SHOP EQUIPMENT ELECTRONIC REPAIR SEMI-TRAILER MOUNTED (NSN )

Transcription

1 TM &P TECHNICAL MANUAL OPERATOR' S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LISTS FOR SHOP EQUIPMENT ELECTRONIC REPAIR SEMI-TRAILER MOUNTED (NSN ) HEADQUARTERS, DEPARTMENT OF THE ARMY

2 The following summary However, all warnings is adapted from Warnings within the manual. should be observed as noted in the text. WARNING Dangerous voltages, capable of causing death, are present in this vehicle, and the equipment provided in its tool load. Use extreme caution when handling, testing, or adjusting any electrical equipment. -- Ground the vehicle and instruments prior to operation. - - Do not operate in an explosive atmosphere. -- Keep away from live circuits. -- Do not service or adjust alone. -- Do not substitute or modify parts or equipment. WARNING HEARING PROTECTION REQUIRED WHEN OPERATING - Electric Drill - Vacuum Cleaner WARNING Dangerous chemical solvents are used with this equipment. Avoid prolonged breathing of vapors; insure that there is adequate ventilation at all times. Avoid skin contact. Wash hands immediately after contact with solvent. If solvent gets into your eyes, flush your eyes immediately with clean water. Seek medical attention if necessary.

3 TM &P C CHANGE NO. HEADQUARTERS DEPARTMENT OF THE ARMY WASHINGTON, DC 5 SEPTEMBER 99 Operator s, Organizational, Direct Support and General Support Maintenance Manual Including Repair Parts Lists for SHOP EQUIPMENT, ELECTRONIC REPAIR SEMI-TRAILER MOUNTED (NSN ) TM &P, 8 June 984, is changed as indicated below: NOTE New or changed text is indicated by a change bar at the outer margin of the page and the designation "Change " at the bottom of the page next to the page number. On pages with this designation but without the change bar, the entire page is new or changed.. Remove old pages and insert new pages as follows: Remove Pages Insert Pages iii and iv iii and iv /(- blank) - thru. File this change sheet in back of the publication for reference purposes.

4 By Order of the Secretary of the Army: GORDON R. SULLIVAN General, United States Army chief of Staff MILTON H. HAMILTON Administrative Assistant to the Secretary of the Army 073 DISTRIBUTION: TO BE DISTRIBUTED IN ACCORDANCE. WITH DA FORM -5-E, (BLOCK 743), REQUIREMENTS FOR TM &P.

5 TM &P Technical Manual HEADQUARTERS DEPARTMENT OF THE ARMY No &P Washington, DC 8 June 984 OPERATOR'S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LIST FOR SHOP EQUIPMENT, ELECTRONIC REPAIR SEMI-TRAILER MOUNTED (NSN ) REPORTING OF ERRORS You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail you letter, DA Form 08 (Recommended Changes to Publications and Blank Forms), or DA Form 08-, located in the back of this manual direct to: Commander, US Army Armament, Munitions and Chemical Command, ATTN: DRSMC-MAS, Rock Island, IL A reply will be furnished directly to you. i

6 TM &P INSTRUCTIONS FOR REQUISITIONING PARTS NOT IDENTIFIED BY NSN When requisitioning parts not identified by National Stock Number, it is mandatory that the following information be furnished the supply officer. - Manufacturer s Federal Supply Code Number -. - Manufacturer s Part Number exactly as listed herein. 3 - Nomenclature exactly as listed herein, including dimensions, if necessary. 4 - Manufacturer s Model Number Manufacturer s Serial Number (End Item). 6 - Any other information such as Type, Frame Number, and Electrical Characteristics, if applicable. 7 - If DD Form 348 is used, fill in all blocks except 4, 5, 6, and Remarks field in accordance with AR Complete Form as Follows: (a) In blocks 4, 5, 6, list manufacturer s Federal Supply Code Number - followed by a colon and manufacturer s Part Number for the repair part. (b) Complete Remarks field as follows: Noun: (nomenclature or repair part) For: NSN : Manufacturer: Boyertown Auto Body Works Third and Walnut Streets Boyertown, PA 95 Model: Serial: (of end item) Any other pertinent information such as Frame Number, Type, Dimensions, etc. ii

7 TM &P Table of Contents Title Page Requisitioning Parts Table of Contents List of Illustrations Section. Introduction General Semitrailer Warranty Maintenance Forms and Records Administrative Storage Equipment Serviceability Criteria Destruction of Army Materiel to Prevent Enemy Use Quality Assurance/Quality Control Reporting Quality Deficiency Reports..... Description and Data Section. Operating Instructions Semitrailer M447C Tools and Equipment Load Operator/Crew Preventive Maintenance Checks and Services (PMCS) Section 3. Maintenance Instructions Reference Instructions Repair Parts Fire Extinguisher and Bracket First Aid Kit Data Plates Stools Clock Small Parts Cabinet TOOl BOX (appendix A) Front Workbench Battery Charger Machinist s Vice Utility Grinding Machine Frequency Convertor & Sweep Oscillator Electronic Cases Oscilloscope Electronic Case DC Power Supply Ground Rod and Upright Broom Left and Right Side Workbench Electrical Installation Tools and Equipment Section 4. Component List, Tools and Equipment Component Location Tools and Equipment List Appendix A. References Paragraph Page i ii iii iv A- Change iii

8 TM &P Figure FO- List of Illustrations Title Major component location Rear wall mounted equipment Front wall mounted equipment Battery charger and machinist's vise Disconnecting and removing utility grinding machine.. Electronic cases and power supply mounting Ground rod and upright broom Left and right side workbench Distribution panel Rear crossover conduit Right side workbench and bench grinder conduit.... Left side workbench conduit Front workbench conduit DC power supply conduit Ceiling outlet wiring Inst. - Frequency convertor Inst. - Sweep oscillator Inst. - Oscilloscope Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Inst. - Drawer no Wiring diagram Page FO- iv

9 TM &P Section. INTRODUCTION -. General. This manual is intended as a guide for users of the electronic repair shop set manufactured in accordance with ARRCOM drawing F37E800, revision B, dated 0 December 980, and loaded with tools and equipment in accordance with set components list SC CL-B06 and SC CL-B06-HR, dated 3 October Semitrailer. a. The shop set is installed in a semitrailer, van, shop, folding sides, 6 ton, 4-wheel, Model M447C, NSN b. Refer to the M447C reference data sheets in regard to the physical characteristics of the semitrailer and TM &P for operation and maintenance procedures and TM &P for parts. -3. Warranty. The shop set and semitrailer are warranted for a period of one year from the date of manufacture. All warranty problems should be referred to the manufacturer. -4. Maintenance Forms and Record, Equipment maintenance forms and procedures for their use are contained in DA PAM as contained in Maintenance Management Update. -5. Administrative Storage. For information necessary to meet administrative storage requirements refer to TM Equipment Serviceability Criteria (ESC). There are no equipment serviceability criteria (ESC) technical manuals in existence pertinent to the end item of equipment being covered in this publication. -7. Destruction of Army Material to Prevent Enemy Use. For procedures required to render this end item unusable by the enemy refer to TM Quality Assurance/Quality Control (QA/QC). a. Refer to MIL-STD-09 and MIL-M for QA/QC terms and definitions. b. Refer to TM &P and DMWR for the applicable QA/QC requirements. -9. Reporting Quality Deficiency Reports (QDR). QDRs will be prepared on SF 368, Quality Deficiency Report. Instructions for preparing QDRs are provided in DA PAM as contained in Maintenance Management Update. QDRs should be mailed directly to: Commander, US Army Armament, Munitions and Chemical Command, ATTN: DRSMC-MAO (R), Rock Island, IL 699. A reply will be furnished directly to you. -

10 TM &P -0. Description and Data. 4&P : For description of the semitrailer van refer to TM b. For major component location on shop set van refer to figure. Identification plate. The US Army identification is located on the curbside front panel of the van body (see fig ). It contains the information listed below: Part No. - 37E800 NSN Manufacturer - Facility Code - (FSCM) Serial No. - G-85- Date of Manufacture - Warranty - year Contract No. - DAAA09-8-C-40 -

11 TM &P Figure. Major component location. ITEM NAME Semitrailer Workbench, Front 3 Workbench, Left Side 4 Workbench, Right Side 5 Equipment Installation 6 Stowage Assembly 7 Electrical Instillation 8 Nameplate, Identification QTY PART NUMBER 37E800 37E88 37E E B E875 37E800- (FSCM) () () () () () (907) () () -3/(-4 blank)

