Karbon Kitchen Sink Tap

Transcription

1 K-6227A Karbon Kitchen Sink Tap Installation and User Guide INSTALLER: IMPORTANT This product manual is the property of the customer and must be retained with the product for maintenance and operational purposes. 1

2 important information Tap Due to the non-standard diameter of the remote valve (51 mm), the remote valve cannot be installed through a standard 35 mm tap hole in a sink. Choose a sink without tap holes then install the tap and remote valve through the countertop. Refer to the countertop manufacturer for drilling of the holes. 1. Make sure that you follow all the local plumbing and building regulations in operation. 2. For new installations, install the tap in the sink before installing Remote Valve the sink. 3. Before installation, unpack the tap and inspect for damage. specification Plumbing Connections G ½ Supply fitting connections Hot (H) and Cold (C) inlets must be connected to the correct inlet supplies. ASME A / CSA B : Rated Pressure (section 4.1.1) - Fittings shall be designed to function at water working pressures between 140 and 860 kpa (20 and 125 psi). Rated Temperature (section 4.1.2) - Fittings shall be designed for rated supply temperatures between 5 to 71 C (40 to 160 F). Burst Pressure (section 5.3.2) - Fittings shall withstand a hydrostatic burst pressure of 3450 kpa (500 psi) for 1 minute without distortion or failure of the pressure envelope 2

3 Installation Ø 51 mm Valve Hole 1. Locate the remote valve within 203 mm of the spout. Refer to the countertop manufacturer for drilling of the holes. Ø 35 mm 203 mm Max Spout Hole 2. Apply silicone sealant to the underside of the concealing plate. Concealing Plate 3

4 3. Insert the tap through the mounting hole. 4. Partially thread the screws into the ring. 4

5 5. Fit the fibre and metal washers onto the threaded shank Fibre Washer Install the ring leaving approximately 6 mm between the ring and the countertop. 6 mm Ring Metal Washer 6. Turn the ring until the screws are to the front and the back. Tighten the screws securely and evenly. 5

6 Remote Valve 7. Apply silicone sealant to the underside of the remote valve. Install the remote valve through the hole in the countertop. Hot Cold On 8. Before tightening the remote valve, make sure that the cold water supply is on the left hand side. 9. Partially thread the screws into the ring. 6

7 Countertop 10. Slide the washer onto the remote valve threaded shank. Install the ring leaving approximately 6 mm between the ring and the countertop. Washer Ring 6 mm Ring 11. Turn the ring until the screws are to the front and the back. Tighten the screws securely and evenly. 7

8 Spout Connection 12. Connect the inlet hose to the spout connection. Mixed Inlet Hose 13. Connect and tighten the supply hoses. Note! If the sink installation requires that you coil the supply hoses, maintain a 76 mm diameter inside the coil. Ø 76 mm Min Cold Hot 14. Check for leaks. 8

9 15. Remove the aerator. Key 16. Flush the lines. 17. Reinstall the aerator. Key 9

10 Spare Parts ** Spout Setscrew ** Handle Setscrew ** Ball Joint Spring O-Ring ** Tube ** Disk Friction Cup Bearing Check Valve ** Tube Spring Concealing Plate O-Ring ** Top Plate ** Base O-Ring Check Valve Kit Valve ** Mounting Nut Adapter Shank Sprayhead Aerator Valve Body w/hoses Washer Washer Key Washer Threaded Ring Screw Screw Threaded Ring **Finish/color code must be specified when ordering 10

11 dimensions 52 mm 337 mm Max 203 mm Max 102 mm 176 mm 227 mm Ø 67 mm Ø 67 mm 110 mm 64 mm Max 1-1/4" 2" 64 mm 590 mm All dimensions in mm Maintenance Cleaning Caution! Risk of product damage. Many cleaners contain abrasive and chemical substances, and should not be used for cleaning stainless steel, enamel, plated or plastic fittings. These finishes should be cleaned using a mild washing up detergent or soap solution, rinsed and then wiped dry with a soft clean cloth. 11

12 Like anything of lasting quality, Kohler tapware and fittings require a certain amount of periodic care to preserve their lustrous finish. Clean your new Kohler tapware and fittings with a mild soap, rinse thoroughly with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any water from metal surfaces. Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to dry metal, not an abrasive or rubbing action. Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, or chemicals that can damage the finish. By taking the time to dry your tapware often, soap and water deposits can be prevented. Failure to comply with these cleaning instructions may void Kohler s warranty obligations. CO For warranty information, please visit our website: Australia: New Zealand: Care and cleaning SALES & SERVICE NEW ZEALAND KOHLER NZ LTD. Free Ph: (0800 KOHLER) Free Fax: AUSTRALIA KOHLER CO. Free Ph: Free Fax: Kohler Co., March