circulating pump is sufficient for e.g. HAUTEC double U pipe probes of maximum length of 50 m (each); mind the maximum pressure head. 4) For use with HELN - mind the maximum pressure head 5) The Hautec Heat Pump controller must be used with these models. 6) The HWBW K is useable only in connection with underflor heating system (min 80 square meters must be constantly opened) More accessories may be found in the accessory section page 118 onwards. Page 41 of 146