12 TM &P Section. OPERATING INSTRUCTIONS -. Semitrailer - M447C. a. Operation of the M447C semitrailer is covered by TM &P. Refer to that technical manual for information. b. Maintenance, cleaning, lubrication, troubleshooting, and performance verifications are covered by TM &P. Refer to that technical manual for information. -. Tools and Equipment Load. CAUTION This equipment is not suppressed for electromagnetic interference. DO NOT operate within 00 feet of sensitive electronic communications and surveillance equipment. a. Operation, maintenance, cleaning, lubrication, troubleshooting, and performance verifications for the electrical and electronic equipment is covered in their respective operator s manuals. Please refer to appendix A of this manual for the list of technical manuals provided with this shop set. b. Installation and removal of the tools and equipment load is covered in section 4 of this manual. -3. Operator/Crew Preventive Maintenance Checks and Services (PMCS). a. General. () Perform area or Before You Operate. Always keep in mind the CAUTIONS and WARNINGS. your "Before" PMCS prior to the equipment leaving its containment performing its intended mission. () While You Operate. Always keep in mind the CAUTIONS and WARNINGS. Perform your "During" PMCS when the equipment is being used in its intended mission. (3) After You Operate. Be sure to perform your "After" PMCS after the equipment has been taken out of its mission mode or returned to its containment area. (4) If Your Equipment Fails to Operate. Troubleshoot with proper equipment. Report any deficiencies using the proper forms and procedures. See DA Pam b. PMCS Procedures. () Table - lists the inspections and care of your equipment required to keep it in good operating condition. Change -

13 TM &P () The "interval" column tells you when to do a certain check or service. (3) The "location" column tells you where in the shop set the check or service is performed. (4) The "procedure" column tells you how to do the required checks and services. Carefully follow these instructions. If you do not have the tools, or if the procedure tells you to, have organizational maintenance do the work. NOTE The term "mission capable" means that the equipment is on hand and ready to performs its combat missions (see AR ). (5) The Not Fully Mission Capable If: column tells you when the shop set is non-mission capable and why. (6) If your equipment does not perform as required, refer to Section 3, MAINTENANCE INSTRUCTIONS. Report any malfunctions or failures on DA Form 404, or refer to DA Pam (7) The "Item No. column shall be used as a source of item numbers for the TM Number column on DA Form 404, Equipment Inspection and Maintenance Worksheet, in recording results of PMCS. Table. Operator/Crew Preventive Maintenance Checks and Services ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: Before Chassis, Semitrailer Refer to TM &P for PMCS procedures. Stated PMCS requirements are not met. Before Heaters Refer to applicable heater TM for PMCS procedures. Stated PMCS requirements are not met. 3 Before Air Conditioner Refer to applicable air conditioner TM for PMCS procedures. Stated PMCS requirements are not met. 4 Before Ground Rod and Wire Installation Check that ground rod (p. 3-) is properly installed and connected to trailer grounding terminal before connecting to facility power. Trailer chassis is not properly grounded before connecting van to facility power. - Change

14 TM &P Table -. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: 5 Before Utility Grinding Machine Check grinding wheels for cracks or breaks. If either grinding wheel is cracked or broken notify organizational maintenance to replace it before using utility grinding machine. Either grinding wheel is cracked or broken. 6 During Battery Char ger Note whether or not battery charger (p. 3-5) is fully operable. Battery charger is not operating as designed or is operating intermittently. 7 During Utility Grinding Machine Check utility grinding machine (p. 3-7) for normal operation and listen for unusual noise or vibration. Utility grinding machine is inoperative or makes unusual noise or vibration. 8 During Test Equipment Frequency Converter (p. 3-7), Sweep Oscillator (p. 3 7), Oscilloscope (p. 3-), DC Power Supply (p. 3 ), Spectrum Analyzer (p. 3 7), Semiconductor Test Set (p. 3-8), Voltmeters (pp and 3 3), Power Meter (p. 3-34), Digital Multimeter (p. 3-35), Multimeters (pp and 3-40). Note whether or not each of the above items of test equipment is fully operable. Test equipment items are not operating as designed or are operating intermittently. Change -3

15 TM &P Table. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: 9 During Vacuum Cleaner Note whether or not vacuum cleaner (p. 3-37) has normal amount of suction, and listen for unusual noise or vibration. Vacuum cleaner is inoperative, has inadequate suction, or if the vacuum cleaner is producing unusual noise or vibration during oper ation. 0 After Shop Van and Equipment Report any needed repairs or inoperative equipment to organizational maintenance. Needed repairs or problems are not reported to orga nizational maintenance. WARNING Ensure that trailer chassis is grounded before connecting to facility power. Failure to do so could cause death or injury to personnel. Quarterly AC Electrical System Overhead Lights. Check operation of all overhead fluorescent lights. Replace any burned out or flickering tubes and/ or defective starters. Any fluorescent tubes are inoperative or flickering or if any starters are defective. Distribution Panel and Circuit Breakers. Check that distribution panel (p. 3-4) is intact and that all. circuit breakers show proper on/off operation. Tighten any loose mounting hardware. Notify organizational maintenance of any defective circuit breakers. Any circuit breakers are broken, hard to operate, will not stay on, or cut off when there is no short/overload. -4 Change

16 TM &P Table. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: AC Electrical System (Cent) Blackout Light. Check operation of blackout light and blackout mode switch. Replace bulb if burned out. Notify organizational maintenance if mode switch is defective. Blackout light is burned out or inoperative, if there is no spare blackout light bulb on board the shop van, or if shop lights will not go off when rear door is opened during blackout mode. Emergency Light. Check operation of emergency light. Replace bulb if burned out. Notify organizational maintenance if emergency light is inoperative. Emergency light is burned out or inoperative, or if there is no spare emergency light bulb on board the shop van. Switches and Service Receptacles.. Check all service receptacles with an outlet tester to see that they are live and properly wired. Check that switches and service receptacles are not cracked or broken. Tighten any loose switches or receptacles and their cover plates. Report any defective switches or receptacles or missing mounting hardware to organizational maintenance. Switches or service receptacles are cracked or broken; if any service receptacles are dead, intermittent, or improperly wired or grounded; if switches or service receptacles and their cover plates are loose; or if hardware is missing. Change -5

17 TM &P Table. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: Quarterly Fire Extinguishers Check that fire extinguisher (p. 3 ) seals are not broken, that gage reads within the normal range, and that the fire extinguisher is not corroded or leaking Tighten any loose mounting hardware on fire extinguisher bracket. Notify organizational maintenance to replace fire extinguisher if gage reads below normal or if there is corrosion or evidence of leakage. Fire extinguishers are missing, if seals are broken, if gage does not read within normal range, if fire extinguishers are corroded or show evidence of leakage, or if mounting bracket is loose. 3 Quarterly First Aid Kit Check that first aid kit (p. 3-) is intact and contains the proper kind and amount of supplies. Tighten any loose mounting hardware and replace any missing or deteriorated supplies. First aid kit is loose or missing or if supplies are missing or deteriorated. 4 Quarterly Stools and Retaining Straps Check that stools (p. 3-3) are securely held by the retaining straps. Remove stools and check them for loose or missing hardware. Tighten hardware as necessary. Check strap mounting brackets for loose or missing hardware. Tighten hardware as necessary. Notify organizational maintenance to replace retaining straps if broken or deteriorated and to replace any missing mounting hardware. Stool hardware is loose or missing such that stool is unsafe to sit on, or if retaining straps are cut or broken such that stools cannot be secured for travel. -6 Change

18 TM &P Table -. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: 5 Quarterly Small Parts Cabinet and Tool Box Check that small parts Cabinet (p. 3-3) and tool box (p. 3-33) are securely mounted and that small parts cabinet drawers operate freely. tighten any loose hardware. Notify organizational maintenance to replace any missing mounting hardware. Lubricate drawer sliding surfaces with grease as needed. Small parts cabinet is loose or if drawers do not open and close freely. 6 Quarterly Front Work bench Check that front workbench (p. 3 5) is se cure, that drawers operate freely, and that drawer stops function properly. Tighten any Loose hardware, and notify organizational maintenance to replace any missing hardware. Lubricate drawer slides with grease as needed. Workbench is not securely mounted; if drawers are stuck, binding, or have broken stops; or if hardware is loose or missing. 7 Quarterly Machinist Vise Check that machinist vise (P. 3 7) is securely mounted to workbench and operates freely. tighten mounting hardware as needed. Notify organizational maintenance of any missing hardware. Clean machinist vise with a solventdampened cloth as needdrive ed. Lubricate screw and sliding surwith Faces of vise grease as needed. Machinist vise is loose or does not operate freely. NOTE It is convenient to perform PMCS items 8 and 9 concurrently. Change -7

19 TM &P Table. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: 8 Quarterly Left and Right Side Workbench Check that workbenches (p. 3-) are securely mounted, that drawers operate freely, that drawer stops are functional, and that all mounting hardware is present and secure. Lubricate drawer slides with grease as needed. Tighten any loose hardware and notify organizational maintenance to replace any missing hardware. Notify organizational maintenance if any drawer is inoperative. Workbench mountings are loose, if any drawers are stuck or difficult to open/ close, have inoperative stops, or loose or missing hardware. 9 Quarterly Common Tool and Components Inventory. Check drawers (p. 3 3) which contain the common tools and components authorized for the shop. Estimate the actual percentage of common tools and components versus the authorized quantity. Replenish any missing common tools or any components that are exhausted or in short supply. The estimated total amount of common tools and components pres ent is less than 90 percent of that authorized for the shop. 0 Quarterly Frequency Converter and Sweep Oscillator Unfasten frequency converter and sweep oscillator storage case (p. 3-7) retaining straps. Inspect cases for breaks and cracks. Notify organizational maintenance to replace case if it contains breaks or cracks such that the frequency converter or sweep oscillator are not adequately protected from dust, Frequency convertor and/or sweep -8 Change

20 TM &P Table -. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: Frequency Converter and Sweep Oscillator (Cont) humidity, etc. Inspect retaining straps for cuts or breaks. Notify organizational maintenance to replace broken or defective retaining straps. Wipe off case with clean cloth dampened with water. Remove frequency converter and sweep oscillator from case and wipe off with clean cloth dampened with water. Check that all accessories supplied with the frequency converter and sweep oscillator are present. Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibration label has expired. be secured for movement; if any supplied accessories are missing; or if calibration Label(s) is expired. Quarterly Oscilloscope Unfasten oscilloscope storage case (p. 3-) retaining straps. Inspect case for breaks and cracks. Notify organizational maintenance to replace case if it contains breaks or cracks such that the oscilloscope is not adequately protected from damage due to dust, humidity, etc. Inspect re - taining straps for cuts or breaks. Notify organizational maintenance to replace any defective retaining straps. Wipe off case with clean cloth dampened with water. Remove oscilloscope from storage case and wipe off with clean Oscilloscope storage case is cracked or broken such that the equipment is not protected from infiltration of dust, humidity, etc; if retaining straps are cut or broken such that equipment cannot be secured for movement; if any supplied accessories are missing; or if calibration label is expired. Change -9

21 TM &P Table -. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: Oscilloscope (Cont) cloth dampened with water. Check that all accessories supplied with the oscilloscope are present. Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibra tion label has expired. Quarterly DC Power Supply Check that DC power supply (p. 3 ) is securely fastened. Tighten any loose control knobs or hardware. Notify organizational maintenance to replace any missing knobs or hardware. Wipe off DC power supply case with a clean cloth dampened with water. Remove any corrosion from painted surfaces with sandpaper and spot paint (see TM ) as required. DC power supply control knobs or hardware is loose or missing. 3 Quarterly Spectrum Analyzer Wipe off spectrum analyzer (p. 3-7) case with a. clean cloth dampened with water. Check that all accessories supplied with the spectrum analyzer are present. Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibration label has expired. Any supplied accessories are missing, or if calibration label has expired. -0 Change

22 TM &P Table. Operator/Crew Preventive Maintenance Checks and Services (Cont) ITEM NO. INTERVAL LOCATION ITEM TO CHECK/SERVICE PROCEDURE NOT FULLY MISSION CAPABLE IF: 4 Quarterly Semiconductor Test Set Wipe off semiconductor test set (p. 3-8) case with a clean cloth dampened with water. Check that all accessories supplied with the semiconductor test set are present. Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibration label has expired. Open battery compartment and check for leakage or corrosion. Clean any corrosion from battery compartment contacts. Test batteries and replace with fresh ones if they are leaking or spent. Any supplied accessories are missing, if calibration label has expired, or if batteries are leaking or spent. 5 Quarterly Voltmeters Wipe off voltmeter (pp and 3-3) cases with a clean cloth dampened with water. Check that all accessories supplied with the voltmeters are present. Notify organizational maintenance to replace any missing accessories. Check calibration labels, and notify organizational maintenance if calibration label(s) has expired. Open battery compartment and check for battery leakage or corrosion. Clean any corrosion from battery compartment contacts. Test batteries and replace with fresh ones if they are leaking or spent. Any supplied accessories are missing, if calibration label has expired, or if batteries are leaking or spent. Change -

23 TM &P Table -. ITEM NO INTERVAL Quarterly Quarterly Quarterly Operator/Crew Preventive Maintenance Checks and Services (Cont) LOCATION ITEM TO CHECK/SERVICE Power Meter Digital Mul timeter Multimeters PROCEDURE Wipe off power meter (p. 3 34) case with a clean cloth dampened with water. Check that all accessories supplied with power meter are present. Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibration label has expired. Wipe off digital multimeter (p. 3 35) case with a clean cloth dampened with water. Check that all accessories supplied with the digital multimeter are present, Notify organizational maintenance to replace any missing accessories. Check calibration label, and notify organizational maintenance if calibration label has expired. Wipe off multimeters (PP and 3-40) with a clean cloth dampened with water. Check that all accessories supplied with the multimeters are present. Notify organizational maintenance to replace any missing accessories. Check calibration labels, and notify organizational maintenance if calibration label(s) have expired. Open battery compartment and check for leakage or corrosion. Clean any corrosion from battery compartment contacts. Test batteries and replace with fresh cries if they are leaking or spent. NOT FULLY MISSION CAPABLE IF: Any supplied accessories are missing, or if calibration label has expired. Any supplied accessories are missing or if calibration label has expired. Any supplied accessories are missing, if calibration label is expired, or if batteries are leaking or spent. Change U.S. GOVERNMENT PRINTING OFFICE: /70074 PIN:

24 Section 3. MAINTENANCE INSTRUCTIONS TM &P 3-. Reference Instructions. Refer to TM &P for instructions pertaining to service upon receipt of equipment, movement to a new worksite, repair parts (special tools and equipment) and lubrication instructions for the shop sets. Refer to appendix A for instructions manuals. 3-. Repair Parts. The following paragraphs/procedures refer to figures located in Section 4, Repair Parts List, page Fire Extinguisher and Bracket. a. General. The fire extinguishers are mounted on the wall at the front and rear of the van. b. Removal (fig and 3). () Release the latch and remove the fire extinguisher. () Remove mounting hardware and bracket. c. Installation. Install the fire extinguisher and bracket in reverse order of removal, b above First Aid Kit. a. General. The first aid kit is mounted on the wall in back of the left side workbench. b. Removal (fig ). Release latch and remove the first aid kit. c. Installation. Install kit in the reverse order of removal, b above Data Plates. The data plates are located on the rear door and wall. a. Removal. Refer to figure and remove data plates. b. Cleaning, Inspection and Repair. WARNING Dangerous chemical solvents are used with this equipment. Avoid prolonged breathing of vapors; insure that there is adequate ventilation at all times. Avoid skin contact. Wash hands immediately after contact with solvent. If solvent gets into your eyes, flush your eyes immediately with clean water. Seek medical attention if necessary. () Clean data plates with cleaning solvent (P-D-680) and dry thoroughly. 3-

25 TM &P () Inspect for dents and other damage. (3) Replace damaged data plates. c. Installation. Refer to figure and install data plates. Figure. Rear wall mounted equipment. ITEM NAME QTY PART NUMBER FSCM Plate, Wiring 37E87 Plate, B.O. Warning 37E833 Rivet 6 MIL-R-443/6 Bracket 37E86 Screw 4 MS Plate, EMI 37E8303 Fire Extinguisher Bracket Screw 4 MS

26 TM &P 3-6. Stools. a. General. Two stools are located under the front workbench and two stools are located on top of the front workbench. b. Removal (fig 3). Unfasten four straps (6) and remove stools. c. Installation. Install in reverse order of removal, b above Clock. a. General. The clock is located on the front wall above the front workbench. b. Removal (fig 3). Remove clock from mounting bracket. Remove two screws (5) and the bracket (7). c. Installation. Install in reverse order of removal, b above Small Parts Cabinet. a. General. The small parts cabinet is located under the front workbench in back of the stools. b. Removal (fig 3). () Remove two stools under the front workbench (para 3-6). () Remove the ten (0) rubber electrical insulation mats. (3) Remove strap (3), two each screws (0), washers (), and nuts (). (4) Remove four screws (5) and two loops (4). (5) Remove the cabinet. c. Installation. Install the small parts cabinet in reverse order of removal, b above Tool Box Appendix A. a. General. Tool box A is located on the roadside of the front workbench. b. Removal (fig 3). () Remove tool box A by loosening strap (3). () Remove strap (6), four screws (5), and two loops (4). c. Installation. Install in reverse order of removal, b above. 3-3

27 TM &P Figure 3. Front wall mounted equipment. ITEM NAME QTY PART NUMBER FSCM Workbench Nut, Blind, Rivet Screw Washer Screw Fire Extinguisher Bracket Screw Cabinet, Small Parts Screw Washer Nut Strap Loop, Strap Screw Strap Bracket 0 37E88 MS 730-S56 MS MS MS MS E8 MS MS MS MS MS

28 TM &P 3-0. Front Workbench. a. General. The front workbench is located in front of the two center workbenches. b. Removal (fig 3). () Remove four (4) stools (para 3-6) and one small parts stowage cabinet (para 3-8), tool box A (para 3-9), clock (para 3-7), and fire extinguisher (para 3-3). () Remove the ten (0 ea) rubber electrical insulation sheets. (3) Disconnect electrical receptacle and conduit from workbench (para 3-9). (4). (4) Refer to figure 3 and remove six screws (3) and six washers (5) Remove eight screws (5) and remove workbench. c. Cleaning, Inspection and Repair. WARNING Dangerous chemical solvents are used with this equipment. Avoid prolonged breathing of vapors; insure that there is adequate ventilation at all times. Avoid skin contact. Wash hands immediately after contact with solvent. If solvent gets into your eyes, flush your eyes immediately with clean water. Seek medical attention if necessary. () Clean all metal parts with cleaning solvent (P-D-680) and dry thoroughly. Clean other parts with a clean dry cloth. () Inspect for dents, nicks and burrs, cracks, breaks and other damage. (3) Remove distortions or replace damaged items. Replace missing hardware. d. Installation. Install the front workbench in the reverse order of removal, b above. 3-. Battery Charger. a. General. The charger is located at the rear of the right side workbench on the floor (see fig 4). 3-5

29 TM &P Figure 4. Battery charger and machinist s vise. ITEM NAME QTY PART NUMBER FSCM Screw Washer Washer Nut Strap Loop Screw Bracket Bracket MS MS MS MS MS MS E800-37E

30 TM &P b. Removal. Refer to figure 4 and unfasten straps and remove battery charger. c. Installation. Refer to figure 4 and install battery charger and secure straps. 3-. Machinist Vise. a. General. The vise is located on top of the right side workbench above the battery charger. b. Removal (fig 4). () Remove drawer number 3. () Remove four nuts (4), four flatwashers (), four lockwashers (3) and four screws (l). (3) Remove vise. c. Installation. Install in reverse order of b above Utility Grinding Machine. a. General. The grinding machine is located on the front of the right side workbench. b. Removal. () Remove drawer number. WARNING Dangerous voltages, capable of causing death are present in this vehicle, and the equipment provided in its tool load. Use extreme caution when handling, testing, or adjusting any electrical equipment. () Disconnect electrical power at circuit breaker #4 in power panel (para 3-9). (3) Remove two nuts (l), two lockwashers (), two flatwashers (3), and two screws (4) (fig 5). (4) Disconnect electrical connections to grinder (para 3-9). (5) Remove grinding machine (fig 5). c. Installation. Install in reverse order of removal, b above Frequency Convertor and Sweep Oscillator Electronic Cases. a. General. The electronic cases are located on top of the left side workbench. 3-7

31 TM &P Figure 5. Disconnecting and removing utility grinding machine. ITEM N AME QTY PART NUMBER FSCM Nut Washer, Lock MS Washer, Flat MS Screw MS 783- MS

32 TM &P Side View Top View ITEM Figure 6. NAME Nut Washer, Lock Screw Loop, Strap Strap Screw Nut Washer, Flat Base Strap Strap Screw Screw Nut Washer, Lock Washer, Flat Screw Washer, Lock Washer, Flat Rivnut Electronic cases and power supply mounting. QTY PART NUMBER FSCM MS MS MS MS O MS MS MS E MS MS MS MS MS MS MS MS MS

33 TM &P Figure 7. Ground rod and upright broom. ITEM NAME Qty PART NUMBER FSCM Bracket Bracket Screws 4 Clip MS

34 TM &P b. Removal (fig 6). () Unfasten four straps (5) and remove the electronic cases. () Remove sixteen each screws (6), nuts (7), washers (s), and mounting bases (9). c. Installation. Install in reverse order of removal, b above Oscilloscope Electronic Case. a. General. The electronic case is located forward of the right side workbench on the floor. b. Removal (fig 6). Unfasten two straps (0) and one strap () and remove electronic case. c. Installation. Install in reverse order of removal, b above DC Power Supply. a. General. The DC power supply is located forward of the left side workbench on the floor. b. Removal (fig 6). WARNING Dangerous voltages, capable of causing death are present in this vehicle, and the equipment provided in its tool load. Use extreme caution when handling, testing, or adjusting any electrical equipment. () Shut-off power to the DC power supply in the circuit breaker panel on the left rear interior wall (see fig 9). () Remove four each screws (3), nuts (4), lockwasher (5), flat washers (6), screws (7), lockwasher (8), and flat washers (9). (3) Slide power supply forward and remove rear access panel (see fig 4). (4) Disconnect electrical connections and conduit, and remove power supply (para 3-9). c. Installation. Install in reverse order of removal, b above Ground Rod and Upright Broom. a. General. The ground rod is mounted on the forward inner rail of the right side workbench, and the broom on the left. 3-

35 TM &P b. Removal (fig 7). () Remove ground rods and broom by lifting out of brackets. () Remove brackets by removing six screws (3). c. Installation. Install in the reverse order of removal, b above Left and Right Side Workbench. a. General. The two workbenches are located in the center of the trailer and are mounted to the van floor. b. Removal (fig 8). () Remove battery charger (para 3-). () Remove machinist vise (para 3-). (3) Remove utility grinding machine (para 3-3). (4) Remove frequency convertor electronic case (para 3-4). (5) Remove sweep oscillator electronic case (para 3-4). (6) Remove power supply (para 3-6). (7) Remove oscilloscope electronic case (para 3-5). (8) Remove upright broom and brackets (para 3-7). (9) Remove ground rod and brackets (para 3-7). (0) Remove all drawers from workbenches. () Disconnect electrical connections from both workbenches (para 3-9). () Remove 6 bolts and 6 washers (8 for each workbench) securing workbenches to van floor, and remove the two benches. c. Disassembly. Refer to figure 8 and disassemble the workbenches and related parts. d. Cleaning, Inspection and Repair. WARNING Dangerous chemical solvents are used with this equipment. Avoid prolonged breathing of vapors; insure that there is adequate ventilation at all times. Avoid skin contact. Wash hands immediately after contact with solvent. If solvent gets into your eyes, flush your eyes immediately with clean water. Seek medical attention if necessary. 3-

36 TM &P Figure 8. Left and right side workbench. ITEM NAME QTY PART NUMBER FSCM Drawer, Work Bench 4 Rivet, Spring Mounting Spring, Drawer Retainer Rivet, Handle Mounting 8 Handle, Grab Rivet, Holder Mounting 6 Holder, Label Screw, Bench Top Mounting 8 Top, Bench Cover, Conduit Mounting Cover, Receptacle 3 Receptacle, Electrical 3 Wire, 5 Long 3 Wire, Long 3 (used on right side) Screw, Work Bench Mounting 8 Washer, Work Bench Mounting 8 Nut, Work Bench Mounting 8 Frame, Bench (used on 37E806-8) Divider, Drawer 8 37E805 MS 063-4P5 37E835 MS E035 MS 063-P3 37E804 MS E E E E E806-7 MS MS MS 730-s E

37 TM &P () Clean all metal parts with cleaning solvent (P-D-680) and dry thoroughly. Clean other parts with a clean cloth. () Inspect items for cracks, breaks, bends, dents and other damage. (3) Check mounting hardware for damaged threads and distortion. Replace damaged and missing hardware. (4) Straighten bends and dents. Remove nicks, burrs and distortions. (5) Replace all items beyond repair. e. Assembly. Refer to figure 8 and reassemble the workbenches and related parts. f. Installation. Install the left and right side workbench in the reverse order of removal, b above Electrical Installation. a. General. Refer to TM &P for repair instructions. In addition, shop set componets not covered in above manual are covered below. b. Load Centers and Related Components. WARNING Dangerous voltages, capable of causing death. are present in this vehicle and the equipment provided in its tool load. Use extreme caution when handling, testing or adjusting any electrical component. NOTE Before removal and after installation test the wiring, paragraph ()(f) below. () Removal and Disassembly. Refer to figures 9 through 6 to disconnect, remove, and disassemble the electrical installation. () Cleaning, Inspection and Repair. (a) Clean electrical parts with a clean dry cloth. WARNING Dangerous chemical solvents are used with this equipment. Avoid prolonged breathing of vapors; insure that there is adequate ventilation at all times. Avoid skin contact. Wash hands immediately after contact with solvent. If solvent gets into your eyes, flush your eyes immediately with clean water. Seek medical attention if necessary. 3-4

38 TM &P (b) thoroughly. (c) necessary. Clean metal parts with cleaning solvent (P-D-680) and dry Inspect all parts of load centers for damage and replace as (d) Inspect the wiring covers and mounting brackets for dents, cracks, breaks, loose or missing hardware and other defects. (e) Tighten or replace loose or missing mounting hardware. Straighten minor bends. Replace damaged or defective mounting brackets, wiring covers, and flexible conduit. (f) Test the wire for continuity. Disconnect each end of the wire from the components to which it is attached as shown by the wiring diagram (fig FO-). Touch the test probes of a multimeter to each end of the wire. If the multimeter does not indicate continuity, replace the wire. WARNING Dangerous voltages, capable of causing death, are present in this vehicle and the equipment provided in its tool load. Use extreme caution when handling, testing, or adjusting any electrical component. NOTE The ceiling lights, bench grinder, and workbench receptacles are supplied with power by 0-volt, single-phase circuit. Wiring for each circuit in this system must be replaced individually. Refer to the wiring diagrams (fig FO-) when testing and replacing wiring in the individual circuits. c. Assembly and Installation. Refer to figures 9 through 5 to reassemble, install and reconnect electrical components. 3-5

39 TM &P Circuit Breaker Legend. Front Workbench Receptacle. Bench Receptacles, Streetside 3. Heater, Streetside 4. Bench Grinder 5. Heater, Curbside 6. Bench Receptacles, Curbside 7. Ceiling Receptacle 8. Power Supply 9. DC Power Supply Ceiling Receptacle Ceiling Receptacle Emergency Light Door Switch, Blackout Ceiling Receptacles Ceiling Receptacles Air Conditioning Main Figure 9. Distribution panel. ITEM NAME Circuit Breaker, Duplex 5-5A Circuit Breaker, 3 Pole, 0A Circuit Breaker Pole, 5A Circuit Breaker, Single, 5A Circuit Breaker, Duplex, 5-0A Connector, Snap-In QTY 3 3 PART NUMBER 37E84-37E E E84-37E FSCM

40 TM &P Figure 0. Rear crossover conduit. ITEM NAME QTY PART NUMBER FSCM Connector, Straight 38E0003- Conduit, Flexible 4.9 ft 37E Bushing, Anti-Short

41 TM &P Figure. Right side workbench and bench grinder conduit, ITEM NAME QTY PART NUMBER FSCM Wire Marker Wire Connector, 90 Elbow Bushing, Antishort Conduit, Flexible Strap, Retaining Screw Cover Plate 6 MS ft 4.8 ft MIL-W-5086/--9 38E E875-8 MS MS E

42 TM &P Figure. Left side workbench conduit. ITEM NAME QTY PART NUMBER FSCM Connector, 90 Elbow w/nut Bushing, Anti-Short Conduit, Flexible Screw Strap, Retaining Cover Plate Wire Wire Marker 4.8 ft 50 ft 8 38 E E875-8 MS MS E806-4 MIL-w-5086/--9 MS

43 TM &P Figure 3. Front workbench conduit. ITEM NAME Wire Wire Marker Connector, 90 Elbow Bushing, Anti-Short Conduit, Flexible Screw Strap, Retaining Cover Plate Receptacle Box, Junction QTY 0 ft 8 3 ft 5 5 PART NUMBER MIL-W-5086/--9 MS E E875-8 MS W-J E875-3 FSCM

44 TM &P Figure 4. DC power supply conduit. ITEM NAME QTY PART NUMBER Connector, 90 Elbow 38E Bushing, Anti-Short Conduit, Flexible 7. ft 37E875-8 Strap, Retaining MS Screw MS Wire Marker 4 MS Wire 0 ft MIL-W-5086/--9 FSCM

45 TM &P Figure 5. Ceiling outlet wiring. ITEM NAME QTY PART NUMBER Wire Marker 0 MS Wire 43.5 ft MIL-W-5086/--9 Box, Junction 37E875-3 Locknut Nipple, Chase 00-7 Receptacle W-C-596/85-l Cover 37E806-5 FSCM

46 TM &P 3-0. Tools and Equipment. Tools and equipment not previously listed which requires special installation of drawer loading is included in this section. Illustrations provided are as follows: Figure Description Inst., Frequency Convertor Inst., Sweep Oscillator Inst., Oscilloscope Inst., Drawer No. Inst., Drawer No. 3 Inst., Drawer No. 4 Inst., Drawer No. 5 Inst., Drawer No. 6 Inst., Drawer No. 7 Inst., Drawer No. 8 Inst., Drawer No. 9 Inst., Drawer No. Inst., Drawer No. 3 Inst., Drawer No. 5 Inst., Drawer No. 9 Inst., Drawer No. 3 Inst., Drawer No. 5 Inst., Drawer No. 7 NOTE All components shown on the following figures which are not listed in the legend are components of SC CL-B06. These items are listed in chapter

47 TM &P 760B0-000 Figure 6. Inst., Frequency converter. ITEM NAME Angle, Mounting Angle, Mounting Angle, Mounting Angle, Mounting Bracket, Mounting Bracket, Mounting Angle, Mounting Screw Washer, Flat Washer, Lock Screw (fasteners for equipment) Washer, Lock Screw Washer, Lock Nut Screw Power Cord Assembly Bracket Assembly Screw QTY PART NUMBER MS MS MS MS MS MS MS MS MS MS FSCM 3-4

48 TM &P 760B0-000 ITEM 3 4 5* * *Not Shown. NAME Figure - 7. Angle, Mounting Angle, Mounting Angle, Mounting Angle, Mounting Angle, Mounting Angle, Mounting Angle, Mounting Bracket Assembly Bracket Assembly Panel Assembly Panel Assembly Screw Washer, Flat Washer, Lock Screw Washer, Lock Screw Washer, Lock Nut Power Cord Assembly Screw Inst., Sweep oscillator. QTY PART NUMBER O MS MS MS MS MS MS MS MS MS FSCM 3-5

49 TM &P END COVER (CASE) (REF) 760B Figure 8. Inst., Oscilloscope ITEM NAME QTY PART NUMBER FSCM Pad, Foam Pad, Foam 3 Pad, Foam 4 Pad, Foam 5 Adhesive 4 4 AR MMM-A

50 TM &P FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE Figure 9. Inst., Drawer no. ITEM NAME Pad, Foam Pad, Foam 3 Divider 4 Adhesive QTY PART NUMBER E83 AR MMM-A-67 FSCM

51 TM &P AEL 59C SEMI-CONDUCTOR -PAPER, LENS TEST SET NOTE ACCESSORIES (REF) 970B0-00 FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRENE ADHESEIVE Figure 0. Inst., Drawer no. 3 ITEM NAME Pad, Foam Pad, Foam 3 Pad, Foam 4 Pad, Foam 5 Divider 6 Adhesive QTY PART NUMBER E83 AR MMM-A-67 FSCM

52 TM &P WRENCH, TORQUE WRENCH SET THREADING SET HEX WRENCH SET B0-00 ITEM NAME Wood Block Divider Figure. Inst., Drawer no. 4 QTY PART NUMBER FSCM E83 3-9

53 TM &P WOOD DIVIDER 4 FOAM PADS (REF) FOAM PADS FOAM PADS FOAM PAILS TOP & BOTTOM VOLT METER 400E FOAM TO BE EASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE ATTENUATOR 3750A B0-003 Figure. Inst., Drawer no. 5. ITEM NAME QTY PART NUMBER FSCM 3 4 Pad, Foam Pad, Foam Pad, Foam Pad, Foam 5 Divider 6 Adhesive E83 AR MMM-A

54 TM &P 970B0-004 Figure 3. Inst., Drawer no. 6. ITEM NAME Divider QTY PART NUMBER 3 37E83 FSCM 3-3

55 TM &P VOLT METER 40C NOTE FOAM TO EASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE B0-005 ITEM NAME Pad, Foam Pad, Foam 3 Divider 4 Adhesive Figure 4. Inst., Drawer no. 7. QTY PART NUMBER E83 AR MMM-A-67 FSCM

56 TM &P INST PORTABLE TOOL BOX 970B ACETONE CLEANING COMPOUND B0-007 Figure 5. Inst., Drawer no. 8. ITEM NAME QTY PART NUMBER Spacer, Wood Divider 37E83 FSCM 3-33

57 TM &P ACCESSORIES (REF) NOTE FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE (ITEM 5) POWER METER 435B Figure 6. Inst., Drawer no B0-008 ITEM NAME Pad, Foam 3 Pad, Foam Pad, Foam 4 Divider 5 Adhesive QTY PART NUMBER E83 AR MMM-A-67 FSCM

58 TM &P DIGITAL MULTI-METER 3465A NOTE FOAM TO BE EASTENED WITH CARBOLINE F- NEOPRINE ADHESIVE (ITEM 5) Figure 7. Inst., Drawer no.. 970B0-000 ITEM NAME QTY PART NUMBER FSCM Pad, Foam Pad, Foam 3 Pad, Foam 4 Divider 5 Adhesive E83 AR MMM-A

59 TM &P NOTE FOAM TO EASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE (ITEM 5) Figure 8. Inst., Drawer no B0-00 ITEM NAME QTY PART NUMBER FSCM Pad, Foam Pad, Foam Pad, Foam Divider Adhesive E83 AR MMM-A

60 TM &P PART NO. DESCRIPTION QTY VACUUM CLEANER BOTTOM PAD ADHESIVE B0-004 Figure 9. Inst., Drawer no. 5. ITEM NAME QTY PART NUMBER FSCM Pad, Foam Adhesive AR MMM-A

61 TM &P 6-TUBE RUBBER ADHESIVE VISE LUBRICANT VISE STRING, ROLL TUBE SILICONE COMPOUND 4-TUBE ADHESIVE 970B0-008 Figure 30. Inst., Drawer no. 9. ITEM NAME QTY PART NUMBER Divider 37E83 FSCM 3-38

62 TM &P PLATE DRILL MULTI-METER FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE (ITEM 5) 970B0-003 Figure 3. Inst., Drawer no. 3. ITEM NAME Pad, Foam Pad, Foam 3 Pad, Foam 4 Divider 5 Adhesive QTY PART NUMBER FSCM E83 AR MMM-A

63 TM &P MULTI-METER REFLECTOR FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRENE ADHESIVE (ITEM 6) 970B ITEM Figure 3. Inst., Drawer no. 5. NAME QTY PART NUMBER Pad, Foam Pad, Foam Pad, Foam Pad, Foam Divider Adhesive 4 AR E83 MMM-A-67 FSCM

64 TM &P Part No. Description Qty Location Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Adapter, Connector Binding Post Binding Post Clip Banana Plug Clip Clip Clip Plug Tip Battery Battery Attenuator Adapter FOAM TO BE FASTENED WITH CARBOLINE F- NEOPRINE ADHESIVE (ITEM 4) 970B Figure 33. Inst., Drawer no. 7. ITEM NAME Pad, Foam Pad, Foam 3 Divider 4 Adhesive QTY PART NUMBER E83 AR MMM-A-67 FSCM /(3-4 blank)

65 TM &P Section 4. COMPONENTS LIST, TOOLS AND EQUIPMENT 4-. Component Location, Table 4-. LEGEND CODE LOCATION PART NUMBERS EC EC EC TB TB PC DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR DR WM WM BM Installation, Frequency Convertor Installation, Sweep Oscillator Installation, Oscilloscope Installation, Tool Box, Appendix A Installation, Tool Box, Appendix B Installation, Small Parts Cabinet Installation, Drawer #l Installation, Drawer # Installation, Drawer #3 Installation, Drawer #4 Installation, Drawer #5 Installation, Drawer #6 Installation, Drawer #7 Installation, Drawer #8 Installation, Drawer #9 Installation, Drawer #0 Installation, Drawer # Installation, Drawer # Installation, Drawer #3 Installation, Drawer #4 Installation, Drawer #5 Installation, Drawer #6 Installation, Drawer #7 Installation, Drawer #8 Installation, Drawer #9 Installation, Drawer #0 Installation, Drawer # Installation, Drawer # Installation, Drawer #3 Installation, Drawer #4 Installation, Drawer #5 Installation, Drawer #6 Installation, Drawer #7 Installation, Drawer #8 Mounted Equipment, Rear Wall Mounted Equipment, Front Wall Mounted Equipment, Workbench 760B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B N/S N/S N/S 9 N/S N/S 7 N/S 8 N/S 9 N/S N/S N/S 30 N/S N/S N/S 3 N/S 3 N/S 33 N/S LOCATION LEGEND EC - Electronic Case DR - Drawer TB - Tool Box WM - Wall Mounted PC - Small Parts Cabinet BM - Workbench Mounted N/S - Not Shown on a Figure 4-

66 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST 4-. TOOLS AND EQUIPMENT LIST. THE TOOLS AND EQUIPMENT USED IN THE SHOP SET ARE LISTED IN TABLE 4- IN ALPHABETICAL SEQUENCE AND INCLUDE NATIONAL STOCK NUMBER (NSN), QUANTITY AND UNIT OF MESURE, LOCATION LEGEND, PART NUMBER, AND FEDERAL SUPPLY CODE FOR MANUFACTURES (FSCM) NUMBER. PART NSN DESCRIPTION QTY LOC * NUMBER FSCM ACETONE PT. DR 8 0-A ADAPTER, MIL-A 6 EA. DR 7 MIL-A / / ADAPTER, UG 349 B/U 4 EA. DR 7 UG 349 B/U ADAPTER, UG 64/U 4 EA. DR 7 UG 64/U ADAPTER, UG 5/U EA. DR 7 UG 55/U ADAPTER, MS EA. DR 7 MS ADAPTER, MIL-A- EA. DR 7 MIL-A / / ADAPTER, MIL-A- 4 EA. DR 7 MIL-A / / ADAPTER, MIL-A- EA. DR 7 MIL-A / / ADAPTER, MIL-A- 8 EA. DR 7 MIL-A / / ADAPTER, MIL-A- EA. DR 7 MIL-A /6 64/ ADHESIVE, CELLULOSIC 4 TU. DR 9 MMM-A NO NIIN ADHESIVE, RUBBER 6 TU. DR ADJUSTING TOOL, GYRO EA. TB 38E ALCHOHOL, ISOPROPYL CN. TB TT-I ALIGNMENT TOOL KIT EA. TB AMPLIFIER, PLUG-IN EA. EC 3 80A ANALYZER, SPECTRUM EA. DR 8557A ATTACHMENT, EXTENSION EA. TB GG-W ATTENUATOR, FIXED EA. DR 7 849B ATTENUATOR, VARIABLE EA. DR A BANANA PLUG 0 EA. DR BATTERY FILLER, EA. DR 3 W-B GRAVITY * LOCATION LEGEND BM - BENCH MOUNTED DR - DRAWER EC - ELECTRONIC CASE PC - PARTS CABINET TB - TOOL BOX WM - WALL MOUNTED 4-

67 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM BIT, SCREWDRIVER EA. TB GGG-B-00/ BIT, SCREWDRIVER EA. TB TMS 4-/ BLADE, HACKSAW 6 EA. TB GGG-B BOX, SMALL PARTS EA. TB BRIDGE, CAPACITANCE EA. EC 460A BROOM, UPRIGHT EA. BM H-B BRUSH, DUSTING EA. DR H-B BRUSH, FILE CLEANER EA. TB H-C BRUSH, VARNISH EA. TB H-B BRUSH, VARNISH EA. TB H-B BRUSH, WIRE, ROTARY EA. DR H-B BRUSH, WIRE EA. DR H-B CABLE ASSEMBLY, 6 FT. EA. DR 4 50A CABLE ASSEMBLY, EA. DR 0 PD 4A FT CABLE ASSEMBLY, 4 FT. 6 EA. DR A CABLE ASSEMBLY, 3 FT. EA. DR 4 BC NIIN CABLE ASSEMBLY, 3 FT. EA. DR 4 39-C CABLE ASSEMBLY, 6 FT. EA. DR 4 500A CABLE ASSEMBLY, 3 FT. 4 EA. DR 4 00A CABLE ASSEMBLY, EA. DR 4 38E EXTENDER CABLE, RADIO, RG 00 FT. DR MIL-C-7/ /CU CABLE, RADIO, RG 5 FT. DR MIL-C-7/ /U CARD HOLDER EA. TB SK CASE, ELECTRONIC EA. EC CASE, OSCILLOSCOPE EA. EC CHALK, MARKING GR. DR 4 SS-C CHAMOIS LEATHER EA. TB KK-C CHARGER, BATTERY EA. BM CHISEL, COLD EA. TB GG-C CLAMP, SCREW JACK EA. TB SK CLEANER VACUUM EA. DR 5 MIL-C CLEANING COMPOUND GL. DR 8 O-C CLIP, ELECTRICAL PG. DR 7 W-C-440/TC CLIP, ELECTRICAL 4 PG. DR 7 W-C-440/TCC CLIP, ELECTRICAL 4 EA. DR 7 W-C-440/TCI CLIP, ELECTRICAL 4 EA. DR 7 W-C-440/TCI CLIP, ELECTRICAL 0 EA. DR 7 W-C-440/PC CLIP, ELECTRICAL PG. DR 7 W-C-440/PC CLIP, ELECTRICAL PG. DR 7 34C CLOCK, WALL EA. WH GG-C CLOTH, ABRASIVE 3 SH. TB P-C CLOTH, CHEESECLOTH YD. TB CCC-C CONNECTOR, PLUG 6 EA. DR 0 W-C-596/

68 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM COUNTER, ELECTRONIC EA. EC 534A COUNTER, ELECTRONIC EA. EC 5345A DRESSER, ABRASIVE EA. DR GG-D WHEEL DRESSER, CONTACT DZ. TB GA POINT DOWN CONVERTER EA. EC 70B DRILL, ELECTRIC EA. DR 3 W-D DRILL SET SE. TB GG-D DRILL SET SE. TB GG-D EXTENSION, SOCKET EA. TB GG-W WRENCH EXTENSION, SOCKET EA. TB GG-W WRENCH EXTRACTOR, D. I. P. EA. TB PILER EXTRACTOR, ELECTRON EA. TB GGG-E TUBE FACE, HAMMER EA. TB GGG-H FACESHIELD, INDUST- EA. DR L-F RIAL FILE, HAND EA. TB GGG-F FILE, HAND EA. TB GGG-F FILE, HAND EA. TB GGG-F FILE, ROTARY EA. TB GGG-F FILE SET W/CASE SE. TB GGG-F FINGER, MECHANICAL EA. TB GGG-F FIRST AID KIT EA. WM FLASHLIGHT EA. TB W-L FLUX, SOLDERING 4 C. DR 6 O-F FOCUS SCOPE TOOL EA. TB FRAME, HAND, HACKSAW EA. TB GGG-F GAGE, WIRE EA. TB GG-G GENERATOR, SIGNAL EA. EC 8640B GENERATOR, SIGNAL EA. EC 860A GRINDING MACHINE EA. BM W-G HAMMER, HAND, EA. TB GG-H MACHINISTS HEATSINK, PLIERS EA. TB HOLDER, HAMMER, EA. TB GGG-H INSERT HOLDER, SCREWDRIVER EA. TB / BIT INDICATOR, DIGITAL EA. EC 8600A INSULATION SLEEVING 5 FT. DR MIL-I INSULATION SLEEVING 5 FT. DR MIL-I INSULATION SLEEVING FT. DR MIL-I

69 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM INTERCONNECT BREAK- EA. DR 7 38E OUT BOX KEY, DRILL CHUCK EA. DR 3 GGG-C KEY SET, SOCKET HEAD SE. DR 4 GGG-K KEY SET, SOCKET HEAD SE. TB GGG-K KEY SET, SOCKET HEAD SE. TB SC-D KEY SET, SOCKET HEAD SE. TB GGG-K KEY SET, SOCKET HEAD SE. TB GGG-K KNIFE, POCKET EA. TB GGG-K LEAD SET, TEST 4 EA. DR 4 00A LIGHT, EXTENSION EA. DR 0 W-L LUBRICATING OIL, CN. DR 9 W-L GENERAL PURPOSE MAGNIFIER, MONOCULAR EA. TB MAGNIFIER, FOLDING EA. TB METAL PLATE EA. DR 3 QQ-S MIRROR, INSPECTION EA. TB GG-M MULTIMETER EA. DR 3 AN/USM MULTIMETER EA. DR 3465A MULTIMETER EA. DR 7 40D NUT, PLAIN, HEX 75 EA. PC MS NO NUT, PLAIN, HEX 75 EA. PC MS NO NUT, PLAIN, HEX 75 EA. PC MS NO NUT, PLAIN, HEX 75 EA. PC MS NO NUT, PLAIN, HEX 75 EA. PC MS / OSCILLOSCOPE SUB- EA. EC 3 80C 8480 ASSEMBLY PARER, ABRASIVE 3 SH. TB P-P PAPER, LENS BK. DR 3 NNN-P PHOTOMETER, DIGITAL EA. DR 3 J6 W/J PIN, TEST, MINE 4 EA. DR 6 304E DETECTING PLIERS, DIAGONAL EA. TB GGG-P CUTTING PLIERS, DIAGONAL EA. TB GGG-P CUTTING PLIERS, DIAGONAL EA. TB GGG-P CUTTING PLIERS, INSERTION EA. TB TOOL PLIERS, LOG NOSE EA. TB LC PLIERS, RETAINING EA. TB RING 4-5

70 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM PLIERS, ROUND NOSE EA. TB GGG-P PLIERS, ROUND EA. TB GGG-P NEEDLE, CURVED PLIERS, ROUND EA. TB GGG-P NEEDLE, STRAIGHT PLIERS, SLIP JOINT EA. TB GGG-P PLIER TYPE HEATSINK EA. TB PLUG, TIP 0 EA. DR PLUG IN, TIME BASE EA. EC 3 8A POST, BINDING, BLACK EA. DR 7 0B POST, BINDING, RED EA. DR 7 0R POWER SUPPLY EA. BM PP4606G POWER SUPPLY EA. EC 668B PUNCH, CENTER EA. TB GGG-P PUNCH, DRIVE PIN, EA. TB GGG-P /8 DIA PUNCH, DRIVE PIN, EA. TB GGG-P /6 DIA PUNCH, DRIVE PIN, EA. TB GGG-P /4 DIA REAMER, HAND EA. TB GGG-R REFLECTOR ASSEMBLY EA. DR 5 330F ROD, GROUND EA. DR 0 W-R ROUGE, ABRASIVE LB. DR MIL-B B RUBBER SHEET,.5 IN. 4 SH. WM MIL-R RUBBER SHEET,.75 IN. 3 SH. WM MIL-R RUBBER SHEET, IN. 3 SH. WM MIL-R RULE, STEEL EA. TB GGG-R SCISSORS, ELEC- EA. TB GGG-S TRICIANS SCOPE, FINDER EA. DR SCREW, CAP, HEX 5 EA. PC MS /4-0, / SCREW, MACH, STEEL, 50 EA. PC MS FLAT, NO. -56, / SCREW, MACH, STEEL, 50 EA. PC MS FLAT, NO. -56, / SCREW, MACH, STEEL, 50 EA. PC MS FLAT, NO. 4-40, / SCREW, MACH, STEEL, 50 EA. PC MS FLAT, NO. 4-40, / SCREW, MACH, STEEL, 40 EA. PC MS FLAT, NO. 4-40, 3/ SCREW, MACH, STEEL, 5 EA. PC MS FLAT, NO. 6-3, / SCREW, MACH, STEEL, 5 EA. PC MS FLAT, NO. 6-3, 3/

71 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM SCREW, MACH, STEEL, 5 EA. PC MS FLAT, NO. 6-3, SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 6-3, / SCREW, MACH, STEEL, 5 EA. PC MS FLAT, NO. 6-3, / SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 6-3, SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 8-3, / SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 8-3, 3/ SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 8-3, SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 8-3, / SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 8-3, SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 0-4, 3/ SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 0-4, / SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 0-4, SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 0-4, / SCREW, MACH, STEEL, 0 EA. PC MS FLAT, NO. 0-4, SCREW, MACH, STEEL, 5 EA. PC MS FLAT, /4-0, / SCREW, MACH, STEEL, 5 EA. PC MS FLAT, /4-0, 3/ SCREW, MACH, STEEL, 5 EA. PC MS FLAT, /4-0, SCREW, MACH, STEEL, 5 EA. PC MS FLAT, /4-0, / SCREW, MACH, STEEL, 0 EA. PC MS 3590-, FLAT, /4-0, 3/ SCREW, MACH, STEEL, 0 EA. PC MS FLAT, /4-0, SCREW, MACH, STEEL, 0 EA. PC MS PAN, NO. -56, / SCREW, MACH, STEEL, 0 EA. PC MS PAN, NO. -56, / SCREW, MACH, STEEL, 0 EA. PC MS PAN, NO. 4-40, / SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 4-40, / 7 4-7

72 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 4-40, 3/ SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 6-3, / SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 6-3, / SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 6-3, 3/ SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 6-3, SCREW, MACH, STEEL, 0 EA. PC MS PAN, NO. 6-3, / SCREW, MACH, STEEL, 0 EA. PC MS PAN, NO. 6-3, SCREW, MACH, STEEL, 5 EA. PC MS PAN, NO. 8-3, / SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 8-3, 3/ SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 8-3, SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 8-3, / SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 8-3, SCREW, MACH, STEEL 8 EA. PC MS PAN, NO. 0-4, / SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 0-4, 3/ SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 0-4, SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 0-4, / SCREW, MACH, STEEL, 8 EA. PC MS PAN, NO. 0-4, SCREW, MACH, STEEL, 5 EA. PC MS PAN, /4-0, / SCREW, MACH, STEEL, 5 EA. PC MS PAN, /4-0, 3/ SCREW, MACH, STEEL, 5 EA. PC MS PAN, /4-0, SCREW, MACH, STEEL 5 EA. PC MS PAN, /4-0, / SCREW, MACH, STEEL, 0 EA. PC MS PAN, /4-0, SCREW, MACH, STEEL, 0 EA. PC MS PAN, /4-0, / SCREW STARTER, HAND EA. TB SN SCREWDRIVER, CROSS- EA. TB TMP TIP, NO

73 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM SCREWDRIVER, CROSS- EA. TB GGG-S TIP, NO., 3 IN SCREWDRIVER, CROSS- EA. TB GGG-S TIP, NO., / IN SCREWDRIVER, CROSS- EA. TB GGG-S TIP, NO., 4 IN SCREWDRIVER, CROSS- EA. TB GGG-S TIP, NO. 0, 4 IN SCREWDRIVER, DOUBLE EA. TB GGG-S OFFSET, 3 IN SCREWDRIVER, DOUBLE EA. TB GGG-S OFFSET, 5 IN SCREWDRIVER, FLAT, EA. TB GGG-S /4 IN. W, / IN SCREWDRIVER, FLAT EA. TB GGG-S /64 IN. W, 8 IN SCREWDRIVER, FLAT, EA. TB GGG-S /6 IN. W, 5 IN SCREWDRIVER, FLAT EA. TB GGG-S /6 IN. W, 6 IN SCREWDRIVER, FLAT EA. TB GGG-S /8 IN. W, IN SCREWDRIVER, FLAT, EA. TB GGG-S /4 IN. W, 4 IN SCREWDRIVER, FLAT, EA. TB GGG-S /6 IN. W, 8 IN SCREWDRIVER, OFFSET, EA. TB GGG-S CROSSTIP SCREWDRIVER, OFFSET, EA. TB GGG-S FLAT SCREWDRIVER SET, SE. TB GGG-S JEWELERS SCRIBER,MACHINISTS EA. TB GGG-S SETTING TOOL, GEAR EA. TB 38E SHEARS, METAL, HAND EA. TB GGG-S SILICONE COMPOUND TU. DR 9 MIL-S SILICONE, COMPOUND, TU. TB DC OZ SOLDER, LEAD ALLOY 0 LB. DR 6 QQ-S SOLDER, LEAD-TIN SL. TB GQ-S ALLOY,.03 DIA SOLDER, LEAD-TIN SL. TB QQ-S ALLOY, 0.63 DIA SOLDERING AID, 8 IN. EA. TB SOLDERING GUN, EA. TB GT HOUSING SOLDERING GUN, POWER- EA. TB 7A HEAD 3/6 IN. 4-9

74 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM SOLDERING GUN, POWER- EA. TB 6B HEAD /8 IN SOLDERING AND SE. DR 6 W-TCP-K RESOLDERING SET STONE, SHARPENING EA. TB SS-S STOOL, REVOLVING 4 EA. WM AA-S STRIPPER, WIRE EA. TB GGG-S TAPE, INSULATION, RL. TB MIL-I IN TAPE, INSULATION, RL. TB MIL-I IN TAPE, MEASURING, EA. TB GGG-T FT TAPE, LACING, NYLON SL. TB MIL-T YD TAPE, SOLDER REMOVAL, EA. TB FT TEST SET, RADIO EA. DR 9 435B 8480 FREQUENCY POWER TEST SET, SEMICON- EA. DR 3 59C DUCTOR TESTER, BATTERY EA. DR 3 GG-T-58A 8348 ELECTROLYTE THREADING SET, SCREW SE. DR 4 GGG-T-330B TOOL BOX, PORTABLE EA. TB GGG-T TOOL BOX, PORTABLE EA. TB GGG-T-558/ 8348 A TOOL KIT, ALIGNMENT EA. WM TRAY, SHOP MAINTE- EA. DR TRAY SHOP 3796 NANCE MAINTENANCE TWEEZER'S CRAFTSMAN EA. TB GGG-T TWEEZER'S CRAFTSMAN EA. TB GGG-T TWINE, LINEN LB. DR 9 MIL-T VISE, BENCH, IN. EA. DR 9 GGG-V VISE, MACHINIST'S, EA. BM GGG-V IN VISE, MACHINIST'S EA. DR 9 PN 05.5 IN VISE, WORK POSITION- EA. TB SK ING VOLTMETER, ELECTRONIC EA. DR 5 400E WASHER, FLAT, BRASS, LB. PC FF-W / WASHER, FLAT, STEEL, 3 HD. PC MS 783- NO WASHER, FLAT, STEEL, 3 HD. PC MS NO WASHER, FLAT, STEEL, HD. PC MS NO

75 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM WASHER, FLAT, STEEL, 3 HD. PC MS NO WASHER, FLAT, 75 HD. PC MS STEEL, NO WASHER, FLAT, STEEL, 3 HD. PC MS NO WASHER, FLAT, STEEL, 3 HD. PC MS / WASHER, FLAT, STEEL, 3 HD. PC MS / WASHER, FLAT, STEEL, 3 HD. PC MS / WASHER, LOCK, STEEL, 0 HD. PC MS NO WASHER, LOCK, STEEL, HD. PC MS NO WASHER, LOCK, STEEL, 7 HD. PC MS NO WASHER, LOCK, 00 EA. PC MS STEEL, 5/ WASHER, LOCK, 45 EA. PC MS STEEL, / WASHER, LOCK, 40 EA. PC MS STEEL, 3/ WASHER, LOCK, STEEL, HD. PC MS NO WASHER, LOCK, STEEL, HD. PC MS NO WASHER, LOCK, STEEL, HD. PC MS NO WASHER, LOCK, STEEL, HD. PC MS NO WASHER, LOCK, STEEL, HD. PC MS 03 NO WIRE, ELEC, BARE, LB. DR QQ-W AWG WIRE, ELEC, HOOK- 00 FT. DR MIL-W-76B 8349 UP, 8 AWG WIRE, ELEC, HOOK- 00 FT. DR MIL-W-76B 8349 UP, 8 AWG WIRE, ELEC, HOOK- 00 FT. DR MIL-W-76B 8349 UP, 8 AWG WIRE, ELEC, INSTRU- 00 FT. DR MIL-W MENT, 8 AWG WIRE, ELEC, INSTRU- 00 FT. DR MENT, 8 AWG WRENCH, ADJ., 0 IN. EA. TB GGG-W WRENCH, ADJ., 6 IN. EA. TB GGG-W

76 TM &P TABLE 4-. TOOLS AND EQUIPMENT LIST (CONT'D) PART NSN DESCRIPTION QTY LOC * NUMBER FSCM WRENCH SET, COMB. SE. DR 4 GGG-W WRENCH SET, COMB. SE. TB GGG-W WRENCH SET, SOCKET SE. TB PS WRENCH SET, SOCKET SE. TB GGG-W WRENCH SET, SPANNER SE. TB SC-B WRENCH, SPANNER EA. TB WRENCH, TORQUE EA. TB GGG-W WRENCH, TORQUE EA. DR 4 TQS-6-FU

77 TM &P APPENDIX A - REFERENCES A-. MAINTENANCE TM &P Operator s Organizational, Direct Support and General Support Maintenance Manual (Including Repair Parts and Special Tools List) for Semi-trailer, van, Shop) Folding Side, 6 Ton, 4-Wheel w/air Conditioning, M447C. A-. SHIPMENT AND LIMITED STORAGE TM Administrative Storage of Equipment. A-3. DESTRUCTION OF EQUIPMENT TM Procedures for Destruction of Equipment to Prevent Enemy Use. A-4. SUPPLY PUBLICATIONS SC CL-B06 Sets, Kits, Outfits Components List Shop Equipment, Electronic Repair Semi-trailer Mounted. A-5. PREVENTIVE MAINTENANCE DA PAM The Army Equipment Record System and Procedures. A- (A- blank)

78 By Order of the Secretary of the Army: JOHN A. WICKHAM, JR. General, United States Army Chief of Staff Official: ROBERT M. JOYCE Major General, United States Army The Adjutant General DISTRIBUTION : To be distributed in accordance with DA Form - requirements for FSC/FSG Group 4940.

79

80

81

82

83

84 TM &P FO-/(FO- BLANK)

85

86

87 THE METRIC SYSTEM AND EQUIVALENTS LINEAR MEASURE SQUARE MEASURE Centimeter = 0 Millimeters = 0.0 Meters = Inches Sq Centimeter = 00 Sq Millimeters = 0.55 Sq Inches Meter= 00 Centimeters = 000 Millimeters = Inches Sq Meter = 0,000 Sq Centimeters = 0.76 Sq Feet Kilometer = 000 Meters = 0.6 Miles Sq Kilometer =,000,000 Sq Meters = Sq Miles WEIGHTS CUBIC MEASURE Gram = 0.03 Kiloqrams = 000 Milligrams = Ounces CU Centimeter = 000 Cu Millimeters = 0.06 Cu Inches Kilogram = 000 Grams =. Lb C. Meter =,000,000 Cu Centimeters = 35.3 Cu Feet Metric Ton = 000 Kilograms = Megagram =. Short Tons TEMPERATURE LIQUID MEASURE 5/9 ( F - 3) = C Milliliter = 0.00 Liters = Fluid Ounces Fahrenheit is equivalent to 00 Celssius Liter = 000 Milliliters = 33.8 Fluid Ounces 90 Fahrenheit is equivalent to 3. Celsius 3 Fahrenheit is equivalent to 0 Celsius 9/5C + 3 = F TO CHANGE Inches.... Feet..... Yards.... Miles.... Square Inches Square Feet. Square Yards. Square Miles. Acres.... Cubic Feet.. Cubic Yards. Fluid Ounces. Pints Quarts.... Gallons... Ounces.... Pounds.... Short Tons.. Pound-Feet.... Pounds per Square Miles per Gallon. Miles per Hour.. APPROXIMATE CONVERSION FACTORS Inch TO MULTIPLY BY Centimeters Meters O5 Meters l4 Kilometers Square Centimeters Square Meters Square Meters Square Kilometers Square Hectometers Cubic Meters Cubic Meters Milliliters Liters, Liters, Liters, Grams Kilograms Metric Tons Newton-Meters Kilopascals Kilometers per Liter Kilometers per Hour TO CHANGE Centimeters Meters Meters Kilometers Square Centimeter.... Square Meters Square Meters Square Kilometers.... Square Hectometers.... Cubic Meters Cubic Meters Milliliters Liters Liters Liters Grams Kilograms Metric Tons Newton-Meters Kilopascals Kilometers per Liter... Kilometers per Hour... TO Inches Feet Yards Miles, Square Inches... Square Feet.... Square Yards... Square Miles... Acres Cubic Feet.... Cubic Yards.... Fluid Ounces... Pints Quarts Gallons Ounces Pounds Short Tons.... Pound-Feet.... Pounds per Square Miles per Gallon. Miles per Hour.. MULTIPLY BY Inch TA08999

88 TM &P, SHOP EQUIPMENT, ELECTRICAL REPAIR, SEMI-TRAILER MOUNTED (NSN )

89 This fine document... Was brought to you by me: Liberated Manuals -- free army and government manuals Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap watermarks and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends? I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on. I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines: <A HREF= Military and Government Manuals</A> Sincerely Igor Chudov Chicago Machinery Movers